| Date |
Text |
| 2021-07-12 09:58:08 | 1ST REVIEW FBC-2020 PLUMBING |
| | PERMIT- 21060433 |
| | 7/9/21 |
| | |
| | CODES IN EFFECT: |
| | FBC P- FLORIDA PLUMBING CODE 7TH EDITION 2020 |
| | FBC ACC- FLORIDA ACCESSIBILITY CODE 7TH EDITION 2020 |
| | FBC B- FLORIDA BUILDING CODE 7TH EDITION 2020 |
| | FBC EC- FLORIDA ENERGY CONSERVATION CODE 7TH EDITION |
| | 2020 |
| | FS- FLORIDA STATUTES |
| | FAC- FLORIDA ADMINISTRATIVE CODE |
| | WPB- WEST PALM BEACH AMENDMENTS TO THE FBC |
| | |
| | PLAN REVIEW RESULTS: DENIED. |
| | |
| | 1) SHEET P1.0: REVISE THE 2020 FBC 7TH EDITION CODE |
| | SECTION TEXT TO MATCH THE TEXT LISTED UNDER SECTIONS |
| | 454.1.3.1.2, 454.1.3.1.6, AND 454.1.3.1.9. RED LINE |
| | TEXT HAS BEEN ADDED TO THESE SECTIONS IN THE NEW 2020 |
| | 7TH EDITION CODE WHICH IS PERTINENT TO THE DESIGN OF |
| | THE POOL- SECTION 107.2.1 WPB. |
| | |
| | 2) P1.1 & P1.2: A COMPLETE REVIEW OF THE REQUIRED |
| | PLUMBING FIXTURE COUNTS FOR THE DAY POOL AND SALT SPA |
| | CANNOT BE COMPLETED AT THIS TIME DUE TO A LACK OF |
| | INFORMATION ON THE PLANS- THE NUMBER OF PLUMBING |
| | FIXTURES HAS NOT BEEN CALCULATED BY THE SQUARE FOOTAGE |
| | AREAS OF THE POOL AND SPA AS REQUIRED BY TABLE 454.16.1 |
| | FBC B. BECAUSE RESTROOM FACILITIES FOR THE DAY POOL AND |
| | SALT SPA ARE BEING PROVIDED BY THE HOTEL BUILDING, |
| | PLEASE REVIEW THE EXCEPTION UNDER SECTION 454.1.6.1.1 |
| | FBC B AND PROVIDE: A) THE FIXTURE REQUIREMENT FOR THE |
| | BUILDING. IF IT EXCEEDS THE REQUIREMENT IN TABLE |
| | 454.1.6.1 THEN THE BUILDING REQUIREMENT SHALL REGULATE |
| | THE FIXTURE COUNT, OTHERWISE THE FIXTURE COUNT SHALL BE |
| | BASED ON THE REQUIREMENT FOR THE POOL. UNDER NO |
| | CIRCUMSTANCES SHALL THE FIXTURE COUNTS BE CUMULATIVE. |
| | B) WOMEN'S RESTROOMS SHALL HAVE A RATIO OF THREE TO TWO |
| | WATER CLOSETS PROVIDED FOR WOMEN AS THE COMBINED TOTAL |
| | OF WATER CLOSETS AND URINALS PROVIDED FOR MEN. LAVATORY |
| | COUNTS SHALL BE EQUAL. |
| | |
| | 3) P1.1: PLEASE VERIFY THE HOTEL LOCKER ROOM BATHROOM |
| | IS IN COMPLIANCE WITH SECTION 454.1.6.1.3 FBC B AND ARE |
| | CONSTRUCTED OF CONCRETE OR OTHER NONABSORBENT |
| | MATERIALS, WHICH HAVE A SMOOTH, SLIP-RESISTANT FINISH, |
| | AND SLOPE TO FLOOR DRAINS. |
| | |
| | 4) P1.1: LABEL THE LOCATION OF THE POOL LIFT AND SHOW |
| | THE REQUIRED CLEAR DECK SPACE- SECTIONS 242.2, |
| | 1009.2.1, & 1009.2.3 FBC ACC, AND SECTION 454.1.2.5.6 |
| | FBC B. |
| | |
| | 5) P1.0: THE POOL LIFT INFORMATION UNDER SPLASH SERIES |
| | INDICATES THE LIFTS ARE THIRD PARTY TESTED & VERIFIED |
| | ADA COMPLIANT AND STATE OF CALIFORNIA COMPLIANT. PLEASE |
| | SUBMIT CERTIFICATION DOCUMENTATION THE LIFTS ARE TESTED |
| | AND VERIFIED ADA COMPLIANT FOR USE IN THE STATE OF |
| | FLORIDA. PLEASE MARK OR HIGHLIGHT WHICH MODEL IN THE |
| | SCHEDULE IS PROPOSED TO BE INSTALLED- SECTION 107.2.1 |
| | WPB. |
| | |
| | 6) P1.0: SUBMIT MANUFACTURER'S SPECIFICATIONS AND |
| | INSTALLATION GUIDELINES FOR THE PROPOSED LIFT WITH |
| | APPROVAL STAMPS BY THE ENGINEER OF RECORD- SECTION |
| | 107.3.4 WPB. |
| | |
| | 7) P1.0: PLEASE PROVIDE ON THE PLAN OR ON A |
| | SUPPLEMENTAL PLAN ADDITIONAL ENLARGED INSTALLATION |
| | DETAILS FOR THE LIFT THAT INDICATE COMPLIANCE WITH |
| | SECTIONS 1009.2.2 SEAT LOCATION, 1009.2.3 CLEAR DECK |
| | SPACE, 1009.2.4 SEAT HEIGHT, 1009.2.5 SEAT WIDTH, |
| | 1009.2.6 FOOTRESTS AND ARMRESTS, 1009.2.7 OPERATION. A) |
| | VERIFY COMPLIANCE WITH SECTION 1009.2.9 LIFTING |
| | CAPACITY. SINGLE PERSON POOL LIFTS SHALL HAVE A WEIGHT |
| | CAPACITY OF 300 POUNDS MINIMUM AND BE CAPABLE OF |
| | SUSTAINING A STATIC LOAD OF AT LEAST ONE AND A HALF |
| | TIMES THE RATED LOAD. |
| | |
| | 8): DS3.0 & DS3.3: PROVIDE A CIVIL PLAN OR SITE UTILITY |
| | PLAN SHOWING HOW WATER IS BEING SUPPLIED TO THE POOL |
| | AND THE LOCATION OF THE REQUIRED BACKFLOW PREVENTER- |
| | SECTIONS 454.1.6.3 FBC B AND SECTION 608.7 FBC P. |
| | PLEASE CLARIFY IF THE WATER SUPPLY LINE (AP7) TO THE |
| | COLLECTOR TANK IS ALSO THE MAIN WATER SUPPLY LINE TO |
| | THE POOL- SECTION 454.1.6.5.11 FBC B. PLEASE NOTE THAT |
| | A FL. LICENSED PLUMBING CONTRACTOR SHALL OBTAIN |
| | SEPARATE PERMITS FOR INSTALLATION OF THE WATER LINE AND |
| | AUTO FILL DEVICE, AND FOR THE REQUIRED BACKFLOW |
| | PREVENTER IN ACCORDANCE WITH FL. STATUTE 489.105, |
| | SECTION 105.1 WPB AND SEC. 90-33 WPB CODE OF |
| | ORDINANCES. PLEASE INCLUDE PLUMBING PIPING INSTALLATION |
| | DETAILS AND SPECIFICATIONS IN COMPLIANCE WITH SECTION |
| | 606 FBC P. |
| | |
| | 9) DS3.3: PROVIDE A CIVIL PLAN OR SITE UTILITY PLAN |
| | SHOWING HOW WASTE WATER FROM THE POOL WILL BE DRAINED |
| | TO AN APPROVED PLACE OF DISPOSAL- SECTION 454.1.6.5.15 |
| | FBC B, AND SECS. 90-126 & 203 WPB CODE OF ORDINANCES. |
| | PLEASE INCLUDE PLUMBING PIPING DETAILS AND |
| | SPECIFICATIONS IN COMPLIANCE WITH SECTION 704 FBC P. |
| | |
| | 10) DS3.3: SUBMIT MANUFACTURER'S SPECIFICATIONS FOR |
| | RECIRCULATION AND TREATMENT EQUIPMENT INCLUDING THE |
| | FILTERS, CHEMICAL CONTROLLER, SALT CHLORINE GENERATOR, |
| | AND TREATMENT FEEDERS SHOWING THE EQUIPMENT CONFORMS |
| | WITH REQUIRED STANDARDS NSF/ANSI STANDARD 50, |
| | CIRCULATION SYSTEM COMPONENTS AND RELATED MATERIALS FOR |
| | SWIMMING POOL, SPAS/HOT TUBS, DATED APRIL 2007- SECTION |
| | 454.1.6.5.1 FBC B. |
| | |
| | 11) DS3.0 & DS3.3: SUBMIT MANUFACTURER'S SPECIFICATIONS |
| | FOR THE MAIN DRAIN AND COVER SHOWING CONFORMANCE WITH |
| | THE ANSI/APSP 16 STANDARD- 454.1.6.5.10.2 FBC P. |
| | PROVIDE AN ENLARGED MAIN DRAIN DETAIL IN COMPLIANCE |
| | WITH SECTION 454.1.6.5.10.2 FBC B. |
| | |
| | 12) DS3.2: PLEASE MODIFY THE EQUALIZER LINE INLET |
| | DETAIL TO SHOW A SPRING-LOADED CHECK VALVE WILL BE |
| | INSTALLED THAT WILL NOT ALLOW DIRECT SUCTION ON THE |
| | LINE, AND A PROTECTIVE COVER WILL BE INSTALLED THAT |
| | CONFORMS TO ASME/ANSI A112.19.8- SECTION |
| | 454.1.6.5.3.2.3 FBC B. |
| | |
| | 13) DS3.2: SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE |
| | SKIMMER- SECTION 454.1.6.5.3.2 FBC B. VERIFY THAT |
| | PREVAILING WIND DIRECTION AND THE POOL OUTLINE WAS |
| | CONSIDERED BY THE DESIGNER IN THE SELECTION OF SKIMMER |
| | LOCATIONS- SECTION 454.1.6.5.3.2.2 FBC B. |
| | |
| | 14) DS3.3: SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE |
| | RECIRCULATION PUMP, CARTRIDGE FILTER, AND COLLECTOR |
| | TANK- SECTIONS 454.1.6.5.4, 454.1.6.5.5 & 454.1.6.510.5 |
| | FBC P. PLEAS LABEL ALL EQUIPMENT IN THE INDOOR |
| | EQUIPMENT ROOM AND OUTDOOR EQUIPMENT AREA THAT RELATIVE |
| | TO THEW SCHEDULE ON THE PLAN- SECTION 107.2.1 WPB. |
| | |
| | 15) DS3.3: PROVIDE TOTAL DYNAMIC HEAD CALCULATIONS TO |
| | VERIFY PUMP SIZING AND PUMP SELECTION SHOWN IN THE PUMP |
| | CURVE- SECTION 454.1.6.5.4 FBC B. THE CALCULATIONS |
| | SHALL INCLUDE THE CALCULATED HEAD FOR PIPING AND |
| | EQUIPMENT. |
| | |
| | 16) DS3.0 & DS3.3: SHOW THE FLOW VELOCITIES OF THE |
| | PRESSURE PIPING AND THE SUCTION PIPE FROM THE PUMP TO |
| | THE COLLECTOR TANK IN THE PIPING DIAGRAM- SECTION |
| | 454.1.6.5.8 FBC B. |
| | |
| | 17) DS3.0 & DS3.3: SHOW THE FLOW VELOCITIES OF THE MAIN |
| | DRAIN, GUTTER LINE, AND EQUALIZER LINE PIPING IN THE |
| | PIPING DIAGRAM- SECTION 454.1.6.5.8 FBC B. |
| | |
| | 18) DS3.3: THE PLUMBING DIAGRAM DOES NOT SHOW THE |
| | EQUALIZER LINE DRAINING INTO THE COLLECTOR TANK- |
| | SECTION 454.1.6.5.3.2.3 FBC B. |
| | |
| | 19) P1.0, DS3.0: BASED ON THE PLAN NOTE ON P1.0, PLEASE |
| | INDICATE IF A TIME CLOCK WILL BE INSTALLED, AND THAT IF |
| | IT IS INSTALLED, THE RECIRCULATION SYSTEM SHUT DOWN |
| | TIME WILL NOT REDUCE THE POOL TURNOVER RATE TO LESS |
| | THAN A MINIMUM OF FOUR TURNOVERS OF THE POOL VOLUME PER |
| | DAY. CONSIDERING THE POOL IS DESIGNED AT A 100 GPM FLOW |
| | AT A 4.76 -HOUR TURNOVER TIME- FOUR TURNOVERS PER DAY |
| | AT 4.76 HOURS EA. = 19 HOURS OF RECIRCULATION OPERATION |
| | TIME. THE NOTE INDICATES THE TIMER MAY LIMIT OPERATION |
| | TO 3 HOURS BEFORE OPENING AND 3 HOURS AFTER CLOSING, |
| | HOWEVER THE POOL RULES INDICATE THE POOL IS ONLY OPEN |
| | FROM DAWN TO DUSK SECTION 454.1.6.5.2 FBC B. PLEASE |
| | REVISE THE NOTE TO INDICATE THE ACTUAL NUMBER OF HOURS |
| | PER DAY THAT THE RECIRCULATION SYSTEM SHALL RUN. |
| | |
| | 20) DS3.3: VERIFY FLOW RATE INDICATORS WILL BE |
| | INSTALLED ON THE RETURN PIPING AND SUBMIT |
| | MANUFACTURER'S SPECIFICATIONS- SECTION 454.1.6.5.13 FBC |
| | B. |
| | |
| | 21) DS3.3: PLEASE INDICATE WHAT METHOD WILL BE USED TO |
| | CLEAN THE POOL- SECTION 454.1.6.5.12 FBC P. |
| | |
| | 22) SS4: PROVIDE THE GPM FLOW OF THE SKIMMER LINE IN |
| | COMPLIANCE WITH SECTION 454.1.6.5.3.2.1 FBC B. |
| | |
| | 23) SS4 & SS4.2: THE PLUMBING DIAGRAM ON SS4 DOES NOT |
| | SHOW THE SKIMMER AND THE EQUALIZER LINES DRAINING INTO |
| | THE COLLECTOR TANK- SECTIONS 454.1.6.5.3.2.1 & |
| | 454.1.6.5.3.2.2 FBC B. |
| | |
| | 24) SS4: SUBMIT MANUFACTURER'S SPECIFICATIONS FOR |
| | RECIRCULATION AND TREATMENT EQUIPMENT INCLUDING THE |
| | FILTERS, CHEMICAL CONTROLLER, SALT CHLORINE GENERATOR, |
| | AND TREATMENT FEEDERS SHOWING THE EQUIPMENT CONFORMS |
| | WITH REQUIRED STANDARDS NSF/ANSI STANDARD 50, |
| | CIRCULATION SYSTEM COMPONENTS AND RELATED MATERIALS FOR |
| | SWIMMING POOL, SPAS/HOT TUBS, DATED APRIL 2007- SECTION |
| | 454.1.6.5.1 FBC B. |
| | |
| | 25) SS4.0 & SS4.4: SUBMIT MANUFACTURER'S SPECIFICATIONS |
| | FOR THE MAIN DRAIN AND COVER SHOWING CONFORMANCE WITH |
| | THE ANSI/APSP 16 STANDARD- 454.1.6.5.10.2 FBC P. |
| | PROVIDE AN ENLARGED MAIN DRAIN DETAIL IN COMPLIANCE |
| | WITH SECTION 454.1.6.5.10.2 FBC B. |
| | |
| | 26) SS4.1: PROVIDE AN EQUALIZER DETAIL. SHOW A |
| | SPRING-LOADED CHECK VALVE WILL BE INSTALLED THAT WILL |
| | NOT ALLOW DIRECT SUCTION ON THE LINE, AND A PROTECTIVE |
| | COVER WILL BE INSTALLED THAT CONFORMS TO ASME/ANSI |
| | A112.19.8- SECTION 454.1.6.5.3.2.3 FBC B. |
| | |
| | 27) SS4.2: SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE |
| | RECIRCULATION PUMP, CARTRIDGE FILTER, AND COLLECTOR |
| | TANK- SECTIONS 454.1.6.5.4, 454.1.6.5.5 & 454.1.6.510.5 |
| | FBC P. PLEAS LABEL ALL EQUIPMENT IN THE INDOOR |
| | EQUIPMENT ROOM AND OUTDOOR EQUIPMENT AREA THAT RELATIVE |
| | TO THEW SCHEDULE ON THE PLAN- SECTION 107.2.1 WPB. |
| | |
| | 28) SS4.0 & SS4.2: SHOW THE FLOW VELOCITIES OF THE |
| | PRESSURE PIPING AND THE SUCTION PIPE FROM THE PUMP TO |
| | THE COLLECTOR TANK IN THE PIPING DIAGRAM- SECTION |
| | 454.1.6.5.8 FBC B. |
| | |
| | 29) SS4.2: PROVIDE TOTAL DYNAMIC HEAD CALCULATIONS TO |
| | VERIFY PUMP SIZING AND PUMP SELECTION SHOWN IN THE PUMP |
| | CURVE- SECTION 454.1.6.5.4 FBC B. THE CALCULATIONS |
| | SHALL INCLUDE THE CALCULATED HEAD FOR PIPING AND |
| | EQUIPMENT. |
| | |
| | 30) P1.1: PROVIDE A WATER SUPPLY PIPING LAYOUT AND |
| | RISER DRAWING FOR INSTALLATION OF THE HOSE BIB AND POOL |
| | SHOWER- SECTION 602.2 FBC P AND 107.3.5.1.3 WPB. PLEASE |
| | PROVIDE EQUIPMENT SCHEDULES FOR THE FIXTURES ON THE |
| | PLAN- SECTIONS 412.3 & 608.16.4.2 FBC P. A) INDICATE |
| | HOW WATER FROM THE SHOWER WILL BE DRAINED TO AN |
| | APPROVED PLACE OF DISPOSAL- SECS. 90-126 & 203 WPB CODE |
| | OF ORDINANCES. PLEASE NOTE THE SHOWER DETAIL DOES NOT |
| | SHOW A DRAIN OR FLOOR SLOPE. |
| | |
| | 31) PLEASE SHOW COMPLIANCE WITH THE FOLLOWING SECTIONS |
| | FROM THE FBC EC: |
| | C404.9.1 HEATERS. THE ELECTRIC POWER TO ALL HEATERS |
| | SHALL BE CONTROLLED BY A READILY ACCESSIBLE ON-OFF |
| | SWITCH THAT IS AN INTEGRAL PART OF THE HEATER, MOUNTED |
| | ON THE EXTERIOR OF THE HEATER, OR EXTERNAL TO AND |
| | WITHIN 3 FEET (914 MM) OF THE HEATER. OPERATION OF SUCH |
| | SWITCH SHALL NOT CHANGE THE SETTING OF THE HEATER |
| | THERMOSTAT. SUCH SWITCHES SHALL BE IN ADDITION TO A |
| | CIRCUIT BREAKER FOR THE POWER TO THE HEATER. GAS-FIRED |
| | HEATERS SHALL NOT BE EQUIPPED WITH CONTINUOUSLY BURNING |
| | IGNITION PILOTS. |
| | C404.9.2 TIME SWITCHES. TIME SWITCHES OR OTHER CONTROL |
| | METHODS THAT CAN AUTOMATICALLY TURN OFF AND ON HEATERS |
| | AND PUMP MOTORS ACCORDING TO A PRESET SCHEDULE SHALL BE |
| | INSTALLED FOR HEATERS AND PUMP MOTORS. HEATERS AND PUMP |
| | MOTORS THAT HAVE BUILT-IN TIME SWITCHES SHALL BE IN |
| | COMPLIANCE WITH THIS SECTION. |
| | EXCEPTIONS: |
| | 1. WHERE PUBLIC HEALTH STANDARDS REQUIRE 24-HOUR PUMP |
| | OPERATION. |
| | 2. PUMPS THAT OPERATE SOLAR- AND WASTE-HEAT-RECOVERY |
| | POOL HEATING SYSTEMS. |
| | C404.9.3 COVERS. OUTDOOR HEATED SWIMMING POOLS AND |
| | OUTDOOR PERMANENT SPAS SHALL BE EQUIPPED WITH A |
| | VAPOR-RETARDANT COVER ON OR AT THE WATER SURFACE OR A |
| | LIQUID COVER OR OTHER MEANS PROVEN TO REDUCE HEAT LOSS. |
| | |
| | 32) P2.0: PLEASE NOTE THAT SEPARATE PERMITS ARE |
| | REQUIRED FOR INSTALLATION OF THE POOL HEATER AND GAS |
| | PIPING, THE EQUIPMENT CORRAL, THE POOL FENCE, AUTO FILL |
| | WATER LINE AND BACKFLOW PREVENTER, SITE DRAINAGE |
| | PIPING, AND THE INSTALLATIONS OF THE HOSE BIBS AND POOL |
| | SHOWER- SECTION 105.1 & 107.2.1 WPB. |
| | |
| | WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. |
| | |
| | CHRISTOPHER L. COLE |
| | MECHANICAL/PLUMBING PLANS EXAMINER |
| | 401 CLEMATIS STREET |
| | WEST PALM BEACH FL 33401 |
| | 561-805-6719 |
| | [email protected] |
| | |
