| Date |
Text |
| 2021-03-19 14:06:18 | 1ST REVIEW FBC-2020 RES. |
| | PERMI- 21020263 |
| | 3/19/2021 |
| | |
| | CODES IN EFFECT: |
| | FBC RES- FLORIDA RESIDENTIAL BUILDING CODE 7TH EDITION |
| | 2020 |
| | FBC FG- FLORIDA FUEL GAS CODE 7TH EDITION 2020 |
| | NFPA 58 |
| | FS- FLORIDA STATUTES |
| | FAC- FLORIDA ADMINISTRATIVE CODE |
| | WPB- WEST PALM BEACH AMENDMENTS TO THE FBC |
| | |
| | PLAN REVIEW RESULTS: DENIED. |
| | |
| | 1) PROVIDE A GAS RISER DRAWING- SECTION 107.3.5.3 WPB. |
| | REFER TO NFPA 58 AND PROVIDE: |
| | |
| | A) TYPES AND SIZES OF PIPING TO BE INSTALLED. |
| | |
| | B) DELIVERY PRESSURE AT THE TANK. |
| | |
| | C) TOTAL BTU LOAD AND INDIVIDUAL APPLIANCE BTU LOADS. |
| | |
| | D) TOTAL DEVELOPED LENGTH OF THE SYSTEM FROM THE METER |
| | TO THE MOST REMOTE APPLIANCE OUTLET. |
| | |
| | E) BRANCH AND CUT PIPE LENGTH MEASUREMENTS. |
| | |
| | G) LOCATIONS OF REGULATORS, SHUTOFF VALVES, AND PIPE |
| | UNIONS. |
| | |
| | H) OUTLET PRESSURES AT REGULATORS. |
| | |
| | I) LOCATIONS AND TYPES OF PIPE SLEEVES (IF APPLICABLE). |
| | |
| | 2) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE 250 |
| | GALLON UG LP TANK SHOWING THE TANK AND DOME HAVE BEEN |
| | DESIGNED, FABRICATED, TESTED AND MARKED (STAMPED) IN |
| | ACCORDANCE WITH THE REGULATIONS AS REQUIRED BY THE |
| | REGULATORY AGENCIES AND COMPLIANCE STANDARDS LISTED IN |
| | SECTION 5.2.1.1 NFPA 58. |
| | |
| | 3) PROVIDE A UG LP TANK HOLD-DOWN DETAIL SHOWING HOW |
| | THE TANK WILL BE ANCHORED TO PREVENT FLOTATION, |
| | COLLAPSE, OR LATERAL MOVEMENT- SECTION 6.6.1.6 NFPA-58. |
| | PLEASE INCLUDE A FRONT AND SIDE ELEVATION VIEW THAT |
| | SHOWS THE BURIAL DEPTH, ANCHORING BASE MATERIAL, AND |
| | THE TYPES, SIZES, AND NUMBERS OF ANCHORS, CABLES OR |
| | STRAPS, AND THE TYPE OF PROTECTIVE SLEEVES FOR THE |
| | CABLES OR STRAPS. |
| | |
| | 4) THE UG LP TANK SHALL BE PROTECTED AGAINST CORROSION |
| | BY INSTALLATION OF A CATHODIC PROTECTION SYSTEM |
| | CONSISTING OF A SACRIFICIAL ANODE OR AN IMPRESSED |
| | CURRENT ANODE PER SECTIONS 5.2.1.11 & 6.6.6.1(I) NFPA |
| | 58. INDICATE THE TYPE OF PROTECTION AND SUBMIT |
| | MANUFACTURER'S SPECIFICATIONS- SECTION 6.17.1 NFPA 58. |
| | |
| | 5) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE |
| | REGULATORS MARKED UP TO SHOW THE SELECTED MODE, INLET |
| | AND OUTLET PRESSURES AND PIPE SIZES- SECTION 6.10.1 |
| | NFPA 58. |
| | |
| | 6) SUBMIT MANUFACTURER'S DATA SHEET FOR THE GENERATOR |
| | SHOWING THE BTU LOAD AND INPUT PRESSURE- SECTION- |
| | 107.2.1 WPB. |
| | |
| | WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. |
| | |
| | CHRISTOPHER L. COLE |
| | MECHANICAL/PLUMBING PLANS EXAMINER |
| | 401 CLEMATIS STREET |
| | WEST PALM BEACH FL 33401 |
| | 561-805-6719 |
| | [email protected] |
| | |
