| Date |
Text |
| 2006-08-21 00:00:00 | ******DENIED***** |
| | REFERENCE: FBC-2004 FUEL GAS |
| | FBC-2004 CHAPTER 1 |
| | |
| | THE FOLLOWING INFORMATION IS REQUIRED |
| | FOR GAS PLAN REVIEW ON THE ISOMETRIC |
| | DRAWING FOR A PERMIT: |
| | |
| | 1. SUBMIT AN ISOMETRIC DRAWING THAT |
| | CLEARLY SHOWS ALL CUT SECTIONS OF PIPE |
| | AND CORRESPONDING LENGTHS PER FBC-2004 |
| | FUEL GAS CODE. PLEASE INDICATE ON THE |
| | ISOMETRIC DRAWING EXISTING AND NEW. |
| | |
| | 2. SHOW TYPE OF PIPING MATERIAL BEING |
| | INSTALLED, ALL PIPE SIZES, (AND THE EDH |
| | NUMBER OF CORRUGATED STAINLESS STEEL |
| | TUBING FOR EACH PIPE SIZE BEING USED. |
| | PLEASE INDICATE ON THE DRAWING IF THE |
| | GALVANIZED PIPE IS ABOVE OR BELOW |
| | GROUND. NOTE: GALVANIZED PIPE BELOW |
| | GROUND IS UNACCEPTABLE PER FBC-2004, |
| | FUEL GAS, SECTION 404.8. |
| | |
| | 3. TYPE OF GAS, (LP OR NATURAL) PLEASE |
| | INDICATE ON DRAWING. |
| | |
| | 4. BTU LOAD OF EACH APPLIANCE AND THE |
| | TOTAL BTU LOAD ON THE SYSTEM. REFER TO |
| | THE FBC-2004 FUEL GAS CODE SECS. 401.8 |
| | THRU 402.6.1 AND TABLES 402.4(1) THRU |
| | 402.4(33). (NOTE: TOTAL BTU LOAD |
| | INCLUDING EXISTING NEEDS TO BE INDICATED |
| | ON DRAWING. PLEASE REFERENCE ATTACHED |
| | PERMIT INFORMATION SHEET INDICATING SAID |
| | ADDRESS HAS EXISTING GAS.) |
| | |
| | 5. SHOW THE DISTANCE FROM THE POINT OF |
| | DELIVERY, (METER), TO THE MOST REMOTE |
| | OUTLET IN THE BUILDING AND/OR SYSTEM PER |
| | FBC-2004 FUEL GAS CODE APPENDIX A - USE |
| | OF CAPACITY TABLES A.3.1(4). (NOTE: THIS |
| | INCLUDES THE EXISTING GAS SYSTEM IF |
| | APPLICABLE.) |
| | |
| | 6. INDICATE THE DELIVERY PRESSURE (PSI) |
| | PER FBC-2004 FUEL GAS CODE SEC. 402.2. |
| | NATURAL GAS SPECIFY .5 PSI OR 2 PSI. |
| | |
| | 7. SUBMIT MANUFACTURE SHEETS FOR ALL GAS |
| | EQUIPMENT TO VERIFY COMPLIANCE WITH |
| | STANDARDS NFPA 54, NFPA 58, AND THE |
| | FBC-2004 FUEL GAS CODE SEC 402.2 (NOTE: |
| | IF SYSTEM IS A 2LB SYSTEM MANUFACTURER |
| | CUT SHEETS OF REGULATORS REQUIRED. |
| | MANUFACTURER CUT SHEETS OF POOL HEATER |
| | REQUIRED TO VERIFY BTU'S.) |
| | |
| | 8. FBC-2004 CHAPTER 1,SECTION 106.3.4.2: |
| | THE PERSON RESPONSIBLE FOR THE DESIGN OF |
| | THE DRAWING SHALL CLEARLY PRINT AND SIGN |
| | NAME, AND ALSO DATE DRAWING. PLEASE DO |
| | THIS PRIOR TO RESUBMITTING. |
| | |
| | 9. THE FOLLOWING INFORMATION IS REQUIRED |
| | ON THE SUBMITTED BOUNDARY SURVEY. |
| | (A) LOCATION OF GAS METER |
| | (B) LOCATION OF POOL HEATER |
| | |
| | **IN ORDER TO EXPIDITE PLAN REVIEW: WHEN |
| | RESUBMITTING, PLEASE REPLACE ONLY SHEETS |
| | WHICH HAVE CHANGED AND PROVIDE ONE COPY |
| | OF ALL OLD/VOIDED SHEETS FOR REFERENCE |
| | ONLY. NOTE: ONLY ONE CORRECTED DRAWING |
| | IN RED INK FOR REFERENCE FOR |
| | RESUBMITTAL. |
| | |
| | END OF COMMENTS: |
| | |
| | REVIEW BY MIKE PERSON |
| | (561) 805-6730 |
| | FAX (561) 805-6731 |
| | E-MAIL [email protected] |
| | UNDER SUPERVISION OF K.STEVENS |
| | (561) 805-6721 |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
