| 2017-12-06 04:24:19 | 1) CITY RECORDS SHOW A PREVIOUS GAS PERMIT FOR THIS |
| | ADDRESS. THE PLANS INDICATE AN EXISTING GAS METER. THE |
| | BTU LOAD OF THE EXISTING GAS SYSTEM MUST BE ADDED INTO |
| | THE TOTAL BTU LOAD ON THE SYSTEM TO ENSURE THE EXISTING |
| | SYSTEM IS PROPERLY SIZED. IF UNDERSIZED, THE EXISTING |
| | SYSTEM MUST BE REDONE TO ENSURE A SAFE OPERATING |
| | SYSTEM. SUBMIT A GAS PIPING RISER DIAGRAM THAT SHOWS |
| | THE TYPE OF EXISTING APPLIANCE, THE BTU LOAD OF EACH |
| | APPLIANCE, THE PIPE SIZE AND TYPE OF PIPE TO EACH |
| | APPLIANCE, AND THE DISTANCE OF THE LONGEST LENGTH OF |
| | PIPING FROM THE POINT OF DELIVERY TO THE MOST REMOTE |
| | OUTLET AND THE LOAD OF THE SECTION. NOTE: IF THE |
| | EXISTING SYSTEM IS LESS THAN A 2 PSI SYSTEM AND THE |
| | SYSTEM PRESSURE IS INCREASED TO 2 PSI, A LINE PRESSURE |
| | REGULATOR IS REQUIRED AT ALL THE EXISTING APPLIANCES. |
| | FGC SECS. 401.4, 401.8, 402.1, 402.2, 402.3 OR FBCR |
| | SECS.G2412.4, G2412.8, G2413.1, G2413.2, G2413.3. |
| | 2) PERMIT #16020723 SHOWS THE METER AS A 2 PSI GAS |
| | METER BUT THE SUBMITTED GAS DRAWING SHOWS AN EXISTING |
| | .5 PSI GAS METER. IF THE METER IS .5 PSI THEN THE |
| | ENTIRE EXISTING GAS SYSTEM IS UNDERSIZED. IN ADDITION, |
| | THE TANKLESS WATER HEATER ON YOUR GAS DRAWING IS NOT |
| | THE ONLY GAS APPLIANCE ON THIS SYSTEM. I SUGGEST YOU |
| | CONTACT CRAIG MCPHERSON AT 561-805 6684 AND REQUEST A |
| | COPY OF THE GAS DRAWING FROM PERMIT # 16020723 AND |
| | SUBMIT TWO COPIES ALONG WITH YOUR GAS DRAWING FOR |
| | REFERENCE AND ALSO TO USE IN THE SIZING OF THE YOUR |
| | PIPING FOR THE GENERATOR. EXISTING PIPING MAY HAVE TO |
| | BE INCREASED IN SIZE TO ACCOMMODATE THE TOTAL BTU LOAD |
| | ON THE SYSTEM. FBC-FUEL GAS SEC. 401.4. |
| | 3) SHOW THE TYPE OF PIPE AND THE PIPE SIZE OF THE GAS |
| | LINE COMING FROM THE OULET (CONSUMER SIDE) OF THE GAS |
| | METER. |
| | 4) A GAS SIZING TABLE FROM THE MANUFACTURER OF THE PE |
| | PIPE HAS BEEN SUBMITTED FOR A .5 PSI SYSTEM BUT |
| | PREVIOUS CITY RECORDS SHOW THIS AS A 2 PSI SYSTEM. |
| | SUBMIT THE CORRECT SIZING TABLE FOR THE PSI OF THE |
| | SYSTEM. FBC-FUEL GAS SEC.402.3. THE PLANS REFERENCE 3 |
| | DIFFERENT SIZING TABLES. CLARIFY. THE MANUFACTURER'S |
| | SIZING TABLE IS FOR A PRESSURE DROP OF 6.0 IN. W.C. AND |
| | THE TABLES REFERENCED ON THE GAS DRAWINGS ARE FOR A |
| | PRESSURE DROP OF 0.5 IN. W.C. IT CANNOT BE BOTH. |
| | CLARIFY. |
| | 5) THE GAS SYSTEM SHALL BE SIZED IN ACCORDANCE WITH ONE |
| | OF THE METHODS IN FBC - FUEL GAS SEC.402.4. |
| | 6) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE LINE |
| | PRESSURE REGULATOR. FBC- FUEL GAS SEC.410.1. |
| | 7) SHOW THE LOCATION OF ALL MP (STEP-DOWN) REGULATORS. |
| | A LISTED SHUTOFF VALVE SHALL BE INSTALLED IMMEDIATELY |
| | AHEAD OF EACH MP REGULATOR. FBC-FUEL GAS SEC.409.4, |
| | FBC-RESIDENTIAL SEC. G 2420.4. |
| | 8) THE GENERATOR SPECIFICATIONS NOTE THE BTU LOAD OF |
| | THE GENERATOR AT FULL LOAD AS 310,000 BTU'S BUT THE GAS |
| | DRAWING NOTES 288,000 BTU'S. PIPING SYSTEMS SHALL BE |
| | SIZED TO MEET THE MAXIMUM DEMAND OF THE APPLIANCE. |
| | FBC-FUEL GAS SEC.402.1.CLARIFY. |
| | |
| | NOTE: A CCOMPREHENSIVE PLAN REVIEW COULD NOT BE DONE |
| | DUE TO THE CONFLICTING PLANS AND INFORMATION PROVIDED. |
| | ADDITIONAL PLAN REVIEW COMMENTS MAY BE GENERATED UPON |
| | RE-REVIEW OF SUBMITTED CORRECTIONS. |
| | |
| | TIM LARGE |
| | CHIEF PLUMBING INSPECTOR |
| | PLUMBING PLAN REVIEW |
| | 561-805-6692 |
| | [email protected] |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
