City of West Palm Beach eGovPlus

Plan Review Details - Permit 07050622

Plan Review Stops For Permit 07050622

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2007-10-20			Cont ID
Sent By	jwitmer			Date	2007-10-20	Time	10:11	Rev Time	1.50
Received By	jwitmer			Date	2007-10-20	Time	09:53	Sent To

Notes

2007-10-20 10:28:11	BUILDING PLAN REVIEW
	PERMIT: 07050622
	ADD: 540 CLEMATIS
	CONT: KDN CONSTRUCTION
	TEL: (561)662-1002


	FL BLD CODE= 2004 FLORIDA BUILDING CODE
	W/ 2006 FBC REVISIONS
	* WEST PALM BEACH AMENDMENTS

	2NDREVIEW
	ACTION: DENIED

	1)--- VERY IMPORTANT STATEMENT ---
	PLEASE DO NOT IGNORE!
	WHEN RESUBMITTING PLANS PLEASE INDICATE THE REVISION &
	REMOVE & REPLACE ANY PAGES AS NECESSARY. A TRANSMITTAL
	LETTER LISTING THE ORIGINAL REVIEW COMMENT NUMBER, WITH
	A DESCRIPTION OF THE REVISION MADE, IDENTIFYING THE
	SHEET OR SPECIFICATION PAGE WHERE THE CHANGES CAN BE
	FOUND
	WILL HELP TO EXPEDITE YOUR PERMIT. THANK YOU FOR YOUR
	ANTICIPATED COOPERATION.

	2 ) FL S S 713.13NOTICE OF COMMENCEMENT, TO BE FILED
	WITH THE CLERK OF THE COURT.NOTE: 713.13(2) IF THE
	WORK DESCRIBED IN THE NOTICE OFCOMMENCEMENT IS NOT
	ACTUALLYCOMMENCED WITHIN 90 DAYS AFTER THE RECORDING
	THEREOF, SUCH NOTICE IS NULL & VOID. NOTE: 713.13(6)
	THE POSTING OF THE NOTICE OF COMMENCEMENT AT THE
	CONSTRUCTION SITE BEFORE THE FIRST INSPECTION.

	3)PLANS INDICATE THIS BUILDING TO BE A TYPE IIB
	UNPROTECTED, UNSPRINKLERED, THIS BUILDING IS
	APPROXIMATELY 3,150 SQ FT. PLEASE INDICATE THE MINIMUM
	BUILDING
	TYPE OF CONSTRUCTION. IF THIS SPACE IS TO BE BUILT OUT
	AS A TYPE IIB THE BEARING WALLS WILL AS WELL AS
	NONBEARING WALLS WILL ALL NEED TO BE FIRE RETARDANT
	TREATED WOOD PLEASE SEE TABLE 601 FOOTNOTE C-II . LOOK
	AT TABLE 503 UNDER MERCANTILE AT A BUILDING TYPE VB,
	THE ALLOWABLE AREA OF 9,000 FOR A SINGLE STORY
	BUILDING. IN THIS CATEGORY THE EXTERIOR AND INTERIOR OF
	THE BUILDING DOES NOT REQUIRE THE FIRE RETARDANT
	TREATED WOOD.
	PLEASE PROVIDE :
	110.2* W. P. B. ADMINISTRATIVE CODE, INFORMATION THAT
	IS REQUIRED FOR RECORD KEEPING & FOR CERTIFICATE OF
	OCCUPANCY:
	A) THE EDITION OFTHE CODE UNDER WHICH THE PROJECT WAS
	DESIGNED.NOTE THE BASE CODE IS THE 2004 FBC WITH 2006
	REVISIONS.
	ALSO NOTE TO WHAT LEVEL OF ALTERATION IS BEING
	COMPLETED UNDER THE 2004 FBC EXISTING BUILDING CODE?
	IS THIS A CHANGE IN OCUPANCY?
	B) COMPLIED.
	C)THE TYPE OF CONSTRUCTION AS DEFINED IN TABLE
	503- MERCANTILE & CHAPTER 6, TABLE 601.
	D) COMPLIED.
	E) COMPLIED.
	F) COMPLIED.
	G) SEMI-COMPLIED.SQ. FT. UNDER ROOF (TOTAL) FOR THE
	TOTAL BUILDING NOT TENANT SPACE. TENANT SPACE IS ALSO
	NEEDED AND PROVIDED. THE REQUIEMENT FOR THE TOTAL BLDG
	SQUAREFOOTAGE IS BECAUSE OF THE TYPE II BUILDING
	CLASSIFICATION THE DESIGN PROFESSIONAL HAS INDICATED
	INACTING THE FIRERETARDANT TREATED WOOD. THIS
	BUILDING BEING A ONE STORY BUILDING APPROXIMATELY 3150
	SQ. FT. WILL QUALIFY AS A TYPE V-B.

	4) 2ND REQUEST,THE PLANS DO NOT INDICATE WHERE THE
	PROPERTY LINE WOULD BE OR IF THE FRONT DOOR SWINGS IN
	OR OUT OVER THE PROPERTY LINE? AGAIN, IF THE LEVEL OF
	ALTERATION PROVIDED UNDER THE 2004 FBC, AND IF THIS IS
	A CHANGE OF OCCUPANCY IT MAY OR MAY NOT ENACT CERTAIN
	REQUIREMENTS OF THE CODE. 2004 EXISTING BUILDING CODE
	SECTION 303 ALL BUILDING ALTERATIONS WILL BE CLASSIFIED
	TO ACCORDING TO LEVEL OF ALTERATION. CHANGES IN
	OCCUPANCIES MAY OR MAY NOT INACT CODE ISSUES DEPENDING
	ON THE CATEGORY OF OCCUPANCY, SEE 2004 EXISTING
	BUILDING
	CODE IN CHAPTER 8 CHANGE OF OCCUPANCIES.

	5) COMPLIED.

	6)2ND REQUEST,PLANS INDICATE A RAMP DIRECTLY INSIDE
	THE UNIT WITH NO BOTTOM LANDING.11-4.8.4.(2)
	LANDINGS. ALL LANDINGS ON RAMPS SHALL NOT BE LESS THAN
	60"
	CLEAR, & THE BOTTOM OF EACH RAMP SHALL HAVE NOT LESS
	THAN 72" OF STRAIGHT & LEVEL CLEARENCE. THE PLANS ARE
	MISSING THE BOTTOM LANDING OF 72", DEPENDING ON PART OF
	THE ANSWER TO COMMENT 3A) ANDCOMMENT# 4THIS
	REQUIREMENT MAY NOT HAVE TO BE MET.

	7) 2ND REQUEST, PLEASE PROVIDE DOOR WIDTH FOR ALL NEW
	INTERIOR DOORS. 11-4.13.5 DOORWAYS, MINIMUM CLEAR
	WIDTH: DOORWAY SHALL HAVE A MINIMUM CLEAR OPENING OF
	32" WITH THE DOOR OPEN 90 DEGREES, MEASURED BETWEEN THE
	FACE OF THE DOOR AND THE OPPOSITE STOP. THE PLANS
	INDICATE A 32INCH OPENING TO THE RESTROOM THIS WILL
	ONLY WORK IF THE HINGES ARE SWING CLEAR OF OPENING
	TYPE OF HINGE, THE DOOR WHEN OPENED 90 DEGRESS WILL
	SWING CLEAR OF THE DOOR OPENING OTHERWISE THE MINIMUM
	DOOR OPENING SIZE IS A 2'-10" OR 34INCHES.

	8) 2ND REQUEST, THE RESTROOM DOES NOT PROVIDE
	DIMENSIONS, NOR IS THE 5'-0" TURNING CIRCLE INDICATED
	FOR THE HANDICAPPED RESTROOM. IT APPEARS THE TOLIET IS
	LOCATED IN THE TURNING RADIUS. 11-4.2.3 WHEELCHAIR
	TURNING SPACE. THE SPACE REQUIRED FOR A WHEELCHAIR TO
	MAKE A 180-DEGREE TURN IS A CLEAR SPACE OF 60 INCHES
	(1525 MM) DIAMETER [SEE FIGURE 3 (A)] OR A T-SHAPED
	SPACE [SEE FIGURE 3 (B)].

	9) IS THIS AGAIN A CHANGE IN OCCUPANCY, AND OR A NEW OR
	RECONFIGURED RESTROOM? 11-4.16.2 CLEAR FLOOR SPACE.
	WATER CLOSET.CLEAR FLOOR SPACE FOR WATER CLOSETS NOT IN
	STALLS SHALL COMPLY WITH FIGURE 28 . CLEAR FLOOR SPACE
	MAY BE ARRANGED TO ALLOW EITHER A LEFT-HANDED OR
	RIGHT-HANDED APPROACH.

	10) 2ND REQUEST, THE SIDE GRAB BAR IN THE RESTROOM,
	PLEASE DIMENSION THE SIZE AND LOCATION OF THE GRAB BAR.
	11-4.16.4 GRAB BARS.PLEASE SEE FIGURE# 29 FOR LOCATION
	AND THE MINIMUM SIZE REQUIREMENTS FOR GRAB BARS. THE
	SIDE GRAB BAR IS TO BE A MINIMUM OF 42 INCHES LONG AND
	THE LEADING EDGE TO BE AT 54 INCHES FROM THE CORNER.
	THE BACK BAR ALSO IS NOT DIMENSIONED FOR LENGTH WHICH
	WOULD BE 36" AND ONE END OF THE BACK GRAB BAR BEING 12
	INCHES OF CENTER OF THE WATER CLOSET BEING SET UP FOR A
	LEFTOR RIGHT HANDED SIDE APPROACH, SEE FIGURE 29 FOR
	CLARIFICATION.
	GRAB BARS FOR WATER CLOSETS NOT LOCATED IN STALLS SHALL
	COMPLY WITH SECTION 11-4.26 AND FIGURE 29 . THE GRAB
	BAR BEHIND THE WATER CLOSET SHALL BE 36 INCHES (915 MM)
	MINIMUM.

	11) COMPLIED.

	12)BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED,
	IMPACT FEES MUST BE PAID TO PALM BEACH COUNTY. THE
	ACTUAL PERMIT SET OF PLANS MUST BE STAMPED BY THAT
	OFFICE, AND A COPY OF THE PAID RECEIPT ATTACHED TO THE
	PERMIT APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	BUILDING PLAN REVIEW II
	JIM WITMER C. B. O.


	TEL: (561)805-6715
	FAX: (561)659-8026
	E-MAIL: [email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2007-06-28			Cont ID
Sent By	jwitmer			Date	2007-06-28	Time	18:37	Rev Time	1.11
Received By	jwitmer			Date	2007-06-28	Time	18:37	Sent To

Notes

2007-06-28 19:00:38	BUILDING PLAN REVIEW
	PERMIT: 07050622
	ADD: 540 CLEMATIS
	CONT: KDN CONSTRUCTION
	TEL: (561)662-1002


	FL BLD CODE= 2004 FLORIDA BUILDING CODE
	W/ 2006 FBC REVISIONS
	* WEST PALM BEACH AMENDMENTS

	REVIEW
	ACTION: DENIED

	1)--- VERY IMPORTANT STATEMENT ---
	PLEASE DO NOT IGNORE!
	WHEN RESUBMITTING PLANS PLEASE INDICATE THE REVISION &
	REMOVE & REPLACE ANY PAGES AS NECESSARY. A TRANSMITTAL
	LETTER LISTING THE ORIGINAL REVIEW COMMENT NUMBER, WITH
	A DESCRIPTION OF THE REVISION MADE, IDENTIFYING THE
	SHEET OR SPECIFICATION PAGE WHERE THE CHANGES CAN BE
	FOUND
	WILL HELP TO EXPEDITE YOUR PERMIT. THANK YOU FOR YOUR
	ANTICIPATED COOPERATION.

	2 ) FL S S 713.13NOTICE OF COMMENCEMENT, TO BE FILED
	WITH THE CLERK OF THE COURT.NOTE: 713.13(2) IF THE
	WORK DESCRIBED IN THE NOTICE OFCOMMENCEMENT IS NOT
	ACTUALLYCOMMENCED WITHIN 90 DAYS AFTER THE RECORDING
	THEREOF, SUCH NOTICE IS NULL & VOID. NOTE: 713.13(6)
	THE POSTING OF THE NOTICE OF COMMENCEMENT AT THE
	CONSTRUCTION SITE BEFORE THE FIRST INSPECTION.

	3)PLANS INDICATE THIS BUILDING TO BE A TYPE IIA
	UNPROTECTED, UNSPRINKLERED, THIS BUILDING IS
	APPROXIMATELY 3,150 SQ FT. PLEASE INDICATE THE MINIMUM
	BUILDING
	TYPE OF CONSTRUCTION. IF THIS SPACE IS TO BE BUILT OUT
	AS A TYPE IIA THE BEARING WALLS WILL NEED TO BE 1 HR
	RATED AS WELL AS THE CEILING ROOF ASSEMBLY.PLEASE
	PROVIDE :
	110.2* W. P. B. ADMINISTRATIVE CODE, INFORMATION THAT
	IS REQUIRED FOR RECORD KEEPING & FOR CERTIFICATE OF
	OCCUPANCY:
	A) THE EDITION OFTHE CODE UNDER WHICH
	THE PROJECT WAS DESIGNED.
	ALSO NOTE TO WHAT LEVEL OF ALTERATION IS BEING
	COMPLETED UNDER THE 2004 FBC EXISTING BUILDING CODE? B)
	THE USE AND OCCUPANCY, IN ACCORDANCE WITH THE
	PROVISIONS OF CHAPTER 3. IS THIS A CHANGE OF
	OCCUPANCY?
	C) THE TYPE OF CONSTRUCTION AS DEFINED IN CHAPTER 6,
	TABLE 601.
	D) THEOCCCUPANT LOAD, SEE 1004.
	E) IF AN AUTOMATIC SPRINKLER SYSTEM IS
	PROVIDED, WHETHER THE SPRINKLER SYSTEM
	IS REQUIRED.
	F) ANY SPECIAL STIPULATIONS & CONDITIONS
	OF THE BUILDING PERMIT
	G) SQ. FT. UNDER ROOF (TOTAL) FOR THE TOTAL BUILDING
	NOT TENANT SPACE.

	4)THE PLANS DO NOT INDICATE WHERE THE PROPERTY LINE
	WOULD BE OR IF THE FRONT DOOR SWINGS IN OR OUT OVER THE
	PROPERTY LINE?

	5) THE PLANSALSO INDICATE A HASHED LINE IN FRONT OF THE
	UNIT, IS THIS AAWNING? REQUIRES A SEPERATE PERMIT.

	6) PLANS INDICATE A RAMP DIRECTLY INSIDE THE UNIT WITH
	NO BOTTOM LANDING.11-4.8.4.(2) LANDINGS. ALL LANDINGS
	ON RAMPS SHALL NOT BE LESS THAN 60"
	CLEAR, & THE BOTTOM OF EACH RAMP SHALL HAVE NOT LESS
	THAN 72" OF STRAIGHT & LEVEL CLEARENCE.

	7) PLEASE PROVIDE DOOR WIDTH FOR ALL NEW INTERIOR
	DOORS. 11-4.13.5 DOORWAYS, MINIMUM CLEAR WIDTH: DOORWAY
	SHALL HAVE A MINIMUM CLEAR OPENING OF 32" WITH THE DOOR
	OPEN 90 DEGREES, MEASURED BETWEEN THE FACE OF THE DOOR
	AND THE OPPOSITE STOP.

	8)HANDICAPPED ESTROM THE TOLIET IS LOCATED IN THE
	TURNING RADIUS. 11-4.2.3 WHEELCHAIR TURNING SPACE. THE
	SPACE REQUIRED FOR A WHEELCHAIR TO MAKE A 180-DEGREE
	TURN IS A CLEAR SPACE OF 60 INCHES (1525 MM) DIAMETER
	[SEE FIGURE 3 (A)] OR A T-SHAPED SPACE [SEE FIGURE 3
	(B)].

	9) 11-4.16.2 CLEAR FLOOR SPACE. WATER CLOSET.CLEAR
	FLOOR SPACE FOR WATER CLOSETS NOT IN STALLS SHALL
	COMPLY WITH FIGURE 28 . CLEAR FLOOR SPACE MAY BE
	ARRANGED TO ALLOW EITHER A LEFT-HANDED OR RIGHT-HANDED
	APPROACH.

	10) MISSING THE SIDE GRAB BAR IN THE RESTROOM, PLEASE
	DIMENSION THE SIZE AND LOCATION OF THE GRAB BAR.
	11-4.16.4 GRAB BARS.
	GRAB BARS FOR WATER CLOSETS NOT LOCATED IN STALLS SHALL
	COMPLY WITH SECTION 11-4.26 AND FIGURE 29 . THE GRAB
	BAR BEHIND THE WATER CLOSET SHALL BE 36 INCHES (915 MM)
	MINIMUM.

	11) PLEASE INDICATE COMPLIANCE WWITH COUNTERS AND BARS,
	11-5.2 COUNTERS AND BARS.
	WHERE FOOD OR DRINK IS SERVED AT COUNTERS EXCEEDING 34
	INCHES (865 MM) IN HEIGHT FOR CONSUMPTION BY CUSTOMERS
	SEATED ON STOOLS OR STANDING AT THE COUNTER, A PORTION
	OF THE MAIN COUNTER WHICH IS 60 INCHES (1525 MM) IN
	LENGTH MINIMUM SHALL BE PROVIDED IN COMPLIANCE WITH
	SECTION 11-4.32 OR SERVICE SHALL BE AVAILABLE AT
	ACCESSIBLE TABLES WITHIN THE SAME AREA.

	11-5.6 TABLEWARE AND CONDIMENT AREAS.
	SELF-SERVICE SHELVES AND DISPENSING DEVICES FOR
	TABLEWARE, DISHWARE, CONDIMENTS, FOOD AND BEVERAGES
	SHALL BE INSTALLED TO COMPLY WITH SECTION 11-4.2 (SEE
	FIGURE 54 ).

	12)BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED,
	IMPACT FEES MUST BE PAID TO PALM BEACH COUNTY. THE
	ACTUAL PERMIT SET OF PLANS MUST BE STAMPED BY THAT
	OFFICE, AND A COPY OF THE PAID RECEIPT ATTACHED TO THE
	PERMIT APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	A THOROUGH REVIEW CAN NOT BE MADE AT THIS TIME, AS A
	RESULT OF THE ADDITIONAL INFORMATION REQUESTED
	ADDITIONAL COMMENTS MAY APPEAR THAT WERE NOT PART OF
	THIS REVIEW.

	BUILDING PLAN REVIEW II
	JIM WITMER C. B. O.

	TEL: (561)805-6715
	FAX: (561)659-8026
	E-MAIL: [email protected]

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2007-10-06			Cont ID
Sent By	dpalmer			Date	2007-10-06	Time	18:38	Rev Time	0.00
Received By	dpalmer			Date	2007-10-06	Time	18:38	Sent To

Notes

2007-10-06 18:39:51	2007-10-06 18:39:51

	* DENIED 2ND REVIEW *

	1) NOTE: PLEASE KNOW WITH RESPECT TO THE
	DESIGNER/ENGINEER OF RECORD RESPONSE COMMENTS WHICH
	SEEM TO CONTEST THIS REVIEWER NOTES. SEVERAL OF THE
	ENGINEER RESPONSE NOTES MENTIONS PLANS DATED FEBRUARY
	07, HOWEVER THE PREVIOUS REVIEW WAS DONE ON PLANS
	SUBMITTED WHICH WERE SIGNED, DATED AND SEALED ON
	3/19/07 BY THE ENGINEER OF RECORD.
	PLEASE KNOW THAT THIS OFFICE/REVIEWER ONLY REVIEWS
	THE PLANS WHICH ARE SUBMITTED WITH THE PERMIT
	APPLICATION.
	THE PLANS SUBMITTED FROM THE PREVIOUS REVIEW WERE
	TURNED INTO THIS OFFICE WERE ALSO SUBMITTED BACK WITH
	THIS RE-SUB AS OLD PLANS.
	PLEASE SEE THE SIGNED, DATED AND SEALED PLANS DATED
	3/19/07 FROM THE ENGINEER WERE THE SAME PLANS
	SUBMITTED. PLEASE CHECK THE PLANS SUBMITTED.
	THE PREVIOUS COMMENTS WERE VALID BASED ON THE PLANS
	SUBMITTED ON THE FIRST REVIEW AS SUBMITTED.
	** PLEASE SEE THOSE SAME PLANS HAVE HAD SEVERAL OF THE
	PREVIOUS REVIEW COMMENTS HIGH-LIGHTED.
	EXAMPLE:
	A) PREVIOUS PLANS HAS 65AMP RATED CONDUCTORS ON 100AMP
	DISCONNECTS W/70A OCP.
	B) PREVIOUS PLANS HAVE 244AMPS OF LOAD SHOWN ON A
	300AMP PANEL BEING FED FROM A 100AMP DISCONNECT WITH
	70AMP FUSES.
	C) PREVIOUS PLANS HAD EQUIPMENT/REFRIGERATOR AT FRONT
	DOOR ON GENERAL PURPOSE CIRCUITS.

	** THIS REVIEWER HAS STATED ON ALL REVIEWS PERFORMED BY
	THIS OFFICE THAT IF THERE EVER ANY QUESTIONS, OR
	COMMENTS TO PLEASE DO NOT HESITATE IN CONTACTING THIS
	OFFICE/OR REVIEWER. AT THIS TIME WE MAY GO OVER
	COMMENTS OR EVEN IF A MEETING IS NEEDED WE CAN SCHEDULE
	A TIME TO GO OVER REVIEW COMMENTS.

	**THIS HAS NOT CHANGED, AND ONCE AGAIN IF THERE ARE ANY
	ITEMS WHICH NEED TO BE GONE OVER PLEASE CALL.

	2) NOTE: PLEASE SEE PREVIOUS REVIEW NOTE #2. PLEASE
	SUBMIT LIGHTING PERFORMANCE CALCULATIONS. MAY NOT USE
	METHOD A WHOLE BUILDING CALCULATION FOR THE TENANT
	BUILD OUT.
	PLEASE SEE COMMENTS FROM MECHANICAL REVIEWER. PLEASE
	SEE 13-415.2 AND TABLES.
	PLEASE SEE LIGHTING CONTROLS STILL REQUIRED PER
	13-415.1.ABC.1.1, .1.2. PLEASE SEE THE ONLY DEVICE IS
	THE OS SHOWN AT FRONT DOOR WHICH DOES NOT PROVIDE
	NEEDED COVERAGE IN THE REAR OF SPACE. PLEASE ALSO SEE
	THIS DOES NOT THE MEET THE REQUIREMENTS FOR SEPARATE
	SPACE CONTROLS FOR AREAS WHICH HAVE FLOOR TO CEILING
	HEIGHT PARTITIONS.
	PLEASE ADJUST DEVICES, TIMES FOR DEVICES TO BE CHOSEN.

	3) NOTE: PLEASE SEE PREVIOUS REVIEW NOTE #3 WITH
	RESPECT TO RISER AND TO BE SURE AND COORDINATE ALL WITH
	THE ACTUAL EXISTING RISER. THE LAST SETS OF REVISED
	ELECTRICAL PLANS SUBMITTED TO THE CITY FOR PERMITTING
	AND REVISIONS INDICATES LARGER MAINS BEING TAPPED FORM
	THE EXISTING MAIN AND GUTTER.
	PLEASE SUBMIT COMPLETE LOAD CALCULATIONS ON THE
	EXISTING SERVICE WITH NEW LOADS BEING ADDED.(LOAD
	CALCULATIONS SUBMITTED, HOWEVER NOTE TO REMAIN DUE TO
	KNOWN ADJUSTMENTS WHICH WILL BE NEEDED).
	FOR EXAMPLE, ALL OTHER TENANT MAINS ARE SHOWN AT
	100AMPS, YET THERE IS ANOTHER RESTAURANT/ SANDWICH SHOP
	WHICH HAS A LARGER SERVICE MAIN THAN 100AMPS. PLEASE
	SEE 240, 310, 408, 230, 215.5, 220 ETC. PLEASE ADJUST
	ALL.
	FBC 106.3.5.1.2

	4) NOTE: PLEASE CLARIFY WATER HEATER LOAD AS THE NEW
	CODE REQUIRED STORAGE TYPE WATER HEATER LOADS TO BE
	SHOWN AT 125%. THESE ARE NOW CONSIDERED CONTINUOUS
	LOADS.
	PLEASE SEE 422.13

	** AS THERE WILL BE SEVERAL CHANGES, PLEASE BE SURE TO
	GO OVER COMMENTS FROM ALL TRADES WHICH MAY AFFECT THE
	SCOPE OF WORK ALONG WITH OTHER TRADE REVIEWED SHEETS.


	* IMPORTANT
	ONCE ALL REVIEWS ARE DONE AND PLANS ARE PICKED UP FOR
	CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE ALL
	OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED SHEETS
	INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING. DO NOT
	LEAVE ANY OLD/VOIDED SHEETS IN SETS.
	PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS
	SHOULD BE SUBMITTED FOR REFERENCE.
	THIS WILL HELP IN THE REVIEW PROCESS AND AVOID ANY
	DELAYS.

	** PLEASE BE SURE TO CALL IF THERE ARE ANY QUESTIONS OR
	COMMENTS WITH RESPECT TO THE TYPED COMMENTS ABOVE. IF
	THERE ARE ANY COMMENTS WHICH ARE NOT CLEAR IN ANY WAY,
	NOT UNDERSTOOD OR NOT TYPED IN A CLEAR MANOR, PLEASE DO
	NOT HESITATE IN CONTACTING THIS OFFICE AND THIS
	REVIEWER.


	DEWEY PALMER
	ELECTRICAL PLAN REVIEW II
	CONSTRUCTION SERVICES DEPT.
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2007-06-08			Cont ID
Sent By	dpalmer			Date	2007-06-08	Time	08:19	Rev Time	0.00
Received By	dpalmer			Date	2007-06-07	Time	20:48	Sent To

Notes

2007-06-08 08:20:10	* UNSAT *

	1) NOTE:PLEASE STATE ALL OF THE RELEVANT CODES AS
	ADOPTED FROM THE STATE OF FLORIDA AS OF DECEMBER 8TH,
	2006.
	PLEASE LIST THE FOLLOWING AT A MINIMUM ON ELECTRICAL
	SHEETS AS WELL AS ARCHITECTURAL.
	2004 FBC W/2006 REVISIONS.
	2005 NFPA-70 (NEC).
	2003 NFPA-101 (LS CODE).

	2) NOTE: PLEASE SEE FBC CHAPTER 13 FOR COMPLIANCE FOR
	ENERGY CALCULATIONS/PERFORMANCE CALCULATIONS
	13-415.1.AB1.1, 13-415.2.
	PLEASE SEE MISSING LIGHTING CONTROLS AS REQUIRED PER
	13-415.1.ABC.1.1, .1.2 AND .1.3.
	** AS NO INFORMATION ON SCHEDULING, TYPEOF DEVICES,
	FIXTURES, WATTAGES, OVER RIDES, ETC HAVE BEEN SUBMITTED
	FOR REVIEW, COMMENTS CAN NOT BE MADE AT THIS TIME.

	3) NOTE: PLEASE SEE THE SERVICE AS SHOWN CONTAINS A
	NOTE AT THE BOTTOM WHICH INDICATES EXISTING YET THE
	RISER AS SHOWN INDICATES SOME ITEMS AS NEW?? PLEASE
	CLARIFY ALL SERVICE EQUIPMENT AS SHOWN. PLEASE SEE THE
	PANEL SCHEDULE SHOWS THIS AS A 300AMP PANEL WITH 244
	AMP LOAD, YET THE PANEL IS ONLY BEING FED W/ A 2-POLE
	70AMP BREAKER WITH CONDUCTORS WHICH ARE ONLY RATED AT
	65AMPS??
	PLEASE SEE THE LOAD ON PANEL AS NOTED ABOVE SHOWN AT
	244AMPS, YET THE RISER LOAD CALCULATIONS ARE SHOWN
	SUBSTANTIALLY LESS FOR THIS SAME UNIT??
	PLEASE SEE THERE ARE SEVERAL ITEMS INCORRECT WITH THIS
	RISER AND NEW FEED TO PANEL.
	PLEASE SEE 240, 310, 408, 230, 215.5 ETC.
	PLEASE ADJUST ALL.
	FBC 106.3.5.1.2

	4) NOTE: PLEASE SEE ALL BREAKERS ON THE PANEL SCHEDULE
	ARE 1-POLE BREAKERS? HOW IS THIS POSSIBLE FOR THE
	240/220/208 VOLT UNITS.
	IS ALL EQUIPMENT ON SINGLE POLE BREAKERS?
	PLEASE SEE NEC.

	5) NOTE: PLEASE SEE THE AHU SEEMS TO BE SHOWN WITH 10KW
	LOAD YET THE CONDUCTOR AND BREAKER SIZE IS NOT
	SUFFICIENT PER CODE.
	PLEASE SEE 240.4, 310.16, 424.3B.

	6) NOTE: PLEASE CLARIFY WATER HEATER AS PLANS INDICATES
	A STORAGE TYPE UNIT AND PANEL SCHEDULE INDICATES
	INSTANT TYPE HEATERS.
	PLEASE SEE 422.13 AND THE FOLLOWING COMMENT FOR LOAD
	CALCULATIONS.

	7) NOTE: PLEASE SUBMIT COMPLETE LOAD CALCULATIONS ON
	THE NEW PROPOSED LOAD FOR THIS TENANT SPACE AND FOR THE
	ENTIRE SERVICE FOR EXISTING LOADS AND NEW LOADS BEING
	ADDED TO SERVICE. THE LOAD AS SHOWN ON THE RISER LOAD
	CALCULATIONS IS NOT POSSIBLE.
	PLEASE SEE NEC 220 (ALL), 215.3, 230.42.
	PLEASE BE SURE ALL CONTINUOUS LOADS ARE SHOWN AT 125%

	8) NOTE: PLEASE SEE THE SHOW WINDOW RECEPTACLE IS BEING
	SHOWN ON THE GENERAL RECEPTACLE CIRCUIT WHICH IS NOT
	PERMITTED.
	210.62,220.14, 220.44.

	9) NOTE: PLEASE SEE THE PLANS INDICATE SOME SORT OF
	REFRIGERATOR AT THE FRONT ENTRANCE WHICH IS BEING SHOWN
	ON THE SAME GENERAL RECEPTACLE CIRCUIT AS SHOW WINDOW
	ETC. PLEASE SEE THE VA ON UNIT NEEDS TO BE VERIFIED AS
	THE CIRCUIT MOST LIKELY WILL NEED TO BE DEDICATED.
	PLEASE KNOW AS THE LOADS ARE NOT SHOWN, DETERMINATION
	CAN NOT BE DONE AT THIS TIME.
	PLEASE SEE 430, 422, 422, 220 ETC.
	FBC 106.1.2

	10) NOTE: PLEASE SEE 210.8B2 FOR ALL REQUIRED GFI
	PROTECTED CIRCUITS/RECEPTACLES ON PLANS IN KITCHEN FOOD
	PREP AREAS AND THE LIKE.

	11) NOTE: PLEASE SEE VALUE FOR SCOPE OF WORK IS TO
	INCLUDE ALL LABOR, MATERIALS, EQUIPMENT, DESIGN COST
	ETC., EVEN IF ANY OF THESE ARE OWNER SUPPLIED. PLEASE
	SEE FBC 108.3.

	12) NOTE: PLEASE SEE CU IS BEING SHOWN ON 1-POLE
	CIRCUIT?

	13) NOTE: PLEASE COMPLETE CIRCUITING ON PLANS AND
	COORDINATE WITH THE SUBMITTED PANEL SCHEDULE. PLEASE
	SEE SOME ELECTRICAL ITEMS NOT SHOWING CIRCUITS. PLEASE
	ALSO SEE 700.12F FOR CIRCUITING OF EM/EXT LTS.

	14) NOTE: PLEASE INDICATE THE SUITE/UNIT NUMBER ON
	PLANS/ TITLE BLOCKS.
	FAC 61G1-16.004 FBC 106.1.2

	15) NOTE: PLEASE SEE THE PANEL SCHEDULE INDICATES
	SEVERAL ITEMS BEING EXISTING, HOWEVER AS THIS IS A NEW
	BUILD-OUT FROM PREVIOUS SHELL THIS IS NOT POSSIBLE.
	PLEASE ADJUST. 408.4.
	FBC 106.3.5.1.2


	** PLEASE KNOW AT THIS TIME AS SOME OF THE INSTALLATION
	IS NOT CLEAR, THERE MAY BE COMMENTS IF THE INSTALLATION
	CHANGES AND/OR PERMIT APPLICATION CHANGES.

	* IMPORTANT
	ONCE ALL REVIEWS ARE DONE AND PLANS ARE
	PICKED UP FOR CORRECTIONS, PLEASE BE
	SURE TO COMPLETELY REMOVE ALL OLD/VOIDED
	SHEETS AND ONLY INSERT NEW REVISED
	SHEETS INTO TWO COMPLETE SETS FOR REVIEW
	AND STAMPING. DO NOT LEAVE ANY
	OLD/VOIDED SHEETS IN SETS.
	PLEASE KNOW ONLY ONE SET OF THE
	OLD/VOIDED SHEETS SHOULD BE SUBMITTED
	FOR REFERENCE.
	THIS WILL HELP IN THE REVIEW PROCESS AND
	AVOID ANY DELAYS.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW II
	CONSTRUCTION SERVICES DEPT.
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]
2007-06-08 07:35:12	IN ELEC FOR REVIEW

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	2	Status	F	Date	2007-10-24			Cont ID
Sent By	mwennerg			Date	2007-10-24	Time	13:11	Rev Time	0.00
Received By	mwennerg			Date	2007-10-24	Time	13:11	Sent To

Notes

2007-10-24 13:33:11	*DENIED*

	SOME OF THE PREVIOUS COMMENTS WERE ADDRESSED DIRECTLY
	ON THE PLANS. (SHT A-1) A RESPONSE LETTER (2ND REQUEST)
	WOULD BE HELPFUL AND AS STATED IN THE FIRST REVIEW WILL
	HELP EXPEDITE THE PLAN REVIEW PROCESS.

	1) OK

	2) OK

	3) OK

	4) COMBUSTIBLE WASTE MATERIALS, DUST, AND DEBRIS SHALL
	BE REMOVED FROM THE SITE AT THE END OF EACH SHIFT OR
	MOVE FREQUENTLY AS NECESSARY FOR SAFE OPEARTION.

	5) THE SCOPE OF WORK SHALL NOT INTERFERE OR HINDER
	EMERGENCY RESPONSE ACCESS TO THE PROPERTY OR VICINITY
	THEREOF (INCLUDING STREETS, ALLEYS, FIRE LANES ETC).

	6) CLASSIFY THE HAZARD OF CONTENTS OF
	BUILDING/STRUCTURE AS LOW, ORDINARY OR HIGH.

	7) OK

	8) LOCKS ON EGRESS DOORS SHALL NOT REQUIRE THE USE OF A
	KEY, TOOL OR SPECIAL KNOWLEDGE OR EFFORT OF OPERATION
	FROM THE EGRESS SIDE. (NO DOOR SCHEDULE)

	9) OK

	10) AN EXIT SIGN LIGHT WITH BATTERY BACK-UP CAPABILITY
	SHALL BE REQUIRED TO DIRECT PERSON(S) FROM THE COOKING
	PREPARATION AREA.

	11) SPECIFY THE INTERIOR WALLS AND CEILING FINISH
	MATERIALS IN TERMS OF CLASSA,B OR C.

	12) COMMERCIAL COOKING EQUIPMENT TO COMPLY WITH NFPA
	96, 2001 EDITION.

	13) SEPARATE SHOP DRAWINGS AND PERMITS REQUIRED FOR
	HOOD AND SUPPRESSION SYSTEMS. PLANS INDICATE SEPARATE
	PERMIT FOR FIRE SPRINKLER WHICH PLANS ALSO STATE NOT
	APPLICABLE.


	MIKE WENNERGREN, ASSISTANT FIRE MARSHAL
	FIRE PLAN REVIEW
	FIRE PREVENTION (561) 804-4756

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2007-07-12			Cont ID
Sent By	mawillia			Date	2007-07-12	Time	09:22	Rev Time	0.00
Received By	mawillia			Date	2007-07-12	Time	08:45	Sent To

Notes

2007-07-12 09:18:01	***DENIED***

	DUE TO THE ALTERATION, MODERNIZATION, OR RENOVATION TO
	THIS SITE, THE REQUIREMENTS OF A NEW MERCANTILE
	OCCUPANCY SHALL APPLY.IT SHALL BE SUB-CLASSIFIED AS A
	CLASS C MERCALNTILE (GROSS AREA NOT MORE THAN 3000
	SQUARE FEET).

	01.THE SUITE NUMBER SHALL BE INCLUDED WITH NUMERICAL
	ADDRESS IN THE TITLE BLOCK OF EACH SUBMITTED PLAN
	SHEET.

	02.NFPA 101, LIFE SAFETY CODE, 2003 EDITION SHALL BE
	REFERENCED.

	03.STRUCTURES UNDERGOING CONSTRUCTION, ALTERATION, OR
	DEMOLITION OPERATION SHALL COMPLY WITH NFPA 241.

	04.COMBUSTIBLE WASTE MATERIALS, DUST, AND DEBRIS
	SHALL BE REMOVED FROM THE SITE AT THE END OF EACH SHIFT
	OR MORE FREQUENTLY AS NECESSARY FOR SAFE OPERATION.

	05.THE SCOPE OF WORK SHALL NOT INTERFERE OR HINDER
	EMERGENCY RESPONSE ACCESS TO THE PROPERTY OR VICINITY
	THEREOF (INCLUDING STREETS, ALLEYS, FIRE LANES).

	06.CLASSIFY THE HAZARD OF CONTENTS OF
	BUILDING/STRUCTURE AS LOW, ORDINARY, OR HIGH.

	07.DECLARE THE OCCUPANT LOAD IN NUMBER OF PERSONS FOR
	WHOM MEANS OF EGRESS AND OTHER PROVISIONS ARE
	REQUIRED.

	08.LOCKS ON EGRESS DOORS SHALL NOT REQUIRE THE USE OF
	A KEY, A TOOL, OR SPECIAL KNOWLEDGEOR EFFORT OF
	OPERATION FROM THE EGRESS SIDE.

	09.A SINGLE MEANS OF EGRESS SHALL BE PERMITTED IN A
	CLASS C MERCANTILE PROVIDED THAT THE 75' TRAVEL
	DISTANCE TO THE EXIT IS NOT EXCEEDED.PLEASE
	DEMONSTRATE

	10.AN EXIT SIGN LIGHT, WITH BATTERY BACK-UP
	CAPABILITY, SHALL BE REQUIRED TO DIRECT PERSON(S) FROM
	THE COOKING PREPARATION AREA.

	11.SPECIFY THE INTERIOR WALL AND CEILING FINISH
	MATERIALS IN TERMS OF CLASS A OR CLASS B.

	12.COMMERCIAL COOKING EQUIPMENT SHALL BE ACCORDANCE
	WITH NFPA 96 - 2001 EDITION.

	13.SEPARATE PLANS AND PERMIT REQUIRED FOR BOTH THE
	COOKING HOOD INSTALLATION AND THE HOOD'S SUPPRESSION
	SYSTEM.


	TO EXPEDITE THE PLAN REVIEW PROCESS, INCLUDE A RESPONSE
	LETTER INDICATING WHERE ON THE PLANS EACH ITEM WAS
	ADDRESSED


	CAPT. MICHAEL A. WILLIAMS
	FIRE PLAN REVIEW
	561-805-6722

Review Stop	G			GAS REVIEW
Rev No	2	Status	F	Date	2007-11-03			Cont ID
Sent By	kstevens			Date	2007-11-03	Time	17:07	Rev Time	0.00
Received By	kstevens			Date	2007-11-03	Time	17:07	Sent To

Notes

2007-11-03 17:13:22	DENIED
	REFERENCE: FBC-2004 FUEL GAS

	****FROM PREVIOUS REVIEW:

	1. A SEPARATE GAS PERMIT IS REQUIRED. THE FOLLOWING
	INFORMATION IS REQUIRED FOR THE GAS PERMIT:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.
	****RESPONSE NOTED, BUT COMMENT NOT COMPLETLY
	ADDRESSED. LENGTHS OF PIPE NOT SHOWN.

	B. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE IF BEING USED. ****RESPONSE
	NOTED, BUT COMMENT NOT ADDRESSED. PIPE TYPE NOT
	INDICATED ON LEGEND.

	C. OK

	D. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).
	****RESPONSE NOTED, BUT THIS WILL BE VERIFIED WHEN ALL
	CUT SECTION LENGTHS ARE INDICATED ON THE GAS ISOMETRIC
	RISER DIAGRAM.

	E. OK

	F. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED. THE
	MANUF. SPECIFICATION SHEETS FOR ALL GAS APPLIANCES
	INCLUDING THE RTU ARE REQUIRED AND SHALL SHOW A LISTING
	AS WELL AS THE BTU LOAD OF THE APPLIANCE.

	G. N/A
	H. N/A

	I. EMERGENCY HOOD SHUT DOWN SHUT OFF
	VALVE TO BE BELOW CEILING. MANUAL SHUT
	OFF VALVE TO BE UPSTREAM. UNION TO BE
	DOWN STREAM OF MANUAL VALVE.
	****RESPONSE NOTED, BUT THE COMMENT IS NOT ADDRESSED.

	********NEW COMMENTS*********

	1B. SEDIMENT TRAPS REQUIRED BY SECTION 408.4 SHALL BE
	SHOWN ON THE GAS RISER DIAGRAM.

	2B. SHUT OFF VALVES SHALL BE PROVIDED FOR EACH GAS
	APPLIANCE. SECTION 409.5. PLEASE SHOW THE SHUT OFF
	VALVE FOR THE RTU UNIT. ALL SHUT OFF VALVES SHALL BE
	ACCESSIBLE PER SECTION 409.5.

	3B. SEE ATTACHED SHEET CONCERNING THE DESIGN
	PROFESSIONAL AND FS 553.80(2)(B). THIS IS GIVEN AS A
	NOTICE ONLY AT THIS TIME.

	WHEN RESUBMITTING PLANS PLEASE INDICATE
	THE REVISION & REMOVE & REPLACE ANY
	PAGES AS NECESSARY. A TRANSMITTAL LETTER
	LISTING THE ORIGINAL REVIEW COMMENT NUMBER,
	WITH A DESCRIPTION OF THE REVISION
	MADE, IDENTIFYING THE SHEET OR SPECIFICATION
	PAGE WHERE THE CHANGES CAN BE FOUND
	WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE ALL VOID
	SHEETS FROM ALL PLANS AND PLACE ONE SET OF THEM LOOSELY
	ON TOP OF THE COLLATED PLANS TO BE REVIEWED. THANK YOU
	FOR YOUR ANTICIPATED COOPERATION.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	G			GAS REVIEW
Rev No	1	Status	F	Date	2007-11-03			Cont ID
Sent By	kstevens			Date	2007-06-20	Time	14:48	Rev Time	0.00
Received By	kstevens			Date	2007-06-20	Time	14:48	Sent To

Notes

2007-11-03 14:50:22	DENIED
	REFERENCE: FBC-2004 FUEL GAS

	1. A SEPARATE GAS PERMIT IS REQUIRED. THE FOLLOWING
	INFORMATION IS REQUIRED FOR THE GAS PERMIT:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.

	B. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE IF BEING USED.

	C. TYPE OF GAS, (LP OR NATURAL).

	D. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).

	E. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.

	F. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2.

	G. CLEARLY SHOW THE LOCATION AND CAP-
	ACITY OF LP TANK(S), TYPE OF TANK (DOT
	OR ASME), THE DISTANCE OF THE TANK FROM
	THE BUILDING AND ADJACENT PROPERTY LINES
	THE DISTANCE OF THE TANK FROM ALL SOUR-
	CES OF IGNITION, OTHER CONTAINERS, BUILD
	INGS, AND THE LOCATION OF ANY BUILDING
	OPENINGS BELOW THE RELIEF VALVE OF THE
	TANK PER NFPA 58, TABLE 3-2.2.2.

	H. CLEARLY INDICATE ON THE PLAN IF THE
	LP TANK IS ABOVE OR BELOW GROUND, AND
	SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES
	PER NFPA 58. IF THE TANK
	IS BELOW GROUND THE CONTAINER SHALL BE
	SECURILY ANCHORED PER NFPA 58 SECTION
	3-2.2.7(H).

	I. EMERGENCY HOOD SHUT DOWN SHUT OFF
	VALVE TO BE BELOW CEILING. MANUAL SHUT
	OFF VALVE TO BE UPSTREAM. UNION TO BE
	DOWN STREAM OF MANUAL VALVE.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2007-09-14			Cont ID
Sent By	adarroug			Date	2007-09-14	Time	09:27	Rev Time	0.00
Received By	adarroug			Date	2007-09-14	Time	09:27	Sent To

Notes

2007-10-05 17:19:16	TO "COMM" BD#22
2007-09-14 09:27:40	WAITING FOR "COMM" BD

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2007-07-12			Cont ID
Sent By	mawillia			Date	2007-07-12	Time	08:45	Rev Time	0.00
Received By	mawillia			Date	2007-05-17	Time	15:52	Sent To

Notes

2007-06-06 15:21:40	TO "COMM" BD#55
2007-05-17 15:54:09	WAITING FOR "COMM" BD--RESTAURANT

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2007-11-05			Cont ID
Sent By	rregueir			Date	2007-11-05	Time	11:18	Rev Time	0.00
Received By	rregueir			Date	2007-11-05	Time	07:53	Sent To	PC

Notes

2007-11-05 11:18:01	REVIEW #: 2ND
	ACTION: DENIED

	FBC 2004 CODE FAMILY W/ 2005 AND 2006 SUPPLEMENTS FBC
	CH.1 AS AMENDED BY THE CITY OF WEST PALM BEACH

	THE FOLLOWING COMMENTS ARE NUMBERED TO CORRESPOND WITH
	PREVIOUS REVIEW COMMENTS AS WELL AS DESIGNER'S WRITTEN
	RESPONSES FOR THE PURPOSE OF CONTINUITY.

	NOTE: THERE WAS NO WRITTEN RESPONSE TO PREVIOUS
	MECHANICAL REVIEW COMMENTS IN THIS SUBMITTAL PACKAGE.
	PLANS WILL BE REVIEWED TO DETERMINE IF PREVIOUS
	COMMENTS WERE ADDRESSED.

	1. NOT ADDRESSED. INFORMATION IS STILL MISSING ON
	PLANS.

	2. NOT ADDRESSED.

	3. NO VENTILATION (OUTSIDE AIR) CALCULATIONS OR
	INFORMATION PROVIDED. OCCUPANCY AND OCCUPANT LOAD FOR
	PURPOSES OF VENTILATION SHALL BE DETERMINED IN
	ACCORDANCE WITH FBC,M TABLE 403.3 PROVIDE CALCULATIONS
	SHOWING OCCUPANCY, OCCUPANT LOAD, O.A. REQUIRED AND
	O.A. PROVIDED. ALSO, PROVIDE BATHROOM EXHAUST FAN
	INFORMATION ON EQUIPMENT SCHEDULE SHOWING MAKE/MODEL,
	CFM AND MEANS OF CONTROL. ALSO SHOW DISCHARGE LOCATION
	OF BATH EXHAUST IN ACCORDANCE WITH FBC,M 401.5. NOTE:
	BATH EXHAUST FAN IS NOT SHOWN ON ELECTRICAL PLANS. HOW
	WILL THIS FAN BE POWERED?

	4. AIR BALANCE SCHEDULE FOR THE SPACE HAS NOT BEEN
	PROVIDED. PLEASE READ PREVIOUS COMMENT AND PROVIDE ALL
	REQUESTED INFORMATION TO SHOW COMPLIANCE WITH THE CODE
	SECTIONS AS PREVIOUSLY REFERENCED. NOTE: IT IS
	PROHIBITED TO HAVE RETURN AIR IN THE KITCHEN FOR
	NON-DEDICATED KITCHEN HVAC SYSTEMS IN ACCORDANCE WITH
	FBC,M 407.1.

	5. NOT ADDRESSED. NO INFORMATION PROVIDED. SEE PREVIOUS
	REVIEW COMMENT.

	6. WITHOUT A WRITTEN RESPONSE, THE FOLLOWING IS NOTED
	BASED ON INFORMATION ON PLANS AND SUBMITTALS:
	A) PLAN INDICATES A/C IS NEW AND EXISTING. ONLY ONE
	SYSTEM IS SHOWN ON PLAN. ARE THERE TWO SYSTEMS? ONLY
	ONE IS LISTED ON EQUIPMENT SCHEDULE.
	B) FLOOR PLAN SHOWS A ?CU #5 ON ROOF.? IS THIS A
	ROOFTOP PACKAGE UNIT AS INDICATED BY EQUIPMENT SCHEDULE
	AND MANUAL J FORM OR A SPLIT SYSTEM WITH AHU AND CU? IS
	THIS THE NEW SYSTEM OR THE EXISTING SYSTEM?
	C) THE RTU LISTED ON PLAN DOES NOT MATCH THE RTU LISTED
	ON MANUAL J FORM.
	D) THE GAS RISER DIAGRAM SHOWS AN EXISTING 4 TON RTU ON
	ROOF. THIS DOES NOT MATCH ANY OF THE OTHER SUPPLIED
	INFORMATION. THERE IS ALSO A GAS LINE SHOWN GOING TO
	THE RTU FOR HEAT WHILE THE ELECTRICAL PLAN SHOWS A 5KW
	HEAT STRIP.
	E) ELECTRICAL PLAN SHOWS SERVICE FOR ONE AHU AND ONE CU
	FOR ONE SPLIT SYSTEM. WHERE IS THE 2ND SYSTEM ON
	ELECTRICAL PLANS? THE LETTER FROM A & J TECHNOLOGIES,
	INC. INDICATES THAT A NEW UNIT IS SIZED TO PROVIDE
	ADDITIONAL COOLING REQUIRED BY THE KITCHEN. IS THE ONE
	EXISTING SYSTEM BEING REPLACED OR IS THIS AN ADDITIONAL
	SYSTEM? IN ANY EVENT, THE ELECTRICAL SHOWS ONLY ONE
	SPLIT SYSTEM. THE ACTUAL NATURE OF THE WORK TO BE
	PERFORMED CAN NOT BE DETERMINED AT THIS TIME.
	F) THE LETTER INDICATES THAT A & J TECHNOLOGIES HAS
	DESIGNED THIS A/C SYSTEM. IN ORDER TO PERFORM DESIGN OF
	THIS COMMERCIAL SYSTEM, THEY ARE REQUIRED TO BE
	LICENSED AS AN ENGINEERING BUSINESS UNDER FS 471 OR AS
	A MECHANICAL CONTRACTOR UNDER FS 489. PROVIDE ALL
	RELEVANT LICENSE INFORMATION FOR THIS COMPANY. SEE FBC
	105.3.1.2(4).

	7. AIRFLOW ON SCHEDULE NOW SHOWS 1300 CFM, BUT WE STILL
	DON?T KNOW THE CFM OF THE 6 INCH DROP IN THE KITCHEN.
	THIS NEEDS TO BE ADJUSTED BASED ON WHAT EQUIPMENT IS
	ACTUALLY BEING USED AND WHAT IS REQUIRED BASED ON THE
	MANUAL J SUBMITTED.

	8. NOTE 9 HAS BEEN REMOVED. THERE IS NO LONGER A
	CONFLICT. HOWEVER, NOTE 4 NOW STATES 1\ INCH R-6 DUCT.
	GENERALLY 1 ? INCH IS REQUIRED TO ACHIEVE R-6. PLEASE
	CORRECT NOTE OR PROVIDE DUCT MANUFACTURER?S SUBMITTAL
	TO VERIFY THIS INFORMATION.

	9 AND 10. NO INFORMATION WAS PROVIDED REGARDING THE
	COMMERCIAL KITCHEN EXHAUST SYSTEM OTHER THAN A NOTE FOR
	CFM ON HE MANUAL J FORM. PROVIDE INFORMATION FOR A
	COMPLETE COMMERCIAL KITCHEN EXHAUST SYSTEM,
	DEMONSTRATING COMPLIANCE WITH FBC,M SECTIONS 505
	THROUGH 509.

	11. THIS COMMENT STILL STANDS AS SIGNIFICANT
	INFORMATION IS STILL MISSING.

	ENERGY CALCULATIONS: METHOD A COMPLIANCE FORM IS NOT
	AVAILABLE FOR THIS PROJECT AS THIS IS NOT A WHOLE
	BUILDING. SHOW COMPLIANCE WITH MINIMUM PRESCRIPTIVE
	REQUIREMENTS FOR ALL NEW COMPONENTS BEING INSTALLED IN
	ACCORDANCE WITH FBC 13-400.0.C.4.

	IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:
	RONALD J. REGUEIRO
	561.805.6719
	[email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2007-06-16			Cont ID
Sent By	rregueir			Date	2007-06-16	Time	11:45	Rev Time	0.00
Received By	rregueir			Date	2007-06-16	Time	10:11	Sent To

Notes

2007-06-16 11:44:25	------------------DENIED--------------------

	FBC 2004 CODE FAMILY W/ 2006 REVISIONS
	FBC CH.1 AS AMENDED BY THE CITY OF WEST PALM BEACH


	1. PLEASE SHOW SIZE OF OUTSIDE AIR DUCT FROM 12X12
	O.A.I. TO R/A PLENUM. ALSO, PLEASE SHOW CFM OF 6" DROP
	IN BACK OF SPACE. FBC 106.1.1.

	2. SUPPLY TRUNK LINE SHOWS ONE TRANSITION FROM 1/12 TO
	12/10. IS THE TRUNK LINE TO REMAIN THAT SIZE FOR THE
	REMAINING 3 DROPS? FBC 106.1.2.

	3.PLEASE SHOW VENTILATION CALCULATIONS WHICH
	DEMONSTRATE COMPLIANCE WITH FBC,M 403.3. ALSO, BATHROOM
	EXHAUST IS ALSO REQUIRED BY THIS SECTION. PLEASE SHOW
	MEANS OF EXHAUST, CFM AND DISCHARGE LOCATION.

	4. PLEASE SHOW AN AIR BALANCE SCHEDULE INCLUDING
	SUPPLY, RETURN, OUTSIDE AIR, BATHROOM EXHAUST, KITCHEN
	EXHAUST WITH MAKE-UP AIR TO SHOW PRESSURIZATION OF
	SPACE PER FBC 13-409.1.ABC.2 AND COMPLIANCE WITH
	KITCHEN SPACE REQUIREMENTS OF 13-409-1.ABC 3.6.1.

	5.PLEASE SHOW MEANS/LOCATION OF CONDENSATE DISPOSAL IN
	COMPLIANCE WITH FBC,M 307.2 (ALL SECTIONS) INCLUDING
	SECONDARY/AUXILIARY DRAIN PROTECTION PER 307.2.3.

	6. ELECTRICAL PLAN INDICATES A/C EQUIPMENT IS EXISTING,
	BUT SCOPE OF WORK AS DESCRIBED ON PERMIT APPLICATION
	STATES "SPACE IS CURRENTLY GUTTED."ALSO, HVAC NOTE #6
	SUGGESTS A/C EQUIPMENT IS NEW, NOT EXISTING. WHICH ONE
	IS CORRECT? FBC 106.1.1.

	7. EQUIPMENT SCHEDULE SHOWS INDOOR AIRFLOW AT 1000 CFM
	BUT FLOOR PLAN SHOWS 1300 CFM, NOT INCLUDING THE 6"
	DROP WHICH DOESN'T SHOW CFM. PLEASE SHOW CORRELATION
	BETWEEN SCHEDULE AND FLOOR PLAN.

	8. HVAC NOTE #4 IS IN CONFLICT WITH NOTE #9. PLEASE
	CLARIFY.

	9. SCOPE OF WORK ON PERMIT APPLICATION INDICATES GAS
	AND KITCHEN EQUIPMENT. PLEASE SHOW ALL VENTS AND
	KITCHEN EXHAUST PER FBC 106.3.5.1.4. ALSO, A COMMERCIAL
	KITCHEN GREASE EXHAUST VENTILATION SYSTEM W/ AUTOMATIC
	FIRE SUPPRESSION SYSTEM IS REQUIRED PER FBC,M 507.2.1
	AND 509.1.

	10. PLEASE SEE FBC,M 507.9 FOR CLEARANCE REQUIREMENTS
	RELATED TO TYPE I KITCHEN HOODS INCLUDING REQUIREMENTS
	FOR WALL SURFACES ADJASCENT TO THE HOOD AND COOKING
	EQUIPMENT.

	11. SIGNIFICANT INFORMATION IS MISSING FROM PLANS TO
	SHOW A CODE COMPLIANT BUILDING/SPACE AT THIS TIME.
	ADDITIONAL COMMENTS ARE POSSIBLE BASED ON THE
	ADDITIONAL INFORMATION WHEN IT IS PROVIDED.

	IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:
	RONALD J REGUEIRO
	561.805.6719
	[email protected]

Review Stop	P			PLUMBING
Rev No	2	Status	F	Date	2007-11-03			Cont ID
Sent By	kstevens			Date	2007-11-03	Time	16:21	Rev Time	0.00
Received By	kstevens			Date	2007-11-03	Time	16:21	Sent To

Notes

2007-11-03 17:07:29	DENIED
	REFERENCE: FBC-2004 PLUMBING
	FBC-2004 BUILDING
	FBC-2004 FUEL GAS
	FBC-2004 CHAPTER 1
	FBC-2004 CHAPTER 11
	FLORIDA ADMINISTRATIVE CODE
	FLORIDA STATUTES

	****FROM PREVIOUS REVIEW. THE COMMENT NUMBER SHALL
	REMAIN THE SAME AS 1ST REVIEW:

	1. PLANS SHALL BE ROUTED TO THE STATE OF FLORIDA, DEPT.
	OF BUSINESS REGULATION, (DBR), DIVISION OF HOTEL AND
	RESTAURANT FOOD SERVICE FOR REVIEW. A MINIMUM OF TWO
	STAMPED PLANS WITH "TWO PAGE WORKSHEETS" ATTATCHED TO
	STAMPED PAGE SHALL BE SUBMITTED FOR REVIEW TO CITY WPB.
	SECTION 102.2.1.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED.

	2. THE GREASE INTERCEPTOR SHALL BE SIZED BY
	ENVIRONMENTAL COMPLIANCE. PLEASE CONTACT RODNEY COMPO,
	(561) 822-2272,[email protected] OR CALVIN WILLIAMS,
	(561) 822-2284 [email protected]. THEIR FAX NUMBER IS
	(561) 822-2287. PLEASE INDICATE THEIR DETERMINATION
	WHEN RESUBMITTING. ARTICLE III SECTION 90-124. PLEASE
	SUBMIT A DETAIL FOR THE GREASE INTERCEPTOR. (SEE
	ATTACHED SHEET SHOWING WPB UTILITY STANDARD FOR
	INTERCEPTORS).
	****RESPONSE NOTED, BUT THE GREASE INTERCEPTOR IS STILL
	SHOWN ON THE PLANS. ALSO IF THE GREASE INTERCEPTOR IS
	TO BE WAIVED, THEN AS REQUIRED A SAMPLE POINT SHALL BE
	INSTALLED ON THE GREASE LINE PRIOR TO CONNECTING INTO
	THE SANITARY DRAIN AND THE GREASE INTERCEPTOR SHOULD BE
	DELETED FROM THE RISER DIAGRAM.

	3. ALL SHEETS. THE ADDRESS OF THE ARCHITECT OF RECORD
	DOES NOT REFLECT THE ADDRESS RECORDED ON THE STATE OF
	FLORIDA DBPR WEBSITE. (SEE ATTACHED SHEET). PLEASE
	UPDATE THE DBPR WEBSITE OR THE TITLE BLOCKS ON EACH
	SHEET SO THE ADDRESS CORRELATES. FAC 61G1-16.004(1) &
	FS 481-2055.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED ON ALL
	SHEETS WITH THE ARCHITECT FIRM TITLE BLOCK. ALL SHEETS
	SHALL SHOW THE CORRECT ADDRESS.

	4. OK
	5. OK

	6. INDICATE CODE REFERENCES THAT THE PLANS HAVE BEEN
	DESIGNED TO. FBC-2004 W/2006 AMENDMENTS MINIMUM.
	****RESPONSE NOTED, BUT THE CODE ADOPTED IS NOT 2007
	BUILDING CODE. PLEASE CORRECT CODE REFERENCE.

	7. SHT A-1 TOILET ROOM. THE TURNING AREA SHALL BE
	UNOBSTRUCTED AND THE TOILET SHALL NOT BE IN THE TURNING
	AREA. SECTION 11-4.22.3.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED. REMOVING
	THE TURNING AREA IS NOT A CORRECT RESPONSE TO SHOW
	COMPLIANCE. PLEASE SHOW THE REQUIRED TURNING AREA AND
	THE TOILET SHALL NOT BE IN THE TURNING AREA.

	8. SUBMIT A DETAIL FOR THE TOILET ROOM SHOWING
	COMPLIANCE WITH SECTIONS 11-4.16, 11-4.19 & 11-4.22
	WITH ALL SUBSECTIONS. THE DETAIL SHALL SHOW THE FLOOR
	PLAN AND ELEVATIONS WITH ALL REQUIRED MEASUREMENTS. THE
	W/C SHALL BE 18" OFF THE WALL TO THE CENTERLINE OF THE
	FIXTURE, AND THE LAV SHALL BE A MINIMUM 15" OFF THE
	WALL TO THE CENTERLINE OF THE FIXTURE. SEE FIGS 28 &
	29.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED. SHOW
	COMPLIANCE WITH THE FOLLOWING:
	___FOR THE W/C:
	A. 11-4.16.3 HEIGHT
	B. 11-4.16.4 GRAB BARS
	C. 11-4.16.5 FLUSH CONTROLS
	D. 11-4.16.6 DISPENSERS
	___FOR THE LAV:
	A. 11-4.19.2 HEIGHT & CLEARANCES
	B. 11-4.19.3 CLEAR FLOOR SPACE
	C. 11-4.19.4 EXPOSED PIPES & SURFACES
	D. 11-4.19.5 FAUCETS
	E. 11-4.19.6 MIRRORS

	9. SUBMIT A FINISH SCHEDULE FOR THE TOILET ROOM SHOWING
	COMPLIANCE WITH SECTIONS 1210.1 & 1210.2. WALLS WITHIN
	2 FEET OF THE WATER CLOSET SHALL BE A SMOOTH, HARD AND
	NONABSORBENT SURFACE.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED.

	10. SHT A-2 THE GREASE RISER DIAGRAM DOES NOT REFLECT
	THE FIXTURE LAYOUT ON THE FLOOR PLAN. PLEASE SHOW A
	PIPING LAYOUT ON THE FLOOR PLAN AND THE GREASE RISER
	ISOMETRIC DIAGRAM SHALL REFLECT THE PIPING LAYOUT.
	SECTION 106.1.1.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED.

	11. SHT A-2 SANITARY ISOMETRIC RISER DIAGRAM DOES NOT
	CONNECT TO THE BUILDING DRAIN. SHOW THE CONNECTION FOR
	THE BRANCH LINE TO THE BUILDING DRAIN . SECTION
	106.1.1.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED.

	12. SUBMIT A WATER RISER DIAGRAM. SHOW ALL PIPE SIZES,
	VALVES, AND WATER HAMMER ATTESTORS, (REQD BY SECTIONS
	604.9). SECTION 106.3.5.1.3(3)(8)(10)(13). ****RESPONSE
	NOTED, BUT COMMENT NOT ADDRESSED.

	13. SUBMIT A WATER HEATER DETAIL SHOWING COMPLIANCE
	WITH SECTIONS 503.1, 504.6.1 & 607.3.2 (THERMAL
	EXPANSION CONTROL).
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED. THE
	REQUIREMENT FOR SECTION 503.1 IS A SHUT OFF VALVE FOR
	WATER HEATER. THE VALVE AS SHOWN WILL SHUT OFF MORE
	THAN THE WATER HEATER. THE PLACE OF DISPOSAL FOR THE
	T&P VALVE DISCHARGE LINE IS NOT INDICATED, NOR IS THE
	EMERGENCY PAN DRAIN LINE TERMINATION POINT.

	14. AN RPZV BACKFLOW IS REQUIRED ON THE WATER SERVICE
	TO THE SPACE. SECTION 608.13.2. PLEASE INDICATE ON THE
	PLANS.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED. NO
	REFERENCE TO THE RPZV BACKFLOW IS FOUND ON SHT A-1.

	15. A SEPARATE GAS PERMIT IS REQUIRED. THE FOLLOWING
	INFORMATION IS REQUIRED FOR THE GAS PERMIT:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.
	****RESPONSE NOTED, BUT COMMENT NOT COMPLETLY
	ADDRESSED. LENGTHS OF PIPE NOT SHOWN.

	B. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE IF BEING USED. ****RESPONSE
	NOTED, BUT COMMENT NOT ADDRESSED. PIPE TYPE NOT
	INDICATED ON LEGEND.

	C. OK

	D. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).
	****RESPONSE NOTED, BUT THIS WILL BE VERIFIED WHEN ALL
	CUT SECTION LENGTHS ARE INDICATED ON THE GAS ISOMETRIC
	RISER DIAGRAM.

	E. OK

	F. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2.
	****RESPONSE NOTED, BUT COMMENT NOT ADDRESSED. THE
	MANUF. SPECIFICATION SHEETS FOR ALL GAS APPLIANCES
	INCLUDING THE RTU ARE REQUIRED AND SHALL SHOW A LISTING
	AS WELL AS THE BTU LOAD OF THE APPLIANCE.

	G. N/A
	H. N/A

	I. EMERGENCY HOOD SHUT DOWN SHUT OFF
	VALVE TO BE BELOW CEILING. MANUAL SHUT
	OFF VALVE TO BE UPSTREAM. UNION TO BE
	DOWN STREAM OF MANUAL VALVE.
	****RESPONSE NOTED, BUT THE COMMENT IS NOT ADDRESSED.

	********NEW COMMENTS*********

	1B. SEDIMENT TRAPS REQUIRED BY SECTION 408.4 SHALL BE
	SHOWN ON THE GAS RISER DIAGRAM.

	2B. SHUT OFF VALVES SHALL BE PROVIDED FOR EACH GAS
	APPLIANCE. SECTION 409.5. PLEASE SHOW THE SHUT OFF
	VALVE FOR THE RTU UNIT. ALL SHUT OFF VALVES SHALL BE
	ACCESSIBLE PER SECTION 409.5.

	3B. SEE ATTACHED SHEET CONCERNING THE DESIGN
	PROFESSIONAL AND FS 553.80(2)(B). THIS IS GIVEN AS A
	NOTICE ONLY AT THIS TIME.

	WHEN RESUBMITTING PLANS PLEASE INDICATE
	THE REVISION & REMOVE & REPLACE ANY
	PAGES AS NECESSARY. A TRANSMITTAL LETTER
	LISTING THE ORIGINAL REVIEW COMMENT NUMBER,
	WITH A DESCRIPTION OF THE REVISION
	MADE, IDENTIFYING THE SHEET OR SPECIFICATION
	PAGE WHERE THE CHANGES CAN BE FOUND
	WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE ALL VOID
	SHEETS FROM ALL PLANS AND PLACE ONE SET OF THEM LOOSELY
	ON TOP OF THE COLLATED PLANS TO BE REVIEWED. THANK YOU
	FOR YOUR ANTICIPATED COOPERATION.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2007-06-20			Cont ID
Sent By	kstevens			Date	2007-06-20	Time	06:38	Rev Time	0.00
Received By	kstevens			Date	2007-06-19	Time	12:46	Sent To

Notes

2007-06-20 07:23:18	DENIED
	REFERENCE: FBC-2004 PLUMBING
	FBC-2004 BUILDING
	FBC-2004 FUEL GAS
	FBC-2004 CHAPTER 1
	FBC-2004 CHAPTER 11
	FLORIDA ADMINISTRATIVE CODE
	FLORIDA STATUTES

	1. PLANS SHALL BE ROUTED TO THE STATE OF FLORIDA, DEPT.
	OF BUSINESS REGULATION, (DBR), DIVISION OF HOTEL AND
	RESTAURANT FOOD SERVICE FOR REVIEW. A MINIMUM OF TWO
	STAMPED PLANS WITH "TWO PAGE WORKSHEETS" ATTATCHED TO
	STAMPED PAGE SHALL BE SUBMITTED FOR REVIEW TO CITY WPB.
	SECTION 102.2.1.

	2. THE GREASE INTERCEPTOR SHALL BE SIZED BY
	ENVIRONMENTAL COMPLIANCE. PLEASE CONTACT RODNEY COMPO,
	(561) 822-2272,[email protected] OR CALVIN WILLIAMS,
	(561) 822-2284 [email protected]. THEIR FAX NUMBER IS
	(561) 822-2287. PLEASE INDICATE THEIR DETERMINATION
	WHEN RESUBMITTING. ARTICLE III SECTION 90-124. PLEASE
	SUBMIT A DETAIL FOR THE GREASE INTERCEPTOR. (SEE
	ATTACHED SHEET SHOWING WPB UTILITY STANDARD FOR
	INTERCEPTORS).

	3. ALL SHEETS. THE ADDRESS DOES NOT REFLECT THE ADDRESS
	RECORDED ON THE STATE OF FLORIDA DBPR WEBSITE. (SEE
	ATTACHED SHEET). PLEASE UPDATE THE DBPR WEBSITE OR THE
	TITLE BLOCKS ON EACH SHEET SO THE ADDRESS CORRELATES.
	FAC 61G1-16.004(1) & FS 481-2055.

	4. SHT A-1 EQUIPMENT SCHEDULE ITEM K11 NOT SHOWN ON THE
	FLOOR PLAN. PLEASE CLARIFY. SECTION 106.1.1.

	5. INDICATE THE OCCUPANCY LOAD AND SEATING ON THE
	PLANS. SECTIONS 1004.3 & 1004.7.

	6. INDICATE CODE REFERENCES THAT THE PLANS HAVE BEEN
	DESIGNED TO. FBC-2004 W/2006 AMENDMENTS MINIMUM.

	7. SHT A-1 TOILET ROOM. THE TURNING AREA SHALL BE
	UNOBSTRUCTED AND THE TOILET SHALL NOT BE IN THE TURNING
	AREA. SECTION 11-4.22.3.

	8. SUBMIT A DETAIL FOR THE TOILET ROOM SHOWING
	COMPLIANCE WITH SECTIONS 11-4.16, 11-4.19 & 11-4.22
	WITH ALL SUBSECTIONS. THE DETAIL SHALL SHOW THE FLOOR
	PLAN AND ELEVATIONS WITH ALL REQUIRED MEASUREMENTS. THE
	W/C SHALL BE 18" OFF THE WALL TO THE CENTERLINE OF THE
	FIXTURE, AND THE LAV SHALL BE A MINIMUM 15" OFF THE
	WALL TO THE CENTERLINE OF THE FIXTURE. SEE FIGS 28 &
	29.

	9. SUBMIT A FINISH SCHEDULE FOR THE TOILET ROOM SHOWING
	COMPLIANCE WITH SECTIONS 1210.1 & 1210.2. WALLS WITHIN
	2 FEET OF THE WATER CLOSET SHALL BE A SMOOTH, HARD AND
	NONABSORBENT SURFACE.

	10. SHT A-2 THE GREASE RISER DIAGRAM DOES NOT REFLECT
	THE FIXTURE LAYOUT ON THE FLOOR PLAN. PLEASE SHOW A
	PIPING LAYOUT ON THE FLOOR PLAN AND THE GREASE RISER
	ISOMETRIC DIAGRAM SHALL REFLECT THE PIPING LAYOUT.
	SECTION 106.1.1.

	11. SHT A-2 SANITARY ISOMETRIC RISER DIAGRAM DOES NOT
	CONNECT TO THE BUILDING DRAIN. SHOW THE CONNECTION FOR
	THE BRANCH LINE TO THE BUILDING DRAIN . SECTION
	106.1.1.

	12. SUBMIT A WATER RISER DIAGRAM. SHOW ALL PIPE SIZES,
	VALVES, AND WATER HAMMER ATTESTORS, (REQD BY SECTIONS
	604.9). SECTION 106.3.5.1.3(3)(8)(10)(13).

	13. SUBMIT A WATER HEATER DETAIL SHOWING COMPLIANCE
	WITH SECTIONS 503.1, 504.6.1 & 607.3.2 (THERMAL
	EXPANSION CONTROL).

	14. AN RPZV BACKFLOW IS REQUIRED ON THE WATER SERVICE
	TO THE SPACE. SECTION 608.13.2. PLEASE INDICATE ON THE
	PLANS.

	15. A SEPARATE GAS PERMIT IS REQUIRED. THE FOLLOWING
	INFORMATION IS REQUIRED FOR THE GAS PERMIT:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.

	B. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE IF BEING USED.

	C. TYPE OF GAS, (LP OR NATURAL).

	D. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).

	E. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.

	F. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2.

	G. CLEARLY SHOW THE LOCATION AND CAP-
	ACITY OF LP TANK(S), TYPE OF TANK (DOT
	OR ASME), THE DISTANCE OF THE TANK FROM
	THE BUILDING AND ADJACENT PROPERTY LINES
	THE DISTANCE OF THE TANK FROM ALL SOUR-
	CES OF IGNITION, OTHER CONTAINERS, BUILD
	INGS, AND THE LOCATION OF ANY BUILDING
	OPENINGS BELOW THE RELIEF VALVE OF THE
	TANK PER NFPA 58, TABLE 3-2.2.2.

	H. CLEARLY INDICATE ON THE PLAN IF THE
	LP TANK IS ABOVE OR BELOW GROUND, AND
	SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES
	PER NFPA 58. IF THE TANK
	IS BELOW GROUND THE CONTAINER SHALL BE
	SECURILY ANCHORED PER NFPA 58 SECTION
	3-2.2.7(H).

	I. EMERGENCY HOOD SHUT DOWN SHUT OFF
	VALVE TO BE BELOW CEILING. MANUAL SHUT
	OFF VALVE TO BE UPSTREAM. UNION TO BE
	DOWN STREAM OF MANUAL VALVE.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	Z			ZONING
Rev No	1	Status	N	Date	2007-06-11			Cont ID
Sent By	mflis			Date	2007-06-11	Time	16:25	Rev Time	0.00
Received By	mflis			Date	2007-06-11	Time	16:25	Sent To

Notes

2007-06-11 16:26:37	ZONING REVIEW: NOT REQUIRED

	* INTERIOR DEMOLITION ONLY
	* NO MODIFICATION TO EXTERIOR FACADE

	MATT FLIS - 822-1445