City of West Palm Beach eGovPlus

Plan Review Details - Permit 06090092

Plan Review Stops For Permit 06090092

Review Stop	AD			ADDRESSING
Rev No	1	Status	P	Date	2006-10-16			Cont ID
Sent By	rbrown			Date	2006-10-16	Time	18:08	Rev Time	0.00
Received By	rbrown			Date	2006-09-05	Time	13:02	Sent To

Notes

2006-10-16 18:10:31	ADDRESS CHANGED TO 330 CLEMATIS ST # 1-G (WAS 330
	CLEMATIS ST) BY LILI ON 9/6/06

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2006-11-07			Cont ID
Sent By	shill			Date	2006-11-07	Time	09:23	Rev Time	0.00
Received By	shill			Date	2006-11-07	Time	09:23	Sent To

Notes

2006-11-07 09:24:18	SAMANTHA HILL, BUILDING PLANS EXAMINER
	561-805-6724 [email protected]

	FBCFLORIDA BUILDING CODE 2004
	FBC RFLORIDA BUILDING CODE 2004 RESIDENTIAL FBC EB
	FLORIDA BUILDING CODE 2004 EXISTING BUILDING CODE FBC*
	CITY OF WEST PALM BEACH AMENDMENTS TO THE FBC2004


	1.)A NOTICE OF COMMENCEMENT MUST BE
	FILED WITH THE CLERK OF COURTS,
	FS713.13.

	2.)ADDRESSED.

	3.)DELCARE LEVEL OF ALTERATION FBC EB
	3 AND INCLUDE FBC EB IN GOVERNING CODE.

	I THINK THAT THERE MAY HAVE BEEN A MISUNDERSTANDING.
	THE REFERENCE IS FOR FBC EB CHAPTER 3, WHICH SPECIFIES
	HOW TO DETERMINE THE LEVEL OF ALTERATION.ARCHITECT
	HAS DECLARED A LEVEL 3, WHICH IS OVER 50% RENOVATION.
	IF THIS IS A LEVEL 3 ALTERATION, SHOW COMPLIANCE WITH
	ALL REQUIREMENTS FOR THE EXISTING BUILDING ON THE PLAN.
	IF NOT, REVISE THE NOTE.

	4.-5.)ADDRESSED.

	6.)SHOW MANEUVERING CLEARANCE, PULL
	SIDE, FOR DOORS 03, 04, 05 FBC11-4.13.6,
	FIGURE 11-25.

	THIS WAS ADDRESSED FOR DOOR 3 ONLY.PLEASE ADDRESS FOR
	THE OTHER TWO DOORS OR CALL ME TO DISCUSS.

	7-9.)ADDRESSED.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2006-10-05			Cont ID
Sent By	shill			Date	2006-10-05	Time	13:49	Rev Time	0.00
Received By	shill			Date	2006-10-05	Time	13:49	Sent To

Notes

2006-10-05 00:00:00	SAMANTHA HILL, BUILDING PLANS EXAMINER
	561-805-6724 [email protected]

	FBCFLORIDA BUILDING CODE 2004
	FBC RFLORIDA BUILDING CODE 2004
	RESIDENTIAL
	FBC EBFLORIDA BUILDING CODE 2004
	EXISTING BUILDING CODE
	FBC*CITY OF WEST PALM BEACH
	AMENDMENTS TO THE FBC2004


	1.)A NOTICE OF COMMENCEMENT MUST BE
	FILED WITH THE CLERK OF COURTS,
	FS713.13.

	2.)SHEET A.0 DECLARES A2 OCCUPANCY,
	EXIT REQUIREMENTS ARE FOR MERCANTILE,
	PLEASE REVISE.

	3.)DELCARE LEVEL OF ALTERATION FBC EB
	3 AND INCLUDE FBC EB IN GOVERNING CODE.

	4.)WHAT IS THE CURRENT OCCUPANCY?IF
	THIS IS A CHANGE OF OCCUPANCY, INDICATE
	ON THE PLAN.

	5.)PROVIDE ADDITIONAL INFORMATION IN
	REGARDS TO THE EXISTING BUILDING; TOTAL
	SF AREA, HEIGHT.CEILING HEIGHT IS
	SHOWN BUT PLEASE PROVIDE BUILDING
	HEIGHT.

	6.)SHOW MANEUVERING CLEARANCE, PULL
	SIDE, FOR DOORS 03, 04, 05 FBC11-4.13.6,
	FIGURE 11-25.

	7.)SEE FBC11-7.2, SERVICE COUNTER
	REQUIREMENT OF 36IN HEIGHT FOR A MINIMUM
	LENGTH OF 36IN, 40IN HEIGHT SHOWN.

	8.)THE PLAN STATES THAT SF AREA IS
	2853, ENERGY CALCS STATE 2250.REVISE.

	9.)THE ENERGY CALCS DECLARE PALM BEACH
	COUNTY AS JURISDICTION; CORRECT
	JURISDICTION IS CITY OF WEST PALM BEACH,
	604700.

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2006-10-28			Cont ID
Sent By	dpalmer			Date	2006-10-28	Time	16:40	Rev Time	0.00
Received By	dpalmer			Date	2006-10-28	Time	15:37	Sent To

Notes

2006-10-28 16:40:03	* UNSAT 2ND REVIEW *

	** PLEASE SEE SOMEITEMS FROM PREVIOUS REVIEW AND
	QUESTIONS ON REPSONSE LTR AND NEW NOTE FOR CHANGE IN
	RISER.

	** PLEASE KNOW, AS RESUBMITTED PACKAGE WAS PICKED UP
	FOR REVIEW, THE ORIGINAL PERMIT APPLICATION FROM THE
	CONTRACTOR WAS NOT LCOATED IN WITH ALL OTHER PAPERWORK?
	CALLED AND LEFT A MESSAGE ON BILL RIELLY'S VM TO DROP
	OFF PERMIT APPLCATION.

	1) NOTE: OK, REVISED RISER.

	2) NOTE: OK REVISED RISER.

	3) NOTE: OK.

	4) NOTE: OK, REVISED RISER.

	5) NOTE: OK.

	6) NOTE: OK, HOWEVER LOAD CALCULATIONS DO INDICATE HOW
	THE LOADS FOR SHOW WINDOW CIRCUITS WERE DERIVED. PLEASE
	SEE 220.12A

	PREVIOUS REVIEW NOTE
	PLEASE INDICATE NEW OR EXISTING RECEPT'S ABOVE
	WINDOW'S. (EVERY 12' OR FRACTION THEREOF)
	210.62,220.12

	7) NOTE:OK, HOWEVER RESPONSE MENTIONS EXISTING PANEL
	BEING REPLACED WITH A NEW 150A MAIN DISCONNETC HOWEVER
	RISER DOES NOT SHOW THIS? SHOWS AND INDICATES EQUIPMENT
	BEING REMOVED ONLY??

	8) NOTE: OK.

	9) NOTE: NO, PLEASE SEE THE TC SYSTEM IS BEING SHOWN
	HOWEVER THE OVER RIDE DEVICE(S) LOCATED AT THE POINT OF
	ENTRANCE INTO SPACE AND OVER RIDE DEVICE(S) LOCATED AT
	LOCATIONS WHERE THE OCCUPANT CAN VISUALLY SEE ALL
	LIGHTING BEING CONTROLLED. PLEASE SEE SEPARATE SPACES
	WITH FLR TO CEILING HEIGHT PARTITIONS REQUIRED SEPARATE
	CONTROL.
	PLEASE SEE "ST" DEVICE AS SHOWN FOR SOME RMS MENTIONS
	UP TO 12HRS, HOWEVER PLEASE SEE CODE ONLY PERMITS A MAX
	OF 4HRS ON TIMER TYPE DEVICES. ON OCC SENSOR TYPE
	DEVICES IT IS 30 MINS.
	PLEASE SEE SCHEDULE "A" WAS SUBMITTED WHICH DOES SEEM
	TO FIT FOR SCOPE OF WORK. PLEASE SEE "B" OR "C". PLEASE
	ALSO SEE PREVIOUS NOTE WITH RESPECT TO PERFORMANCE
	CALCULATIONS PER 13-415.2.
	13-101.1.3

	PREVIOUS REVIEW NOTE
	PLEASE SEE FBC CHAPTER 13 FOR
	AUTOMATED LIGHTING CONTROLLED REQUIRED.
	PLEASE SEE 13-415.1.ABC.1.1, .1.2 AND
	.1.3.
	PLEASE PROVIDE SCHEDULING, TIMERS,
	OVER-RIDES AND TYPES OF DEVICES. PLEASE
	SHOW ALL CONTROL/OVER RIDE LOCATIONS.
	PLEASE SEE ALL SEPARATE SPACES WITH FLR
	TO CEILING HEIGHT PARTITIONS, WITH
	CONTROLS.
	PLEASE PROVIDE ENERGY CALCULATIONS AS
	REQUIRED 13-415.1.AB.1, 13-415.2.ABC.1,
	415.2.C.



	10) NOTE: OK.

	11) NOTE:NO, PLEASE SEE RESPONSE SPEAKS OF A/C
	EQUIPMENT. THIS NOT WAS FOR THE "AIC" RATINGS FOR NEW
	EQUIPMENT/MAINS/PANELS ECT. PLEASE SEE PANELS ARE NOTED
	AND SHOWN AT 22K. PLEASE INDICATE FUSE RATING(S).
	110.9,240.12

	PREVIOUS REVIEW NOTE
	PLEASE INDICATE THE AIC
	RATINGS FOR ALL NEW SERVICE
	MAINS/EQUIPMENT.
	110.9

	NEW NOTE

	12) NOTE: PLEASE INDICATE VOLTAGE DROP FOR FEEDERS FROM
	MAIN ELECTRICAL ROOM TO NEW PANEL LOCATIONS.
	PLEASE SEE 13-413.1.ABC.1.1



	IMPORTANT
	ONCE ALL REVIEWS ARE DONE AND PLANS ARE
	PICKED UP FOR CORRECTIONS, PLEASE BE
	SURE TO COMPLETELY REMOVE ALL OLD/VOIDED
	SHEETS AND ONLY INSERT NEW REVISED
	SHEETS INTO TWO COMPLETE SETS FOR REVIEW
	AND STAMPING. DO NOT LEAVE ANY
	OLD/VOIDED SHEETS IN SETS.
	PLEASE KNOW ONLY ONE SET OF THE
	OLD/VOIDED SHEETS SHOULD BE SUBMITTED
	FOR REFERENCE.
	THIS WILL HELP IN THE REVIEW PROCESS AND
	AVOID ANY DELAYS.

	PLEASE SUBMIT THE ABOVE INFORMATION FOR
	REVIEW. IF THERE ARE ANY QUESTIONS,
	PLEASE DO NOT HESITATE TO CALL.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW
	CONSTRUCTION SERVICES DEPT.
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2006-09-19			Cont ID
Sent By	dpalmer			Date	2006-09-19	Time	17:54	Rev Time	0.00
Received By	dpalmer			Date	2006-09-19	Time	14:03	Sent To

Notes

2006-09-19 00:00:00	* UNSAT *

	1) NOTE: PLEASE SEE SERVICE IS BEING
	SHOWN TO A 350A CAPABILITY , HOWEVER
	RISER SHOWS A 200A METER CAN BEING
	TAPPED.
	PLEASE SEE NOTES ON LOAD CALCS, AS LOADS
	EXCEED RATINGS OF EQUIPMENT AS SHOWN.
	240.4,310.16,230.70 ETC

	2) NOTE: PLEASE INCLUDE CONDUCTORS FROM
	METER TO GUTTER ANF FROM GUUTER TO NEW
	MAIN.
	240.310.16 ETC

	3) NOTE: PLEASE SHOW LOAD ON EXISTING
	GUTEER, SIZE AND NEW LOADS BEIGN ADDED.
	220, 215. ETC.
	FBC 106.1.2 ADMIN SECT.

	4) NOTE: PLEASE SEE LOAD CALCS MENTIONS
	TWO PANEL "B" 'S?
	PLEASE CLARIFY.
	106.1.2 FBC.

	5) NOTE: PLEASE INDICATE NEW OR EXISTING
	SIGN CIRCUIT(S) PER 600.5

	6) NOTE: PLEASE INDICATE NEW OR EXISTIGN
	RECEPTS ABOVE WINDOWS. (EVERY 12' OR
	FRACTION THEROF.
	210.62, 220.12

	7) NOTE: PLEASE SEE THIS SERVICE IS
	BEING SHOWN FOR ONE TENANT, YET IT IS
	ALSO BEING SHOWN FOR FEEDING
	"COURTYARD"??
	PLEASE VERIFY AS THE CODE DOES NOT
	PERMIT COMMON AREA LIGHTING ETC BEING
	CONTROLLED OR FED FROM A TENANT
	OCCUPANCY.
	210.25, 240.24

	8) NOTE: PLEASE CLARIFY SHUNT BRKR FOR
	ANY HOOD POWER/ LTS. NFPA-96

	9) NOTE: PLEASE SEE FBC CHAPTER 13 FOR
	AUTOMATED LIGHTING CONTROLLED REQUIRED.
	PLEASE SEE 13-415.1.ABC.1.1, .1.2 AND
	.1.3.
	PLEASE PROVIDE SCHEDULING, TIMERS,
	OVER-RIDES AND TYPES OF DEVICES. PLEASE
	SHOW ALL CONTROL/OVER RIDE LOCATIONS.
	PLEASE SEE ALL SEPARATE SPACES WITH FLR
	TO CEILING HEIGHT PARTITIONS, WITH
	CONTROLS.
	PLEASE PROVIDE ENERGY CALCULATIONS AS
	REQUIRED 13-415.1.AB.1, 13-415.2.ABC.1,
	415.2.C.

	PLEASE SEE THERE ARE SWITCHES BEING
	SHOWN ON PLANS WHICH DO NOT INDICATE
	CONTROL OF ANY PARTICULAR ITEM.?

	10) NOTE: PLEASE SHOW NEW OR EXISTING
	GFI RECEPT FOR ROOF TOP EQUIPMENT PER 210.8,210.63

	11) NOTE: PLEASE INDICATE THE AIC
	RATINGS FOR ALL NEW SERVICE
	MAINS/EQUIPMENT.
	110.9

	IMPORTANT
	ONCE ALL REVIEWS ARE DONE AND PLANS ARE
	PICKED UP FOR CORRECTIONS, PLEASE BE
	SURE TO COMPLETELY REMOVE ALL OLD/VOIDED
	SHEETS AND ONLY INSERT NEW REVISED
	SHEETS INTO TWO COMPLETE SETS FOR REVIEW
	AND STAMPING. DO NOT LEAVE ANY
	OLD/VOIDED SHEETS IN SETS.
	PLEASE KNOW ONLY ONE SET OF THE
	OLD/VOIDED SHEETS SHOULD BE SUBMITTED
	FOR REFERENCE.
	THIS WILL HELP IN THE REVIEW PROCESS AND
	AVOID ANY DELAYS.

	PLEASE SUBMIT THE ABOVE INFORMATION FOR
	REVIEW. IF THERE ARE ANY QUESTIONS,
	PLEASE DO NOT HESITATE TO CALL.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW
	CONSTRUCTION SERVICES DEPT.
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	2	Status	F	Date	2006-11-13			Cont ID
Sent By	mawillia			Date	2006-11-13	Time	16:00	Rev Time	0.00
Received By	mawillia			Date	2006-11-13	Time	15:59	Sent To

Notes

2006-11-13 16:18:41	***DENIED***



	PLEASE ACKNOWLEDGE COMMENTS FROM PREVIOUS FIRE PLAN
	REVIEW (10/12/2006) BY SHOWING ON THE PLANS HOW EACH
	ITEM WAS ADDRESSED.








	CAPT. MICHAEL A. WILLIAMS
	FIRE PLAN REVIEW
	561-805-6722

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2006-10-12			Cont ID
Sent By	mawillia			Date	2006-10-12	Time	10:20	Rev Time	0.00
Received By	mawillia			Date	2006-10-12	Time	10:20	Sent To

Notes

2006-10-12 11:45:03	***DENIED***




	1.)CONSTRUCTION, ALTERATION, ANDDEMOLITION
	OPERATIONS SHALL COMPLY WITH NFPA 241.

	2.)DEMOLITION OPERATIONS INVOLVING THE USE OF CUTTING
	AND WELDING SHALL BE DONE IN ACCORDANCE WITH NFPA 51B.

	3.)CONSTRUCTION AND/OR DEMOLITION OPERATIONS SHALL
	NOT INTERFERE OR HINDER EMERGENCY ACCESS TO THE SAID
	PROPERTY OR VICINITY THEREOF (INCLUDING FIRE LANES).

	4.)THE SCOPE OF THE INTERIOR BUILDOUT REQUIRING
	MODIFICATION OF THE FIRE ALARM OR FIRE SPRINKLER
	SYSTEM, SEPARATE PERMIT AND PLANS ARE REQUIRED.

	5.)INTERIOR FINISH FOR WALLS AND CEILINGS IN EXITS
	AND EXIT CORRIDORS SHALL BE CLASS "A" OR CLASS "B".

	6.)ON THE APPROPIATE EXTERIOR ELEVATION, SHOW/DISPLAY
	THE ADDRESS FOR THIS STRUCTURE.AS PER WEST PALM BEACH
	CODE, THE CHARACTERS (NUMBERS AND/OR LETTERS) SHALL BE
	NO LESS THAN 6" IN HEIGHT AND 1" IN WIDTH CONTRASTING
	WITH THE BACKGROUND.IF USED, HURRICANE SHUTTERS SHALL
	NOT COVER OR CONCEAL ADDRESS.

	7.)ADDITIONAL MECHANICAL PERMITS AND PLANS ARE
	REQUIRED FOR HOOD/SUPPRESSION SYSTEM(S).

	8.)ON SHEET M-3 HOOD SYSTEM NOTE #1, REFERENCES SHALL
	BE MADE TO NFPA 96, 2004 EDITION.

	9.)AS PER WPBFR, DUCT SMOKE DETECTORS SHALL INITIATE
	A GENERAL FIRE ALARM.




	CAPT. MICHAEL A. WILLIAMS
	FIRE PLAN REVIEW
	561-805-6722

Review Stop	G			GAS REVIEW
Rev No	2	Status	F	Date	2006-11-16			Cont ID
Sent By	kstevens			Date	2006-11-27	Time	17:42	Rev Time	0.00
Received By	kstevens			Date	2006-11-16	Time	17:42	Sent To

Notes

2006-11-27 17:44:01	DENIED
	REFERENCE: FBC-2004 FUEL GAS

	FROM PREVIOUS REVIEW

	1. SHTS A-6 & P-1. SHT A-6 INDICATES A
	NEW OVEN, AND SHT P-1 INDICATES A FRYER
	AND THE OVEN AS RECONNECTING (GAS SIZE
	AND CAPACITY SAME EXISTING). A GAS
	PERMIT WILL BE REQUIRED AND THE
	FOLLOWING INFORMATION WILL BE REQUIRED
	TO VERIFY COMPLIANCE WITH THE GAS CODE:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.
	****RESPONSE NOTED. THE CORRESPONDING LENGTH FROM "B"
	TO "D" IS NOT INDICATED

	B. OK
	C. OK
	D. OK

	E. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).
	****RESPONSE NOTED. THE DISTANCE SHOWN IS NOT CORRECT.
	ADDING WHAT IS SHOWN IS MINIMUM 68' FROM "F" TO "C",
	AND 64' FROM "F" TO "A" BUT THE SECTION BETWEEN "B"

	F. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.
	****RESPONSE NOTED. FLORIDA PUBLIC UTILITIES PROVIDES
	2LB OR .5 LB WITH A .5 INCHWC PRESSURE DROP. FBC-2004
	FUEL GAS TABLE 402.4(2). INDICATE THE PRESSURE AS .5
	PSI, NOT 1 PSI OR LESS.

	G. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2. (FOR
	ALL NEW EQUIPMENT).
	****RESPONSE NOTED. MANUF. SHEETS NOT SUBMITTED AND ARE
	REQUIRED FOR PLAN REVIEW.

	H. OK

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731

Review Stop	G			GAS REVIEW
Rev No	1	Status	F	Date	2006-09-29			Cont ID
Sent By	kstevens			Date	2006-09-29	Time	08:38	Rev Time	0.00
Received By	kstevens			Date	2006-09-29	Time	08:38	Sent To

Notes

2006-09-29 00:00:00	DENIED
	REFERENCE: FBC-2004 FUEL GAS

	1. SHTS A-6 & P-1. SHT A-6 INDICATES A
	NEW OVEN, AND SHT P-1 INDICATES A FRYER
	AND THE OVEN AS RECONNECTING (GAS SIZE
	AND CAPACITY SAME EXISTING). A GAS
	PERMIT WILL BE REQUIRED AND THE
	FOLLOWING INFORMATION WILL BE REQUIRED
	TO VERIFY COMPLIANCE WITH THE GAS CODE:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.

	B. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE IF BEING USED.

	C. TYPE OF GAS, (LP OR NATURAL).

	D. BTU LOAD OF EACH APPLIANCE AND THE
	TOTAL BTU LOAD ON THE SYSTEM. REFER TO
	THE FBC-2004 FUEL GAS CODE SECS. 401.8
	THRU 402.6.1 AND TABLES 402.4(1) THRU
	402.4(33).

	E. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).

	F. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.

	G. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2. (FOR
	ALL NEW EQUIPMENT).

	H. EMERGENCY HOOD SHUT DOWN SHUT OFF
	VALVE TO BE BELOW CEILING. MANUAL SHUT
	OFF VALVE TO BE UPSTREAM. UNION TO BE
	DOWN STREAM OF MANUAL VALVE. (INDICATED
	AS EXISTING RELOCATING).

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2006-10-25			Cont ID
Sent By	adarroug			Date	2006-10-25	Time	08:56	Rev Time	0.00
Received By	adarroug			Date	2006-10-25	Time	08:56	Sent To

Notes

2006-10-26 11:41:09	TO "COMM" BD#14
2006-10-25 08:57:03	WAITING FOR "COMM" BD

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2006-10-16			Cont ID
Sent By	pkrauss			Date	2006-10-16	Time	10:20	Rev Time	0.00
Received By	pkrauss			Date	2006-09-08	Time	13:24	Sent To

Notes

2006-09-13 00:00:00	TO "COMM" BD#55
2006-09-08 00:00:00	WAITING FOR "COMM" BD

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2006-11-01			Cont ID
Sent By	pkrauss			Date	2006-10-31	Time	14:58	Rev Time	0.00
Received By	pkrauss			Date	2006-10-31	Time	12:36	Sent To

Notes

2006-10-31 15:27:24
	COMMENTS FROM REVIEW DATED 10-13-06:

	COMMENT 1, 2 ,3

	COMMENT 4: EF-2 TERMINATION TO THE ROOF IS NOT
	INDICATED ON PLAN SHEET M-1.2.THIS WAS NOT ADDRESSED.
	REFERENCED PLAN SHEET WAS REMOVED FROM THE RESUBMITTED
	PLANS.PLEASE PROVIDE DETAIL OF EQUIPMENT LOCATED ON
	THE ROOF.PROVIDE DETAIL OF REQUIRED CLEARANCES FROM
	ROOF SURFACE, FRESH AIR INTAKE IN RELATION TO EXHAUST
	TERMINATIONS, AS WELL AS CLEARANCES FOR THE GREASE DUCT
	TERMINATION TO PROPERTY LINES, CONTINGUOUS BUILDINGS
	ETC.2004 FMC 506.3.12.3.

	COMMENT 5 WAS NOT ADDRESSED.PLAN SHEET M-1 INDICATES
	EF-2 (WHICH THE LOCATION OR TERMINATION IS NOT
	INDICATED ON THE PLAN). IS THIS A GRILLE AT THE
	CEILING?A HOOD IS NOT SHOWN OVER THE OVEN.PLEASE
	INDICATE WHAT TYPE OF "OVEN" THIS IS.PLEASE
	REFERENCE 2004 FMC 507.2.1, TYPE I HOOD SHALL BE
	INSTALLED WHERE COOKING APPLIANCES PRODUCE GREASE OR
	SMOKE, SUCH AS OCCURS WITH GRIDDLES, FRYERS, BOILERS,
	OVENS, RANGES, AND WOK RANGES.A TYPE II HOOD IS SHALL
	BE INSTALLED WHERE COOKING OR DISHWASHING APPLIANCES
	THAT PRODUCE HEAT OR STEAM AND DO NOT PRODUCE GREASE OR
	SMOKE, SUCH AS STEAMERS, KETTLES, PASTA COOKERS &
	DISHWASHING MACHINES.PLEASE CLARIFY.PLEASE PROVIDE
	MANUFACTURER'S SUBMITTAL FOR THE OVEN.

	COMMENT6 WAS NOT ADDRESSED.(PLAN SHEET M-1.2 WAS
	REMOVED FROM SUBMITTAL SET)PLAN SHEET M-1.2 APPEARS
	TO HAVE A WALL THAT TERMINATES ABOVE THE ROOF THAT
	SEPARATES RTU-1 & EF-1. PER 2004 FMC 306.5, ACCESS
	SHALL NOT REQUIRE CLIMBING OVER OBSTRUCTIONS GREATER
	THAN 30 INCHES.PLEASE NOTE, SHOULD ROOF HAVE A SLOPE
	GREATER THAN 4/14 PITCH SHOW COMPLIANCE WITH 306.5
	ITEMS 1 THROUGH 7.

	COMMENT 7 WAS NOT ADDRESSED.PLEASE INDICATE ACCESS TO
	ROOF.

	COMMENT8 WAS NOT ADDRESSED.PLEASE CLARIFY WHAT
	EQUIPMENTTHE20"X48" RETURN AIR DUCT & 20"X32"
	SUPPLY DUCT TERMINATING ON THE ROOF GO TO (RTU-1?)

	COMMENT 9 WAS NOT ADDRESSED.ADDITIONAL PERMITS
	REQUIRED FOR HOOD, FIRE SUPPRESSION, & WALK-IN COOLER.
	PLEASE PROVIDE PLANS AND MANUFACTURER'S SUBMITTAL DATA
	WITH PERMIT APPLICATION.

	IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT PATTY KRAUSS
	AT (561)805-6719 OR E-MAIL [email protected].




	PLEASE NOTE, FAN SCHEDULE ON PLAN SHEET M-1 SHOWS EF-1
	AS A COOKING LINE HOOD FAN BUT THE PLAN INDICATES EF-1
	IN THE RESTROOM

	PLEASE NOTE, GREASE DUCT ENCLOSURE OR SHAFT SHALL NOT
	ENCLOSE ANY OTHER DUCT SYSTEMS PER NFPA 96-01 SECTION
	7.7.5.2.

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2006-10-13			Cont ID
Sent By	pkrauss			Date	2006-10-13	Time	07:45	Rev Time	0.00
Received By	pkrauss			Date	2006-10-12	Time	15:32	Sent To

Notes

2006-10-13 07:57:06	DENIED:
	PLEASE CLARIFY THE FOLLOWING:
	1.PLAN SHEET A-1 INDICATES WEST WALL IS INDICATED AS
	A EXISTING TENANT DEMISING WALL.IS THIS AN EXTERIOR
	WALL OR IS THIS INTERIOR TO THE TENANT SPACE.PLEASE
	CLARIFY IF THIS WILL BE SEPARATED OR PROTECTED BY AN
	ENCLOSURE OR SHAFT?

	2.PLAN SHEET M-1 DUCT MISSING FIRE DAMPER FROM
	20"X48" R/A DUCT PENETRATING TENANT DEMISING WALL.

	3.PLEASE PROVIDE CLEARANCES FROM THE GREASE DUCT TO
	COMBUSTIBLES.SHOW COMPLIANCE WITH 2004 FMC 506.3.6.

	4.PLAN SHEET M-1 INDICATES EF-2 SERVES A COOK LINE
	HOOD TERMINATING ON THE ROOF.THIS IS NOT SHOWN ON
	PLAN SHEET M-1.2.

	5.PLEASE PROVIDE THE FOLLOWING INFORMATION FOR THE
	HOOD & GREASE DUCT:
	A) TYPE I OR TYPE II HOOD
	B) INDICATE HOOD & DUCT MATERIAL AND GAUGE 2004
	FMC 507.4, 507.5, 506.3.1.1 & 506.4.
	C) INDCIATE DUCT SIZE AND LAYOUT
	D) AIR VELOCITY THROUGH THE GREASE DUCT SHALL
	COMPLY WITH 2004 FMC 506.3.4

	6.PLAN SHEET M-1.2 APPEARS TO HAVE A WALL THAT
	TERMINATES ABOVE THE ROOF THAT SEPARATES RTU-1 & EF-1.
	PER 2004 FMC 306.5, ACCESS SHALL NOT REQUIRE CLIMBING
	OVER OBSTRUCTIONS GREATER THAN 30 INCHES.PLEASE NOTE,
	SHOULD ROOF HAVE A SLOPE GREATER THAN 4/14 PITCH SHOW
	COMPLIANCE WITH 306.5 ITEMS 1 THROUGH 7.

	7.PLEASE INDICATE ACCESS TO ROOF.

	8.PLEASE CLARIFY WHAT EQUIPMENTTHE20"X48" RETURN
	AIR DUCT & 20"X32" SUPPLY DUCT TERMINATING ON THE ROOF
	GO TO (RTU-1?)

	9.ADDITIONAL PERMITS REQUIRED FOR HOOD, FIRE
	SUPPRESSION, & WALK-IN COOLER.PLEASE PROVIDE PLANS
	AND MANUFACTURER'S SUBMITTAL DATA WITH PERMIT
	APPLICATION.

	IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT PATTY KRAUSS
	AT (561)805-6719 OR E-MAIL [email protected].

Review Stop	P			PLUMBING
Rev No	2	Status	F	Date	2006-11-16			Cont ID
Sent By	kstevens			Date	2006-11-16	Time	16:52	Rev Time	0.00
Received By	kstevens			Date	2006-11-16	Time	16:52	Sent To

Notes

2006-11-17 06:45:28	DENIED
	REFERENCE: FBC-2004 PLUMBING
	FBC-2004 FUEL GAS
	FBC-2004 CHAPTER 1
	FBC-2004 CHAPTER 11
	FLORIDA ADMINISTRATIVE CODE
	FLORIDA STATUES

	*****FROM 1ST REVIEW*****

	1. ALL SHEETS. THE ARCHITECTS TITLE
	BLOCK DOES NOT REFLECT THE ADDRESS FOUND
	ON THE DBPR WEBSITE. FAC 61G1-16.004(1)
	AND FS 481.2055. (SEE ATTACHED SHEET). ****RESPONSE
	NOTED. SUBMIT A LETTER FROM DBPR INDICATING APPROVAL OF
	THIS TEMPORY ARRANGEMENT. I DO NOT HAVE THE AUTHORITY
	TO WAIVE THIS REQUIREMENT OF THE FLORIDA ADMINISTRATIVE
	CODE/FLORIDA STATUTES.

	2. ROUTE PLANS TO DBPR HOTEL AND
	RESTURANT DIVISION FOR REVIEW. MINIMUM 2
	SETS OF STAMPED PLANS WITH THE TWO PAGE "WORKSHEETS"
	REQUIRED FOR REVIEW.
	SECTION 102.2.1.
	****RESPONSE NOTED. THIS IS REQUIRED FOR THE PLAN
	REVIEW AND SHALL BE REVIEWED BY DBPR, PLANS STAMPED AND
	WORKSHEETS ATTACHED AS REQUESTED.

	3. A GREASE INTERCEPTOR MAY BE REQUIRED.
	PLEASE CONTACT LYNN MASSON,
	ENVIRONMENTAL COMPLIANCE (561) 822-2271,
	FAX (561) 822-2279, OR E-MAIL
	[email protected]. WASTE ORD. 3434.
	****RESPONSE NOTED BUT NOT ACCEPTABLE. PLEASE CONTACT
	ENVIRONMENTAL COMPLIANCE. GREASE TRAP INSIDE NOT
	APPROVED. PER MUNICIPAL CODE A MINIMUM 750 GAL.GREASE
	INTERCEPTOR IS REQUIRED.

	4. OK
	5. OK
	6. OK

	7. SHT P-1 WATER FILTERS SHALL BE
	COMPLIANT WITH NSF-42. SUBMIT MANUF.
	SPECIFICATION SHEETS.
	****RESPONSE NOTED. MANUFACTURE CUT SHEET INDICATED WAS
	NOT FOUND IN RESUBMITTAL.

	8. SHTS A-6 & P-1. SHT A-6 INDICATES A
	NEW OVEN, AND SHT P-1 INDICATES A FRYER
	AND THE OVEN AS RECONNECTING (GAS SIZE
	AND CAPACITY SAME EXISTING). A GAS
	PERMIT WILL BE REQUIRED AND THE
	FOLLOWING INFORMATION WILL BE REQUIRED
	TO VERIFY COMPLIANCE WITH THE GAS CODE:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.
	****RESPONSE NOTED. THE CORRESPONDING LENGTH FROM "B"
	TO "D" IS NOT INDICATED

	B. OK
	C. OK
	D. OK

	E. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).
	****RESPONSE NOTED. THE DISTANCE SHOWN IS NOT CORRECT.
	ADDING WHAT IS SHOWN IS MINIMUM 68' FROM "F" TO "C",
	AND 64' FROM "F" TO "A" BUT THE SECTION BETWEEN "B"

	F. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.
	****RESPONSE NOTED. FLORIDA PUBLIC UTILITIES PROVIDES
	2LB OR .5 LB WITH A .5 INCHWC PRESSURE DROP. FBC-2004
	FUEL GAS TABLE 402.4(2). INDICATE THE PRESSURE AS .5
	PSI, NOT 1 PSI OR LESS.

	G. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2. (FOR
	ALL NEW EQUIPMENT).
	****RESPONSE NOTED. MANUF. SHEETS NOT SUBMITTED AND ARE
	REQUIRED FOR PLAN REVIEW.

	H. OK

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2006-11-01			Cont ID
Sent By	kstevens			Date	2006-09-29	Time	07:34	Rev Time	0.00
Received By	kstevens			Date	2006-09-29	Time	07:34	Sent To

Notes

2006-09-29 00:00:00	DENIED
	REFERENCE: FBC-2004 PLUMBING
	FBC-2004 FUEL GAS
	FBC-2004 CHAPTER 1
	FBC-2004 CHAPTER 11
	FLORIDA ADMINISTRATIVE CODE
	FLORIDA STATUES

	1. ALL SHEETS. THE ARCHITECTS TITLE
	BLOCK DOES NOT REFLECT THE ADDRESS FOUND
	ON THE DBPR WEBSITE. FAC 61G1-16.004(1)
	AND FS 481.2055. (SEE ATTACHED SHEET).

	2. ROUTE PLANS TO DBPR HOTEL AND
	RESTURANT DIVISION FOR REVIEW. MINIMUM 2
	SETS OF STAMPED PLANS WITH THE TWO PAGE "WORKSHEETS"
	REQUIRED FOR REVIEW.
	SECTION 102.2.1.

	3. A GREASE INTERCEPTOR MAY BE REQUIRED.
	PLEASE CONTACT LYNN MASSON,
	ENVIRONMENTAL COMPLIANCE (561) 822-2271,
	FAX (561) 822-2279, OR E-MAIL
	[email protected]. WASTE ORD. 3434.

	4. SHT A-5 PLEASE SHOW COMPLIANCE WITH
	THE FOLLOWING:
	A. 11-4.16.5 FLUSH CONTROLS
	B. 11-4.19.5 FAUCETS

	5. SHT P-1 ALL EQUIPMENT & FIXTURES
	UTILIZED FOR STORAGE, PREPARATION AND
	HANDLING OF FOOD SHALL DISCHARGE THROUGH
	AN INDIRECT WASTE PIPE BY MEANS OF AN
	AIR GAP. SECTION 802.1.1. - FLOOR SINKS
	ARE REQUIRED PER SECTION 802.3.

	6. SHT P-1 PLUMBING NOTES #13 AIR
	CHAMBERS ARE NOT APPROVED. WATER HAMMER
	ARRESTORS REQUIRED AT QUICK CLOSING
	VALVES SHALL BE LOCATED NEAR THE
	FIXTURES IN AN "EFFECTIVE RANGE", (NOT
	IN THE CEILING), PER PDI-WH 201 AND
	MANUF. INSTALLATION INSTRUCTIONS. (ICE
	MAKERS, DISHWASHERS, ETC).

	7. SHT P-1 WATER FILTERS SHALL BE
	COMPLIANT WITH NSF-42. SUBMIT MANUF.
	SPECIFICATION SHEETS.

	8. SHTS A-6 & P-1. SHT A-6 INDICATES A
	NEW OVEN, AND SHT P-1 INDICATES A FRYER
	AND THE OVEN AS RECONNECTING (GAS SIZE
	AND CAPACITY SAME EXISTING). A GAS
	PERMIT WILL BE REQUIRED AND THE
	FOLLOWING INFORMATION WILL BE REQUIRED
	TO VERIFY COMPLIANCE WITH THE GAS CODE:

	A. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.

	B. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE IF BEING USED.

	C. TYPE OF GAS, (LP OR NATURAL).

	D. BTU LOAD OF EACH APPLIANCE AND THE
	TOTAL BTU LOAD ON THE SYSTEM. REFER TO
	THE FBC-2004 FUEL GAS CODE SECS. 401.8
	THRU 402.6.1 AND TABLES 402.4(1) THRU
	402.4(33).

	E. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER), TO THE MOST REMOTE
	OUTLET IN THE BUILDING AND/OR SYSTEM PER
	FBC-2004 FUEL GAS CODE APPENDIX A - USE
	OF CAPACITY TABLES A.3.1(4).

	F. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.

	G. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2. (FOR
	ALL NEW EQUIPMENT).

	H. EMERGENCY HOOD SHUT DOWN SHUT OFF
	VALVE TO BE BELOW CEILING. MANUAL SHUT
	OFF VALVE TO BE UPSTREAM. UNION TO BE
	DOWN STREAM OF MANUAL VALVE. (INDICATED
	AS EXISTING RELOCATING).

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	Z			ZONING
Rev No	1	Status	N	Date	2006-11-03			Cont ID
Sent By	mflis			Date	2006-11-03	Time	11:50	Rev Time	0.00
Received By	mflis			Date	2006-11-03	Time	11:50	Sent To

Notes

2006-11-03 11:51:05

INTERIOR REMODEL ONLY - NO DMP REVIEW NECESSARY