City of West Palm Beach eGovPlus

Plan Review Details - Permit 06061574

Plan Review Stops For Permit 06061574

Review Stop	G			GAS REVIEW
Rev No	3	Status	P	Date	2006-08-14			Cont ID
Sent By	mperson			Date	2006-08-14	Time	15:58	Rev Time	0.33
Received By	mperson			Date	2006-08-14	Time	15:58	Sent To	PC

Notes

2006-08-14 00:00:00

REFERENCE: GEN/RES PERMIT #06061238

Review Stop	G			GAS REVIEW
Rev No	2	Status	F	Date	2006-07-25			Cont ID
Sent By	mperson			Date	2006-07-25	Time	09:04	Rev Time	0.33
Received By	mperson			Date	2006-07-25	Time	09:04	Sent To	PC

Notes

2006-07-25 00:00:00	****DENIED 2ND TIME****
	REFERENCE: FBC-2004 FUEL GAS
	FBC-2004 CHAPTER 1

	THE FOLLOWING INFORMATION IS STILL
	REQUIRED FOR GAS PLAN REVIEW:

	1. A GAS PERMIT CAN NOT BE ISSUED UNTIL
	A GEN/RES PERMIT APPLICATION HAS BEEN
	APPLIED FOR AND APPROVED BY ZONING FOR
	THE GENERATOR LOCATION.(NOTE: FAILED
	GEN/RES PERMIT APPLICATION HAS NOT BEEN
	RESUBMITTED FOR ZONING TO PASS, PLEASE
	SEE ATTACHED SHEETS.)
	2. PER FBC-2004, CHAPTER 1, SECTION
	106.1.1 INFORMATION ON CONSTRUCTION
	DOCUMENTS. CONSTRUCTION DOCUMENTS SHALL
	BE OF SUFFICIENT CLARITY TO INDICATE THE
	LOCATION, NATURE AND EXTENT OF THE WORK
	PROPOSED AND SHOW IN DETAIL THAT IT WILL
	CONFORM TO THE PROVISIONS OF THIS CODE
	AND RELAVENT LAWS, ORDINANCES, RULES AND
	REGULATIONS, AS DETERMINED BY THE
	BUILDING OFFICIAL. (NOTE: THE ISOMETRIC
	DRAWING IS STILL MISSING THE FOLLOWING
	INFORMATION, PLEASE SEETHE FOLLOWING
	COMMENTS AND THE CORRECTED DRAWING IN
	RED INK FOR REFERENCE FOR RESUBMITTAL.
	ALSO REFERENCE EXAMPLE OF ISOMETRIC
	DRAWING FOR RESUBMITTAL.)
	3. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.
	4. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED AND ALL PIPE SIZES.
	5. FBC-2004 CHAPTER 1,SECTION 106.3.4.2:
	THE PERSON RESPONSIBLE FOR THE DESIGN OF
	THE DRAWING SHALL CLEARLY PRINT AND SIGN
	NAME, AND ALSO DATE DRAWING. PLEASE DO
	THIS PRIOR TO RESUBMITTING.

	**IN ORDER TO EXPIDITE PLAN REVIEW: WHEN
	RESUBMITTING, PLEASE REPLACE ONLY SHEETS
	WHICH HAVE CHANGED AND PROVIDE ONE COPY
	OF ALL OLD/VOIDED SHEETS FOR REFERENCE
	ONLY. PLEASE REFERENCE CORRECTED
	ISOMETRIC GAS RISER IN RED INK FOR
	RESUBMITTAL.

	END OF COMMENTS:

	REVIEW BY MIKE PERSON
	(561) 805-6730
	FAX (561) 805-6731
	E-MAIL [email protected]
	UNDER SUPERVISION OF K.STEVENS
	(561) 805-6721

Review Stop	G			GAS REVIEW
Rev No	1	Status	F	Date	2006-07-05			Cont ID
Sent By	mperson			Date	2006-07-05	Time	11:58	Rev Time	0.33
Received By	mperson			Date	2006-07-05	Time	11:58	Sent To	PC

Notes

2006-07-05 00:00:00	****DENIED****
	REFERENCE: FBC-2004 FUEL GAS

	THE FOLLOWING INFORMATION IS REQUIRED
	FOR PLAN REVIEW FOR A GAS PERMIT:

	1. A GAS PERMIT CAN NOT BE ISSUED UNTIL
	A GEN/RES PERMIT APPLICATION HAS BEEN
	APPLIED FOR AND APPROVED BY ZONING FOR
	THE GENERATOR LOCATION.(NOTE ZONING
	FAILED PERMIT APPLICATION 6/25/06.
	PLEASE SEE ATTACHED ZONING PERMIT PLAN
	REVIEW FOR REFERENCE FOR RESUBMITTAL.)
	2. SUBMIT AN ISOMETRIC DRAWING THAT
	CLEARLY SHOWS ALL CUT SECTIONS OF PIPE
	AND CORRESPONDING LENGTHS PER FBC-2004
	FUEL GAS CODE.
	3. TYPE OF GAS, (LP OR NATURAL) PLEASE
	INDICATE GAS TYPE ON DRAWING.
	4. SHOW TYPE OF PIPING MATERIAL BEING
	INSTALLED, ALL PIPE SIZES, (AND THE EDH
	NUMBER OF CORRUGATED STAINLESS STEEL
	TUBING FOR EACH PIPE SIZE BEING USED.
	5. SHOW THE DISTANCE FROM THE POINT OF
	DELIVERY, (METER OR TANK), TO THE MOST
	REMOTE OUTLET IN THE BUILDING AND/OR
	SYSTEM PER FBC-2004 FUEL GAS CODE
	APPENDIX A - USE OF CAPACITY TABLES
	A.3.1(4).
	6. BTU LOAD OF EACH APPLIANCE AND THE
	TOTAL BTU LOAD ON THE SYSTEM. REFER TO
	THE FBC-2004 FUEL GAS CODE SECS. 401.8
	THRU 402.6.1 AND TABLES 402.4(1) THRU
	402.4(33).(NOTE: THIS INCLUDES EXISTING
	SYSTEM BTU LOAD AS WELL AS NEW BTU LOAD)
	7. INDICATE THE DELIVERY PRESSURE (PSI)
	PER FBC-2004 FUEL GAS CODE SEC. 402.2.
	NATURAL GAS SPECIFY .5 PSI OR 2 PSI.
	PROPANE 10 PSI.
	8. SUBMIT MANUFACTURE SHEETS FOR ALL GAS
	EQUIPMENT TO VERIFY COMPLIANCE WITH
	STANDARDS NFPA 54, NFPA 58, AND THE
	FBC-2004 FUEL GAS CODE SEC 402.2 (NOTE:
	NEED MANUFACTURE CUT SHEET OF REGULATOR
	TO COMPLY WITH THE ABOVE.)
	9. FBC-2004 CHAPTER 1, SECTION 106:
	THE PERSON RESPONSIBLE FOR THE DESIGN OF
	THE DRAWING SHALL CLEARLY PRINT AND SIGN
	NAME, AND ALSO DATE DRAWING.

	END OF COMMENTS:

	REVIEW BY MIKE PERSON
	(561) 805-6730
	FAX (561) 805-6731
	E-MAIL [email protected]
	UNDER SUPERVISION OF K.STEVENS
	(561) 805-6721

Review Stop	I			INCOMING/PROCESSING
Rev No	3	Status	N	Date	2006-08-03			Cont ID
Sent By	adarroug			Date	2006-08-03	Time	11:26	Rev Time	0.00
Received By	adarroug			Date	2006-08-03	Time	11:26	Sent To	G

Notes

2006-08-03 00:00:00

TO "MPERSON" DESK/RESUB

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2006-07-22			Cont ID
Sent By	adarroug			Date	2006-07-22	Time	13:29	Rev Time	0.00
Received By	adarroug			Date	2006-07-22	Time	13:29	Sent To	G

Notes

2006-07-22 00:00:00

TO "G" BOX/RESUB

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2006-07-05			Cont ID
Sent By	adarroug			Date	2006-07-05	Time	13:29	Rev Time	0.00
Received By	adarroug			Date	2006-06-30	Time	11:30	Sent To

Notes

2006-06-30 00:00:00

TO "G" BOX