| Date |
Text |
| 2022-12-28 13:42:04 | RESIDENTIAL (R3) REVISION, ADDITION/ALTERATION THIRD |
| | BUILDING REVIEW COMMENTS |
| | CODE: FBC 7TH EDITION (2020) AND CITY AMENDMENTS. |
| | PRMIT #22070105 |
| | 213 MARLBOROUGH RD |
| | |
| | NOTE: |
| | BUILDING REVIEW MAY BE APPROVED WITH PROVISO. PROVISO |
| | MEANS CONTRACTOR WILL SUBMIT REQUIRED INFORMATION AFTER |
| | THE PERMIT IS ISSUED BUT BEFORE INSPECTIONS TO AVOID |
| | CONFLICTS/DELAYS. REVISION FEES APPLY (NOTE: FEES DON'T |
| | APPLY TO PRODUCT APPROVAL SUBMITTAL, EXCEPT FOR PRODUCT |
| | APPROVALS ALREADY REVIEWED/APPROVED). |
| | |
| | ***IMPORTANT****CONTRACTOR TO ADVICE IF PROVISO OPTION |
| | IS PREFERRED AT THIS TIME OR IF RE-SUBMITTING REQUIRED |
| | INFORMATION BEFORE PERMIT ISSUANCE. |
| | |
| | |
| | 1-6 OK. |
| | |
| | ORIGINAL COMMENT: |
| | 7- PROVIDE COMPLETE FRAMING PLANS, SECTIONS AND |
| | SPECIFICATIONS FOR RE-CONSTRUCTION OF WOOD CORNICE & |
| | BARREL TILE ROOF SHOWN ON PLANS FOR FIRST FLOOR. |
| | SPECIFY ALL FRAMING MEMBERS AND CONNECTORS, ETC. SEC. |
| | R301.2.1 FBC-RESIDENTIAL. |
| | |
| | RESPONSE: |
| | PARAPET DETAIL ON SHEET A-01 IS INCOMPLETE. IT DOESN'T |
| | SPECIFY ALL FRAMING MEMBERS AND ALL CONNECTORS FOR |
| | PARAPET WALL. NEED TO PROVIDE THIS INFORMATION. |
| | |
| | ORIGINAL COMMENT: |
| | 8- CLARIFY/REVISE SIZE OF EMERGENCY OVERFLOW SCUPPERS |
| | SPECIFIED ON PLANS. SEC. R903.4.1 FBC-RESIDENTIAL. |
| | NOTE: 2" EMERGENCY OVERFLOW SCUPPER DOESN'T COMPLY. |
| | |
| | RESPONSE: |
| | EMERGENCY OVERFLOW SCUPPER SIZE (4"H X 2"W) DOESN'T |
| | COMPLY. SEE SEC. 1108.3 FBC-PLUMBING AS REQUIRED BY |
| | SEC. R903.4.1 FBC-RESIDENTIAL AND REVISE SIZE. |
| | |
| | 9- PRODUCT APPROVALS |
| | PROVIDE PRODUCT APPROVAL AS REQUIRED BY FAC 61G20-3.001 |
| | FOR: |
| | (NOTE: THIS MAY BE SUBMITTED LATER AS A DEFERRED |
| | SUBMITTAL. PROVIDE COMPLETE INFORMATION FOR REVIEW |
| | PRIOR TO INSTALLATION TO AVOID CONFLICTS/DELAYS. ALL |
| | PRODUCT APPROVALS NEED TO BE APPROVED IN WRITING BY |
| | DESIGNER OF RECORD PRIOR TO SUBMITTAL): |
| | |
| | ORIGINAL COMMENT: |
| | A)FLAT ROOF AND CLEARLY MARK/IDENTIFY WHICH ASSEMBLY IS |
| | GOING TO BE INSTALLED. IF SELECTED ASSEMBLY DOESN'T |
| | MEET THE DESIGN PRESSURES FOR ALL ROOF ZONES, THEN |
| | SIGNED AND SEALED RAS 117 CALCULATIONS ARE REQUIRED. |
| | |
| | RESPONSE: |
| | THERE ARE TWO DIFFERENT PRODUCT APPROVALS UPLOADED IN |
| | THE SAME PDF FILE. ONE IS CERTAINTEED FLORIDA PRODUCT |
| | APPROVAL FL2533-R28 AND THE OTHER ONE IS CERTAINTEED |
| | NOA 17-1003.15. IMPORTANT NEED TO SUBMIT ONLY ONE |
| | PRODUCT APPROVAL TO AVOID CONFLICTS. |
| | |
| | NOTE: |
| | EITHER PRODUCT APPROVAL REQUIRES SIGNED AND SEALED RAS |
| | 117 CALCULATIONS BECAUSE THE SELECTED ASSEMBLIES DON'T |
| | MEET THE DESIGN PRESSURES FOR ALL ROOF ZONES. THE |
| | MAXIMUM DESIGN PRESSURES (MDP) ON SELECTED ASSEMBLY |
| | W-77 CERTAINTEED FLORIDA PRODUCT APPROVAL FL2533-R28 IS |
| | -60PSF. AND THE DESIGN PRESSURES ON CERTAINTEED NOA |
| | 17-1003.15 WERE NO IDENTIFIED BECAUSE NO ASSEMBLY WAS |
| | SELECTED. NEVERTHELESS NONE OF THE ASSEMBLIES ON NOA |
| | SUBMITTED MEET THE DESIGN PRESSURES FOR ALL ROOF ZONES. |
| | NOTE: WHEN SELECTING AN ASSEMBLY MAKE SURE SELECTED |
| | ASSEMBLY IS NOT LIMITED BY GENERAL LIMITATION #9 |
| | BECAUSE THIS LIMITATION DOESN'T ALLOW NAIL ENHANCEMENT. |
| | SEE GENERAL LIMITATION #9 ON LAST PAGE OF NOA. |
| | SEC.107.2.1 CITY AMENDMENTS. |
| | |
| | PREVIOUS COMMENT: |
| | B) ARCHITECT'S RESPONSE LETTER STATES "GC REVISED |
| | OUTSWING FRENCH DOOR SUBMITTAL. NEW SUBMITTAL |
| | ATTACHED.". |
| | NOTHING WAS UPLOADED TO PROJECTDOX FOR REVIEW. |
| | NOTE: NEED PRODUCT APPROVAL FOR INSWING FRENCH DOORS AS |
| | SHOWN ON THE SECOND FLOOR. CHECK DESIGN PRESSURES |
| | SPECIFIED ON PLANS. |
| | |
| | RESPONSE: |
| | PRODUCT APPROVAL FOR SINGLE "OUTSWING" DOOR WAS |
| | SUBMITTED BUT PRODUCT APPROVAL FOR DOUBLE INSWING DOORS |
| | WAS NOT SUBMITTED. |
| | |
| | ORIGINAL COMMENT: |
| | C)ROOF TILE AND CLEARLY MARK ADHESIVE PADDY SIZE TO BE |
| | USED AS REQUIRED BY CITY POLICY FOR ALL ROOFING PERMITS |
| | TO VERIFY COMPLIANCE WITH THE DESIGN PRESSURES OF SEC |
| | R301.2.1 FBC-RESIDENTIAL. |
| | |
| | RESPONSE: |
| | THERE ARE TWO DIFFERENT PRODUCT APPROVALS UPLOADED IN |
| | THE SAME PDF FILE. ONE IS CERAMICA VEREA FLORIDA |
| | PRODUCT APPROVAL FL17152-R4 AND THE OTHER ONE IS TEJAS |
| | VEREA NOA 20-0902.03. IMPORTANT NEED TO SUBMIT ONLY ONE |
| | PRODUCT APPROVAL AND CLEARLY MARK FASTENING METHOD TO |
| | AVOID CONFLICTS |
| | NOTE: FLORIDA PRODUCT APPROVAL FL17152-R4 IS NOT MARKED |
| | SHOWING THE FASTENING METHOD. NOA 20-0902.03 IS MARKED |
| | WITH AH-160 ADHESIVE ON PAGE 5 OF 9. THIS FASTENING |
| | METHOD IS OK FOR ALL ROOF ZONES BUT ADHESIVE PRODUCT |
| | APPROVAL SUBMITTED DOESN'T MATCH AH-160 ADHESIVE LISTED |
| | IN THE NOA. COORDINATE AS REQUIRED TO AVOID MORE |
| | CONFLICTS/DELAYS. SEC.107.2.1 CITY AMENDMENTS. |
| | |
| | ORIGINAL COMMENT: |
| | D)PROVIDE A ROOF TILE ADHESIVE PRODUCT APPROVAL THAT IS |
| | LISTED ON THE ROOF TILE PRODUCT APPROVAL SUBMITTED. |
| | |
| | RESPONSE: |
| | COORDINATE WITH ITEM #9(C) ABOVE TO AVOID MORE |
| | CONFLICTS/DELAYS. SEC.107.2.1 CITY AMENDMENTS. |
| | |
| | ORIGINAL COMMENT: |
| | E) HIP AND RIDGE INSTALLATION TO BE USED. AND, CLEARLY |
| | MARK ON PRODUCT APPROVAL ATTACHMENT METHOD. SEC. |
| | R905.3.7.1 FBC-RESIDENTIAL. |
| | |
| | RESPONSE: |
| | FLORIDA PRODUCT APPROVAL FL5374-R6 SUBMITTED IS OK. |
| | NOTE: COORDINATE ROOF TILE ADHESIVE WITH ITEM #9(C) |
| | ABOVE TO AVOID MORE CONFLICTS/DELAYS. SEC.107.2.1 CITY |
| | AMENDMENTS. |
| | |
| | ORIGINAL COMMENT: |
| | 10- DESIGNER OF RECORD TO REVIEW AND APPROVE IN WRITING |
| | (NOT SIGNING AND SEALING) ALL PRODUCT APPROVALS AS |
| | REQUIRED BY SEC. 107.3.4.1 CITY AMENDMENTS. |
| | |
| | RESPONSE: |
| | NOT ADDRESSED. |
| | NOTE: THIS COMMENT APPLIES TO ALL PRODUCT APPROVALS |
| | SUBMITTED, INCLUDING ONES SUBMITTED EARLIER. |
| | |
| | WHEN RESUBMITTING, A TRANSMITTAL LETTER LISTING THE |
| | ORIGINAL REVIEW COMMENT WITH A DESCRIPTION OF WHERE AND |
| | HOW THE COMMENT WAS ADDRESSED WILL HELP TO EXPEDITE THE |
| | REVIEW PROCESS. THANK YOU FOR YOUR ANTICIPATED |
| | COOPERATION. |
| | |
| | PLEASE FEEL FREE TO CONTACT ME IF YOU HAVE ANY |
| | QUESTIONS REGARDING THESE COMMENTS, |
| | JULIO GOMEZ |
| | COMMERCIAL COMBINATION PLANS EXAMINER |
| | DEVELOPMENT SERVICES DEPARTMENT |
| | BUILDING DIVISION |
| | (561)805-6712 |
| | [email protected] |
| | |
| | |
| | |
