| Date |
Text |
| 2022-11-08 15:16:14 | RESIDENTIAL (R3) REVISION, SECOND BUILDING REVIEW |
| | COMMENTS |
| | CODE: FBC 7TH EDITION (2020) AND CITY AMENDMENTS. |
| | REVISION #22070103 211 MARLBOROUGH RD |
| | |
| | 1- OK. |
| | 2- OK. |
| | |
| | 3- OK. CBAA CASE #1455 WAS APPROVED. |
| | |
| | ORIGINAL COMMENT: |
| | 4- WINDOWS AND DOORS DESIGN PRESSURES SHOWN ON THE |
| | ARCHITECTURAL EXTERIOR ELEVATIONS DON'T MATCH THE |
| | DESIGN PRESSURES CALCULATED BY THE STRUCTURAL ENGINEER. |
| | REVISE AS REQUIRED TO MATCH. SEC. R301.2.1 |
| | FBC-RESIDENTIAL. |
| | |
| | RESPONSE: |
| | DESIGN PRESSURES WERE REMOVED FROM THE ENGINEER'S |
| | DRAWINGS. DESIGN PRESSURES SHOWN ON THE ARCHITECTURAL |
| | PLANS ARE TOO LOW FOR BUILDING LOCATED IN EXPOSURE "D" |
| | AS SPECIFIED BY THE ENGINEER OF RECORD UNDER THE WIND |
| | DESIGN DATA. REVISE AS REQUIRED. SEC. R301.2.1 |
| | FBC-RESIDENTIAL. |
| | |
| | 5- OK. |
| | 6- OK. |
| | 7- OK. |
| | 8- OK. |
| | |
| | ORIGINAL COMMENT: |
| | 9- PROVIDE COMPLETE FRAMING PLANS FOR NEW 30"X96" |
| | SKYLIGHT AND FOR NEW SOLAR TUBES. SEC. R301.2.1 |
| | FBC-RESIDENTIAL. |
| | |
| | RESPONSE: |
| | ARCHITECT'S RESPONSE LETTER SAYS FRAMING DETAILS HAVE |
| | BEEN ADDED TO STRUCTURAL DRAWINGS. STRUCTURAL DRAWINGS |
| | SAYS SKYLIGHT SEE ARCH ???L DRAWINGS. INFORMATION WAS |
| | NOT PROVIDED. PROVIDE COMPLETE FRAMING DETAILS. SPECIFY |
| | ALL FRAMING MEMBERS & CONNECTORS. |
| | |
| | ORIGINAL COMMENT: |
| | 10- GUARDRAILS: DESIGNER OF RECORD NEEDS TO PROVIDE THE |
| | DETAILS AND SPECIFICATIONS FOR THE CONSTRUCTION OF THE |
| | BALCONY AND TERRACE GUARDRAILS AS REQUIRED BY TABLE |
| | R301.5, SEC. AND SEC. R312.1 FBC-RESIDENTIAL. |
| | NOTE: SUBSEQUENT SHOP DRAWINGS ARE TO CONFIRM THAT |
| | DESIGN DETAILS AND SPECIFICATIONS ARE MET. |
| | |
| | RESPONSE: |
| | ARCHITECTURAL PLANS SAYS SEE STRUCTURAL DRAWINGS. |
| | STRUCTURAL DRAWINGS SAYS SEE ARCHITECTURAL DRAWINGS. |
| | INFORMATION WAS NOT SUBMITTED. |
| | |
| | NOTE; ITEM #11 WILL BE REVIEWED ONCE DESIGN PRESSURES |
| | ARE REVISED. SEE ITEM #4 ABOVE. PLEASE MAKE SURE BELOW |
| | COMMENTS FOR EACH PRODUCT APPROVAL IS ADDRESSED TO |
| | AVOID CONFLICTS/DELAYS. |
| | 11- PRODUCT APPROVALS |
| | PROVIDE PRODUCT APPROVAL AS REQUIRED BY FAC 61G20-3.001 |
| | FOR: |
| | (NOTE: THIS MAY BE SUBMITTED LATER AS A DEFERRED |
| | SUBMITTAL. PROVIDE COMPLETE INFORMATION FOR REVIEW |
| | PRIOR TO INSTALLATION TO AVOID CONFLICTS/DELAYS. ALL |
| | PRODUCT APPROVALS NEED TO BE APPROVED IN WRITING BY |
| | DESIGNER OF RECORD PRIOR TO SUBMITTAL): |
| | |
| | A)SOLATUBE FLORIDA PRODUCT APPROVAL SUBMITTED |
| | (FL11480-R13) DOESN'T MEET THE DESIGN PRESSURES |
| | CALCULATED BY THE ENGINEER OF RECORD ON SHEET S-000. |
| | NEED TO PROVIDE PRODUCT APPROVAL THAT MEETS OR EXCEEDS |
| | CALCULATED DESIGN PRESSURES. |
| | |
| | B)SKYLIGHT (30"X96") NOA 20-1013.05 SUBMITTED DOESN'T |
| | MEET THE DESIGN PRESSURES CALCULATED BY THE ENGINEER OF |
| | RECORD ON SHEET S-000. NEED TO PROVIDE PRODUCT APPROVAL |
| | THAT MEETS OR EXCEEDS CALCULATED DESIGN PRESSURES. |
| | |
| | C)SINGLE OUTSWING FRENCH DOOR FL34006 SUBMITTED DOESN'T |
| | MEET THE DESIGN PRESSURES CALCULATED BY THE ENGINEER OF |
| | RECORD ON SHEET S-200. NEED TO PROVIDE PRODUCT APPROVAL |
| | THAT MEETS OR EXCEEDS CALCULATED DESIGN PRESSURES. |
| | NOTE: PLEASE UPLOAD THE FLORIDA PRODUCT APPROVAL COVER |
| | PAGE AND CORRESPONDING INSTALLATION DRAWINGS ON THE |
| | SAME PDF FILE. DO NOT UPLOAD IN SEPARATE FILES. |
| | |
| | D)WINDOW MULLIONS FLORIDA PRODUCT APPROVAL FL34545 |
| | SUBMITTED. NOTE: NEED TO SPECIFY MULLION SIZE TO VERIFY |
| | PRESSURES. SEC. R301.2.1 FBC-RESIDENTIAL. |
| | |
| | E)FIXED WINDOW FLORIDA PRODUCT APPROVAL FL34706 |
| | SUBMITTED: SHEET 2 OF 7 OF INSTALLATION DRAWINGS SHOWS |
| | TYPE GLASS "B" TO BE USED. THIS TYPE OF GLASS IS NOT |
| | COVERED IN THE DESIGN LOADS CAPACITY TABLES FOR 4"-2" X |
| | 6'-10" WINDOW "A1" SPECIFIED ON SHEET A-09. SEE SHEETS |
| | 3 OF 7 AND 4 OF 7 OF INSTALLATION DRAWINGS AND REVISE |
| | AS REQUIRED OR PROVIDE PRODUCT APPROVAL THAT WORKS TO |
| | MEET THE CALCULATED DESIGN PRESSURES. |
| | |
| | F)FLAT ROOF AND CLEARLY MARK/IDENTIFY WHICH ASSEMBLY IS |
| | GOING TO BE INSTALLED. IF SELECTED ASSEMBLY DOESN'T |
| | MEET THE DESIGN PRESSURES FOR ALL ROOF ZONES, THEN |
| | SIGNED AND SEALED RAS 117 CALCULATIONS ARE REQUIRED. |
| | NOTE: THERE ARE DIFFERENT TYPES OF CONSTRUCTION IN THIS |
| | HOUSE. CONCRETE ROOF (NEW TERRACE) AND WOOD FRAMED |
| | (EXISTING ROOFS). ALSO, THERE ARE SOME FLAT ROOF TO BE |
| | COVERED WITH TILE AND THERE IS THE MAIN ROOF, NOT A |
| | DECK. PROVIDE PRODUCT APPROVAL COMPATIBLE EACH PROPOSED |
| | APPLICATION. |
| | |
| | G) ROOF TILE AND CLEARLY MARK ADHESIVE PADDY SIZE TO BE |
| | USED AS REQUIRED BY CITY POLICY FOR ALL ROOFING PERMITS |
| | TO VERIFY COMPLIANCE WITH THE DESIGN PRESSURES OF SEC |
| | R301.2.1 FBC-RESIDENTIAL. |
| | |
| | H)PROVIDE A ROOF TILE ADHESIVE PRODUCT APPROVAL THAT IS |
| | LISTED ON THE ROOF TILE PRODUCT APPROVAL SUBMITTED. |
| | |
| | I) HIP AND RIDGE INSTALLATION TO BE USED. AND, CLEARLY |
| | MARK ON PRODUCT APPROVAL ATTACHMENT METHOD. SEC. |
| | R905.3.7.1 FBC-RESIDENTIAL. |
| | |
| | 12-DESIGNER OF RECORD TO REVIEW AND APPROVE IN WRITING |
| | (NOT SIGNING AND SEALING) ALL PRODUCT APPROVALS AS |
| | REQUIRED BY SEC. 107.3.4.1 CITY AMENDMENTS. |
| | |
| | RESPONSE: |
| | TO BE COORDINATED WITH ITEM #11 ABOVE. PLEASE MAKE SURE |
| | ALL PRODUCT APPROVALS ARE REVIEWED/APPROVED TO AVOID |
| | CONFLICTS/DELAYS. |
| | |
| | WHEN RESUBMITTING, A TRANSMITTAL LETTER LISTING THE |
| | ORIGINAL REVIEW COMMENT WITH A DESCRIPTION OF WHERE AND |
| | HOW THE COMMENT WAS ADDRESSED WILL HELP TO EXPEDITE THE |
| | REVIEW PROCESS. THANK YOU FOR YOUR ANTICIPATED |
| | COOPERATION. |
| | |
| | PLEASE FEEL FREE TO CONTACT ME IF YOU HAVE ANY |
| | QUESTIONS REGARDING THESE COMMENTS, |
| | JULIO GOMEZ |
| | COMMERCIAL COMBINATION PLANS EXAMINER |
| | DEVELOPMENT SERVICES DEPARTMENT |
| | BUILDING DIVISION |
| | (561)805-6712 |
| | [email protected] |
| | |
| | |
| | |
