| Date |
Text |
| 2022-12-06 15:17:47 | NEW RESIDENTIAL HI RISE |
| | REVIEWED BY ROGER MCPHERSON |
| | 561-805-6716 |
| | [email protected] |
| | CODE USED FOR REVIEW - 2020 FBC WITH WPB CHAPTER 1 |
| | AMENDMENT |
| | |
| | CORRECTIONS NEEDED - |
| | |
| | 1) DRAWINGS APPEAR TO SHOW A DEAD END CORRIDOR ON THE |
| | SOUTH SIDE OF THE SOUTH STAIR ON THE 4TH FLOOR - PLEASE |
| | SHOW THE DEAD END CORRIDOR DIMENSIONS FOR THE 4TH FLOOR |
| | - FBC 1020.4 |
| | |
| | 2) TOILET REAR WALLS ARE SHOWN TO HAVE TILE - PLEASE |
| | SHOW THE WALL FINISH FOR THE SIDE WALLS WITHIN 2' OF |
| | TOILETS - PLEASE SHOW THE COMMON AREA RESTROOM WALL |
| | FINISH - (DRYWALL IS NOT CONSIDERED A HARD SURFACE) - |
| | FBC 1210.2.2 |
| | |
| | 3) BRIDGE RAMP HANDRAIL INSIDE OF BUILDING NEAR THE |
| | HALLWAY - DRAWING A704 - RAMP HAND RAIL EXTENSIONS |
| | INSIDE THE BUILDING APPEAR TO BE IN COLUMNS - PLEASE |
| | CLARIFY THE RAMP HAND RAIL EXTENSIONS - FBC FHA |
| | REQUIREMENT 2 ANSI 4.8.5 |
| | |
| | 4) DRAWINGS A106 AND LS103 DO NOT SHOW AS DIGITALLY |
| | SIGNED IN ADOBE READER - SIGNED AND SEALED DRAWINGS IN |
| | PROJECTDOX NEED TO BE DIGITALLY/ELECTRONICALLY SIGNED |
| | TO BE USED IN ELECTRONIC PLAN REVIEW. (A |
| | CERTIFICATE-BASED DIGITAL SIGNATURE (OFTEN JUST CALLED |
| | A DIGITAL SIGNATURE) IS A SPECIFIC TYPE OF |
| | E-SIGNATURE). |
| | |
| | 5) DRAWINGS SHOW UNIT FLOORING USING 1/4" SOUND PAD - |
| | THE FLOORING SYSTEM WILL NEED TO BE TESTED AFTER |
| | INSTALLATION OR PROVIDE THE FOLLOWING TEST REPORTS |
| | BEFORE INSTALLATION - PLEASE STATE ON THE DRAWINGS YOUR |
| | INTENTIONS. YOU CAN ADD THE FLOORING SYSTEM TEST |
| | REPORTS TO THE DEFERRED DOCUMENTS LIST ON THE DRAWINGS. |
| | THE FOLLOWING ACUSTICAL TEST REPORTS ARE REQUIRED |
| | BEFORE FLOORING INSTALLATION OR A FIELD TEST AFTER |
| | INSTALLATION: |
| | |
| | MANUFACTURER SPEC SHEETS ARE NOT ACCEPTABLE DUE TO |
| | DISCREPANCIES BETWEEN SPEC SHEETS/BROCHURES AND TEST |
| | REPORTS FOR SOME MANUFACTURERS (NOT NECESSARILY THE |
| | MANUFACTURER SELECTED; THIS IS A GENERAL COMMENT) |
| | |
| | A. FBC 1207.2, FLOOR/CEILING ASSEMBLIES SEPARATING |
| | DWELLING UNITS FROM EACH OTHER OR FROM PUBLIC OR |
| | SERVICE AREAS SHALL HAVE A SOUND TRANSMISSION CLASS |
| | (STC) OF NOT LESS THAN 50 (45 IF FIELD TESTED) FOR AIR |
| | BORNE NOISE WHEN TESTED IN ACCORDANCE WITH ASTM E 90.. |
| | PROVIDE A COPY OF THE TEST REPORT. (A DROP CEILING |
| | SHOULD NOT BE INCLUDED IN THE FLOOR/CEILING ASSEMBLY |
| | DESCRIPTION UNLESS THE UNIT MATCHES THE TESTED DROP |
| | CEILING DESCRIPTION) |
| | |
| | B. FBC 1207.3, FLOOR/CEILING ASSEMBLIES BETWEEN |
| | DWELLING UNITS OR BETWEEN A DWELLING UNIT AND A PUBLIC |
| | OR SERVICE AREA WITHIN THE STRUCTURE SHALL HAVE AN |
| | IMPACT INSULATION CLASS (IIC) RATING OF NOT LESS THAN |
| | 50 (45 IF FIELD TESTED) WHEN TESTED IN ACCORDANCE WITH |
| | ASTM E 492. PROVIDE A COPY OF THE TEST REPORT. (A DROP |
| | CEILING SHOULD NOT BE INCLUDED IN THE FLOOR/CEILING |
| | ASSEMBLY DESCRIPTION UNLESS THE UNIT MATCHES THE TESTED |
| | DROP CEILING DESCRIPTION) |
| | |
| | C. FBC 603.1, ALLOWABLE MATERIALS IN NON COMBUSTIBLE |
| | BUILDINGS, SEE ITEM 2, EXCEPTION 2, ACOUSTICAL |
| | INSULATION INSTALLED BETWEEN A FINISHED FLOOR AND SOLID |
| | DECKING WITHOUT INTERVENING AIRSPACE SHALL BE ALLOWED |
| | TO HAVE A FLAME SPREAD INDEX OF NOT MORE THAN 200. SEE |
| | 803.1.1, PROVIDE TEST DATA IN ACCORDANCE WITH ASTM E 84 |
| | OR UL 723. (DO NOT NEED THIS REPORT IF THE PADDING IS |
| | ATTACHED TO THE FLOORING) |
| | |
