| Date |
Text |
| 2021-09-17 11:17:01 | 1ST REVIEW FBC-2020 RES. BUILDING. |
| | PERMIT- 21090018 |
| | 9/17/2021 |
| | |
| | CODES IN EFFECT: |
| | FBC RES- FLORIDA RESIDENTIAL BUILDING CODE 7TH EDITION |
| | 2020 |
| | FBC EX- FLORIDA EXISTING BUILDING CODE 7TH EDITION 2020 |
| | FS- FLORIDA STATUTES |
| | FAC- FLORIDA ADMINISTRATIVE CODE |
| | WPB- WEST PALM BEACH AMENDMENTS TO THE FBC |
| | |
| | PLAN REVIEW RESULTS: DENIED. |
| | |
| | 1) SHEET 10B: PROVIDE A GAS RISER DRAWING- SECTION |
| | 107.3.5.3 (13) WPB AND SECTION G2412.3 & G2412.4 FBC |
| | RES. REFER TO FBC RES. CHAPTER 24 FUEL GAS- THE RISER |
| | SHALL INDICATE: |
| | A) TYPE OF GAS- NATURAL OR LP. |
| | B) DELIVERY PRESSURES AT THE 1ST AND 2ND STAGE |
| | REGULATORS. |
| | C) TOTAL BTU LOAD AND INDIVIDUAL APPLIANCE BTU LOADS. |
| | D) TYPES AND SIZES OF PIPING. |
| | E) TOTAL DEVELOPED LENGTH OF THE SYSTEM FROM THE METER |
| | TO THE MOST REMOTE APPLIANCE OUTLET. |
| | F) BRANCH AND CUT PIPE LENGTH MEASUREMENTS. |
| | G) LOCATIONS OF REGULATORS, SHUTOFF VALVES, AND PIPE |
| | UNIONS. |
| | H) OUTLET PRESSURES AT REGULATORS. |
| | I) LOCATIONS AND TYPES OF PIPE SLEEVES. |
| | K) PIPE SIZING TABLES. |
| | |
| | 2) INDICATE THE GALLON SIZE OF THE TANK ON THE PLAN AND |
| | SUBMIT MANUFACTURER?S SPECIFICATIONS VERIFYING IT HAS |
| | BEEN DESIGNED, FABRICATED, TESTED AND MARKED (STAMPED) |
| | IN ACCORDANCE WITH THE REGULATIONS AS REQUIRED BY THE |
| | REGULATORY AGENCIES AND COMPLIANCE STANDARDS LISTED IN |
| | SECTION 5.2.1.1 NFPA 58. THE TANK IS ASSUMED TO CONTAIN |
| | LP GAS- HOWEVER IT IS LABELED ?COMPRESSED GAS?. PLEASE |
| | LABEL IT CORRECTLY ON THE PLAN- SECTION 107.2.1 WPB. |
| | |
| | 3) PROVIDE A LP TANK INSTALLATION DETAIL SHOWING THE |
| | REQUIRED MASONRY OR OTHER NON-COMBUSTIBLE STRUCTURAL |
| | SUPPORTS LOCATED ON CONCRETE OR MASONRY FOUNDATION WITH |
| | THE CONTAINER SUPPORTS- SECTION 6.6.3.1 NFPA 58. SHOW |
| | HOW THE TANK WILL BE ANCHORED TO RESIST WIND LOAD AND |
| | WIND PRESSURES- SECTION 6.6.3.3 (D) NFPA 58. |
| | |
| | 4) SUBMIT MANUFACTURER?S SPECIFICATIONS FOR THE NEW |
| | RANGE IN COMPLIANCE WITH SECTION G2447.1 FBC RES. |
| | |
| | 5) PROVIDE COMBUSTION AIR CALCULATIONS AND INDICATE HOW |
| | THE THE AIR WILL BE PROVIDED- SECTION G2407.1. |
| | |
| | 6) CLARIFY IF AN EXHAUIST HOOD IS TO BE INSTALLED UNDER |
| | THIS PERMIT OR UNDER A SEPARATE AND PROVIDE DETAILS- |
| | SECTION 107.2.1 WPB. |
| | |
| | WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. |
| | |
| | CHRISTOPHER L. COLE |
| | BUILDING PLANS EXAMINER |
| | 401 CLEMATIS STREET |
| | WEST PALM BEACH FL 33401 |
| | 561-805-6719 |
| | [email protected] |
| | |
| | |
