| Date |
Text |
| 2021-04-29 06:46:31 | 1) SHT. LS 01 NOTES THE OCCUPANCY OF SPACE B03 AS AN |
| | "M" OCCUPANCY (MERCANTILE). THIS SPACE IS GOING TO BE A |
| | BEAUTY SHOP/NAIL SALON WHICH IS CLASSIFIED AS A GROUP |
| | "B" OCCUPANCY ACCORDING TO FBC-BUILDING SEC. 304.1. HOW |
| | CAN THIS BE CLASSIFIED AS AN "M" OCCUPANCY? IS THIS |
| | BUILDOUT A CHANGE OF OCCUPANCY/CHANGE OF USE? INDICATE |
| | ON THE PLAN. WPB AMEND. TO FBC SEC. 107.2.1. |
| | 2) INDICATE THE PREVIOUS OCCUPANCY OF ALL THE SPACES ON |
| | THIS PLAN AND INDICATE ON THE PLANS IF ANY OF THIS NEW |
| | WORK WILL BE A CHANGE OF OCUPANCY/CHANGE OF USE. WPB |
| | AMEND. TO FBC SEC. 107.2.1. |
| | 3) THE BREAKROOM SINK (NOT THE MOP SINK) IN THE |
| | EMPLOYEE BREAK AREA IN TENANT SPACE B03 SHALL COMPLY |
| | WITH THE FBC-ACCESS. SECS. 606.2, 606.3, 606.4, 606.5. |
| | 4) THE SINK IN ONE OF THE WAX ROOMS IN TENANT SPACE B03 |
| | SHALL COMPLY WITH FBC-ACCESS. SECS. 606.2, 606.3, |
| | 606.4, 606.5. |
| | 5) THE WALL FINISH AROUND THE MOP SINK SHALL OMPLY WITH |
| | FBC-BUILDING SEC.1210.2.2. |
| | 6) SHT. A631- DETAIL #1 - THE DOOR CANNOT SWING INTO |
| | THE CLEAR FLOOR SPACE FOR THE LAVATORY OR THE WATER |
| | CLOSET PER FBC SEC. 603.2.3 UNLESS A 30 INCH WIDE |
| | MINIMUM BY 48 INCH LONG MINIMUM CLEAR FLOOR SPACE IS |
| | PROVIDED WITHIN THE ROOM BEYOND THE ARC OF THE DOOR |
| | SWING. SHOW THE REQUIRED CCLEAR FLOOR SPACE OR REVERSE |
| | THE DOOR SWING. |
| | 7) SHT. A631 - THE HEIGHT OF THE GRAB BARS ARE SHOWN |
| | MEASURED TO THE CENTERLINE OF THE GRAB BARS. GRAB BARS |
| | SHALL BE MEASURED TO THE TOP OF THE GRIPPING SURFACE |
| | PER FBC-ACCESS. SEC. 609.4. |
| | 8) SHT. A631 - TOILET ACCESSORY MOUNTING HEIGHTS - THE |
| | OUTLET OF THE SOAP DISPENSER SHALL BE LOCATED A MAXIMUM |
| | OF 48 INCHES ABOVE THE FINISH FLOOR. FBC-ACCESS. |
| | SECS.308.2, 308.3. |
| | 9) SHT. A631 - ELEVATION #2 - THE LAVATORY SHALL BE |
| | LOCATED A MINIMUM OF 15 INCHES FROM THE WALL TO THE |
| | CENTERLINE OF THE LAVATORY PER FBC-PLUMBING |
| | SEC.405.3.1.THE PLANS SHOW THE LAVATORY AT 14 INCHES. |
| | 11) SINCE THIS IS A BUSINESS OCUPANCY A MINIMUM OF 2 |
| | DRINKING FOUNTAINS ARE REQUIRED PER FBC- PLUMBING TABLE |
| | 403.1 AND SEC.410.3. |
| | 12) SHT. P001 - NOTE #13 REFERS TO FIRE RATED FOAM, |
| | CAULKING OR PUTTY FOR SEALING PENETRATIONS THROUGH |
| | RATED WALLS. SUBMIT MANUFACTURER'S SPECIFICATIONS FOR |
| | THESE PRODUCTS TO ONIRM COMPATABILITY ITH THE |
| | PENETRATING ITEM. WPB AMEND. TO FBC SEC. 107.2.1. |
| | 13) SHT. P001 - WATER PIPE SIZING TABLE NOTE REFERS TO |
| | CHAPTER 4 OF MIAMI-DADE ORDINANCE 08-14. THIS NOTE IS |
| | NOT APPLICABLE. REMOVE THIS NOTE FROM THE PLANS. |
| | 14) SHT. P001 - WATER PIPE SIZING TABLE NOTE #2 REFERS |
| | TO FBC SECS. 2318.1.15 AND 2517.5.1.1.REMOVE THIS NOTE |
| | FROM THE PLANS AS BOTH SECTIONS ARE SHOWN AS "RESERVED" |
| | IN THE CODE AND NOT APPLICAABLE. |
| | 15) SHT. P001 - SHOW THE PAN DRAIN FOR THE WATER HEATER |
| | AND THE TERMINATION POINT OF THE PAN DRAIN ON THE WATER |
| | HEATER DETAIL.SHOW THE SIZE OF THE PAN DRAIN. |
| | 16) PROVIDE DETAILS OF THE SHELF CONSTRUCTION FOR THE |
| | WATER HEATER. THE WATER HEATER WILL WEIGH MORE THAN 665 |
| | POUNDS WHEN FILLED WITH WATER. THERE IS NO INFORMATION |
| | ON THE PLANS AS TO HOW THIS SHELF IS TO BE CONSTRUCTED |
| | OR ANY INFORMATION ON LOAD BEARING STRENGTH, |
| | CONNECTIONS, ETC. WPB AMEND. TO FBC SEC. 107.2.1. |
| | 17) SHT. P001 SHOWS A PRESSURE RELIEF VALVE ON THE COLD |
| | WATER INLET TO THE WATER HEATER. CLARIFY. |
| | 18) THE ENTIRE HOT WATER PIPING SYSTEM SHALL BE |
| | INSULATED WITH INSULATION WITH A WALL THICKNESS IN |
| | ACCORDANCE WITH FBC-ENERGY SEC.C404.4 AND TABLE |
| | C403..2.10. SHOW COMPLIANCE ON THE PLANS. |
| | 19) A BACKFLOW PREVENTER WILL BE REQUIRED ON THE WATER |
| | LINE TO THE TOWEL STEAMER.FBC-PLUMBING SEC.608.3. |
| | 20) HEATED WATER SUPPLY PIPING SHALL BE IN ACORDANCE |
| | WITH SECTION C404.5.1 OR C404.5.2. SHOW COMPLIANCE ON |
| | THE WATER RISER. |
| | 21) PROVISIONS SHALL BE MADE FOR THERMAL EXPANSION OF |
| | THE WATER SSUPPLY SYSTEM. IF THE PRESSURE RELIEF VALVE |
| | ON THE COLD WATER SYTEM IS TO MEET THIS PROVISION, |
| | LABEL THE VALVE AS A THERMAL EXXPAANSION VALVE AND |
| | SHOWW THE TERMINATION POINT OF THE DISCHARGE LINE OF |
| | THE VALVE. |
| | 22) THE WATER CONNECTION TOWEL STEAMER IS NOT SHOWN ON |
| | THE WATER RISER. CLARIFY. |
| | 23) SUBMIT A CONCRETE SLAB DETAIL SHOWING HOW THE SLAB |
| | CUTOUT WILL BE REPAIRED TO MAINTAIN THE STRUCTURAL |
| | INTEGRITY. INDICATE THE SIZE OF REINFORCING BARS TO BE |
| | USED, THE EMBEDMENT DEPTH THAT THE REBAR WILL BE |
| | DOWELED INTO THE EXISTING SLAB, HOW THE DOWELS WILL BE |
| | SET IN THE EXISTING SLAB, AND THE SPACING ON CENTER OF |
| | THE DOWELS. SHOW THE THICKNESS OF THE EXISTING SLAB & |
| | THE REPAIR. A VAPOR BARRIER AND TERMITE POISONING IS |
| | REQUIRED.WPB AMEND. TO 2010 FBC SEC.107.2.1. |
| | 24) THE WATER SUPPLY TO THE PEDICURE CHAIRS SHALL BE |
| | TEMPERED WATER PER FBC-PLUMBING SEC. 412.5. THE |
| | TEMPERED WATER VALVE SHALL COMPLY WITH ASSE 1070. |
| | 25) SHT. LS 01- SPACE B03 IS LABELED AS B03 BUT THE |
| | SAME SPACE IS LABELED AS B01 ON SHT.P101. CLARIFY. |
| | 26) SHT. A101 - IDENTIFY EACH BAY ON THE FLOOR PLAN. |
| | WPB AMEND. TO FBC SEC. 107.2.1. |
| | 27) SUBMIT MANUFACTURER'S SPECIFICATIONS/INSTALLATION |
| | MANUAL FOR THE PEDICURE CHAIRS.WPB AMEND. TO FBC SEC. |
| | 107.2.1. |
| | |
| | TIM LARGE |
| | CHIEF PLUMBING INSPECTOR |
| | PLUMBING PLAN REVIEW |
| | 561-805-6692 |
| | [email protected] |
| | |
