| Date |
Text |
| 2021-03-29 11:06:15 | NEW SFR |
| | REVIEWED BY ROGER MCPHERSON |
| | 561-805-6716 |
| | [email protected]. |
| | CODE USED FOR REVIEW - 2020 FBC WITH WPB CHAPTER 1 |
| | AMENDMENTS |
| | |
| | NO CHANGES SINCE THE LAST REVIEW |
| | |
| | CORRECTIONS NEEDED - FBC WPB AMENDMENTS 107 |
| | 1) PLEASE SHOW CARBON MONOXIDE DETECTOR LOCATION TO |
| | COMPLY WITH FBC R315.1 CARBON MONOXIDE PROTECTION. |
| | EVERY SEPARATE BUILDING OR AN ADDITION TO AN EXISTING |
| | BUILDING FOR WHICH A PERMIT FOR NEW CONSTRUCTION IS |
| | ISSUED AND HAVING A FOSSIL-FUEL-BURNING HEATER OR |
| | APPLIANCE, A FIREPLACE, AN ATTACHED GARAGE, OR OTHER |
| | FEATURE, FIXTURE, OR ELEMENT THAT EMITS CARBON MONOXIDE |
| | AS BYPRODUCT OF COMBUSTION SHALL HAVE AN OPERATIONAL |
| | CARBON MONOXIDE ALARM INSTALLED WITHIN 10 FEET OF EACH |
| | ROOM USED FOR SLEEPING PURPOSES. |
| | 2) PLEASE SHOW SMOKE ALARM LOCATIONS TO COMPLY WITH FBC |
| | R314.3 (SHOW SMOKE ALARM OUTSIDE OF MASTER RETREAT IN |
| | THE MASTER RETREAT VESTIBULE - SMOKE ALARM SHOULD NOT |
| | BE IN THE MASTER RETREAT BATH ROOM. |
| | 3) PLEASE SHOW A BATH/TOILET ROOM DOOR WIDTH OF A CLEAR |
| | OPENING OF 29 INCHES ON THE FIRST FLOOR TO COMPLY WITH |
| | FBC R320.1.1 - FBC ACCESSIBILITY 404.2.3 CLEAR WIDTH. |
| | CLEAR OPENINGS OF DOORWAYS WITH SWINGING DOORS SHALL BE |
| | MEASURED BETWEEN THE FACE OF THE DOOR AND THE STOP, |
| | WITH THE DOOR OPEN 90 DEGREES. |
| | 4) PLEASE SHOW THE GARAGE CEILING FIRE PROTECTION FROM |
| | HABITABLE ROOMS ABOVE THE GARAGE PER FBC R302.6 (5/8 |
| | TYPE X DRYWALL). |
| | 5) PLEASE SHOW THE REQUIRED DRYWALL UNDER THE ENCLOSED |
| | STAIR TO COMPLY WITH FBC R302.7 UNDER-STAIR PROTECTION. |
| | ENCLOSED SPACE UNDER STAIRS THAT IS ACCESSED BY A DOOR |
| | OR ACCESS PANEL SHALL HAVE WALLS, UNDER-STAIR SURFACE |
| | AND ANY SOFFITS PROTECTED ON THE ENCLOSED SIDE WITH |
| | 1/2-INCH (12.7 MM) GYPSUM BOARD. |
| | 6) PLEASE SHOW THE CEILING/FLOOR ASSEMBLY DRAFT |
| | STOPPING TO COMPLY WITH FBC R302.12 DRAFTSTOPPING. |
| | IN COMBUSTIBLE CONSTRUCTION WHERE THERE IS USABLE SPACE |
| | BOTH ABOVE AND BELOW THE CONCEALED SPACE OF A |
| | FLOOR-CEILING ASSEMBLY, DRAFTSTOPS SHALL BE INSTALLED |
| | SO THAT THE AREA OF THE CONCEALED SPACE DOES NOT EXCEED |
| | 1,000 SQUARE FEET (92.9 M2). DRAFTSTOPPING SHALL DIVIDE |
| | THE CONCEALED SPACE INTO APPROXIMATELY EQUAL AREAS. |
| | WHERE THE ASSEMBLY IS ENCLOSED BY A FLOOR MEMBRANE |
| | ABOVE AND A CEILING MEMBRANE BELOW, DRAFTSTOPPING SHALL |
| | BE PROVIDED IN FLOOR-CEILING ASSEMBLIES UNDER THE |
| | FOLLOWING CIRCUMSTANCES: |
| | 1.CEILING IS SUSPENDED UNDER THE FLOOR FRAMING. |
| | 2.FLOOR FRAMING IS CONSTRUCTED OF TRUSS-TYPE OPEN-WEB |
| | OR PERFORATED MEMBERS. |
| | 7) PLEASE SHOW THE FLAT ROOF FRAMING DETAILS - JOIST |
| | SIZE, SPACING AND ATTACHMENTS, STRAPPING ETC. |
| | 8) ALL PRODUCT APPROVALS PROVIDED NEED TO BE REVIEWED |
| | AND MARKED APPROVED BY THE BUILDING DESIGNER OF RECORD |
| | OR BE LISTED BY PRODUCT APPROVAL NUMBER ON THE |
| | DRAWINGS. |
| | 9) PRODUCT APPROVAL PROVIDED FOR THE METAL ROOFING |
| | SYSTEM (-89.4) DOES NOT MEET THE REQUIRED WIND DESIGN |
| | PRESSURES FOR ROOF WIND ZONES 3 (-99.22) - ROOF |
| | CLADDING DESIGN PRESSURES ARE NOT SHOWN ON THE DRAWINGS |
| | - WIND PRESSURES ARE BASED ON FBC TABLER301.2(2) |
| | 10) PLEASE PROVIDE A MIAMI DADE OR FLORIDA STATE |
| | PRODUCT APPROVAL FOR THE FLAT DECK ROOFING = PLEASE |
| | CIRCLE THE ROOFING SYSTEM TO BE USED IN THE PRODUCT |
| | APPROVAL - IF NEEDED PLEASE PROVIDE SIGNED AND SEALED |
| | ADDITIONAL ATTACHMENT DETAILS FROM AN ARCHITECT OR |
| | ENGINEER FOR THE ROOF ZONES 2 AND 3 WHICH MAY REQUIRE A |
| | HIGHER WIND PRESSURE - SEE NOTES ON THE PRODUCT |
| | APPROVAL. |
| | 11) PLEASE PROVIDE THE FLORIDA STATE PRODUCT APPROVAL |
| | FRONT PAGES FOR (DOOR - FL17347 AND METAL ROOF - |
| | FL11560.4). THE INSTALLATION INSTRUCTIONS HAVE BEEN |
| | PROVIDED. |
| | 12) ROOFING SYSTEM AND WINDOW AND DOOR PRODUCT |
| | APPROVALS MAY BE DEFERRED SUBMITTALS BY LISTING ITEMS |
| | TO BE DEFERRED ON THE CONSTRUCTION DOCUMENTS - |
| | 107.3.4.1 DEFERRED SUBMITTALS. FOR THE PURPOSES OF THIS |
| | SECTION, DEFERRED SUBMITTALS ARE DEFINED AS THOSE |
| | PORTIONS OF THE DESIGN THAT ARE NOT SUBMITTED AT THE |
| | TIME OF THE APPLICATION AND THAT ARE TO BE SUBMITTED TO |
| | THE BUILDING OFFICIAL WITHIN A SPECIFIED PERIOD. |
| | DEFERRAL OF ANY SUBMITTAL ITEMS SHALL HAVE THE PRIOR |
| | APPROVAL OF THE BUILDING OFFICIAL. THE REGISTERED |
| | DESIGN PROFESSIONAL IN RESPONSIBLE CHARGE SHALL LIST |
| | THE DEFERRED SUBMITTALS ON THE CONSTRUCTION DOCUMENTS |
| | FOR REVIEW BY THE BUILDING OFFICIAL. DOCUMENTS FOR |
| | DEFERRED SUBMITTAL ITEMS SHALL BE SUBMITTED TO THE |
| | REGISTERED DESIGN PROFESSIONAL IN RESPONSIBLE CHARGE |
| | WHO SHALL REVIEW THEM AND FORWARD THEM TO THE BUILDING |
| | OFFICIAL WITH A NOTATION INDICATING THAT THE DEFERRED |
| | SUBMITTAL DOCUMENTS HAVE BEEN REVIEWED AND FOUND TO BE |
| | IN GENERAL CONFORMANCE TO THE DESIGN OF THE BUILDING. |
| | THE DEFERRED SUBMITTAL ITEMS SHALL NOT BE INSTALLED |
| | UNTIL THE DEFERRED SUBMITTAL DOCUMENTS HAVE BEEN |
| | APPROVED BY THE BUILDING OFFICIAL. |
| | |
