| Date |
Text |
| 2020-11-30 16:29:28 | PLAN REVIEW / PLUMBING |
| | |
| | CHRISTOPHER S. THROOP, C.B.O. |
| | PLANS EXAMINER BUILDING - PX3169 |
| | PLANS EXAMINER 1&2 FAMILY - SFP306 |
| | CONSTRUCTION SERVICES DIVISION |
| | TEL: 561-805-6726 |
| | FAX: 561-805-6676 |
| | E-MAIL: [email protected] |
| | |
| | CODES IN EFFECT: |
| | 2017 FLORIDA BUILDING CODE, 6TH EDITION W/2017 WEST |
| | PALM BEACH AMENDMENTS TO THE FLORIDA BUILDING CODE, |
| | CHAPTER 1 ADMINISTRATION |
| | |
| | 1ST REVIEW |
| | |
| | RESULTS: DENIED |
| | ADDRESS THE ATTACHED COMMENTS AND RE-SUBMIT |
| | |
| | 1. PROVIDE SHOWER PAN DETAIL. |
| | |
| | P2709.1 SHOWER PAN CONSTRUCTION. FBC 107.2.1 |
| | WHERE A SHOWER RECEPTOR HAS A FINISHED CURB THRESHOLD, |
| | IT SHALL BE NOT LESS THAN 1 INCH (25 MM) BELOW THE |
| | SIDES AND BACK OF THE RECEPTOR. THE CURB SHALL BE NOT |
| | LESS THAN 2 INCHES (51 MM) AND NOT MORE THAN 9 INCHES |
| | (229 MM) DEEP WHEN MEASURED FROM THE TOP OF THE CURB TO |
| | THE TOP OF THE DRAIN. THE FINISHED FLOOR SHALL SLOPE |
| | UNIFORMLY TOWARD THE DRAIN NOT LESS THAN 1/4 UNIT |
| | VERTICAL IN 12 UNITS HORIZONTAL (2-PERCENT SLOPE) NOR |
| | MORE THAN 1/2 UNIT VERTICAL PER 12 UNITS HORIZONTAL |
| | (4-PERCENT SLOPE) AND FLOOR DRAINS SHALL BE FLANGED TO |
| | PROVIDE A WATER-TIGHT JOINT IN THE FLOOR. |
| | P2709.3 SHOWER PAN LINING INSTALLATION. |
| | LINING MATERIALS SHALL BE SLOPED ONE FOURTH UNIT |
| | VERTICAL IN 12 UNITS HORIZONTAL (2-PERCENT SLOPE) TO |
| | WEEP HOLES IN THE SUBDRAIN BY MEANS OF A SMOOTH, |
| | SOLIDLY FORMED SUBBASE, SHALL BE PROPERLY RECESSED AND |
| | FASTENED TO APPROVED BACKING SO AS NOT TO OCCUPY THE |
| | SPACE REQUIRED FOR THE WALL COVERING, AND SHALL NOT BE |
| | NAILED OR PERFORATED AT ANY POINT LESS THAN 1 INCH |
| | (25.4 MM) ABOVE THE FINISHED THRESHOLD. |
| | |
| | P2708.4SHOWER CONTROL VALVES. INDIVIDUAL SHOWER AND |
| | TUB/ SHOWER COMBINATION VALVES SHALL BE EQUIPPED WITH |
| | CONTROL VALVES OF THE PRESSURE-BALANCE, |
| | THERMOSTATIC-MIXING OR COMBINATION |
| | PRESSURE-BALANCE/THERMOSTATIC-MIXING VALVE TYPES WITH A |
| | HIGH LIMIT STOP IN ACCORDANCE WITH ASSE 1016/ASME |
| | A112.1016/CSA B125.16. THE HIGH LIMIT STOP SHALL BE SET |
| | TO LIMIT THE WATER TEMPERATURE TO NOT GREATER THAN |
| | 120?F (49?C). IN-LINE THERMOSTATIC VALVES SHALL NOT BE |
| | USED FOR COMPLIANCE WITH THIS SECTION. |
| | |
| | 2. PROVIDE WATER HAMMER DETAIL. IDENTIFY LOCATION ON |
| | PLAN. |
| | |
| | P2903.5WATER HAMMER. |
| | |
| | THE FLOW VELOCITY OF THE WATER DISTRIBUTION SYSTEM |
| | SHALL BE CONTROLLED TO REDUCE THE POSSIBILITY OF WATER |
| | HAMMER. WATER-HAMMER ARRESTORS SHALL BE INSTALLED IN |
| | ACCORDANCE WITH THE MANUFACTURER?S INSTRUCTIONS. |
| | WATER-HAMMER ARRESTORS SHALL CONFORM TO ASSE 1010. |
| | |
| | 3. P2708.4SHOWER CONTROL VALVES. |
| | |
| | INDIVIDUAL SHOWER AND TUB/ SHOWER COMBINATION VALVES |
| | SHALL BE EQUIPPED WITH CONTROL VALVES OF THE |
| | PRESSURE-BALANCE, THERMOSTATIC-MIXING OR COMBINATION |
| | PRESSURE-BALANCE/THERMOSTATIC-MIXING VALVE TYPES WITH A |
| | HIGH LIMIT STOP IN ACCORDANCE WITH ASSE 1016/ASME |
| | A112.1016/CSA B125.16. THE HIGH LIMIT STOP SHALL BE SET |
| | TO LIMIT THE WATER TEMPERATURE TO NOT GREATER THAN |
| | 120?F (49?C). IN-LINE THERMOSTATIC VALVES SHALL NOT BE |
| | USED FOR COMPLIANCE WITH THIS SECTION. |
| | |
| | |
| | |
| | |
| | WHEN RESUBMITING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. PLEASE, ADDITIONALLY, INSERT |
| | CORRECTED PAGES INTO SUBMITTAL AND LEAVE THE PREVIOUSLY |
| | REVIEWED SHEETS DETACHED. |
| | |
| | PLEASE NOTE THAT SUBMITTAL OF ADDITIONAL AND/OR REVISED |
| | MATERIALS MAY RESULT IN NEW PLAN REVIEW COMMENTS. |
| | |
| | |
| | |
