| Date |
Text |
| 2020-11-06 14:03:26 | 1ST REVIEW FBC-2017 PLUMBING |
| | PERMIT-20100983 |
| | 11/6/2020 |
| | |
| | CODES IN EFFECT: |
| | |
| | FBC P- FLORIDA PLUMBING CODE SIXTH EDITION 2017 |
| | FBC ACC- FLORIDA ACCESSIBILITY CODE SIXTH ADDITION 2017 |
| | FBC B- FLORIDA BUILDING CODE SIXTH EDITION 2017 |
| | FBC M- FLORIDA MECHANICAL CODE SIXTH EDITION 2017 |
| | FBC EC- FLORIDA ENERGY CONSERVATION CODE SIXTH EDITION |
| | 2017 |
| | FBC FG- FLORIDA FUEL GAS CODE SIXTH EDITION 2017 |
| | FBC EX- FLORIDA EXISTING BUILDING CODE SIXTH EDITION |
| | 2017 |
| | FS- FLORIDA STATUTES |
| | FAC- FLORIDA ADMINISTRATIVE CODE |
| | WPB- WEST PALM BEACH AMENDMENTS TO THE FBC SIXTH |
| | EDITION 2017 |
| | |
| | PLAN REVIEW RESULTS: DENIED. |
| | |
| | 1) PLEASE NOTE SEPARATE PERMITS ARE REQUIRED FOR THE |
| | WATER SERVICE BACKFLOW PREVENTER, IRRIGATION SYSTEM, |
| | GAS PIPING SYSTEM, EMERGENCY GENERATOR, AND GREASE |
| | INTERCEPTOR- SECTION 107.2.1 WPB. COMPLETE PLANS AND |
| | SPECIFICATIONS ARE REQUIRED FOR REVIEW. |
| | 2) PROVIDE A PLUMBING SUB-PERMIT APPLICATION- SECTION |
| | 105.1 WPB. |
| | |
| | 3) SHEET LS.1.1 PLUMBING FIXTURE REQUIREMENTS SCHEDULE |
| | CORRECTIONS PER SECTION 403 & TABLE 403.3 FBC P. |
| | |
| | A) ROUND UP THE FRACTIONAL NUMBERS- SECTION 403.1.1 FBC |
| | P. |
| | |
| | B) LIST THE REQUIRED AND PROVIDED NUMBERS OF MALE AND |
| | FEMALE WATER CLOSETS AND LAVATORIES FOR A3, B, R4, & S |
| | OCCUPANCIES. PLEASE NOTE THAT SEPARATE MALE AND FEMALE |
| | FIXTURES ARE REQUIRED FOR A3, B AND S OCCUPANCIES- |
| | SECTION 403.2. UNISEX ARE PERMITTED FOR THE R4 |
| | OCCUPANCY. |
| | |
| | C) LIST THE REQUIRED AND PROVIDED NUMBER OF SERVICE |
| | SINKS AND DRINKING FOUNTAINS- TABLE 403.3 FBC P. |
| | |
| | 4) SHEET P2.1: PROVIDE A CLEANOUT AT THE JUNCTION OF |
| | THE BUILDING DRAIN AND SEWER- SECTION 708.1.3 FBC P. |
| | |
| | 5) SHEETS P2.1 & P5.1: THE PLAN INDICATES ISLAND SINKS |
| | AND DISHWASHER BUT THE ISOMETRIC DRAWING SHOWS A VENT |
| | STACK INSTEAD OF AN ISLAND VENT OR AAV- SECTION 916 FBC |
| | P. |
| | |
| | 6) P0.1, P2.1 & P5.1: A) SK-1 &SK-2 ARE MISLABELED L2 |
| | IN THE ISOMETRIC. B) SK-3 IS MISLABELED SK-2 IN THE |
| | ISOMETRIC. C) SK-3 IS A 3-COMPARTMENT SINK PER THE |
| | FIXTURE SCHEDULE BUT IS SHOWN AS A 2-COMPARTMENT SINK |
| | ON THE PLAN, AND A SINGLE SINK IN THE ISO. |
| | |
| | 7) P0.1 PLUMBING FIXTURE SCHEDULE: PLEASE INCLUDE THE |
| | SHOWER VALVES TO BE INSTALLED IN THE ACCESSIBLE AND |
| | NON-ACCESSIBLE SHOWERS- SECTION 608.6 FBC ACC AND 424.3 |
| | FBC P. |
| | |
| | 8) P0.1: PROVIDE AN ITEMIZED FOOD EQUIPMENT PLAN AND |
| | CORRELATING EQUIPMENT SCHEDULE- SECTION 107.2.1 WPB. |
| | CLARIFY WHAT EQUIPMENT MAY BE INSTALLED IN THE KITCHEN |
| | SUCH AS A FOOD WASTE DISPOSER, ICE MAKER, BEVERAGE |
| | DISPENSER, COFFEE MAKER ETC. |
| | |
| | 9) P0.1, P2.1 & P5.1: PROVIDE A GREASE INTERCEPTOR AND |
| | GREASE INTERCEPTOR CALCULATIONS FOR THE DRAINAGE FROM |
| | PLUMBING FIXTURES IN THE KITCHEN- REFER TO SECTIONS |
| | 1003.1 & 1003.3.1 FBC P. REVISE THE DRAWINGS AND |
| | SPECIFICATIONS TO SHOW THE TYPE OF INTERCEPTOR TO BE |
| | INSTALLED, MAKE AND MODEL OF THE UNIT, THE LOCATION AND |
| | THE PLUMBING PIPING REQUIREMENTS. |
| | |
| | 10) P0.1, P2.1 & P5.1: THE DRAINAGE FROM THE DISHWASHER |
| | AND THE 2 OR 3-COMPARTMENT SINKS SHALL DISCHARGE |
| | THROUGH AN INDIRECT WASTE RECEPTOR- SECTIONS 802.1 & |
| | 802.7 FBC P. REVISE THE DRAWINGS ACCORDINGLY, PROVIDE |
| | AN INSTALLATION DETAIL PER SECTION 802.2, AND ADD THE |
| | RECEPTORS TO THE FIXTURE SCHEDULES- SECTION 802.3. |
| | |
| | 11) P0.1, P2.1 & P5.1: PROVIDE INTERCEPTORS FOR THE |
| | CLOTHES WASHERS PER SECTION 1003.6. REVISE THE DRAWINGS |
| | AND SPECIFICATIONS TO SHOW MAKES AND MODELS OF THE |
| | UNITS, LOCATIONS, AND THE PLUMBING PIPING REQUIREMENTS. |
| | |
| | 12) P3.1 & P6.1: A) SK-3 IS MISLABELED SK-2 IN THE |
| | ISOMETRIC. B) SK-3 IS A 3-COMPARTMENT SINK PER THE |
| | FIXTURE SCHEDULE BUT IS SHOWN AS A 2-COMPARTMENT SINK |
| | ON THE PLAN, AND A SINGLE SINK IN THE ISO. C) P3.1 |
| | SHOWS SK-1 & SK-2 COUNTER SINKS, P6.1 SHOWS DOUBLE SK-1 |
| | SINKS. |
| | |
| | 13) P0.1, P5.1, & P6.1: SK-4 IS MISLABELED AS SK-1 IN |
| | THE ISOMETRIC DRAWINGS- SECTION 107.2.1 WPB. BASED ON |
| | THE USE OF THE MEDICATION ROOM, A CLINICAL SINK SHALL |
| | BE REQUIRED IN ACCORDANCE WITH SECTIONS 422.1 & 422.6. |
| | REVISE THE DRAWINGS AND THE SCHEDULE ACCORDINGLY. |
| | |
| | 14) P3.1 & P6.1: IF APPLICABLE TO THE KITCHEN LAYOUT |
| | PLEASE SHOW THE WATER SUPPLY LINES TO EQUIPMENT SUCH AS |
| | ICE MAKERS OR BEVERAGE DISPENSERS AND THE REQUIRED |
| | WATER HAMMER ARRESTORS AND BACKFLOW PREVENTERS- |
| | SECTIONS 604.9 AND 608.3 FBC P. SHOW HOW THE DISHWASHER |
| | WILL BE PROTECTED AGAINST BACKFLOW- SECTION 409.2. |
| | |
| | 15) P3.1 & P6.1: INDICATE HOW TEMPERED WATER WILL BE |
| | PROVIDED TO THE LAVATORIES- SECTIONS 416.5 & 607.1.2. |
| | |
| | 16) P0.1: PROVIDE A PLUMBING DEVICE SCHEDULE INDICATING |
| | MAKES AND MODELS AND LISTINGS OF THE RECIRCULATION |
| | PUMPS, BALANCING VALVES, FULL OPEN SHUTOFF VALVES, |
| | WATER HAMMER ARRESTORS, TRAP PRIMERS, BACKFLOW |
| | PREVENTERS, AND MIXING VALVES ETC.- SECTIONS 604.9, |
| | 606, 607.1.2, 607.2.1, 608.3, 613.1 FBC P AND 107.2.1 |
| | WPB. |
| | |
| | 17) P3.1: INDICATE HOW ACCESS WILL BE PROVIDED TO THE |
| | BALANCING VALVES- SECTION 606.3. |
| | |
| | 18) P0.1 & P3.1: SHOW WATER HEATER RELIEF VALVE PIPE, |
| | DRAIN PAN AND DRAIN PIPE DETAILS- SECTION 504 FBC P. |
| | |
| | 19) P0.1 & P3.1: INDICATE THE RECIRCULATION PUMP |
| | CONTROLS SHALL START THE PUMPS BASED ON THE |
| | IDENTIFICATION OF A DEMAND FOR HOT WATER WITHIN THE |
| | OCCUPANCY, AND SHALL AUTOMATICALLY TURN OFF THE PUMP |
| | WHEN THE WATER IN THE CIRCULATION LOOP IS AT THE |
| | DESIRED TEMPERATURE AND WHEN THERE IS NO DEMAND FOR HOT |
| | WATER- SECTION 607.2.1 FBC P AND SECTION R403.5.1.1 FBC |
| | EC. |
| | |
| | 20) CORRECT THE ENERGY COMPLIANCE IECC- 2015 FORM |
| | INDICATING THE WATER HEATER IS LESS THAN 75000 BTUH- |
| | THE EQUIPMENT SCHEDULE INDICATES 200,000 BTUH. PLEASE |
| | CORRECT THE DATA, AND PROVIDE THE MISSING PIPING SYSTEM |
| | COMPLIANCE DATA- SECTION C101.5 FBC EC. |
| | |
| | 21) PROVIDE A ROOF DRAINAGE PLAN INCLUDING ROOF FLOW |
| | RATE CALCULATIONS, AND SIZING OF THE HORIZONTAL ROOF |
| | GUTTER AND VERTICAL LEADER SIZES PER SECTIONS 1106.3, |
| | 1106.6 AND TABLES 1106.3 & 1106.6 FBC P. |
| | |
| | 22) SHEETS A10.01- A10.02 FAIR HOUSING ACT DESIGN |
| | MANUAL GUIDELINES: |
| | |
| | A) PROVIDE GRAB BAR REINFORCEMENT DETAILS FOR ALL BATH |
| | FIXTURES- PAGE 7.33 (REQUIREMENT 6). PLEASE NOTE |
| | SPECIFICATION TYPE B SHOWERS REQUIRE REINFORCEMENTS FOR |
| | FUTURE SEATS- PAGE 7.58. |
| | |
| | B) INDICATE WHICH DESIGN HAS BEEN SELECTED FOR THE |
| | RESIDENT ROOMS- SPECIFICATION TYPE A OR TYPE B- PAGE |
| | 7.34. |
| | |
| | C) THE SHOWERS SHALL NOT BE INSTALLED ADJACENT TO THE |
| | TOILETS- PAGE 7.44. PLEASE RE-DESIGN THE LAYOUT TO BE |
| | IN COMPLIANCE. |
| | |
| | D) THE SHOWER CONTROLS SHALL BE INSTALLED ON THE |
| | OPPOSITE WALL OF WHERE THEY ARE SHOWN ON THE PLAN- PAGE |
| | 7.56. |
| | |
| | E) SHOW THE REQUIRED MINIMUM 36 X 36 IN. SHOWER |
| | DIMENSIONS- PAGE 7.58. |
| | |
| | F) PROVIDE THE CLEAR FLOOR SPACE DIAGRAMS AND |
| | DIMENSIONS FOR THE TOILETS- PAGE 7.43- 7.46. |
| | |
| | G) A FRONT APPROACH TO THE LAVATORY SINKS IS SHOWN |
| | PROVIDE A DETAIL FOR INSTALLATION OF THE REMOVABLE |
| | LAVATORY CABINET OR BASE- PAGE 7.49. |
| | |
| | 23) SHEET A10.0.3: |
| | |
| | A) PROVIDE THE CLEAR FLOOR SPACE DIMENSION FOR THE |
| | WATER CLOSET MEASURED PERPENDICULAR FROM THE REAR WALL- |
| | SECTION 604.3.1 FBC ACC. |
| | |
| | B) SHOW THE MOUNTING HEIGHTS OF FIXTURE GRAB BARS |
| | MEASURED FROM THE FINISH FLOORS TO THE TOPS OF THE |
| | GRIPPING SURFACES- SECTION 609.4 |
| | |
| | C) SHOW THE LOCATIONS OF THE WATER CLOSET FLUSH |
| | CONTROLS- SECTION 604.6. |
| | |
| | D) THE LENGTHS OF THE SHOWER GRAB BARS AS SHOWN IN |
| | DETAILS 2, 9, & 10 ARE NOT IN COMPLIANCE WITH FIGURE |
| | 608.3.1 FBC ACC. |
| | |
| | E) THE CONTROLS, FAUCETS, AND SHOWER SPRAY UNIT SHALL |
| | BE LOCATED ON THE CONTROL WALL 15 INCHES MAXIMUM FROM |
| | THE CENTERLINE OF THE SEAT TOWARD THE SHOWER OPENING. |
| | PLEASE CORRECT THE INCORRECT DIMENSION SHOWN IN DETAIL |
| | 9- SECTION 608.5.1. |
| | |
| | F) CORRECT THE 1/8 IN. SHOWER SLOPE SHOWN IN THE DETAIL |
| | TO INDICATE 1/4 IN. PER FT.- SECTION 417.5.2 FBC P. |
| | SHOW THE LINER TURNED UP NOT LESS THAN 2? ABOVE THE |
| | FINISHED THRESHOLD ON ALL SIDES. PLEASE NOTE THAT |
| | RECESSED SHOWERS SHALL BE DEPRESSED A MINIMUM OF 2 IN. |
| | BELOW THE FINISHED FLOOR. |
| | |
| | 24) A10.04: SHOW THE CLEAR FLOOR SPACE DIAGRAMS AND |
| | DIMENSIONS AT THE KITCHEN SINKS- SECTION 606.2 FBC ACC. |
| | |
| | 25) A10.05: SHOW THE REQUIRED CLEAR FLOOR SPACE |
| | PARALLEL APPROACHES FOR THE WASHERS AND DRYERS- SECTION |
| | 611.2. A) SHOW THE MEASUREMENTS TO THE BOTTOM AND TOP |
| | OF THE WASHER AND DRYER DOOR OPENINGS MEASURED FROM THE |
| | FINISHED FLOOR- SECTION 611.4 FBC ACC. C) INDICATE THE |
| | WASHER AND DRYER CONTROLS ARE IN COMPLIANCE WITH |
| | SECTIONS 309.3, 309.4 & 611.3 FBC ACC. |
| | |
| | 26) A10.06: |
| | |
| | A) SHOW THE MOUNTING HEIGHTS OF FIXTURE GRAB BARS |
| | MEASURED FROM THE FINISH FLOORS TO THE TOPS OF THE |
| | GRIPPING SURFACES- SECTION 609.4 FBC ACC. |
| | |
| | B) SHOW THE LOCATIONS OF THE WATER CLOSET FLUSH |
| | CONTROLS- SECTION 604.6. |
| | |
| | C) SHOW THE KNEE CLEARANCE AT THE UNDERSIDE OF THE |
| | LAVATORY SINKS- SECTION 306.3. |
| | |
| | D) THE TOILET PAPER DISPENSER SHALL BE INSTALLED WITH |
| | THE CENTERLINE OF THE DISPENSER LOCATED BETWEEN 7 AND 9 |
| | IN. FROM THE FRONT OF THE WATER CLOSET- SECTION 604.7. |
| | |
| | E) SEE COMMENT #13 REGARDING THE MEDICATION SINK. |
| | PLEASE SHOW THE CLEAR FLOOR SPACE DIAGRAM AND |
| | DIMENSIONS FOR THE SINK IN DETAIL 1- SECTIONS 212.3 AND |
| | 606.2. |
| | 27) A10.0.7: |
| | |
| | A) SHOW THE REQUIRED 30 X 60 IN. DIMENSIONS OF THE |
| | SHOWERS- SECTION AND FIGURE 608.2.2 FBC ACC. |
| | |
| | B) SHOW THE REQUIRED 30 X 60 IN. CLEARANCE DIAGRAMS AND |
| | DIMENSIONS AT THE SHOWERS- SECTION 608.2.2.1. |
| | |
| | C) SHOW THE SHOWER GRAB BARS WILL BE INSTALLED A |
| | MAXIMUM OF 6 IN. FROM THE ADJACENT WALLS- SECTION AND |
| | FIGURE 608.3.2. |
| | |
| | D) SHOW THE HEIGHT OF THE SHOWER CONTROL MEASURED FROM |
| | THE FINISHED FLOOR OF THE SHOWER- SECTION 608.5.2. |
| | |
| | E) PROVIDE A ROLL-IN SHOWER PAN AND THRESHOLD DETAIL- |
| | SECTION 608.7 FBC P AND SECTION 417.5.2 FBC P. |
| | |
| | F) SHOW THE LOCATIONS OF THE WATER CLOSET FLUSH |
| | CONTROLS- SECTION 604.6 FBC ACC. |
| | |
| | G) SHOW THE KNEE CLEARANCE AT THE UNDERSIDE OF THE |
| | LAVATORY SINKS- SECTION 306.3. |
| | |
| | H) THE TOILET PAPER DISPENSER SHALL BE INSTALLED WITH |
| | THE CENTERLINE OF THE DISPENSER LOCATED BETWEEN 7 AND 9 |
| | IN. FROM THE FRONT OF THE WATER CLOSET- SECTION 604.7. |
| | |
| | 28) ACCESSIBLE DRINKING FOUNTAINS: PROVIDE DRAWINGS AND |
| | DETAILS SHOWING: A) THE 30 X 48 IN. CLEAR FLOOR SPACE |
| | FOR A FORWARD APPROACH TO THE WHEELCHAIR ACCESSIBLE |
| | DRINKING FOUNTAIN- SECTION 602.2 FBC ACC. B) KNEE AND |
| | TOE CLEARANCES, SPOUT HEIGHTS, SPOUT LOCATIONS- |
| | SECTIONS 306, 307, & 602.2. C) COMPLIANCE WITH SECTION |
| | 307.2 PROTRUSION LIMITS. |
| | |
| | WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. |
| | |
| | CHRISTOPHER L. COLE |
| | MECHANICAL/PLUMBING PLANS EXAMINER |
| | 401 CLEMATIS STREET |
| | WEST PALM BEACH FL 33401 |
| | 561-805-6719 |
| | [email protected] |
| | |
