| Date |
Text |
| 2018-10-03 11:46:54 | 1ST REVIEW FBC-2010 MECHANICAL |
| | PERMIT #18080002 |
| | 10/3/2018 |
| | |
| | CODES IN EFFECT: |
| | |
| | FBC B- FLORIDA BUILDING CODE- 2010 |
| | FBC M- FLORIDA MECHANICAL CODE- 2010 |
| | FBC EC- FLORIDA ENERGY CONSERVATION CODE- 2010 |
| | FBC FG- FLORIDA FUEL GAS CODE- 2010 |
| | FS- FLORIDA STATUTES |
| | FAC- FLORIDA ADMINISTRATIVE CODE |
| | WPB- WEST PALM BEACH AMENDMENTS TO THE FBC 2010 |
| | |
| | PLAN REVIEW RESULTS: DENIED. |
| | |
| | 1) PROVIDE MINIMUM VENTILATION CALCULATIONS FOR ALL |
| | ROOMS AND SPACES, INCLUDING THE REQUIRED O/A AND THE |
| | EXHAUST. |
| | |
| | 2) SUBMIT AC COOLING AND HEATING CALCULATIONS FOR THE |
| | NEW HEAT PUMPS- SECTION 503.2.1 FBC EC. |
| | |
| | 3) SUBMIT AN ENERGY EFFICIENCY COMPLIANCE REPORT IN |
| | ACCORDANCE WITH SECTIONS 101.5 AND 501.2 FBC EC. |
| | |
| | 4) SHEETS M100 & M101: SMOKE DETECTORS REQUIRED IN THE |
| | RETURN AIR PLENUM- SECTION 606.2.2 FBC M. PLEASE |
| | PROVIDE A DETECTOR IN EACH HP CLOSER TO MEET THE |
| | REQUIREMENT. A) INDICATE THE CONTROLS OPERATION FOR THE |
| | DETECTORS RELATING TO THE SHUTDOWN OF THE HP'S, AND HOW |
| | THE DETECTORS WILL BE SUPERVISED- SECTIONS 606.4 & |
| | 606.4.1 FBC M. |
| | |
| | 5) M100: IDENTIFY THE HP LOCATED IN THE CLOSET BY HALL |
| | 135- SECTION 107.2.1 WPB. |
| | |
| | 6) M101: PLEASE REVIEW SECTION 504.8 FBC M PRINTED |
| | BELOW AND REVISE THE PLANS AND DETAILS TO SHOW |
| | COMPLIANCE. PROVIDE SUBMITTALS FOR THE KITCHEN HOOD, |
| | EXHAUST FAN, AND EXHAUST DUCT. |
| | |
| | 504.8 COMMON EXHAUST SYSTEMS FOR DOMESTIC KITCHENS |
| | LOCATED IN MULTISTORY STRUCTURES. |
| | |
| | WHERE A COMMON MULTISTORY DUCT SYSTEM IS DESIGNED AND |
| | INSTALLED TO CONVEY EXHAUST FROM MULTIPLE DOMESTIC |
| | KITCHEN EXHAUST SYSTEMS, THE CONSTRUCTION OF THE SYSTEM |
| | SHALL BE IN ACCORDANCE WITH ALL OF THE FOLLOWING: |
| | |
| | 1.THE SHAFT IN WHICH THE DUCT IS INSTALLED SHALL BE |
| | CONSTRUCTED AND FIRE-RESISTANCE RATED AS REQUIRED BY |
| | THE FLORIDA BUILDING CODE, BUILDING. |
| | |
| | 2.DAMPERS SHALL BE PROHIBITED IN THE EXHAUST DUCT, |
| | EXCEPT AS SPECIFIED IN SECTION 505.1. PENETRATIONS OF |
| | THE SHAFT AND DUCTWORK SHALL BE PROTECTED IN ACCORDANCE |
| | WITH SECTION 607.5.5, EXCEPTION 2. |
| | |
| | 3.RIGID METAL DUCTWORK SHALL BE INSTALLED WITHIN THE |
| | SHAFT TO CONVEY THE EXHAUST. THE DUCTWORK SHALL BE |
| | CONSTRUCTED OF SHEET STEEL HAVING A MINIMUM THICKNESS |
| | OF 0.0187 INCH (0.4712 MM) (NO. 26 GAGE) AND IN |
| | ACCORDANCE WITH SMACNA DUCT CONSTRUCTION STANDARDS. |
| | |
| | 4.THE DUCTWORK WITHIN THE SHAFT SHALL BE DESIGNED AND |
| | INSTALLED WITHOUT OFFSETS. |
| | |
| | 5.THE EXHAUST FAN MOTOR DESIGN SHALL BE IN ACCORDANCE |
| | WITH SECTION 503.2. |
| | |
| | 6. THE EXHAUST FAN MOTOR SHALL BE LOCATED OUTSIDE OF |
| | THE AIRSTREAM. |
| | |
| | 7.THE EXHAUST FAN SHALL RUN CONTINUOUSLY, AND SHALL BE |
| | CONNECTED TO A STANDBY POWER SOURCE. |
| | |
| | 8. EXHAUST FAN OPERATION SHALL BE MONITORED IN AN |
| | APPROVED LOCATION AND SHALL INITIATE AN AUDIBLE OR |
| | VISUAL SIGNAL WHEN THE FAN IS NOT IN OPERATION. |
| | |
| | 9.WHERE THE EXHAUST RATE FOR AN INDIVIDUAL KITCHEN |
| | EXCEEDS 400 CFM (0.19 M3/S) MAKEUP AIR SHALL BE |
| | PROVIDED IN ACCORDANCE WITH SECTION 505.2. |
| | |
| | 10.A CLEANOUT OPENING SHALL BE LOCATED AT THE BASE OF |
| | THE SHAFT TO PROVIDE ACCESS TO THE DUCT TO ALLOW FOR |
| | CLEANOUT AND INSPECTION. THE FINISHED OPENINGS SHALL BE |
| | NOT LESS THAN 12 INCHES BY 12 INCHES (305 MM BY 305 |
| | MM). |
| | |
| | 11.SCREENS SHALL NOT BE INSTALLED AT THE TERMINATION. |
| | |
| | 12.THE COMMON MULTISTORY DUCT SYSTEM SHALL SERVE ONLY |
| | KITCHEN EXHAUST AND SHALL BE INDEPENDENT OF OTHER |
| | EXHAUST SYSTEMS. |
| | |
| | 7) PROVIDE A CALCULATION TABLE ON THE PLAN SHOWING THE |
| | TOTAL LENGTH OF THE DRYER EXHAUST DUCT RUN, AND THE |
| | MAXIMUM ALLOWABLE RUN DISTANCE PER THE MANUFACTURER'S |
| | SPECIFICATIONS-- SECTIONS 504.6.4.1 & 506.4.2 FBC M. |
| | |
| | 8) PROVIDE CONSTRUCTION DETAILS FOR THE DRYER EXHAUST |
| | DUCT ENCLOSURE AND VERIFY THAT THE EQUIVALENT LENGTH OF |
| | THE EXHAUST DUCT SHALL BE INDENTIFIED ON A PERMANENT |
| | LABEL OR TAG- SECTION 504.6.5 FBC M. |
| | |
| | 9) PROVIDE DETAILS FOR THE TOILET, DRYER, AND KITCHEN |
| | SUBDUCTS. |
| | |
| | 10) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE DRYER, |
| | THE COOKING APPLIANCES, THE WALK-IN COOLER, AND THE |
| | FIREPLACE. |
| | |
| | 11) SHOW THE LOCATION OF THE WALK-IN COOLER CONDENSER |
| | AND PROVIDE ENGINEERING FOR INSTALLATION- SECTION |
| | 301.12 FBC M. |
| | |
| | |
| | WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. ADDITIONALLY, PLEASE INSERT |
| | CORRECTED PLAN SHEETS INTO THE SETS, REMOVE THE |
| | PREVIOUSLY REVIEWED SHEETS AND MARK VOID ON THEM, AND |
| | KEEP THEM WITH THE SUBMITTALS. |
| | |
| | CHRISTOPHER L. COLE |
| | MECHANICAL PLANS EXAMINER |
| | 401 CLEMATIS STREET |
| | WEST PALM BEACH FL 33401 |
| | 561-805-6719 |
| | [email protected] |
| | |
