| Date |
Text |
| 2018-02-15 14:32:31 | 1ST REVIEW: FBC 2017 6TH EDITION |
| | |
| | PLUMBING COMMENTS: |
| | |
| | 1. PROVIDE OCCUPANT LOAD PLUMBING FIXTURE COUNT |
| | BREAKDOWN FOR EMPLOYEES, VISITORS AND PATIENTS. PER FBC |
| | TABLE 403.1 |
| | |
| | 2. WHAT TYPE OF FACILITY IS THIS GOING TO BE. PER WPB |
| | AMEND TO FBC 107.2.1 |
| | |
| | 3. SHOW COMPLIANCE WITH FBC ACC 610.3 SHOWER |
| | COMPARTMENT SEATS. |
| | WHERE A SEAT IS PROVIDED IN A STANDARD ROLL-IN SHOWER |
| | COMPARTMENT, IT SHALL BE A FOLDING TYPE, SHALL BE |
| | INSTALLED ON THE SIDE WALL ADJACENT TO THE CONTROLS, |
| | AND SHALL EXTEND FROM THE BACK WALL TO A POINT WITHIN 3 |
| | INCHES (75 MM) OF THE COMPARTMENT ENTRY. WHERE A SEAT |
| | IS PROVIDED IN AN ALTERNATE ROLL-IN TYPE SHOWER |
| | COMPARTMENT, IT SHALL BE A FOLDING TYPE, SHALL BE |
| | INSTALLED ON THE FRONT WALL OPPOSITE THE BACK WALL, AND |
| | SHALL EXTEND FROM THE ADJACENT SIDE WALL TO A POINT |
| | WITHIN 3 INCHES (75 MM) OF THE COMPARTMENT ENTRY. IN |
| | TRANSFER-TYPE SHOWERS, THE SEAT SHALL EXTEND FROM THE |
| | BACK WALL TO A POINT WITHIN 3 INCHES (75 MM) OF THE |
| | COMPARTMENT ENTRY. THE TOP OF THE SEAT SHALL BE 17 |
| | INCHES (430 MM) MINIMUM AND 19 INCHES (485 MM) MAXIMUM |
| | ABOVE THE BATHROOM FINISH FLOOR. SEATS SHALL COMPLY |
| | WITH 610.3.1 OR 610.3.2. |
| | |
| | 4. GRAB BARS SHALL BE FROM FINISH FLOOR MEASURED TO THE |
| | TOP OF THE GRIPPING SURFACE. PER FBC ACC 609.4 |
| | |
| | 5. PROVIDE THE DIMENSIONS FOR SHOWER ON EXTERIOR WALL |
| | IN BATHROOM 5+6. 901.2.1 |
| | |
| | 6. SHOW COMPLIANCE WITH FBC ACC |
| | 608.5.1 TRANSFER TYPE SHOWER COMPARTMENTS. |
| | IN TRANSFER TYPE SHOWER COMPARTMENTS, THE CONTROLS, |
| | FAUCETS, AND SHOWER SPRAY UNIT SHALL BE INSTALLED ON |
| | THE SIDE WALL OPPOSITE THE SEAT 38 INCHES (965 MM) |
| | MINIMUM AND 48 INCHES (1220 MM) MAXIMUM ABOVE THE |
| | SHOWER FLOOR AND SHALL BE LOCATED ON THE CONTROL WALL |
| | 15 INCHES (380 MM) MAXIMUM FROM THE CENTERLINE OF THE |
| | SEAT TOWARD THE SHOWER OPENING. |
| | 608.5.2 STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS. |
| | IN STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS, THE |
| | CONTROLS, FAUCETS, AND SHOWER SPRAY UNIT SHALL BE |
| | LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48 |
| | INCHES (1220 MM) ABOVE THE SHOWER FLOOR. WHERE A SEAT |
| | IS PROVIDED, THE CONTROLS, FAUCETS, AND SHOWER SPRAY |
| | UNIT SHALL BE INSTALLED ON THE BACK WALL ADJACENT TO |
| | THE SEAT WALL AND SHALL BE LOCATED 27 INCHES (685 MM) |
| | MAXIMUM FROM THE SEAT WALL. |
| | |
| | 7. SHOW COMPLIANCE WITH FBC ACC 608.3.1 TRANSFER TYPE |
| | SHOWER COMPARTMENTS. |
| | IN TRANSFER TYPE COMPARTMENTS, GRAB BARS SHALL BE |
| | PROVIDED ACROSS THE CONTROL WALL AND BACK WALL TO A |
| | POINT 18 INCHES (455 MM) FROM THE CONTROL WALL. |
| | |
| | 8. THE SHOWER IN BATHROOM 7+8 SHALL BE VENTED BEFORE IT |
| | CONNECTS TO THE BUILDING DRAIN. PER FBC PL 901.2.1 |
| | |
| | 9. THE DETAILS FOR THE GREASE INTERCEPTOR SHALL COMPLY |
| | WITH WPB UTILITIES DEPT STANDARD DETAIL GS-7 |
| | |
| | 10. PROVIDE DETAIL FOR THE SHOWER PANS. 901.2.1 |
| | |
| | |
| | |
| | PLEASE NOTE THAT SUBMITTAL OF ADDITIONAL AND/OR REVISED |
| | MATERIALS MAY RESULT IN NEW PLAN REVIEW COMMENTS. |
| | WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE |
| | LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY |
| | RE-SUBMITTAL FORM. PLEASE, ADDITIONALLY, INSERT |
| | CORRECTED PAGES INTO TO SUBMITTAL AND REMOVE OR VOID |
| | THE PREVIOUSLY REVIEWED SHEETS. |
| | |
| | GEORGE JOHNSON |
| | PLUMBING PLANS EXAMINER |
| | CITY OF WEST PALM BEACH |
| | 561-805-6711 |
| | [email protected] |
| | |
