| Date |
Text |
| 2017-06-15 16:44:36 | CODES IN EFFECT: |
| | FLORIDA BUILDING CODE 2014 5TH EDITION |
| | FLORIDA BUILDING CODE ENERGY CONSERVATION 2014 5TH ED |
| | NFPA 70 2011 EDITION |
| | |
| | JAKE LEAHY |
| | ELECTRICAL PLANS EXAMINER II |
| | 561-805-6713 |
| | [email protected] |
| | |
| | |
| | |
| | 210.8 GROUND-FAULT CIRCUIT-INTERRUPTER PROTECTION |
| | FOR PERSONNEL |
| | |
| | (A) DWELLING UNITS. ALL 125-VOLT, SINGLE-PHASE, 15- AND |
| | 20-AMPERE RECEPTACLES INSTALLED IN THE LOCATIONS |
| | SPECIFIED |
| | IN 210.8(A)(1) THROUGH (10) SHALL HAVE GROUND-FAULT |
| | CIRCUI T |
| | INTERRUPTER PROTECTION FOR PERSONNEL. |
| | (7) SINKS ? WHERE RECEPTACLES ARE INSTALLED WITHIN 1.8 |
| | M |
| | (6 FT) OF THE OUTSIDE EDGE OF THE SINK |
| | |
| | 210.52 DWELLING UNIT RECEPTACLE OUTLETS |
| | |
| | (A) GENERAL PROVISIONS. IN EVERY KITCHEN, FAMILY ROOM, |
| | DINING |
| | ROOM, LIVING ROOM, PARLOR, LIBRARY, DEN, SUNROOM, |
| | BEDROOM, RECREATION |
| | ROOM, OR SIMILAR ROOM OR AREA OF DWELLING UNITS, |
| | RECEPTACLE |
| | OUTLETS SHALL BE INSTALLED IN ACCORDANCE WITH THE |
| | GENERAL PROVISIONS |
| | SPECIFIED IN 210.52(A)(1) THROUGH (A)(4). |
| | |
| | (1) SPACING. RECEPTACLES SHALL BE INSTALLED SUCH THAT |
| | NO POINT |
| | MEASURED HORIZONTALLY ALONG THE FLOOR LINE OF ANY WALL |
| | SPACE IS |
| | MORE THAN 1.8 M (6 FT) FROM A RECEPTACLE OUTLET. |
| | |
| | (2) WALL SPACE. AS USED IN THIS SECTION, A WALL SPACE |
| | SHALL |
| | INCLUDE THE FOLLOWING: |
| | (1) ANY SPACE 600 MM (2 F T) OR MORE IN WIDTH |
| | (INCLUDING SPACE |
| | MEASURED AROUND CORNERS) AND UNBROKEN ALONG THE FLOOR |
| | LINE BY DOORWAYS AND SIMILAR OPENINGS, FIREPLACES, AND |
| | FIXED CABINETS |
| | (2) THE SPACE OCCUPIED BY FIXED PANELS IN EXTERIOR |
| | WALLS, |
| | EXCLUDING SLIDING PANELS |
| | (3) THE SPACE AFFORDED BY FIXED ROOM DIVIDERS, SUCH AS |
| | FREESTANDING |
| | BAR-TYPE COUNTERS OR RAILINGS |
| | |
| | |
| | 408. 4 FIELD IDENTIFICATION REQUIRED |
| | (A) CIRCUIT DIRECTORY OR CIRCUIT IDENTIFICATION. EVERY |
| | CIRCUIT |
| | AND CIRCUIT MODIFICATION SHALL BE LEGIBLY IDENTIFIED AS |
| | TO |
| | ITS CLEAR, EVIDENT, AND SPECIFIC PURPOSE OR USE. THE |
| | IDENTIFICATION |
| | SHALL INCLUDE AN APPROVED DEGREE OF DETAIL THAT ALLOWS |
| | EACH CIRCUIT TO BE DISTINGUISHED FROM ALL OTHERS. SPARE |
| | POSITIONS |
| | THAT CONTAIN UNUSED OVERCURRENT DEVICES OR SWITCHES |
| | SHALL BE |
| | DESCRIBED ACCORDINGLY. THE IDENTIFICATION SHALL BE |
| | INCLUDED IN |
| | A CIRCUIT DIRECTORY THAT IS LOCATED ON THE FACE OR |
| | INSIDE OF THE |
| | PANEL DOOR IN THE CASE OF A PANELBOARD AND AT EACH |
| | SWITCH OR |
| | CIRCUIT BREAKER IN A SWITCHBOARD OR SWITCHGEAR. NO |
| | CIRCUIT SHALL |
| | BE DESCRIBED IN A MANNER THAT DEPENDS ON TRANSIENT |
| | CONDITIONS |
| | OF OCCUPANCY. |
