| Date |
Text |
| 2017-05-23 17:31:28 | CODES IN EFFECT: |
| | FLORIDA BUILDING CODE 2014 5TH EDITION |
| | FLORIDA BUILDING CODE ENERGY CONSERVATION 2014 5TH |
| | EDITION |
| | NFPA 70 2011 EDITION |
| | |
| | JAKE LEAHY |
| | ELECTRICAL PLANS EXAMINER II |
| | 561-805-6713 |
| | [email protected] |
| | |
| | |
| | THE FOLLOWING INFORMATION NEEDS TO PLACE ON THE PLANS |
| | FOR REVIEW. |
| | PAGE 2 |
| | |
| | 110.24 AVAILABLE FAULT CURRENT. |
| | (A) FIELD MARKING. SERVICE EQUIPMENT IN OTHER THAN |
| | DWELLING UNITS SHALL BE LEGIBLY MARKED IN THE FIELD |
| | WITH THE |
| | MAXIMUM AVAILABLE FAULT CURRENT. THE FIELD MARKLNG(S) |
| | SHALL |
| | INCLUDE THE DATE THE FAULT-CURRENT CALCULATION WAS |
| | PERFORMED |
| | AND BE OF SUFFICIENT DURABILITY TO WITHSTAND THE |
| | ENVIRONMENT |
| | INVOLVED. |
| | |
| | (B) MODIFICATIONS. WHEN MODIFICATIONS TO THE ELECTRICAL |
| | INSTALLATION OCCUR THAT AFFECT THE MAXIMUM AVAILABLE |
| | FAULT |
| | CURRENT AT THE SERVICE, THE MAXIMUM AVAILABLE FAULT |
| | CURRENT |
| | SHALL BE VERIFIED OR RECALCULATED AS NECESSARY TO |
| | ENSURE THE |
| | SERVICE EQUIPMENT RATINGS ARE SUFTICIENT FOR THE |
| | MAXIMUM |
| | AVAILABLE FAULT CULTENT AT THE LINE TERMINALS OF THE |
| | EQUIPMENT. |
| | THE REQUIRED FIELD MARKING(S) IN LLO.24(A) SHALL BE |
| | ADJUSTED TO |
| | REFLECT THE NEW LEVEL OF MAXIMUM AVAILABLE FAULT |
| | CURRENT |
| | |
| | C405.5 INTERIOR LIGHTING POWER REQUIREMENTS |
| | (PRESCRIPTIVE). |
| | A BUILDING COMPLIES WITH THIS SECTION IF ITS TOTAL |
| | CONNECTED LIGHTING POWER |
| | CALCULATED UNDER SECTION C405.5.1 IS NO GREATER THAN |
| | THE INTERIOR LIGHTING |
| | POWER CALCULATED UNDER SECTION C405.5.2. |
| | |
| | C405.5.1 TOTAL CONNECTED INTERIOR LIGHTING POWER. |
| | THE TOTAL CONNECTED INTERIOR LIGHTING POWER (WATTS) |
| | SHALL BE THE SUM OF THE |
| | WATTS OF ALL INTERIOR LIGHTING EQUIPMENT AS DETERMINED |
| | IN ACCORDANCE WITH |
| | SECTIONS C405.5.1.1 THROUGH C405.5.1.4 |
| | |
| | C405.2.1.1 INTERIOR LIGHTING CONTROLS. |
| | EACH AREA ENCLOSED BY WALLS OR FLOOR-TO-CEILING |
| | PARTITIONS SHALL HAVE AT |
| | LEAST ONE MANUAL CONTROL FOR THE LIGHTING SERVING THAT |
| | AREA. THE REQUIRED |
| | CONTROLS SHALL BE LOCATED WITHIN THE AREA SERVED BY THE |
| | CONTROLS OR BE A |
| | REMOTE SWITCH THAT IDENTIFIES THE LIGHTS SERVED AND |
| | INDICATES THEIR STATUS. |
| | |
| | 408.4 FIELD IDENTIFICATION REQUIRED. |
| | (A) CIRCUIT DIRECTORY OR CIRCUIT IDENTIFICATION. EVERY |
| | CIRCUIT AND CIRCUIT MODIFICATION SHALL BE LEGIBLY |
| | IDENTIFIED AS |
| | TO ITS CLEAR, EVIDENT, AND SPECIFIC PURPOSE OR USE. THE |
| | IDENTIFICATION |
| | SHALL INCLUDE AN APPROVED DEGREE OF DETAIL THAT |
| | ALLOWS EACH CIRCUIT TO BE DISTINGUISHED FROM ALL |
| | OTHERS. |
| | SPARE POSITIONS THAT CONTAIN UNUSED OVERCUN'ENT DEVICES |
| | OR |
| | SWITCHES SHALL BE DESCRIBED ACCORDINGLY. THE |
| | IDENTIFICATION |
| | SHALL BE INCLUDED IN A CIRCUIT DIRECTORY THAT IS |
| | LOCATED ON THE |
| | FACE OR INSIDE OF THE PANEL DOOR IN THE CASE OF A |
| | PANELBOARD |
| | AND AT EACH SWITCH OR CIRCUIT BREAKER IN A SWITCHBOARD |
| | OR |
| | SWITCHGEAR. NO CIRCUIT SHALL BE DESCRIBED IN A MANNER |
| | THAT |
| | DEPENDS ON TRANSIENT CONDITIONS OF OCCUPANCY. |
| | |
| | (B) SOURCE OF SUPPLY. ALL SWITCHBOARDS,SWITEHGEAR, AND |
| | PANELBOARDS SUPPLIED BY A FEEDER(S) IN OTHER THAN ONE- |
| | OR |
| | TWO-FAMILY DWELLINGS SHALL BE MARKED TO INDICATE EACH |
| | DEVICE |
| | OR EQUIPMENT WHERE THE POWER ORIGINATES. |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | . |
| | |
