| Date |
Text |
| 2017-06-28 14:42:40 | 2ND REVIEW |
| | |
| | GEORGE JOHNSON |
| | PLUMBING PLANS EXAMINER LL |
| | CITY OF WEST PALM BEACH |
| | DEVELOPMENT SERVICES |
| | BUILDING DIVISION |
| | 561-805-6711 |
| | [email protected] |
| | |
| | PLUMBING COMMENTS: 2ND REQUEST NOT COMPLIED |
| | |
| | 1. GRAB BARS SHALL BE INSTALLED ABOVE THE FINISH FLOOR |
| | MEASURED TO THE TOP OF THE GRIPPING SURFACE,PER FBC ACC |
| | 609.4 |
| | |
| | 2. TOILET PAPER DISPENSERS SHALL COMPLY WITH 309.4 AND |
| | SHALL BE 7 INCHES MINIMUM AND 9 INCHES MAXIMUM IN FRONT |
| | OF THE WATER CLOSET MEASURED TO THE CENTERLINE OF THE |
| | DISPENSER. PER FBC ACC 604.7 |
| | |
| | 3. THE WATER CLOSET SHALL BE POSITIONED WITH A WALL OR |
| | PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE |
| | OF THE WATER CLOSET SHALL BE 16 INCHES MINIMUM TO 18 |
| | INCHES MAXIMUM FROM THE SIDE WALL OR PARTITION, PER FBC |
| | ACC 604.2 |
| | |
| | 4. PROVIDE DIMENSIONS FOR SHOWERS AND COMPLIANCE WITH |
| | FBC ACC 608 PER FBC ACC 213.3.6 |
| | A) 608.2.2 STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS. |
| | STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS SHALL BE 30 |
| | INCHES (760 MM) WIDE MINIMUM BY 60 INCHES (1525 MM) |
| | DEEP MINIMUM CLEAR INSIDE DIMENSIONS MEASURED AT CENTER |
| | POINTS OF OPPOSING SIDES AND SHALL HAVE A 60 INCHES |
| | (1525 MM) WIDE MINIMUM ENTRY ON THE FACE OF THE SHOWER |
| | COMPARTMENT. |
| | B) 608.2.2.1 CLEARANCE. |
| | A 30 INCH (760 MM) WIDE MINIMUM BY 60 INCH (1525 MM) |
| | LONG MINIMUM CLEARANCE SHALL BE PROVIDED ADJACENT TO |
| | THE OPEN FACE OF THE SHOWER COMPARTMENT. |
| | C) 608.3.2 STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS. |
| | WHERE A SEAT IS PROVIDED IN STANDARD ROLL-IN TYPE |
| | SHOWER COMPARTMENTS, GRAB BARS SHALL BE PROVIDED ON THE |
| | BACK WALL AND THE SIDE WALL OPPOSITE THE SEAT. GRAB |
| | BARS SHALL NOT BE PROVIDED ABOVE THE SEAT. WHERE A SEAT |
| | IS NOT PROVIDED IN STANDARD ROLL-IN TYPE SHOWER |
| | COMPARTMENTS, GRAB BARS SHALL BE PROVIDED ON THREE |
| | WALLS. GRAB BARS SHALL BE INSTALLED 6 INCHES (150 MM) |
| | MAXIMUM FROM ADJACENT WALLS. |
| | D) 608.5.2 STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS. |
| | IN STANDARD ROLL-IN TYPE SHOWER COMPARTMENTS, THE |
| | CONTROLS, FAUCETS, AND SHOWER SPRAY UNIT SHALL BE |
| | LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48 |
| | INCHES (1220 MM) ABOVE THE SHOWER FLOOR. WHERE A SEAT |
| | IS PROVIDED, THE CONTROLS, FAUCETS, AND SHOWER SPRAY |
| | UNIT SHALL BE INSTALLED ON THE BACK WALL ADJACENT TO |
| | THE SEAT WALL AND SHALL BE LOCATED 27 INCHES (685 MM) |
| | MAXIMUM FROM THE SEAT WALL. |
| | |
| | |
| | 5. PROVIDE SANITARY AND WATER RISER DIAGRAM . PER WPB |
| | AMEND TO FBC 107.3.5.1.3(13) |
| | |
| | 5. PROVIDE MANUFACTURE SPECS FOR SUMP PUMP AND OIL |
| | INTERCEPTOR. PER WPB AMEND TO FBC 107.2.1 |
| | |
| | DUE TO THE DEFICIENCIES OF THIS PLAN A COMPLETE AND |
| | THOROUGH REVIEW CANNOT BE DONE AT THIS TIME. UPON |
| | RESUBMITTAL THERE MAYBE ADDITIONAL COMMENTS. |
| | |
| | WHEN RESUBMITTING PLANS, REMOVE AND REPLACE ANY PAGES |
| | AS NECESSARY. A NARRATIVE LISTING THE ORIGINAL REVIEW |
| | COMMENT NUMBER WITH A DESCRIPTION OF THE CHANGES MADE |
| | AND IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE |
| | THE CHANGE CAN BE FOUND WILL HELP EXPEDITE THE REVIEW. |
| | |
