| Date |
Text |
| 2016-11-28 18:17:21 | 1ST REVIEW |
| | |
| | GEORGE JOHNSON |
| | PLUMBING PLANS EXAMINER LL |
| | CITY OF WEST PALM BEACH |
| | DEVELOPMENT SERVICES |
| | BUILDING DIVISION |
| | 561-805-6711 |
| | [email protected] |
| | |
| | PLUMBING COMMENTS: |
| | |
| | 1. GRAB BARS SHALL BE INSTALLED IN A HORIZONTAL |
| | POSITION, 33 INCHES (840 MM) MINIMUM AND 36 INCHES (915 |
| | MM) MAXIMUM ABOVE THE FINISH FLOOR MEASURED TO THE TOP |
| | OF THE GRIPPING SURFACE, PER FBC ACC 609.4 |
| | |
| | 2. TOILET PAPER DISPENSERS SHALL COMPLY WITH 309.4 AND |
| | SHALL BE 7 INCHES (180 MM) MINIMUM AND 9 INCHES (230 |
| | MM) MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO |
| | THE CENTERLINE OF THE DISPENSER. PER FBC ACC 604.7 |
| | |
| | 3. SHOW COMPLIANCE IN TRANSFER TYPE COMPARTMENTS, GRAB |
| | BARS SHALL BE PROVIDED ACROSS THE CONTROL WALL AND BACK |
| | WALL TO A POINT 18 INCHES (455 MM) FROM THE CONTROL |
| | WALL. GRAB BARS SHALL COMPLY WITH 609 AND SHALL BE |
| | PROVIDED IN ACCORDANCE WITH 608.3. WHERE MULTIPLE GRAB |
| | BARS ARE USED, REQUIRED HORIZONTAL GRAB BARS SHALL BE |
| | INSTALLED AT THE SAME HEIGHT ABOVE THE FINISH FLOOR. |
| | PER FBC ACC 608.3.1 |
| | |
| | 4. SHOW COMPLIANCE FBC ACC 608.5.1 TRANSFER TYPE SHOWER |
| | COMPARTMENTS. |
| | IN TRANSFER TYPE SHOWER COMPARTMENTS, THE CONTROLS, |
| | FAUCETS, AND SHOWER SPRAY UNIT SHALL BE INSTALLED ON |
| | THE SIDE WALL OPPOSITE THE SEAT 38 INCHES (965 MM) |
| | MINIMUM AND 48 INCHES (1220 MM) MAXIMUM ABOVE THE |
| | SHOWER FLOOR AND SHALL BE LOCATED ON THE CONTROL WALL |
| | 15 INCHES (380 MM) MAXIMUM FROM THE CENTERLINE OF THE |
| | SEAT TOWARD THE SHOWER OPENING. |
| | |
| | 5. SHOW COMPLIANCE FBC ACC 610.3 IN TRANSFER-TYPE |
| | SHOWERS, THE SEAT SHALL EXTEND FROM THE BACK WALL TO A |
| | POINT WITHIN 3 INCHES (75 MM) OF THE COMPARTMENT ENTRY. |
| | THE TOP OF THE SEAT SHALL BE 17 INCHES (430 MM) MINIMUM |
| | AND 19 INCHES (485 MM) MAXIMUM ABOVE THE BATHROOM |
| | FINISH FLOOR. SEATS SHALL COMPLY WITH 610.3.1 OR |
| | 610.3.2. |
| | 610.3.2 L-SHAPED SEATS. |
| | THE REAR EDGE OF AN L-SHAPED SEAT SHALL BE 2 1/2 INCHES |
| | (64 MM) MAXIMUM AND THE FRONT EDGE 15 INCHES (380 MM) |
| | MINIMUM AND 16 INCHES (405 MM) MAXIMUM FROM THE SEAT |
| | WALL. THE REAR EDGE OF THE ?L? PORTION OF THE SEAT |
| | SHALL BE 11/2 INCHES (38 MM) MAXIMUM FROM THE WALL AND |
| | THE FRONT EDGE SHALL BE 14 INCHES (355 MM) MINIMUM AND |
| | 15 INCHES (380 MM) MAXIMUM FROM THE WALL. THE END OF |
| | THE ?L? SHALL BE 22 INCHES (560 MM) MINIMUM AND 23 |
| | INCHES MAXIMUM (585 MM) FROM THE MAIN SEAT WALL. |
| | |
