| Date |
Text |
| 2016-11-01 12:00:00 | 1ST REVIEW FBC-2014 MECHANICAL, EXISTING BUILDING CODES |
| | PERMIT #16100664 |
| | 11/1/16 |
| | |
| | 1) DESIGN CRITERIA: PROVIDE ON THE PLAN A LIST OF |
| | CURRENT CODE REFERENCES AND STANDARDS USED IN THE |
| | DESIGN OF THE PROJECT. |
| | |
| | 2) THE MECHANICAL PLANS MUST BE DESIGNED BY A FLORIDA |
| | LICENSED ENGINEER PER FLORIDA STATUTE 471.003. THE SEAL |
| | ON THE PLANS INDICATES THE DESIGNER HAS A "CERTIFICATE" |
| | BUT IS NOT LICENSED. |
| | |
| | 3) REFER TO SECTION C408.2 FBC-14 ENERGY CONSERVATION- |
| | AC SYSTEM COMMISSIONING IS REQUIRED. |
| | C408.2 MECHANICAL SYSTEMS COMMISSIONING AND COMPLETION |
| | REQUIREMENTS. |
| | PRIOR TO PASSING THE FINAL MECHANICAL INSPECTION, THE |
| | REGISTERED DESIGN PROFESSIONAL SHALL PROVIDE EVIDENCE |
| | OF MECHANICAL SYSTEMS COMMISSIONING AND COMPLETION IN |
| | ACCORDANCE THE PROVISIONS OF THIS SECTION. |
| | CONSTRUCTION DOCUMENT NOTES SHALL CLEARLY INDICATE |
| | PROVISIONS FOR COMMISSIONING AND COMPLETION |
| | REQUIREMENTS IN ACCORDANCE WITH THIS SECTION AND ARE |
| | PERMITTED TO REFER TO SPECIFICATIONS FOR FURTHER |
| | REQUIREMENTS. COPIES OF ALL DOCUMENTATION SHALL BE |
| | GIVEN TO THE OWNER AND MADE AVAILABLE TO THE CODE |
| | OFFICIAL UPON REQUEST IN ACCORDANCE WITH SECTIONS |
| | C408.2.4 AND C408.2.5. |
| | |
| | 2A) C408.2.1 COMMISSIONING PLAN. |
| | A COMMISSIONING PLAN SHALL BE DEVELOPED BY A REGISTERED |
| | DESIGN PROFESSIONAL OR APPROVED AGENCY AND SHALL |
| | INCLUDE THE FOLLOWING ITEMS: |
| | |
| | 1. A NARRATIVE DESCRIPTION OF THE ACTIVITIES THAT WILL |
| | BE ACCOMPLISHED DURING EACH PHASE OF COMMISSIONING, |
| | INCLUDING THE PERSONNEL INTENDED TO ACCOMPLISH EACH OF |
| | THE ACTIVITIES. |
| | 2. A LISTING OF THE SPECIFIC EQUIPMENT, APPLIANCES OR |
| | SYSTEMS TO BE TESTED AND A DESCRIPTION OF THE TESTS TO |
| | BE PERFORMED. |
| | 3. FUNCTIONS TO BE TESTED, INCLUDING, BUT NOT LIMITED |
| | TO CALIBRATIONS AND ECONOMIZER CONTROLS. |
| | 4. CONDITIONS UNDER WHICH THE TEST WILL BE PERFORMED. |
| | AT A MINIMUM, TESTING SHALL AFFIRM WINTER AND SUMMER |
| | DESIGN CONDITIONS AND FULL OUTSIDE AIR CONDITIONS. |
| | 5. MEASURABLE CRITERIA FOR PERFORMANCE. |
| | |
| | 3) SHEET M002: PROVIDE IN THE SCHEDULE THE EFFICIENCY |
| | RATING OF THE NEW EVAPCO COOLING TOWER- SEE TABLE |
| | C403.2.3(8) FBC-14 ENERGY CONSERVATION. |
| | |
| | 4) PROVIDE WATER PIPING AND PIPE INSULATION |
| | SPECIFICATIONS. INDICATE THE SPACING OF THE PIPE |
| | SUPPORTS ON THE ROOF. |
| | |
| | 5) S301: INDICATE THE CLEARANCE DISTANCE HEIGHT FROM |
| | THE FINISHED ROOF SURFACE TO THE BOTTOM OF THE COOLING |
| | TOWER SUPPORT BASE- REFER TO SECTION 102.8 AND TABLE |
| | 1522.3 FBC-14 BUILDING. |
| | |
| | 6) REFER TO SECTION 908.2 AND INDICATE HOW ACCESS TO |
| | THE COOLING TOWER WILL BE PROVIDED- THE PLANS DO NOT |
| | INDICATE ANY STAIRS OR PLATFORMS. |
| | |
| | 7) REFER TO SECTION 702.4 FBC-14 EXISTING BUILDING AND |
| | VERIFY THAT ALL MECHANICAL ROOFTOP EQUIPMENT IS NOT |
| | LOCATED WITHIN 10' OF ANY ROOF EDGE THAT DOES NOT HAVE |
| | A GUARD OR PARAPET AT A MINIMUM HEIGHT OF 42"- SEE |
| | SECTION 304.11 FBC-14 MECHANICAL. |
| | |
| | 8) M101: SHOW THE CLEARANCE DISTANCE MEASUREMENTS FROM |
| | THE COOLING TOWER DISCHARGE TO THE RTU AIR INLETS- SEE |
| | SECTION 908.3. |
| | |
| | 9) M201: THE CONDENSATE PIPING SPECIFIED IN DETAIL 1 |
| | CANNOT DRAIN ONTO THE ROOF SURFACE AS SPECIFIED. THE |
| | PIPING SHALL TERMINATE AT AN APPROVED PLACE OF DISPOSAL |
| | SUCH AS A ROOF DRAIN, A DRY WELL, OR PERMEABLE GROUND |
| | WHERE IT WILL NOT BE A NUISANCE- SECTION 307.2.1. |
| | |
| | CHRISTOPHER L. COLE |
| | MECHANICAL PLANS EXAMINER |
| | 561-805-6719 |
| | [email protected] |
| | |
