| Date |
Text |
| 2016-01-24 05:13:40 | 1)SHT.A100 SHOWS CONTINUOUS GRAB BARS IN THE ACCESSIBLE |
| | TOILET ROOMS. GRAB BARS SHALL COMPLY WITH 2014 |
| | FBC-ACCESS. SECS.604.5.1, 604.5.2, & 609. NOTE 11 ON |
| | A11 INDDICATES 24" & 36" GRAB BARS.CLARIFY. |
| | 604.5.1 SIDE WALL. |
| | THE SIDE WALL GRAB BAR SHALL BE 42 INCHES (1065 MM) |
| | LONG MINIMUM, LOCATED 12 INCHES (305 MM) MAXIMUM FROM |
| | THE REAR WALL AND EXTENDING 54 INCHES (1370 MM) MINIMUM |
| | FROM THE REAR WALL. |
| | 604.5.2 REAR WALL. |
| | THE REAR WALL GRAB BAR SHALL BE 36 INCHES (915 MM) LONG |
| | MINIMUM AND EXTEND FROM THE CENTERLINE OF THE WATER |
| | CLOSET 12 INCHES (305 MM) MINIMUM ON ONE SIDE AND 24 |
| | INCHES (610 MM) MINIMUM ON THE OTHER SIDE. |
| | 609.1 GENERAL. |
| | GRAB BARS IN TOILET FACILITIES AND BATHING FACILITIES |
| | SHALL COMPLY WITH 609. |
| | 609.2 CROSS SECTION. |
| | GRAB BARS SHALL HAVE A CROSS SECTION COMPLYING WITH |
| | 609.2.1 OR 609.2.2. |
| | 609.2.1 CIRCULAR CROSS SECTION. |
| | GRAB BARS WITH CIRCULAR CROSS SECTIONS SHALL HAVE AN |
| | OUTSIDE DIAMETER OF 11/4 INCHES (32 MM) MINIMUM AND 2 |
| | INCHES (51 MM) MAXIMUM. |
| | 609.2.2 NON-CIRCULAR CROSS SECTION. |
| | GRAB BARS WITH NON-CIRCULAR CROSS SECTIONS SHALL HAVE A |
| | CROSS-SECTION DIMENSION OF 2 INCHES (51 MM) MAXIMUM AND |
| | A PERIMETER DIMENSION OF 4 INCHES (100 MM) MINIMUM AND |
| | 4.8 INCHES (120 MM) MAXIMUM. |
| | 609.3 SPACING. |
| | THE SPACE BETWEEN THE WALL AND THE GRAB BAR SHALL BE 1 |
| | 1/2 INCHES (38 MM). THE SPACE BETWEEN THE GRAB BAR AND |
| | PROJECTING OBJECTS BELOW AND AT THE ENDS SHALL BE 1 1/2 |
| | INCHES (38 MM) MINIMUM. THE SPACE BETWEEN THE GRAB BAR |
| | AND PROJECTING OBJECTS ABOVE SHALL BE 12 INCHES (305 |
| | MM) MINIMUM. |
| | EXCEPTION: THE SPACE BETWEEN THE GRAB BARS AND SHOWER |
| | CONTROLS, SHOWER FITTINGS, AND OTHER GRAB BARS ABOVE |
| | SHALL BE PERMITTED TO BE 1 1/2 INCHES (38 MM) MINIMUM. |
| | 609.4 POSITION OF GRAB BARS. |
| | GRAB BARS SHALL BE INSTALLED IN A HORIZONTAL POSITION, |
| | 33 INCHES (840 MM) MINIMUM AND 36 INCHES (915 MM) |
| | MAXIMUM ABOVE THE FINISH FLOOR MEASURED TO THE TOP OF |
| | THE GRIPPING SURFACE. |
| | 2) CLEARLY SHOW ON THE WATER RISER THAT BOTH LAVATORIES |
| | ARE SUPPLIED WITH HOT OR TEMPERED WATER, LIMITED TO 110 |
| | DEGREES IN ACCORDANCE WITH THE 2014 FBC-PLUMBING |
| | SEC.607.1, 607.1.1, 607.1.2. |
| | 3) SHOW THE NEW LAVATORY IN THE NEW ACCESSIBLE TOILET |
| | ROOM ON THE SANITARY RISER. |
| | 4) THE SANITARY SHOWS A FLAT DRY VENT WHICH IS NOT |
| | PERMITTED PER THE PLUMBING CODE. THE VENT SHALL CONNECT |
| | TO THE HORIZONTAL DRAIN ABOVE THE CENTERLINE OF THE |
| | HORIZONTAL DRAIN PIPE. 2014 FBCP SEC.905.3. |
| | 5) SHT. A100 - THE TYPICAL HANDICAP RESTROOM DETAIL |
| | SHOWS THE MINIMUM INSIDE DIMENSION AS 7'-6" AND THE |
| | PLAN VIEW SHOWS THE RESTROOM AS 7'-8" FROM THE INSIDE |
| | FACE OF THE WALL TO THE OUTSIDE FACE OF THE WALL AS |
| | 7'-8". CLARIFY. SHOW THE THE INSIDE CLEAR DIMENSIONS OF |
| | THE ACCESSIBLE TOILET ROOMS.THE MINIMUM WIDTH WHEN THE |
| | THE PLUMBING FIXTURES ARE ON THE SAME WALL IS 85 |
| | INCHES.86 INCHES ALLOWS FOR TOLERANCE. |
| | 6) THE MANUF. SPECS/INSTALLATION MANUAL FOR THE |
| | TANKLESS WATER HEATER SHALL BE ONSITE FOR THE |
| | INSPECTOR. |
| | |
| | PLUMBING PLAN REVIEW |
| | TIM LARGE |
| | CHIEF PLUMBING INSPECTOR |
| | 561-805-6692 |
| | [email protected] |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
