| Date |
Text |
| 2009-01-16 17:04:57 | RESIDENTIAL (R3) ALTERATION BUILDING REVIEW CHECKLIST. |
| | REVIEW UNDER 2004 FLORIDA RESIDENTIAL CODE WITH 2007 |
| | REVISIONS. |
| | |
| | 1- NEED RECORDED NOTICE OF COMMENCEMENT. SEC. 713.13 |
| | FLORIDA STATUTE. |
| | **NOTE: THIS MAY BE RECORDED AT TIME OF PERMIT PICK UP. |
| | |
| | 2- AFTER PLANS ARE REVISED, BRING THEM TO PALM BEACH |
| | COUNTY TO CHECK IF IMPACT FEES ARE DUE. BRING BACK |
| | STAMPED PLANS AND COPY OF PAID RECEIPT IF FEES ARE DUE. |
| | |
| | 3- PROVIDE 2 COPIES OF PRODUCT APPROVALS AS REQUIRED BY |
| | DCA RULE 9B-72 FOR: |
| | A) STORM SHUTTERS: |
| | *PROVIDE COMPLETE PRODUCT APPROVAL REPORT AND MAKE SURE |
| | DRAWINGS MATCH FLORIDA PRODUCT APPROVAL REPORT. |
| | DRAWINGS SUBMITTED (05-270) DON'T MATCH FLORIDA PRODUCT |
| | APPROVAL FL6968. |
| | |
| | **PROVIDE COMPLETE INSTALLATION SCHEDULE. SEE ATTACHED |
| | SAMPLE. AND CLEARLY MARK ON SHUTTERS DRAWINGS SPECIFIC |
| | MOUNTING CONDITIONS WALL SECTION (EG: WALL MOUNT, BUILD |
| | OUT, ETC) AND SPECIFIC ANCHOR TYPE AND SPACING TO BE |
| | USED TO VERIFY COMPLIANCE WITH THE PRODUCT AND |
| | CALCULATED DESIGN PRESSURES. |
| | NOTE: SEE REVISED DESIGN PRESSURES PRIOR TO COMPLETING |
| | INSTALLATION SCHEDULE. SEE ITEM 10B BELOW. |
| | |
| | B) "INSWING" ENTRY DOOR AS SHOWN ON FLOOR PLANS. |
| | CLARIFY IF PRODUCT APPROVAL FL5114 SUBMITTED IS THE ONE |
| | GOING TO BE INSTALLED ON THE FRONT DOOR. |
| | NOTE: THIS DOOR REQUIRES SHUTTERS. COORDINATE WITH ITEM |
| | #3A ABOVE. |
| | |
| | C) PAIR OF FRENCH DOORS AS SHOWN ON PLANS. NONE |
| | SUBMITTED AT THIS TIME. |
| | |
| | D) FLAT ROOF ASSEMBLY. PRODUCT APPROVAL SUBMITTED (NOA |
| | 06-0105.04) IF FOR CLAY ROOFING TILE. THERE IS NOT CLAY |
| | TILE SHOWN ON DRAWINGS. ALSO, THE OTHER PRODUCT |
| | APPROVAL SUBMITTED (NOA 06-0113.03) IS FOR PITCHED ROOF |
| | UNDERLAYMENT ONLY. |
| | NOTE: ON FLAT ROOF PRODUCT APPROVAL SPECIFY AND PROVIDE |
| | THE FOLLOWING: |
| | *CLEARLY SPECIFY WHICH APPROVED ASSEMBLY IS GOING TO BE |
| | INSTALLED. SEE LIST OF APPROVED ASSEMBLIES ON PRODUCT |
| | APPROVAL. |
| | |
| | **CLEARLY SPECIFY WHICH FASTENING OPTION IS GOING TO BE |
| | USED TO FASTEN THE FLAT ROOF BASE SHEET. |
| | |
| | ***PROVIDE RAS 117 CALCULATIONS AS REQUIRED BY GENERAL |
| | LIMITATION #7 FOR NAIL ENHANCING AT PERIMETER AND |
| | CORNER AREAS. SEE GENERAL LIMITATION #7 ON LAST PAGE OF |
| | NOA. IF CALCULATIONS NEED TO BE SIGNED AND SEALED, THEN |
| | PROVIDE SUCH INFORMATION SIGNED AND SEALED. |
| | NOTE: GENERAL LIMITATION #9 CAN'T BE USED IN THIS JOB. |
| | |
| | E) SINGLE HUNG WINDOWS. INFORMATION SUBMITTED IS |
| | MISSING THE PRODUCT APPROVAL COVER PAGE WITH THE |
| | FLORIDA PRODUCT APPROVAL NUMBER. |
| | ALSO, DRAWINGS ARE NOT LEGIBLE. NEED TO PROVIDE LEGIBLE |
| | DRAWINGS. |
| | |
| | F) PRECAST LINTELS AS SPECIFIED ON PLANS. |
| | |
| | G) ALL SIMPSON STRUCTURAL CONNECTORS SPECIFIED ON PLANS |
| | AND DETAILS. |
| | NOTE: PROVIDE ONLY THE FLORIDA PRODUCT APPROVAL COVER |
| | PAGE AND SHEET WHERE THE CONNECTOR IS SHOWN. THIS |
| | APPLIES TO CONNECTORS ONLY. OTHER PRODUCT APPROVALS |
| | NEED TO PROVIDE COMPLETE REPORT. VISIT |
| | WWW.FLORIDABUILDING.ORG TO DOWNLOAD ALL FLORIDA PRODUCT |
| | APPROVALS. |
| | |
| | 4- ENGINEER OF RECORD TO REVIEW AND APPROVE IN WRITING |
| | (NOT SIGNING AND SEALING) ALL PRODUCT APPROVALS AS |
| | REQUIRED BY SEC. 106.3.3 CITY AMENDMENTS TO FBC 2004. |
| | |
| | 5- BRING ALL REVISED PLANS FOR HISTORIC REVIEW APPROVAL |
| | STAMP PRIOR TO SUBMITTAL TO THIS OFFICE. |
| | |
| | 6- SHEET 2.1: CLARIFY WHY THERE IS NOT FILLED CELLS AND |
| | VERTICAL REINFORCEMENT SHOWN ON SOUTH WALL. |
| | ALSO, SPECIFY VERTICAL REINFORCEMENT SPACING ON THE |
| | OTHER WALLS AS REQUIRED BY SEC. R609.3.3 OF 2004 |
| | FLORIDA RESIDENTIAL CODE. |
| | |
| | 7 SHEET 3.1: REVISE DESIGN PARAMETERS SPECIFICATIONS. |
| | REFERENCE ASCE 7-02 WHICH IS THE CURRENT CODE, NOT ASCE |
| | 7-05. |
| | |
| | 8- SHEET 4.1: |
| | A) CLARIFY WHAT'S CONNECTOR #22. SHOWN ON ROOF FRAMING |
| | PLAN. WHAT'S LUS10 AS SHOWN ON CONNECTOR SCHEDULE?. |
| | |
| | B) SPECIFY SIZE OF NEW 2 PLY GIRDER SHOWN ON ROOF |
| | FRAMING PLAN WHERE EXISTING ROOF MEETS NEW ROOF. |
| | ALSO, SPECIFY CONNECTION AT BOTH ENDS TO VERIFY |
| | COMPLIANCE WITH CALCULATED UPLIFT PRESSURES OF SEC. |
| | R301 OF 2004 FLORIDA RESIDENTIAL CODE. |
| | |
| | C) CLARIFY WHY IS THERE A NOTE ON ROOF FRAMING PLAN |
| | SAYING AREA OF REMODEL AND 2ND FLOOR. THIS IS ONLY A |
| | ONE STORY CONSTRUCTION. |
| | |
| | D) COMPONENT AND CLADDING PRESSURE ZONES IS MISSING THE |
| | NAILING AT INTERMEDIATE SUPPORTS FOR ROOF ZONE #3. SEE |
| | SEC. R803.2.3.1 OF 2004 FLORIDA RESIDENTIAL CODE FOR |
| | MIN. TYPE AND NAILING REQUIRED FOR ROOF ZONE #3. |
| | |
| | E) REVISE/CLARIFY GENERAL ROOF NOTE #7. COORDINATE WITH |
| | ITEM 9D ABOVE. |
| | |
| | F) NEED TO PROVIDE ROOF CROSS VENTILATION AS REQUIRED |
| | BY SEC. R806 OF 2004 FLORIDA RESIDENTIAL CODE. THERE |
| | ARE 2 VENTILATION OPENINGS SPECIFIED. THEY DON'T |
| | PROVIDE ROOF CROSS VENTILATION BECAUSE ROOF FRAMING |
| | PLANS SHOWS 2X12 SOLID ROOF RAFTERS. |
| | |
| | G) CLARIFY SIZE OF ROOF SCUPPERS. ROOF DRAIN SECTION |
| | CALLS FOR 4"X12" SCUPPERS, WHILE NOTE BY ROOF FRAMING |
| | PLAN CALLS FOR 6"X14" SCUPPERS. |
| | |
| | 9- SHEET 5.1: |
| | A) EXTERIOR DOOR HEAD JAMB DETAIL. REVISE SIZE OF |
| | STRUCTURAL BUCK. 2X4 STRUCTURAL BUCK IS NOT ADEQUATE TO |
| | PROVIDE DOOR FRAME FULL SUPPORT AS REQUIRED BY SEC. |
| | R613.6 OF 2004 FLORIDA RESIDENTIAL CODE. ALSO, SEE |
| | PRODUCT APPROVAL FOR FRAME SIZE. |
| | |
| | B) DESIGN PRESSURES SHOWN ON COMPONENTS AND CLADDING |
| | DON'T CORRESPOND TO EXPOSURE "C". REVISE DESIGN |
| | PRESSURES AS REQUIRED. |
| | |
| | C) CLARIFY WHY ALL EXTERIOR ELEVATIONS MAKE REFERENCE |
| | TO NEW 2ND STORY. THERE IS NO 2 STORY CONSTRUCTION ON |
| | THIS PROJECT. |
| | |
| | 10- SHEET 6.1, TYPICALL WALL SECTION: |
| | A) CLARIFY SPECS GIVEN FOR THE FLAT ROOF ASSEMBLY. SEE |
| | PRODUCT APPROVAL FOR CORRECT INFORMATION. INFORMATION |
| | SUBMITTED IS FOR PITCHED ROOFS, NOT FOR LOW SLOPE |
| | ROOFS. REVISE AS REQUIRED. |
| | |
| | B) REVISE INFORMATION REGARDING ROOF TRUSSES AT |
| | 24"O.C.. SEE ROOF FRAMING PLAN FOR FRAMING MEMBERS |
| | SPECIFIED. |
| | |
| | C) SPACING FOR 2X10 LEDGER ANCHORS DON'T MATCH |
| | INFORMATION GIVEN ON ROOF FRAMING PLAN. REVISE AS |
| | REQUIRED. |
| | |
| | D) REVISE NOTE REGARDING TWO STORY CONSTRUCTION. |
| | |
| | 11- REVISE ENERGY CALCULATIONS: |
| | A) PROVIDE PROJECT ADDRESS AND COMPLETE ALL THE |
| | INFORMATION ON TOP OF FORM. |
| | |
| | B) ARE THE ENERGY CALCULATIONS FOR THE ENTIRE HOUSE OR |
| | FOR AREA OF WORK ONLY. IS NEW INSULATION PROVIDED FOR |
| | THE ENTIRE HOUSE IN WALLS AND CEILINGS. ALSO, SEE TYPE |
| | OF WALLS ON EXISTING STRUCTURE. THIS INFORMATION IS NOT |
| | SHOWN ON PLANS. |
| | |
| | C) PROVIDE COMPLETE MANUFACTURER'S SPECIFICATIONS |
| | SHOWING THE U-FACTOR AND SHGC FACTOR SHOWN ON ITEMS 7A |
| | AND 7B WHEN THE DEFAULT FACTOR IS NOT USED. (IN |
| | ADDITION WINDOWS AND DOORS NEED TO SHOW SUCH RATING FOR |
| | INSPECTION AFTER INSTALLATION). |
| | |
| | D) OWNER/AGENT TO SIGN AND DATE BOTTOM OF FORM. |
| | |
| | 12- SOIL TEST REPORT SUBMITTED TO BE ADDRESSED TO |
| | CORRECT BUILDING DEPARTMENT AND ADDRESS. THIS IS THE |
| | CITY OF WEST PALM BEACH, NOT PALM BEACH COUNTY. AND |
| | CORRECT ADDRESS IS 200 2ND STREET, WPB, FL 33401. |
| | |
| | JULIO GOMEZ |
| | BUILDING PLANS EXAMINER |
| | (561)805-6712 |
