| Date |
Text |
| 2007-09-06 16:35:30 | 2004 FBC W/2007 SUPPLEMENT |
| | LEVEL 3 ALTERATION AND ADDITION |
| | |
| | DENIED BY BUILDING |
| | |
| | 1) A RECORDED COPY OF THE NOTICE OF COMMENCEMENT |
| | MUST BE SUBMITTED BEFORE A |
| | PERMIT CAN BE ISSUED. |
| | |
| | 2) IMPACT FEES MUST BE PAID TO PALM |
| | BEACH COUNTY, PLANS STAMPED BY THEM AND |
| | COPY OF RECEIPT SUBMITTED TO CITY OF |
| | WEST PALM BEACH BUILDING DEPARTMENT, |
| | BEFORE A BUILDING PERMIT CAN BE ISSUED. |
| | |
| | 3) CORRECT THE JURISDICTION LISTED ON THE COVERSHEET TO |
| | THE CITY OF WEST PLAM BEACH. |
| | |
| | 4) SPECIFY THE OCCUPANCY TYPE OF THE EXISTING |
| | STRUCTURE. SEE FBC 302. |
| | |
| | 5) IF THE OCCUPANCY OF THE STRUCTURE IS BEING CHANGED, |
| | THE FBC EXISTING BUILDING CODE 807.2 REQUIRES THE |
| | STRUCTURE TO BE ANALYZED AND MADE TO COMPLY WITH THE |
| | APPLICABLE WIND LOAD PROVISIONS. |
| | |
| | 6) SPECIFY THE LOCATIONS AND SIZE OF THE VERTICAL |
| | REINFORCEMENT OF THE MASONRY WALLS. |
| | |
| | 7) SPECIFY THE SIZE AND REINFORCING OF THE EXISTING |
| | FOOTING. |
| | |
| | 8) SPECIFY THE SIZE AND REINFORCING OF THE EXISTING TIE |
| | BEAM. |
| | |
| | 10) SPECIFY THE WIDTH OF THE NEW FOOTING FOR THE |
| | INTERIOR LOAD BEARING WALL. |
| | |
| | 11) CORRECT THE REINFORCING NOTE ON SHEET A1 FOR THE |
| | NEW CONCRETE FOOTING THAT SPECIFIES (4) #5 BUCK. |
| | |
| | 12) THE FLOOR TRUSSES SUPPORTING THE WOOD FRAME |
| | EXTERIOR WALL DO NOT HAVE AN ID TAG ON S1. |
| | |
| | 13) SHOW COMPLIANCE WITH R309.2 SEPARATION REQUIRED. |
| | THE GARAGE SHALL BE SEPARATED FROM THE RESIDENCE AND |
| | ITS ATTIC AREA BY NOT LESS THAN 1/2 -INCH (12.7 MM) |
| | GYPSUM BOARD APPLIED TO THE GARAGE SIDE. GARAGES |
| | BENEATH HABITABLE ROOMS SHALL BE SEPARATED FROM ALL |
| | HABITABLE ROOMS ABOVE BY NOT LESS THAN 5 / 8 -INCH |
| | (15.9 MM) TYPE X GYPSUM BOARD OR EQUIVALENT. WHERE THE |
| | SEPARATION IS A FLOOR-CEILING ASSEMBLY, THE STRUCTURE |
| | SUPPORTING THE SEPARATION SHALL ALSO BE PROTECTED BY |
| | NOT LESS THAN 1/2-INCH (12.7 MM) GYPSUM BOARD OR |
| | EQUIVALENT. |
| | |
| | 14) R311.5.3.2 REQUIRES STAIR TREADS AND RISERS TO BE |
| | PROPORTIONED SUCH THAT THE SUM OF TWO RISERS AND A |
| | TREAD, EXCLUSIVE OF THE NOSING, IS NOT LESS THAN 24 |
| | INCHES NOR MORE THAN 25 INCHES. |
| | |
| | 15) SHOW COMPLIANCE WITH R311.2.2 UNDER STAIR |
| | PROTECTION. |
| | ENCLOSED ACCESSIBLE SPACE UNDER STAIRS SHALL HAVE |
| | WALLS, UNDER STAIR SURFACE AND ANY SOFFITS PROTECTED ON |
| | THE ENCLOSED SIDE WITH 1/2 -INCH (12.7 MM) GYPSUM |
| | BOARD. |
| | |
| | 16) R312.2 REQUIRES THE INTERMEDIATE RAILS ON GUARDS TO |
| | PREVENT THE PASSAGE OF A 4" SPHERE. THEREFORE, THE |
| | OPENINGS MUST BE LESS THAN 4 INCHES. PLEASE REVISE NOTE |
| | ON S1. |
| | |
| | 17) THE GABLE END DETAIL ON S1 SHOWS A VENTED VINYL |
| | SOFFIT AND THE WALL SECTION ON E1 SHOWS A STUCCO |
| | SOFFIT. PLEASE CORRECT. |
| | |
| | 18) THE EXTERIOR WALL COVERING IS SPECIFIED AS CEDAR |
| | SHAKES ON A1 AND THE WALL SECTION ON E1 SHOWS STUCCO. |
| | PLEASE CORRECT. |
| | |
| | 19) ASTM C 926 REQUIRES STUCCO APPLIED VERTICALLY TO |
| | WIRE LATH OF A SOLID BASE TO BE 7/8" THICK. PLEASE |
| | REVISE THE NOTES ON THEWALL SECTION ON E1. |
| | |
| | 20) ASTM C 1063 REQUIRES THE NAILS OR STAPLES USED TO |
| | ATTACH HIGH RIB METAL LATH TO PROVIDE AT LEAST 1-3/4" |
| | PENETRATION INTO HORIZONTAL WOOD FRAMING MEMBERS AND |
| | 3/4" PENETRATION INTO VERTICAL WOOD FRAMING MEMBERS. |
| | |
| | 21)THE MTS 12 WOOD TO WOOD CONNECTORS DO NOT PROVIDE |
| | ANY RESISTANCE TO LATERAL LOADS. SPECIFY HOW THE |
| | LATERAL LOADS AT THE TOP OF THE SECOND FLOOR WALLS WILL |
| | BE RESISTED. |
| | |
| | 22) THE CS18 STRAPS SPECIFIED ON E1 ARE NOT DESIGNED |
| | FOR USE WITH CONCRETE/MASONRY. PLEASE SPECIFY A STRAP |
| | THAT IS DESIGNED AND TESTED FOR THIS APPLICATION SUCH |
| | AS MSTAM OR MSTCM. |
| | |
| | 23) SPECIFY THE COMPONENT AND CLADDING PRESSURES FOR |
| | THE OVERHEAD DOOR AND THE SIDE SWING DOOR ON SHEET A1. |
| | |
| | 24) SPECIFY THE INSULATION FOR THE 2 X 6 WOOD FRAME |
| | WALLS ON THE SECOND FLOOR AND THE FLOOR INSULATION |
| | ABOVE THE GARAGE ON THE ENERGY CALCULATION FORM. |
| | |
| | 25)SUBMIT 2 COPIES OF PRODUCT APPROVALS FOR THE 16' |
| | WIDE OVERHEAD GARAGE DOOR AND THE FIXED GLASS WINDOWS. |
| | |
| | 26) THE MODEL NUMBER SPECIFIED ON THE PLANS FOR THE |
| | SINGLE HUNG WINDOWS DOES NOT CORRESPOND TO THE WINDOW |
| | PRODUCT APPROVALS THAT WERE SUBMITTED. PLEASE CORRECT. |
| | |
| | 27) THE SH 24 WINDOW SPECIFIED FOR THE SECOND FLOOR |
| | BEDROOM TYPICALLY WILL NOT MEET THE CLEAR OPENING |
| | HEIGHT REQUIREMENT. SUBMIT THE CLEAR OPENING DIMENSIONS |
| | FOR THIS WINDOW FROM THE MANUFACTURER SHOWING |
| | COMPLIANCE WITH R310 OR SPECIFY ANOTHER WINDOW. |
| | |
| | 27) THE NOAS THAT WERE SUBMITTED FOR THE FRENCH DOORS |
| | AND THE SINGLE HUNG WINDOWS WERE INCOMPLETE. SUBMIT THE |
| | COMPLETE NOAS INCLUDING THE APPROVED DRAWINGS. |
| | |
| | 28) THE PLANS SHOW A SIX PANEL EXTERIOR DOOR AND THE |
| | PRODUCT APPROVALS SUBMITTED ARE FOR A GLAZED FRENCH |
| | DOOR. PLEASE CLARIFY. |
| | |
| | 29) ON THE SECOND STORY FLOOR PLAN ON A1 THE WINDOWS |
| | ARE DESIGNATED BY THE LETTER 'C'. THE PRODUCT APPROVALS |
| | THAT WERE SUBMITTED ARE FOR SINGLE HUNG WINDOWS. PLEASE |
| | CHANGE THE 'C' TO 'SH' ON THE PLAN TO DENOTE SINGLE |
| | HUNG WINDOWS AND AVOID CONFUSION. |
| | |
| | - ROBERT MCDOUGAL |
| | BLDG. PLAN REVIEW |
| | (561)805-6714 |
| | [email protected] |
| | |
| | |
| | |
| | |
| | |
| | |
