| Date |
Text |
| 2007-01-09 16:57:14 | DENIED |
| | REFERENCE: FBC-2004 PLUMBING AND FBC-2004 CHAPTER 1 |
| | |
| | THE FOLLOWING CORRECTIONS ARE REQUIRED FOR PLUMBING |
| | PLAN REVIEW IN ORDER TO MEET CODE COMPLIANCE. PLEASE |
| | SUBMIT PLUMBING PLANS FOR REVIEW INDICATING THE SCOPE |
| | OF WORK TO BE DONE PER THE FOLLOWING: |
| | |
| | 1. PER FBC-2004 CHAPTER 1 SECTION 106.3.5.4 RESIDENTIAL |
| | (ONE AND TWO |
| | FAMILY) SUBMIT A PLUMBING SANITARY |
| | ISOMETRIC RISER DIAGRAM INDICATING ALL |
| | WASTE, VENTS, TRAPS WITH SIZES, AND |
| | CLEANOUT LOCATIONS FOR THE NEW PROPOSED PLUMBING |
| | INDICATED ON SHEET A-1. |
| | NOTE: IMPORTANT INFORMATION FOR NEW LAUNDRY PER |
| | FBC-2004 PLUMBING. |
| | (A) SECTION 406.3 WASTE CONNECTIONS.THE TRAP AND |
| | FIXTURE DRAIN FOR AN AUTOMATIC CLOTHES |
| | WASHER SHALL BE A MINIMUM OF 2 INCHES |
| | (51MM) IN DIAMETER. THE AUTOMATIC |
| | CLOTHES WASHER FIXTURE DRAIN SHALL |
| | CONNECT TO A BRANCH DRAIN OR DRAINAGE |
| | STACK A MINIMUM OF 3 INCHES (76MM) IN |
| | DIAMETER. |
| | (B) 802.4 STANDPIPES.STANDPIPES SHALL BE INDIVIDUALLY |
| | TRAPPED. STANDPIPES SHALL |
| | EXTEND A MINIMUM OF 18 INCHES (457MM) |
| | AND A MAXIMUM OF 42 INCHES (1066MM) |
| | ABOVE THE TRAP WEIR. ACCESS SHALL BE |
| | PROVIDED TO ALL STANDPIPES AND DRAINS |
| | FOR RODDING.PLEASE INDICATE STANDPIPES ON RESUBMITTAL. |
| | NOTE: PLEASE INDICATE STANDPIPES ON DRAWING. |
| | (C) 708.9 ACCESS. ACCESS SHALL BE |
| | PROVIDED TO ALL CLEANOUTS. PLEASE INDICATE THE CLEANOUT |
| | FOR WASHING MACHINNE AT FOUR FEET ABOVE FINNISH FLOOR |
| | (4' A.F.F.) |
| | |
| | 2. SHEET A-4 INDICATES NEW DOWNSPOUTS AND SCUPPERS: |
| | PLEASE PROVIDE THE FOLLOWING INFORMATION. |
| | A} DETAIL OF ROOF INDICATING SQUARE FOOTAGE OF ROOF AND |
| | VERTICAL WALLS DRAINING TO DOWNSPOUTS AND SCUPPERS TO |
| | VERIFY COMPLIANCE WITH FBC-2004 PLUMBING SECTIONS |
| | 1106.2 VERTICAL CONDUCTORS AND LEADERS, 1106.4 VERTICAL |
| | WALLS, 1106.7 SCUPPERS, AND 1107.2 SEPERATE SYSTEMS |
| | REQUIRED. |
| | |
| | 3. SHEET A-7 SCUPPER HEAD AND LEADER DETAIL: ONE PART |
| | OF THE DETAIL INDICATES A 4" X 4" GALV. MET. DOWN |
| | LEADER, AND ANOTHER PART OF THE DETAIL INDICATES LEADER |
| | BEING 8", PLEASE CORRELATE THIS DETAIL FOR THE |
| | RESUBMITTAL SIZING THEM WITH THE TABLES FROM COMMENT |
| | #2. |
| | |
| | 4. SHEET A-7 SCUPPER HEAD AND LEADER DETAIL: DETAIL |
| | FAILS TO INDICATE SIZE OF SCUPPERS PER FBC-2004 |
| | PLUMBING SEC.1106.7, AND THERE IS NOT A DETAIL OF THE |
| | SECONDARY ROOF DRAIN SYSTEM PER FBC-2004 PLUMBING, SEC. |
| | 1107.2. PLEASE REVISE THE DETAIL FOR THE RESUBMITTAL. |
| | |
| | ************IMPORTANT INFORMATION |
| | IN ORDER TO EXPIDITE PLAN REVIEW: WHEN RESUBMITTING, |
| | PLEASE REPLACE ONLY SHEETS |
| | WHICH HAVE CHANGED AND PROVIDE ONE COPY |
| | OF ALL OLD/VOIDED SHEETS FOR REFERENCE |
| | ONLY. |
| | |
| | END OF COMMENTS: |
| | |
| | REVIEW BY MIKE PERSON |
| | (561) 805-6730 |
| | FAX (561) 805-6731 |
| | E-MAIL [email protected] |
| | UNDER SUPERVISION OF K.STEVENS |
| | (561) 805-6721 |
| | |
| | |
| | |
