| Date |
Text |
| 2006-10-28 11:23:11 | DENIED |
| | REFERENCE: |
| | FBC-2004 PLUMBING |
| | FBC-2004 CHAPTER 1 |
| | FBC-2004 CHAPTER 11 |
| | FLORIDA ADMINISTRATIVE CODE |
| | FLORIDA STATUTES |
| | MUNICIPAL CODE |
| | |
| | 1. ALL ARCHITECTURAL SHEETS. THE BUSINESS LICENSE |
| | NUMBER IS REQUIRED IN THE TITLE BLOCK PER FAC |
| | 61G1-16.004(2) & FS 481.2055. |
| | |
| | 2. ALL M,E,P SHEETS. SEAL REQUIRED TO BE AN EMBOSSING |
| | TYPE SEAL, AND THE SEAL SHALL CONTAIN THE WORD |
| | "LICENSE" EFFECTIVE FEBRUARY 5, 2004, BUT A GRACE |
| | PERIOD TO JANUARY 1, 2006 WAS GIVEN. PLEASE CHANGE SEAL |
| | AND MAKE SURE IT IS A RAISED, IMPRESSION TYPE SEAL. |
| | (SEE ATTACHED SHEET)FAC 61G15-23.001 & FS 471.025. |
| | |
| | 3. ALL M,E,P SHEETS. A CERTIFICATE OF AUTHORIZATION IS |
| | REQUIRED FOR THE ENGINEERING COMPANY PER FAC |
| | 61G15-23.002(2) & FS 471.025. - THE SIGNATURE OF THE |
| | ENGINEER IS REQUIRED ON THE SEAL. IT APPEARS TO BE AN |
| | INITIAL AND NOT A SIGNATURE. PLEASE PROVIDE A SIGNED, |
| | SEALED, DATED, NOTORIZED LETTER INDICATING THE LEGAL |
| | SIGNATURE OF THE ENGINEER FOR OUR FILES. FAC |
| | 61G15-23.002(1) & FS 471.025. |
| | |
| | 4. SHT A3.4 SHOW COMPLIANCE WITH THE FOLLOWING: |
| | 11-4.16.5 FLUSH CONTROLS, 11-4.18.4 FLUSH CONTROLS, |
| | 11-4.19.2 CLEARANCES, 11-4.19.4 EXPOSED PIPES & |
| | SURFACES, 11-4.19.5 FAUCETS. |
| | |
| | 5. SHT P1.1 FIXTURE CONNECTION SCHEDULE. FLOOR DRAINS |
| | ARE NOT APPROVED INDIRECT WASTE RECEPTORS. EITHER A |
| | FLOOR SINK OR A HUB DRAIN IS REQUIRED FOR THE INDIRECT |
| | WASTE FROM THE ICE MAKER, P-11. PLEASE CORRECT |
| | REFERENCE, AND IF SHOWN ON THE FLOOR PLAN AND THE SANT. |
| | RISER DIAGRAM, CHANGE THOSE ALSO. SECTIONS 802.3 & |
| | 802.3.2. |
| | |
| | 6. SHT P3.1 THE SAND/OIL INTERCEPTOR SHALL BE SIZED AND |
| | APPROVED BY THE UTILITY DEPT. CONTACT LYNN MASSON, |
| | ENVIRONMENTAL COMPLIANCE AT (561) 822-2271, OR FAX |
| | (561) 822-2279, OR E-MAIL [email protected]. WASTE ORD. |
| | 3434. |
| | |
| | 7. SHT P8.1 SANITARY RISER DIAGRAM. SUBMIT A SANITARY |
| | RISER DIAGRAM IN AN ISOMETRIC FORM THAT REFLECT THE |
| | FLOOR PLAN. SHOW ALL PIPE SIZES, VENTS, TRAPS AND |
| | INDICATE THE DRAINAGE FIXTURE UNITS AS THEY ACCUMULATE |
| | IN THE SYSTEM. SECTION 106.1.3. |
| | |
| | MAIN ENTRY: ISO?MET?RIC |
| | PRONUNCIATION: "I-S&-'ME-TRIK |
| | FUNCTION: ADJECTIVE |
| | 1 : OF, RELATING TO, OR CHARACTERIZED BY EQUALITY OF |
| | MEASURE; ESPECIALLY : RELATING TO OR BEING A |
| | CRYSTALLOGRAPHIC SYSTEM CHARACTERIZED BY THREE EQUAL |
| | AXES AT RIGHT ANGLES. |
| | |
| | 8. SHT P8.2 WATER RISER DIAGRAM. SUBMIT A WATER RISER |
| | DIAGRAM IN AN ISOMETRIC FORM THAT REFLECTS THE FLOOR |
| | PLAN. SHOW ALL PIPE SIZES, VALVES, AND WATER HAMMER |
| | ARRESTORS REQUIRED BY SECTION 604.9 LOCATED IN AN |
| | "EFFECTIVE RANGE" (NOT IN THE CEILING). SECTION |
| | 106.1.3. - FULL OPEN VALVES ARE REQUIRED ON ALL WATER |
| | DOWN-FEED LINES. SECTION 606.1(2). |
| | |
| | REVIEW BY KEN STEVENS |
| | (561) 805-6721 |
| | FAX (561) 805-6713 |
| | E-MAIL [email protected] |
