| Date |
Text |
| 2006-08-07 00:00:00 | ***** UNSAT ****** |
| | |
| | 1) NOTE: NO, PLEASE SEE RISER WAS NOT |
| | REVISED TO SHOW CONDUITS, PLEASE SEE ONE |
| | CONDUIT FROM THE METERCAN SEEM TO SHOW |
| | RUNNING THROUGH ONE ATS TO GET TO THE |
| | OTHER? PLEASE SEE PREVIOUS NOTES WITH |
| | REPECT TO USING THIS ATS AS A RACEWAY |
| | FOR SEC'S. |
| | |
| | ** PREVIOUS REVIEW NOTE ** |
| | PLEASE SEE RISER DOES NOT |
| | INDICATE THE CONDUITS FROM THE ATS'S TO |
| | THE EXISTING PANELS. MAY NOT RUN FEEDERS |
| | BACK THROUGH METER CAN. |
| | 230.7, 408 ETC. |
| | MAY NOT HAVE LINE AND LOAD IN THE SAME |
| | RACEWAY OR ENCLOSURE. |
| | PLEASE KNOW, RISER WILL SUBSTANTIALLY |
| | CHANGE FROM SUBMITTED PLANS. |
| | |
| | 2) NOTE:NO, PLEASE SEE A LAYOUT WAS |
| | PROIVIDED, HOWEVER PLEASE SEE MISSING |
| | DISCONNECTING MEANS FOR FEEDERS FROM |
| | GENERATOR. PLEASE SEE THIS DISCONNECT |
| | DOES NOT REQUIRE OCP, ONLY A DISCONNECT |
| | RATED FOR THE LOAD SERVED AND GROUPED |
| | WIHT THE EXISTING (NEW) MAINS. PLEASE |
| | SEE THIS MAY BE PALCED ON FEEDER CONDUIT |
| | BEFORE THE ATS OR TWO DISCOONECTS WOULD |
| | BE REQUIRED AFTER THE ATS GOING INTO |
| | HOUSE. A 200A RATED DISCONNECT SEEMS THE |
| | BEST OPTION, HOWEVER ONLY A SUGGESTION. |
| | |
| | ** PREVIOUS REVIEW NOTE ** |
| | PLEASE PROVIDE A LAYOUT FOR ALL |
| | SERVICE EQUIPMENT. PLEASE PROVIDE |
| | DISCONNECTING MEANS FOR THE FEEDER |
| | COMING FROM GEN. THIS NEED ONLY BE |
| | DISCONECT, DOES NOT REQUIRE OCP. THIS |
| | MAY BE ONE ON THE LINE SIDE OF ATS'S |
| | FROM GEN OR TWO DISCONNECTS ON THE LOAD |
| | SIDE OF THE ATS'S.PLEASE KNOW, IF THE |
| | EXISTING MCB PANELS ARE OUTSIDE GROUPED |
| | WITH THE NEW SE RATED ATS'S THEN A THE |
| | DISCONNECTING MEANS NOTED ABOVE WOULD |
| | NOT BE REQUIRED. (( PLEASE KNOW, THE |
| | BRKR ON GEN UNIT IS NOT ACCEPTABLE FOR |
| | THE REQUIRED MEANS OF DISCONNECT. |
| | ** THE SE RATED ATS'S ONLY DISCONNECT |
| | THE POWER FROM THE NORMAL/FPL SIDE. |
| | 225.31-225.39,110.27 ETC. |
| | |
| | 3) NOTE: NO, THIS INCLUDES LOAD |
| | CALCULATIONS SUBMITTED. |
| | |
| | ** PREVIOUS REVIEW NOTE** |
| | PLEASE KNOW, ALL PLANS SHALL |
| | BEAR THE PRINTED NAME AND THE SIGNATURE |
| | OF THE PERSON RESPONSIBLE FOR |
| | PLANS/DESIGN. |
| | FBC ADMIN SECT 106.1.2 |
| | |
| | 4) NOTE:OK, HOWEVER PLANS ARE BEING |
| | ROUTED TO ZONING FOR VERIFICATION OF SET |
| | BACK. |
| | |
| | ** PREVIOUS REVIEW NOTE** |
| | PLEASE KNOW, THE GEN WILL BE |
| | REQUIRED TO BE LOCATED A MIN OF 5' FROM |
| | THE DWELLING AND ANY OTHER SURROUNDING |
| | STRUCTURAL ELEMENTS. |
| | PLEASE KNOW, AS PER LETTER OBTAINED FROM |
| | GENERAC, THE MIN RECOMMENDED CLEARENCES |
| | FOR LIQUID COOLED UNITS IS 5FT. |
| | PLEASE SEE THAT MANUFACTURE SPECS |
| | SUBMITTED INDICATED THE MIN CLEARENCE. |
| | 110.3, |
| | ** PLEASE KNOW, THE SITE PLAN WHICH WAS |
| | STAMPED BY ZONING WILL NEED TO BE |
| | REVISED IF UNIT IS 5FT FROM DWELLING. |
| | |
| | ** NEW NOTE ** |
| | 5) NOTE: PLEASE SEE TWO SMALL APPL |
| | CIRCUITS ARE BEING INDICATED, HOWEVER |
| | SHOWS 3500 VA. PLEASE SEE 220.16 (1500VA |
| | EACH). |
| | PLEASE ALSO SEE 220.18 AS THE MIN VA TO |
| | BE FIGURED FOR ELEC DRYERS ARE 5000VA |
| | PLEASE ADJUST CALCULATIONS. |
| | |
| | |
| | PLEASE SUBMIT THE ABOVE INFORMATION FOR |
| | REVIEW. IF THERE ARE ANY QUESTIONS, |
| | PLEASE DO NOT HESITATE TO CALL. |
| | |
| | DEWEY PALMER |
| | ELECTRICAL PLAN REVIEW |
| | CITY OF WEST PALM BEACH |
| | CONSTUCTION SERVICES DEPT. |
| | 561-805-6717 |
| | [email protected] |
