City of West Palm Beach eGovPlus

Plan Review Notes

Plan Review Notes For Permit 04090764
Permit Number	04090764
Review Stop	B
Sequence Number	1

Notes

Date	Text
2004-11-09 00:00:00	DENIED

	1)IMPACT FEES MUST BE PAID TO PALM
	BEACH COUNTY, PLANS STAMPED BY THEM AND
	COPY OF RECEIPT SUBMITTED TO CITY OF
	WEST PALM BEACH BUILDING DEPARTMENT,
	BEFORE A BUILDING PERMIT CAN BE ISSUED.


	2)A RECORDED COPY OF THE NOTICE OF
	COMMENCEMENT MUST BE SUBMITTED BEFORE A
	PERMIT CAN BE ISSUED.


	3) FBC* 1804.2.2AREA OF QUESTIONABLE
	SOIL.SUBMIT A GEOTECHNICAL REPORT
	TO VERIFY THE SAFE BEARING CAPACITY OF
	THE SOIL.

	4) THE WINDOW (G) IN BEDROOM #2 IS
	SPECIFIED AS A 2' X 4' CASEMENT WINDOW
	ON THE SCHEDULE ON A9. VERIFY THAT THIS
	WILL MEET THE CLEAR OPENING REQUIREMENTS
	OF FBC 1005.4.

	5) FBC 2405.2 REQUIRES SAFETY GLAZING IN
	WINDOWS WITHIN 3' HORIZONTALLY AND LESS
	THAN 60" ABOVE THE WALKING OR STANDING
	SURFACES AT TUBS OR SHOWERS. PLEASE
	SPECIFY ON THE PLANS THAT THE WINDOWS IN
	THE MASTER BATH AND BATH #1 AT THE
	SHOWER ARE TO HAVE SAFETY GLAZING IF
	THEY ARE WITHIN THESE AREAS.

	6) 61G-16.004 OF THE FAC REQUIRES THE
	PRINTED NAME OF THE PERSON SEALING THE
	DOCUMENT ON EACH PLAN SHEET.

	7) SPECIFY THE LOCATION AND THE MINIMUM
	SIZE OF THE ATTIC ACCESSES AS REQUIRED
	BY FBC 2309.6.

	8) THE NOTE ON A8 SPECIFIES ATTIC
	VENTILATION AND THE WALL SECTIONS ON A11
	SPECIFY AN ICYNENE FOAM INSULATION
	SYSTEM WHICH IS VENTLESS. PLEASE
	CLARIFY. SPECIFY THE NUMBER SIZE AND
	SPACING OF ATTIC VENTS OR SUBMIT THE
	DESIGN DRAWINGS FROM A FLORIDA
	REGISTERED DESIGN PROFESSIONAL, THE
	ICYNENE SPECIFICATIONS FROM THE
	MANUFACTURER AND AN AFFIDAVIT CERTIFYING
	THE USE OF THE ASPHALT BASED ROOFING
	PRODUCTS OVER AN UNVENTED SYSTEM.
	SPECIFY THE R-VALUE OF THE INSULATION.

	9) PROVIDE DETAILS OF THE FLAT ROOFS AND
	INDICATE HOW DRAINAGE WILL BE ACHIEVED.

	10) REVISE THE BOTTOM RAIL NOTE ON A10
	TO STATE FLOOR OR DECK AND NOT ROOF.

	11) SPECIFY THE RISER HEIGHTS AND TREAD
	DEPTHS FOR THE STAIRS. SPECIFY THE

	12) SPECIFY THE EMBED DEPTH OF THE
	EXPANSION BOLTS AT THE TOP OF THE GARAGE
	DOOR BUCKS ON A10.

	13) SHOP DRAWINGS WILL BE REQUIRED TO BE
	SUBMITTED FOR APPROVAL FOR THE SECOND
	FLOOR SYSTEM.

	14) THE BUCK DETAILS ON A10 CONFLICT
	WITH THE BUCK FASTENING DETAILS ON S4.
	PLEASE CORRECT.

	15) BUCK DETAILS ON A10 SPECIFY 2-1/2"
	TAPCONS WITH 1-1/2" EMBED THROUGH A 2X
	BUCK. THIS IS NOT POSSIBLE. PLEASE
	CORRECT.

	16) SUBMIT DETAILS FOR FIREPLACE AND
	CHIMNEY CONSTRUCTION. SHOW DIMENSIONS,
	HEIGHT ABOVE ROOF AND COMPLIANCE WITH
	FBC 2113, 2114, 2804 & 2806.

	17) SUBMIT CUT SHEETS FOR THE ELEVATOR.
	SPECIFY LOCATION OF ELEVATOR EQUIPMENT,
	GUIDE RAIL ATTACHMENTS, ETC.

	18) THE BEAM SCHEDULE ON S3 HAS 2 NOTE
	B. ONE SHOULD BE NOTE C. PLEASE
	CORRECT.

	19) PRODUCT APPROVALS SUBMITTED WITH
	PERMIT APPLICATION AFTER OCTOBER 1, 2003
	ARE REQUIRED TO COMPLY WITH THE FLORIDA
	PRODUCT APPROVAL SYSTEM. FOR INFORMATION
	PLEASE SEE THE STATE WEBSITE AT
	WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
	STATEWIDE APPROVAL ARE REQUIRED TO BE
	SUBMITTED WITH A COVER SHEET THAT LISTS
	THE PRODUCT IDENTITY NUMBER FROM THE
	STATE. IF THE PRODUCT DOES NOT HAVE
	STATEWIDE APPROVAL, SUBMIT AN APPLICA-
	TION FOR LOCAL PRODUCT APPROVAL OR SITE
	SPECIFIC FORM PER RULE 9B-72.
	SUBMIT PRODUCT APPROVALS FOR THE
	FOLLOWING:
	- TRUSS CONNECTORS
	- CUSTOM MAHOGANY ENTRY DOORS
	- ARCHED TOP FRENCH DOORS WITH AND
	WITHOUT SIDELITES
	- RADUIS CASEMENT WINDOWS
	- HOPPER WINDOW
	- SLIDING GLASS DOOR

	23) THE PRODUCT APPROVAL INSTALLATION
	DRAWINGS FOR THE CLOPAY GARAGE DORRS ARE
	ILLEGIBLE. SUBMIT LEGIBLE COPIES.

	24) SOME OF THE NOAS THAT WERE SUBMITTED
	ARE NOT THE CORRECT ONES FOR THE FLORIDA
	PRODUCT APPROVALS THAT WERE GIVEN.
	PLEASE SUBMIT THE CORRECT NOAS OR OTHER
	EVALUATION LISTED ON THE STATE WEB
	SITE.

	IF YOU HAVE ANY QUESTIONS PLEASE CALL:



	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714