| Date |
Text |
| 2004-10-19 00:00:00 | DENIED |
| | |
| | 1) IMPACT FEES MUST BE PAID TO PALM |
| | BEACH COUNTY, PLANS STAMPED BY THEM AND |
| | COPY OF RECEIPT SUBMITTED TO CITY OF |
| | WEST PALM BEACH BUILDING DEPARTMENT, |
| | BEFORE A BUILDING PERMIT CAN BE ISSUED. |
| | |
| | 2) A RECORDED COPY OF THE NOTICE OF |
| | COMMENCEMENT MUST BE SUBMITTED BEFORE A |
| | PERMIT CAN BE ISSUED. |
| | |
| | 3) THE ORIGINAL WET SIGNATURE AND TITLE |
| | BLOCK WITH NAME, ADDRESS AND LICENSE |
| | NUMBER IS REQUIRED ON EACH SHEET. SEE |
| | 61G15-23.002. |
| | |
| | 4) PROTECTION FROM TERMITES IS REQUIRED |
| | BY FBC 1816. PLEASE SPECIFY ON THE PLANS |
| | |
| | 5) FBC TABLE 1606.2B INDICATES THAT THE |
| | NEGATIVE WINDOW LOAD PRESSURE FOR THE |
| | 25SH WINDOWS (ZONE 4) WILL BE MORE THAN |
| | THE -36 PSF SPECIFIED ON THE PLANS. |
| | PLEASE CORRECT. |
| | |
| | 6) SPECIFY THE SIZE OF THE ATTIC ACCESS |
| | ON THE PLANS. SEE FBC 2309.6. |
| | |
| | 7) THE OWNER/AGENT IS REQUIRED TO SIGN |
| | THE ENERGY CALCULATION FORM. FBC CH.13. |
| | |
| | 8)FL. BLD CODE 1606.1.7 THE FOLLOWING |
| | INFORMATION RELATED TO WIND SHALL BE |
| | SHOWN ON THE CONSTRUCTION DRAWINGS, |
| | 1)- BASIC WIND SPEED, MPH |
| | 2)- WIND IMPORTANCE FACTOR, & BUILDING |
| | CATEGORY |
| | 3)- WIND EXPOSURE |
| | 4)- INTERNAL PRESSURE COEFFICIENT, |
| | 5)- COMPONENTS & CLADDING, THE DESIGN |
| | WIND PRESSURES IN TERMS OF PSF. |
| | |
| | 9) STRUCTURAL NOTE #1 ON SHEET 5 SHOULD |
| | BE CHANGED FROM 120MPH TO 140 MPH FOR |
| | WIND SPEED WITHIN THE CITY OF WPB. SEE |
| | FBC 1606.1.6. |
| | |
| | 10) SPECIFY THAT THE NAILING NOTE ON |
| | SHEET 6 IS FOR ROOF SHEATHING. |
| | |
| | 11) NOTE 12 ON SHEET 5 CALLS FOR 10D |
| | NAILS WHICH CONFLICTS WITH THE NOTE ON |
| | SHEET 6 WHICH SPECIFIES 8D NAILS. PLEASE |
| | CORRECT. |
| | |
| | 12)USP WUSC 24 GIRDER TIES ARE SPECIFIED |
| | ON THE TRUSS LAYOUT ON SHEET 6. THESE |
| | ARE FOR ANCHORING TO WOOD FRAME, BUT |
| | ARE INDICATED IN AREAS THAT ARE MASONRY |
| | CONSTRUCTION. PLEASE CORRECT. |
| | |
| | 13) SPECIFY THE TRUSS LOADS ON THE PLANS |
| | INCLUDING THE BOTTOM CORD LIVE LOAD, |
| | WHICH IS REQUIRED TO BE A MINIMUM OF |
| | 10 PSF. SEE FBC TABLE 1604.1. |
| | |
| | 14) SPECIFY THE MAXIMUM SPACING OF THE |
| | REINFORCED VERTICAL FILLED CELLS ON THE |
| | FOUNDATION PLAN. |
| | |
| | 15) SPECIFY THE FOOTING SIZE AND REBAR |
| | FOR THE COLUMNS AT THE DEN FRONT. |
| | |
| | 16) THE DEN FRONT DETAIL ON SHEET 6 |
| | SPECIFIES ONE #5 IN THE NOTES, BUT THE |
| | DRAWINGS SHOW 3 REBARS ON SHEETS 6 & 7. |
| | PLEASE CORRECT. |
| | |
| | 17) SPECIFY THE EMBED DEPTH OF THE 1/2" |
| | RED HEAD ANCHORS ON THE DEN FRONT DETAIL |
| | ON SHEET 6. |
| | |
| | 18) SOME OF THE PLAN SHEETS THAT WERE |
| | SUBMITTED ARE ILLEGIBLE AND NOT CLEAR |
| | DRAFTSMAN QUALITY PLANS. PLEASE SUBMIT |
| | CLEAR READABLE PLANS. |
| | |
| | 19) SPECIFY THE WINDOW TYPE AND SIZES |
| | FOR THE BEDROOM AND FAMILY ROOM. |
| | |
| | 20) SUBMIT A KEY PLAN AND INSTALLATION |
| | SCHEDULE FOR THE STORM PANELS. SPECIFY |
| | THE ANCHOR TYPES, SPACINGS AND TYPE OF |
| | MOUNTING THAT WILL BW USED. SUBMIT |
| | COMPLETE PRODUCT APPROVALS AND INSTALL- |
| | ATION DRAWINGS WITH THE STATE PRODUCT |
| | APPROVAL NUMBER. |
| | |
| | 21) PRODUCT APPROVALS SUBMITTED WITH |
| | PERMIT APPLICATION AFTER OCTOBER 1, 2003 |
| | ARE REQUIRED TO COMPLY WITH THE FLORIDA |
| | PRODUCT APPROVAL SYSTEM. FOR INFORMATION |
| | PLEASE SEE THE STATE WEBSITE AT |
| | WWW.FLORIDABUILDING.ORG. PRODUCTS WITH |
| | STATEWIDE APPROVAL ARE REQUIRED TO BE |
| | SUBMITTED WITH A COVER SHEET THAT LISTS |
| | THE PRODUCT IDENTITY NUMBER FROM THE |
| | STATE. IF THE PRODUCT DOES NOT HAVE |
| | STATEWIDE APPROVAL, SUBMIT AN APPLICA- |
| | TION FOR LOCAL PRODUCT APPROVAL OR SITE |
| | SPECIFIC FORM PER RULE 9B-72. |
| | |
| | 22) SUBMIT STATE PRODUCT APPROVALS FOR |
| | THE FOLLOWING: DOUBLE OUTSWING FRONT |
| | DOOR, SLIDING GLASS DOORS, FIXED EYEBROW |
| | WINDOWS AND STRUCTURAL MULLIONS. |
| | |
| | 23)THE PLANS SPECIFY FIBERGLASS SHINGLES |
| | ON THE WALL SECTION ON SHEET 5. HOWEVER, |
| | THE PRODUCT APPROVAL SUBMITTED IS FOR |
| | CEMENT ROOF TILES. PLEASE SUBMIT THE |
| | APPROPRIATE PRODUCT APPROVAL OR REVISE |
| | THE PLANS. TWO COMPLETE SETS OF PRODUCT |
| | APPROVALS WITH STATE COVER SHEETS ARE |
| | REQUIRED. |
| | |
| | IF YOU HAVE ANY QUESTIONS PLEASE CALL: |
| | ROBERT MCDOUGAL |
| | BLDG. PLAN REVIEW |
| | (561)805-6714 |
