| Date |
Text |
| 2004-03-24 00:00:00 | DENIED |
| | REFERENCE: FBC-2001 PLUMBING |
| | FBC-2001 CHAPTER 1 |
| | FBC-2001 CHAPTER 11 |
| | FLORIDA ADMINISTRATIVE CODE |
| | FLORIDA STATUTES |
| | |
| | 1) PER TABLE 403.1 A DRINKING FOUNTAIN |
| | IS REQUIRED. |
| | 2) SHT A-2 ALL CAPPED AND DEMO'ED PLUMB- |
| | ING LINES SHALL BE INSPECTED PRIOR TO |
| | COVERING. |
| | 3) SHT A-3 SPECIFICATION WORK SHEETS RE- |
| | FERED TO BY DBPR STAMP (3) SHALL BE SUB- |
| | MITTED. 1 COPY WITH EACH SET OF PLANS. |
| | SECTION 104.2.1 |
| | 4) SHTS A-3 & P-1 FIXTURE SCHEDULE, X5A |
| | SHOWS QUANTITY 2, NONE FOUND. PLEASE |
| | CLAIRFY. SECTION 104.2.1 |
| | 5) SHT A-3 S-13 GREASE INTECEPTOR NOT |
| | APPROVED UNDER SINK. CONTACT RODNEY |
| | COMPO, ENVIRONMENTAL COMPLIANCE, WASTE |
| | ORD. 2938-96 @ (561) 837-4074 FOR GREASE |
| | INTECEPTOR REQUIREMENTS. |
| | 6) SHT P-2 WATER RISER DIAGRAM, WATER |
| | HAMMER ARRESTORS SHALL BE LOCATED NEAR |
| | THE FIXTURE IN AN "EFFECTIVE RANGE" NOT |
| | IN THE CEILING AS SHOWN. PDI-WH 201 AND |
| | MANUF. INSTALLATION INSTRUCTIONS. SECT- |
| | ION 604.9 |
| | 7) SHT P-3 PLUMBING SPECIFICATIONS #7, |
| | AIR CHAMBERS ARE NOT APPROVED. DELETE |
| | FROM REFERENCE. PDI-WH 201/SECTION 604.9 |
| | 8) AN RPZV BACKFLOW IS REQUIRED ON THE |
| | WATER SERVICE TO THIS SPACE. INSTALLED |
| | A MAXIMUM OF 4' ABOVE THE FLOOR FOR |
| | SERVICING AND CERTIFICATION. SECTION |
| | 608.13.2 |
| | 9) SHT P-3 WATER HEATER DETAIL, THERMAL |
| | EXPANSION CONTROL REQUIRED PER SECTION |
| | 607.3.2 |
| | 10) PROFESSIONAL ENGINEER SHALL SIGN HIS |
| | NAME AND AFFIX HIS SEAL TO ALL PLANS, |
| | SPECIFICATIONS, REPORTS AND FINAL BID |
| | DOCUMENTS PROVIDED TO THE OWNER OR THE |
| | OWNER'S REPRESENTATIVE, OR OTHER DOCU- |
| | MENTS PREPARED OR ISSUED BY SAID REGIS- |
| | TRANT AND BEING FILED FOR PUBLIC RECORD. |
| | THE DATE THAT THE SIGNATURE AND SEAL IS |
| | AFFIXED AS PROVIDED HEREIN SHALL BE EN- |
| | TERED ON SAID PLANS, SPECIFICATIONS, RE- |
| | PORTS, OR OTHER DOCUMENTS IMMEDIATELY |
| | UNDER THE SIGNATURE OF THE PROFESSIONAL |
| | ENGINEER, FAC 61G15-23.002(1) |
| | FS 471.025 - INITIALS ARE NOT ACCEPTABLE |
| | EACH SHEET OF PLANS AND PRINTS WHICH |
| | MUST BE SEALED UNDER THE PROVISIONS OF |
| | CHAPTER 471 SHALL BE SEALED, SIGNED AND |
| | DATED BY THE PROFESSIONAL ENGINEER IN |
| | RESPONSIBLE CHARGE. FAC 61G15-23.002(2) |
| | FS 471.025 |
| | ENGINEERS SHALL LEGIBLY INDICATE THEIR |
| | NAME, ADDRESS AND LICENSE NUMBER ON EACH |
| | SHEET. IF PRACTICING THROUGH A DULY |
| | AUTHORIZED ENGINEERING BUSINESS, ENGIN- |
| | EERS, ENGINEERS SHALL LEGIBLY INDICATE |
| | THEIR NAME AND LICENSE NUMBER, AS WELL |
| | AS, THE NAME, ADDRESS AND CERTIFICATE OF |
| | AUTHORIZATION NUMBER OF THE ENGINEERING |
| | BUSINESS ON EACH SHEET. A TITLE BLOCK |
| | WILL SATISFY THIS REQUIREMENT. FAC |
| | 61G15-23.002(2) - FS 471.025 |
| | THE SEAL SHALL BE PRESSED SO THAT IT CAN |
| | BE READ. UNABLE TO READ NAME OF ENGINEER |
| | AND TYPE OF PROFESSIONAL. |
| | |
| | REVIEW BY KEN STEVENS |
| | (561) 805-6721 |
| | FAX (561) 653-2692 |
| | E-MAIL [email protected] |
