| Date |
Text |
| 2002-10-31 00:00:00 | |
| | BUILDING DENIED |
| | |
| | 1) IMPACT FEES MUST BE PAID TO PALM |
| | BEACH COUNTY, PLANS STAMPED BY THEM AND |
| | COPY OF RECEIPT SUBMITTED TO CITY OF |
| | WEST PALM BEACH BUILDING DEPARTMENT, |
| | BEFORE A BUILDING PERMIT CAN BE ISSUED. |
| | |
| | 2) A RECORDED COPY OF THE NOTICE OF |
| | COMMENCEMENT MUST BE SUBMITTED BEFORE A |
| | PERMIT CAN BE ISSUED. |
| | |
| | 3) PROVIDE A COMPLETE SOIL TEST REPORT |
| | INDICATING SOIL PREPARATION AND SOIL |
| | BEARING CAPACITY. REPORT SHALL HAVE THE |
| | WET SIGNATURE, DATE AND EMBOSSED SEAL |
| | OF A FL SOIL ENGINEER. |
| | |
| | 4) PLEASE REVISE THE CONSTRUCTION TYPE |
| | LISTED ON A4 TO TYPE VI. |
| | |
| | 5) SPECIFY THAT THE WWM FOR THE SLAB |
| | SHALL BE SUPPORTED BY APPROVED APPROVED |
| | MATERIALS OR SUPPORTS AT SPACINGS NOT TO |
| | EXCEED 3 FEET. SEE 2001 FBC SEC. 1909.3. |
| | |
| | 6)THE EXPOSURE CATEGORY FOR THE |
| | STRUCTURE GIVEN ON A1 IS B NOT C. |
| | PLEASE REVISE. |
| | |
| | 7) SPECIFY ONE HOUR FIRE RATED GLASS |
| | BLOCK AT ZERO LOT LINE. REVISE THE GLASS |
| | BLOCK DETAIL ON A8 TO SHOW A ONE HOUR |
| | RATED GLASS BLOCK ASSEMBLY. |
| | |
| | 8) PROVIDE A LINTEL SCHEDULE. |
| | |
| | 9) THE GLASS BLOCK IN THE MASTER BATH |
| | ARE IN HAZARDOUS LOCATIONS AND MUST HAVE |
| | A MINIMUM UNIFORM FACE THICKNESS OF 0.25 |
| | INCH PER FBC 2405.2.2. SPECIFY THIS ON |
| | THIS ON THE PLANS. |
| | |
| | 10) PROVIDE COMPLETE INFORMATION FOR THE |
| | 2" STEEL HEADER DETAIL. INDICATE THE |
| | WELD TYPE, THICKNESS OF STEEL, ETC. |
| | |
| | 11) PLEASE CORRECT THE CONSTRUCTION TYPE |
| | LISTED ON A4 TO TYPE VI. |
| | |
| | 12) PROVIDE CALCULATIONS WHICH INDICATE |
| | THAT THE REQUIRED NET FREE VENTILATING |
| | AREA WILL BE PROVIDED BY THE AREAS THAT |
| | DO NOT HAVE THE STYROFOAM TRIM. |
| | |
| | 13) SPECIFY THE SIZE OF THE WASHERS USED |
| | ON THE TAPCONS FASTENING THE GARAGE DOOR |
| | BUCKS IN THE DETAIL ON A8. |
| | |
| | 14) REVISE THE SWING DOOR BUCK DETAIL ON |
| | A8 TO COMPLY WITH FBC 1707.4.4.2. |
| | |
| | 15) PROVIDE A STRUCTURAL DETAIL OF THE |
| | BOLLARD/3" STEEL POST IN THE GARAGE. |
| | |
| | 16) SPECIFY ON THE PLANS THAT THE DOOR |
| | BETWEEN THE GARAGE AND CONDITIONED SPACE |
| | IS SOLID CORE OR INSULATED AS REQUIRED |
| | BY CHAPTER 13 OF THE FBC. |
| | |
| | 17) PROVIDE (2) COPIES OF A KEY PLAN AND |
| | INSTALLATION SCHEDULE INDICATING THE |
| | SPECIFIC TYPE OF FASTENERS THAT ARE TO |
| | BE USED FOR THE STORM PANELS. INDICATE |
| | THE MOUNTING OPTIONS THAT WILL BE USED. |
| | THIS INFORMATION IS REQUIRED PRIOR TO |
| | PERMIT OR A SEPARATE PERMIT WILL BE |
| | REQUIRED WITH ADDITIONAL FEES. |
| | |
| | 18) THE PRODUCT APPROVALS FOR THE |
| | SLIDING GLASS DOORS IS MISSING PAGE 2 |
| | AND THE DRAWINGS HAVE THE WRONG |
| | ACCEPTANCE NUMBER. |
| | |
| | 19) PROVIDE MANUFACTURES SPECS. AND UL |
| | LISTING INFORMATION FOR ONE HOUR RATED |
| | GLASS BLOCK ASSEMBLIES. |
| | |
| | 20) PRODUCT APPROVALS WERE SUBMITTED FOR |
| | GLASS BLOCK FROM TWO DIFFERENT MANUFACT- |
| | URERS. SUBMIT THE ONE THAT IS TO BE |
| | INSTALLED ALONG WITH THE INFORMATION |
| | REQUESTED ABOVE AN THAT CORRESPONDS TO |
| | THE DETAIL ON THE PLANS. |
| | |
| | 21) IN ORDER TO MEET THE WINDLOAD |
| | PRESSURES LISTED ON THE PLANS, THE FIXED |
| | GLASS WINDOWS WILL HAVE TO BE TEMPERED |
| | GLASS ACCORDING TO THE PRODUCT APPROVALS |
| | THAT WERE SUBMITTED. SPECIFY ON THE |
| | PLANS THAT THESE WINDOWS WILL HAVE |
| | TEMPERED GLASS. |
| | |
| | 22) THE SITE SPECIFIC PRODUCT APPROVALS |
| | FOR THE SIDE SWINGING DOORS ARE REQUIRED |
| | TO BE SIGNED, SEALED AND DATED BY THE |
| | DESIGNER OF RECORD OF THE STRUCTURE. THE |
| | LOCATION OF THE STRUCTURE IS REQUIRED TO |
| | BE ON THE FORM. PROVIDE THE TEST REPORTS |
| | FOR MISSLE IMPACT AS REQUIRED BY GENERAL |
| | NOTE 7.5 ON THE FORM. |
| | |
| | 23) THE DESIGN PRESSURES LISTED ON THE |
| | PLANS FOR SOME OF THE SINGLE HUNG |
| | WINDOWS EXCEED THE DESIGN PRESSURES IN |
| | THE PRODUCT APPROVALS. SOME WILL REQUIRE |
| | TEMPERED GLASS TO COMPLY. |
| | |
| | 24) PROVIDE PRODUCT APPROVALS FOR |
| | STRUCTURAL MULLIONS AT WINDOWS. |
| | |
| | ROBERT MCDOUGAL |
| | BLDG. PLAN REVIEW |
| | (561)659-8096 EXT.8202 |
