| Date |
Text |
| 2002-11-04 00:00:00 | CHECKLIST: |
| | 1-NEED RECORDED NOTICE OF COMMENCEMENT. |
| | 2-IMPACT FEES: NEED STAMPED DRAWINGS AND |
| | PAID RECEIPT. |
| | 3-PRELIMINARY SOIL REPORT SHOWS ORGANIC |
| | SOIL. REMOVE AS REQUIRED PER SECTION |
| | 1804.108 FBC 2001. |
| | PROVIDE SOIL REPORT AT THIS LOT SHOW'G |
| | LOT PREPARATION AND BEARING CAPACITY. |
| | SEC. 104.2.1.2 CITY AMENDMENTS TO FBC. |
| | 4-INTERNAL PRESSURE COEFFICIENT GIVEN IN |
| | SHEET A1 SHALL BE GIVEN WITH PLUS AND |
| | MINUS SIGNS FOR PRESSURES ACTING |
| | TOWARD AND AWAY FROM THE INTERNAL |
| | SURFACES. SEE TABLE 6-7 ASCE 7-98. |
| | 5-CLARIFY HOW'S THE GARAGE STEEL BOLLARD |
| | DETAIL DESIGNED TO PROVIDE VEHICLE IM- |
| | PACT PROTECTION TO A/C EQUIPMENT GIVEN |
| | THE SPECS SHOWN ON DETAIL ON SHEET A13 |
| | SEC. 104.2.1.2 CITY AMENDMENTS TO FBC. |
| | 6-PROVIDE COMPLETE STRUCTURAL DETAIL AND |
| | SPECS FOR 4X8 SOLID LINTEL FOR DOORS |
| | AND WINDOWS ASSEMBLIES WITH TRANSOM |
| | ABOVE AS SHOWN ON PLANS. SEC 104.2.1.2 |
| | CITY AMENDMENTS TO FBC 2001. |
| | **OR PROVIDE PRODUCT APPROVAL SHOWING |
| | COMPLETE ASSEMBLIES AS SHOWN ON PLANS. |
| | 7-PROVIDE ATTIC ACCESS AT SECOND FLOOR |
| | ROOF. SEC. 2309.6 FBC 2001. |
| | 8-SPECIFY SAFETY GLASS FOR WINDOWS AT |
| | MASTER BATH AND BATH #2. SEC 2405.2 |
| | FBC 2001. |
| | 9-PROVIDE COMPLETE STRUCTURAL SECTION AT |
| | REAR PORCH SHOWING STRUCTURAL INSTALLA |
| | TION OF RAILING THAT COMPLIES WITH |
| | SEC. 1608.2 FBC 2001. |
| | SEC. 104.2.1.2 CITY AMENDMENTS TO FBC. |
| | 10-REVISE TITLE OF DRAWING IN SHEET A7. |
| | THIS IS THE 2ND FLOOR FRAMING PLAN NOT |
| | 1ST FLOOR FRAMING PLAN. |
| | 11-REVISE NAILING SCHEDULE FOR ROOF |
| | SHEATHING. NEED MIN 8D RING SHANK AT |
| | MEAN ROOF HEIGHT GREATER THAN 25'. |
| | SEE TABLE 2306.1 CITY AMENDMENTS TO |
| | FBC 2001. |
| | 12-STEEL HEADER DETAIL. A)CLARIFY SIZE |
| | ON DETAIL SHOWN ON SHEET A13: 2"X6"X |
| | 1-1/4"?. B)SEE SIZE OF MULLIONS SPEC- |
| | FIED ON PLANS. C)SEE SECTION 1707.4.5 |
| | FBC 2001 FOR REQUIREMENTS NEEDED FOR |
| | THE DESIGN OF MULLIONS AND PROVIDE ALL |
| | INFORMATION AS REQUIRED. |
| | 13-SPECIFY SIZE OF WASHER AT STRUCTURAL |
| | GARAGE BUCK DETAIL. SEC. 104.2.1.2 |
| | CITY AMENDMENTS TO FBC 2001. |
| | 14-REVISE DETAIL FOR SWING DOOR JAMB. |
| | SEE SEC. 1707.4.4.2 FBC 2001. |
| | 15-STORM SHUTTERS; A) PROVIDE COMPLETE |
| | KEY PLAN AND INSTALLATION SCHEDULE. |
| | SEE CITY SAMPLE. |
| | B)PROVIDE DADE COUNTY OR SBCCI PRODUCT |
| | APPROVAL OR PROVIDE COMPLETE INFORMA- |
| | TION FOR SITE SPECIFIC INSTALLATION. |
| | SEE CITY IMPLEMENTATION STANDARD FOR |
| | HURRICANE MISSILE IMPACT PROTECTION. |
| | C)CLEARLY INDICATE ON DRWGS THE SPECIFIC |
| | MOUNTING CONDITIONS AND ANCHOR TYPE & |
| | SPACING TO BE USED (SEE INSTALLATION |
| | SCHEDULE ON STORM PANEL DWGS). |
| | 16-CLARIFY WHICH GLASS BLOCK COMPANY IS |
| | GOING TO BE USED. THERE ARE TWO DIFFE- |
| | RENT COMPANIES SUBMITTED. ****NOTE: |
| | ONLY ONE OF THEM MEET THE DESIGN PRE- |
| | SSURES CALCULATED BY THE ARCHITECT. |
| | **ALSO, UL SPECIFICATIONS FOR ONE HOUR |
| | FIRE RATED ASSEMBLY. |
| | **PROVIDE INFORMATION SHOWING FACE THICK |
| | NESS OF GLASS BLOCK TO VERIFY IF SAFE- |
| | TY GLASS IS REQUIRED. SEC. 2405.2.2 |
| | FBC 2001. |
| | 17-SWING DOORS: THIS BUILDING DEPARTMENT |
| | DOESN'T ACCEPT BROWARD COUNTY PRODUCT |
| | APPROVALS. ***NOTE: ALSO, THEY DON'T |
| | MEET THE DESIGN PRESSURES CALCULATED |
| | BY THE ARCHITECT. |
| | 18-FIXED WINDOWS: SOME WINDOWS DON'T |
| | MEET THE DESIGN PRESSURES CALCULATED |
| | BY THE ARCHITECT.***NOTE: PRODUCT |
| | APPROVAL TO SPECIFY HOW ARE WINDOWS TO |
| | BE ATTACHED TO STEEL TRANSOM. |
| | 19-SLIDING GLASS DOORS PRODUCT APPROVAL |
| | AND DRAWINGS DON'T MATCH. |
| | **ALSO, MISSING PAGE TWO OF THE REPORT |
| | HAVING THE LIMITATIONS ON THE PRODUCT |
| | APPLICATIONS. |
| | **NOTE: DOORS DON'T MEET THE PRESSURES |
| | CALCULATED BY THE ARCHITECT. |
| | 20-PROVIDE PRODUCT APPROVAL FOR SINGLE |
| | HUNG WINDOWS THAT MEET THE PRESSURES |
| | CALCULATED BY THE ARCHITECT. ***SOME |
| | WINDOWS DON'T MEET THOSE PRESSURES. |
| | 21-MULLION PRODUCT APPROVAL IS FOR |
| | VERTICAL APPLICATIONS. NEED PRODUCT |
| | APPROVAL FOR HORIZONTAL MULLION (EG: |
| | AT SLIDING GLASS DOORS WITH TRANSOM |
| | ABOVE. AND OTHER DESIGN. SEE PLANS). |
| | |
| | |
| | NOTE: IF YOU HAVE ANY QUESTIONS OR |
| | COMMENTS, PLEASE CONTACT JULIO |
| | GOMEZ AT (561)659-8096 X 8232. |
