| Date |
Text |
| 2002-02-01 00:00:00 | CHECKLIST: |
| | 1-NEED NOTICE OF COMMENCEMENT. |
| | 2-PAY IMPACT FEES. |
| | 3-REVISE GENERAL NOTES ON COVER SHEET. |
| | THEY REFER TO SFBC NOT SBC 1997. SEE |
| | COMMENTS ON SHEET C-1. |
| | 4-REVISE AREA CALCULATIONS. |
| | 5-SURVEY TO HAVE ORIGINAL SIGNATURE AS |
| | REQUIRED BY CHAPTER 471 FL. STATUTES. |
| | 6-PROVIDE EGRESS AT "LIBRARY". ROOM CAN |
| | BE USED FOR SLEEPING ALSO. SECTION |
| | 1005.4 SBC 1997. |
| | 7-SPECIFY ON PLANS SAFETY GLASS AS REQ'D |
| | BY SEC. 2405.2 SBC 1997. SEE PLANS. |
| | -SAFETY GLASS SHALL PASS THE TEST |
| | REQUIREMENTS OF CPSC 16-CFR,PART 1201. |
| | SEE SEC. 2405.1 SBC 1997. |
| | 8-AT LEAST ONE BATHROOM SHALL HAVE DOOR |
| | THAT PROVIDES 29" MIN. CLEAR OPENING |
| | AS REQ'D BY SECTION 11 OF FLORIDA |
| | ACCESSIBILITY CODE, 1997. |
| | 9-PROVIDE COMPLETE SPECIFICATIONS FOR |
| | CEILING INSTALLATION AT REAR AND FRONT |
| | PORCHES. SEE ASTM C926 AND ASTM C1063 |
| | FOR PROPER SPECS. SEC. 2504.2 SBC 1997 |
| | 10-REVISE SIZE OF ATTIC ACCESS ON DETAIL |
| | 2 OF A8. SEC. 2309.6 SBC 1997. |
| | 11-PROVIDE INSTALLATION DETAILS AND |
| | SPECS FOR ROPE COLUMNS AT FRONT ELEV. |
| | SECTION 104.2.2 CITY AMENDMENTS TO SBC |
| | 12-REVISE SIZE OF FASTENER FOR STRUCT'L |
| | BUCK DETAIL FOR SWING DOORS. 1 1/2" |
| | NAILS DON'T WORK FOR A 2X4 BUCK. |
| | 13-PROVIDE COMPLETE CHIMNEY DETAIL THAT |
| | MATCHES CHIMNEY SHOWN ON PLANS. |
| | SEC. 104.2.2 CITY AMENDMENTS TO SBC. |
| | 14-CLARIFY IF STORM PANELS OR IMPACT |
| | GLAZING IS GOING TO BE USED. SEE NOTE |
| | ON DWG A-2. |
| | -NEED STORM SHUTTERS PRODUCT APPROVAL |
| | AND INDICATE ON APPROVED DRAWINGS THE |
| | SPECIFIC MOUNTING CONDITIONS & ANCHOR |
| | TO BE USED ACCORDING TO THE MEAN ROOF |
| | HEIGHT, DESIGN PRESSURES, PANEL SPAN, |
| | EDGE DISTANCE AND STRUCTURE TO BE |
| | ATTACHED TO (WOOD OR CONCRETE BLOCK) |
| | 15-SPECIFY DESIGN PRESSURES CALCULATED |
| | AT SMALL GARAGE DOORS. |
| | SEC. 1606 SBC 1997. |
| | 16-CLARIFY WINDOW TYPE FOR BREAKFAST AND |
| | LIVING AREAS. ARCHITECTURAL PLANS CALL |
| | FOR FIXED WINDOWS WITH STRUCTURAL |
| | MULLIONS. PRODUCT APPROVAL INFORMATION |
| | SUBMITTED IS FOR BUTT GLAZING. |
| | REVISE PLANS AS REQUIRED. |
| | A)NOTE: IF USING BUTT GLAZING, THEN |
| | PROVIDE PRODUCT APPROVAL OR COMPLETE |
| | SITE SPECIFIC INFORMATION AND FILL |
| | ATTACHED FORM WHICH NEEDS TO BE SIGNED |
| | SEALED AND DATED BY THE MANUFACTURER'S |
| | ENGINEER & BY ARCHITECT OF RECORD. |
| | B)STOREFRONT PRODUCT APPROVAL DOESN'T |
| | HAVE LEGIBLE DRAWINGS AND CLEARLY |
| | INDICATE THE COMPONENTS TO BE USED. |
| | 17-PROVIDE PRODUCT APPROVAL FOR: |
| | A)ENTRY DOORS. SEE SIZE ON PLANS. |
| | B)FIREPLACE WITH UL LISTING. |
| | C)BBQ WITH DEEP FRYER UL LISTING. |
| | D)EXTERIOR SWING DOORS INCLUDING GARAGE. |
| | E)FRENCH DOORS WITH & WITHOUT SIDELITES. |
| | F)FRENCH DOOR WITH TRAMSOM ABOVE AS |
| | SHOWN ON EXTERIOR ELEVATIONS. |
| | 18-SEE PLANS FOR ADDITIONAL COMMENTS, |
| | INCLUDING TOSED BY THE OTHER TRADES & |
| | RETURN REVIEWED SET AFTER ORIGINAL |
| | DRAWINGS ARE CORRECTED IN ORDER TO |
| | EXPEDITE THE REVIEW PROCESS. |
