| Date |
Text |
| 2002-01-26 00:00:00 | CHECKLIST: |
| | 1-NEED RECORDED NOTICE OF COMMENCEMENT. |
| | 2-BRING COPY OF PAID IMPACT FEES RECEIPT |
| | 3-CLARIFY SHEARWALLS: |
| | A)WHY THERE ARE TWO SHEARWALL SEGMENTS |
| | SHOWN ON RIGHT ELEVATION ONLY. WHAT |
| | ABOUT SHEARWALLS ON OTHER ELEVATIONS? |
| | B)HOW ARE CORNERS AT 2ND FL. REINFORCED? |
| | 4-SPECIFY NUMBER OF RIDGE VENTS ACCORD'G |
| | TO CALCULATIONS DONE TO DETERMINE THE |
| | VENTILATION REQUIRED BY SEC. 2309.7 |
| | SBC 1997. THIS IS PART OF THE DESIGN |
| | SPECIFICATIONS. |
| | 5-SPECIFY THE DESIGN PRESSURES THAT WERE |
| | CALCULATED AT EACH EXTERIOR OPENINGS |
| | AS REQUIRED BY SEC. 1606 SBC 1997. |
| | 6-AIR CONDITIONED SQUARE FOOTAGE IS |
| | INCORRECT: |
| | A)REVISE CALCULATIONS ON SHEET 2 OF 9. |
| | B)GO TO PBC AND REVISE SQUARE FOOTAGE |
| | FOR IMPACT FEES PURPOSE AS WELL. |
| | C)CONSTRUCTION VALUE WILL BE ADJUSTED |
| | WHEN PROVIDING CORRECT SQUARE FOOTAGE. |
| | 7-SPECIFY/INDICATE ON PLANS WINDOWS TO |
| | HAVE SAFETY GLASS. SEC. 2305.2 SBC/97. |
| | 8-PROVIDE COMPLETE FRAMING DETAIL/SPECS |
| | FOR SLIDING GLASS DOORS WITH POCKET BY |
| | FAMILY AREA. SEC. 104.2.2 CITY AMENDM. |
| | 9-PROVIDE ATTIC ACCESS AT FIRST FLOOR BY |
| | BEDROOM #2 REAR ROOF. SEC. 2309.6 SBC |
| | -PROVIDE ATTIC ACCESS AT 2ND FL. ROOF. |
| | 10-PROVIDE EGRESS WINDOW FOR "GAME ROOM" |
| | SEC. 1005.4 SBC 1997. FOR SAFETY |
| | REASONS THIS ROOM IS CONSIDERED FOR |
| | SLEEPING AS WELL. |
| | 11-SPECIFY FASTENINGS FOR RAILINGS. SEC. |
| | 1608.2 SBC 1997. |
| | 12-REVISE RATIO OF STAIRS TO COMPLY WITH |
| | SEC. 1007.3 SBC 1997. SEE COMMENTS ON |
| | STAIR SECTIONS. SHEET 4 OF 9. |
| | 13-PROVIDE COMPLETE WALL SECTIONS THRU |
| | INTERIOR BEARING WALL BY FAMILY ROOM. |
| | SEE COMMENTS ON SHEET 4 OF 9. |
| | SECTION 104.2.2 CITY AMENDMENTS TO SBC |
| | SAME APPLIES TO INT. WALL SECTION AT |
| | FRONT AREA. |
| | 14-LAUNDRY ROOM UNDER STAIRS TO COMPLY |
| | WITH HEADROOM REQUIREMENTS OF SECTION |
| | 1203.2 SBC 1997. |
| | 15-ENG'R TO PROVIDE ORIGINAL SIGNATURE |
| | ON SOIL TEST REPORT AS REQUIRED BY |
| | CHAPTER 471 FLORIDA STATUTES. |
| | 16-CLARIFY REINFORCEMENT FOR ENTRY COLS. |
| | FOUNDATION PLANS AND SECTION DETAILS |
| | DON'T MATCH. |
| | 17-CLARIFY DETAIL 4 OF SHEET 8 OF 9. SEE |
| | COMMENTS ON PLANS. |
| | 18-ROOF FRAMING PLAN ON SHEET 9 OF 9 IS |
| | VERY CONFUSING BECAUSE IT'S MIXING |
| | 1ST AND SECOND FLOOR. ALSO, IT DOESN'T |
| | MATCH EXTERIOR ELEVATIONS. REVISE. |
| | 19-PROVIDE STRUCTURAL BUCK DETAIL FOR |
| | EXTERIOR SWING DOORS. SEC. 104.2.2 |
| | CITY AMENDMENTS AND SEC. 1606 SBC 1997 |
| | 20-SPECIFY CEILING INSTALLATION AT ENTRY |
| | AND REAR PORCHES. SEE ASTM C926 AND |
| | ASTM C1063 FOR PROPER SPECIFICATIONS. |
| | SECTION 2504.2 SBC 1997. |
| | 21-SEE COMMENTS ON PLANS. INCLUDING |
| | THOSE BY THE OTHER TRADES.PLEASE BRING |
| | BACK REVIEWED SET AFTER CORRECTIONS |
| | ARE DONE TO THE ORIGINAL DRAWINGS IN |
| | ORDER TO EXPEDITE THE REVIEW PROCESS. |
| | 22-REVISE ENERGY CALCULATIONS: |
| | A)OWNER INFORMATION IS WRONG. |
| | B)MAKE SURE A/C AREA MATCHES FLOOR PLANS |
| | ONCE THEY ARE REVISED. |
| | 23-PROVIDE PRODUCT APPROVAL FOR: |
| | A)HORIZONTAL ROLLING WINDOWS (DRAWINGS |
| | ARE NOT LEGIBLE). |
| | B)SINGLE HUNG WINDOWS. |
| | C)POCKET SLIDING GLASS DOORS AS SHOWN ON |
| | ARCHITECTURAL PLANS. |
| | D)SLIDING GLASS DOORS (DWGS NOT LEGIBLE) |
| | E)ENTRY DOORS (DRAWINGS NOT LEGIBLE) |
| | F)8070 GARAGE DOORS DRAWINGS (COMPLETE |
| | AND LEGIBLEDRAWINGS). |
| | G)FIXED WINDOWS. SEE SIZES ON PLANS. |
| | H)WINDOW MULLIONS. |
| | I)OVAL WINDOW. |
| | J)AWNING WINDOWS. |
| | K)ARCHED WINDOWS. |
| | |
| | 24-STORM PANELS: |
| | A)PROVIDE COMPLETE INSTALLATION SCHEDULE |
| | AS PER CITY SAMPLE ATTACHED. |
| | B)PROVIDE KEY PLAN THAT MATCHES ACTUAL |
| | ARCHITECTURAL PLANS. |
| | C)STORM SHUTTERS PRODUCT APPROVAL IS |
| | GOOD ONLY FOR ONE PERMIT. SEE NOTE |
| | ON APPROVED STORM PANEL DRAWINGS. |
| | D)CLEARLY INDICATE ON DRAWINGS MOUNTING |
| | CONDITIONS AND ANCHOR TYPE & SPACING |
| | TO BE USED ACCORDING TO THE DESIGN |
| | PRESSURES, PANEL SPAN, EDGE DISTANCE |
| | AND STRUCTURE TO BE ATTACHED TO (WOOD |
| | OR CONCRETE BLOCK). |
