Plan Review Details - Permit 21040752
Plan Review Stops For Permit 21040752
Review Stop B BUILDING (STRUCTURAL)
Rev No 3 Status P Date 2021-05-25 Cont ID  
Sent By jgomez Date 2021-05-25 Time 14:02 Rev Time 0.00
Received By jgomez Date 2021-05-25 Time 13:38 Sent To  
Notes
2021-05-25 13:42:02ROOF PRODUCT APPROVALS SUBMITTAL, SECOND BUILDING
 REVIEW COMMENTS.
 CODE: FBC 6TH EDITION (2017) AND CITY AMENDMENTS.
 SUBMITTAL #21040752
  
 1- OK.
  
 2- ROOF TILE AND ROOF TILE ADHESIVE PRODUCT APPROVALS
 SUBMITTED. CLEARLY MARK ADHESIVE PADDY SIZE AS REQUIRED
 BY CITY POLICY FOR ALL ROOFING PERMITS TO VERIFY
 COMPLIANCE WITH THE DESIGN PRESSURES OF SEC R301.2.1
 FBC-RESIDENTIAL.
 NOTE: THIS BUILDING IS LOCATED IN EXPOSURE "D". SEE
 STRUCTURAL DRAWING S-2. COORDINATE WITH DESIGNER OF
 RECORD TO AVOID CONFLICTS/DELAYS.
  
 RESPONSE:
 ROOF TILE NOA 18-0509.17 SUBMITTED WAS MARKED ON PAGE 5
 OF 9 WITH TILE BOND PADDY OF 13.9 GRAMS. THE MINIMUM
 ATTACHMENT RESISTANCE FOR THIS PADDY SIZE IS 31.3
 (FT-LBF). THIS BUILDING IS LOCATED IN EXPOSURE "D". SEE
 STRUCTURAL DRAWING S-2. USING TABLE 2A OF THE FRSA
 MANUAL (5TH EDITION REVISED) AS A REFERENCE I FOUND
 THAT FIELD TILE REQUIRES A MINIMUM OF 39.4 (FT-LBF)
 JUST FOR THE FIELD TILE. THEREFORE, SELECTED PADDY SIZE
 DOESN'T WORK. NEED TO SELECT A PADDY SIZE THAT WILL
 WORK FOR ALL ROOF ZONES, INCLUDING THE PERIMETER AND
 CORNER ROOF ZONES.
 R301.2.1 FBC-RESIDENTIAL.
  
 3- DESIGNER OF RECORD TO REVIEW/APPROVE ABOVE PRODUCT
 APPROVAL L ONCE IT IS REVISED.
 SEC. 107.3.4.1 CITY AMENDMENTS.
  
  
 PLEASE FEEL FREE TO CONTACT ME IF YOU HAVE ANY
 QUESTIONS REGARDING THESE COMMENTS,
 JULIO GOMEZ
 COMMERCIAL COMBINATION PLANS EXAMINER
 DEVELOPMENT SERVICES DEPARTMENT
 BUILDING DIVISION
 (561)805-6712
 [email protected]
  
  
  
 REMAINDER:
 THIS PROJECT WAS APPROVED WITH PROVISO. PLEASE PROVIDE
 ALL THE REQUIRED INFORMATION FOR REVIEW PRIOR TO
 INSTALLATION TO AVOID CONFLICTS/DELAYS. SEE COPY OF
 PROVISO BELOW.
  
  
 BUILDING REVIEW APPROVED WITH PROVISO:
 1-PROVIDE PRODUCT APPROVAL FOR:
 A)ROOF TILE AND SPECIFY FASTENING. IF USING SCREWS,
 SPECIFY SIZE & NUMBER.
 B)ROOF TILE ADHESIVE IF SPECIFIED ABOVE.
 C)FLAT ROOF AS SHOWN ON PLANS. AND, CLEARLY MARK WHICH
 APPROVED ASSEMBLY IS GOING TO BE INSTALLED. NOTE: RAS
 117 CALCULATIONS IF REQUIRED.
 D)ENTRY DOOR.
 E)LAUNDRY DOOR.
 F)SLIDING GLASS DOORS.
 G)FIXED WINDOWS.
 H)HORIZONTAL SLIDING WINDOWS.
 I)CASEMENT WINDOWS.
 I)OVERHEAD GARAGE DOOR.
  
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status F Date 2021-05-20 Cont ID  
Sent By jgomez Date 2021-05-20 Time 16:25 Rev Time 0.00
Received By jgomez Date 2021-05-20 Time 16:00 Sent To  
Notes
2021-05-20 16:58:53ROOF PRODUCT APPROVALS SUBMITTAL, SECOND BUILDING
 REVIEW COMMENTS.
 CODE: FBC 6TH EDITION (2017) AND CITY AMENDMENTS.
 SUBMITTAL #21040752
  
 1- OK.
  
 2- ROOF TILE AND ROOF TILE ADHESIVE PRODUCT APPROVALS
 SUBMITTED. CLEARLY MARK ADHESIVE PADDY SIZE AS REQUIRED
 BY CITY POLICY FOR ALL ROOFING PERMITS TO VERIFY
 COMPLIANCE WITH THE DESIGN PRESSURES OF SEC R301.2.1
 FBC-RESIDENTIAL.
 NOTE: THIS BUILDING IS LOCATED IN EXPOSURE "D". SEE
 STRUCTURAL DRAWING S-2. COORDINATE WITH DESIGNER OF
 RECORD TO AVOID CONFLICTS/DELAYS.
  
 RESPONSE:
 ROOF TILE NOA 18-0509.17 SUBMITTED WAS MARKED ON PAGE 5
 OF 9 WITH TILE BOND PADDY OF 13.9 GRAMS. THE MINIMUM
 ATTACHMENT RESISTANCE FOR THIS PADDY SIZE IS 31.3
 (FT-LBF). THIS BUILDING IS LOCATED IN EXPOSURE "D". SEE
 STRUCTURAL DRAWING S-2. USING TABLE 2A OF THE FRSA
 MANUAL (5TH EDITION REVISED) AS A REFERENCE I FOUND
 THAT FIELD TILE REQUIRES A MINIMUM OF 39.4 (FT-LBF)
 JUST FOR THE FIELD TILE. THEREFORE, SELECTED PADDY SIZE
 DOESN'T WORK. NEED TO SELECT A PADDY SIZE THAT WILL
 WORK FOR ALL ROOF ZONES, INCLUDING THE PERIMETER AND
 CORNER ROOF ZONES.
 R301.2.1 FBC-RESIDENTIAL.
  
 3- DESIGNER OF RECORD TO REVIEW/APPROVE ABOVE PRODUCT
 APPROVAL L ONCE IT IS REVISED.
 SEC. 107.3.4.1 CITY AMENDMENTS.
  
  
 PLEASE FEEL FREE TO CONTACT ME IF YOU HAVE ANY
 QUESTIONS REGARDING THESE COMMENTS,
 JULIO GOMEZ
 COMMERCIAL COMBINATION PLANS EXAMINER
 DEVELOPMENT SERVICES DEPARTMENT
 BUILDING DIVISION
 (561)805-6712
 [email protected]
  
  
  
 REMAINDER:
 THIS PROJECT WAS APPROVED WITH PROVISO. PLEASE PROVIDE
 ALL THE REQUIRED INFORMATION FOR REVIEW PRIOR TO
 INSTALLATION TO AVOID CONFLICTS/DELAYS. SEE COPY OF
 PROVISO BELOW.
  
  
 BUILDING REVIEW APPROVED WITH PROVISO:
 1-PROVIDE PRODUCT APPROVAL FOR:
 A)ROOF TILE AND SPECIFY FASTENING. IF USING SCREWS,
 SPECIFY SIZE & NUMBER.
 B)ROOF TILE ADHESIVE IF SPECIFIED ABOVE.
 C)FLAT ROOF AS SHOWN ON PLANS. AND, CLEARLY MARK WHICH
 APPROVED ASSEMBLY IS GOING TO BE INSTALLED. NOTE: RAS
 117 CALCULATIONS IF REQUIRED.
 D)ENTRY DOOR.
 E)LAUNDRY DOOR.
 F)SLIDING GLASS DOORS.
 G)FIXED WINDOWS.
 H)HORIZONTAL SLIDING WINDOWS.
 I)CASEMENT WINDOWS.
 I)OVERHEAD GARAGE DOOR.
  
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2021-05-13 Cont ID  
Sent By jgomez Date 2021-05-13 Time 16:16 Rev Time 0.00
Received By jgomez Date 2021-05-13 Time 15:12 Sent To  
Notes
2021-05-13 16:18:40ROOF PRODUCT APPROVALS SUBMITTAL, BUILDING REVIEW
 COMMENTS.
 CODE: FBC 6TH EDITION (2017) AND CITY AMENDMENTS.
 SUBMITTAL #21040752
  
 1- FLAT ROOF FLORIDA PRODUCT APPROVAL FL2533-R24:
 THIS BUILDING IS LOCATED IN EXPOSURE "D". SEE
 STRUCTURAL DRAWING S-2. THE DESIGN PRESSURE OF SELECTED
 ASSEMBLY W-65 IS 105 PSF. THE DESIGN PRESSURE FOR
 COMPONENTS AND CLADDING ON ROOF ZONE #3 IS HIGHER THAN
 105PSF. NEED TO PROVIDE SIGNED AND SEALED RAS 1117
 CALCULATIONS. SEE NOTE #9 ON PAGE 3 OF 74 OF THIS
 PRODUCT APPROVAL OR SELECT ANOTHER ASSEMBLY THAT MEETS
 THE DESIGN PRESSURES FOR ALL ROOF ZONES. COORDINATE
 WITH DESIGNER OF RECORD TO AVOID CONFLICTS/DELAYS.
  
 2- ROOF TILE AND ROOF TILE ADHESIVE PRODUCT APPROVALS
 SUBMITTED. CLEARLY MARK ADHESIVE PADDY SIZE AS REQUIRED
 BY CITY POLICY FOR ALL ROOFING PERMITS TO VERIFY
 COMPLIANCE WITH THE DESIGN PRESSURES OF SEC R301.2.1
 FBC-RESIDENTIAL.
 NOTE: THIS BUILDING IS LOCATED IN EXPOSURE "D". SEE
 STRUCTURAL DRAWING S-2. COORDINATE WITH DESIGNER OF
 RECORD TO AVOID CONFLICTS/DELAYS.
  
 3- DESIGNER OF RECORD TO REVIEW AND APPROVE IN WRITING
 (NOT SIGNING AND SEALING) ALL PRODUCT APPROVALS AS
 REQUIRED BY SEC. 107.3.4.1 CITY AMENDMENTS.
  
  
 PLEASE FEEL FREE TO CONTACT ME IF YOU HAVE ANY
 QUESTIONS REGARDING THESE COMMENTS,
 JULIO GOMEZ
 COMMERCIAL COMBINATION PLANS EXAMINER
 DEVELOPMENT SERVICES DEPARTMENT
 BUILDING DIVISION
 (561)805-6712
 [email protected]
  
  
  
 REMAINDER:
 THIS PROJECT WAS APPROVED WITH PROVISO. PLEASE PROVIDE
 ALL THE REQUIRED INFORMATION FOR REVIEW PRIOR TO
 INSTALLATION TO AVOID CONFLICTS/DELAYS. SEE COPY OF
 PROVISO BELOW.
  
  
 BUILDING REVIEW APPROVED WITH PROVISO:
 1-PROVIDE PRODUCT APPROVAL FOR:
 A)ROOF TILE AND SPECIFY FASTENING. IF USING SCREWS,
 SPECIFY SIZE & NUMBER.
 B)ROOF TILE ADHESIVE IF SPECIFIED ABOVE.
 C)FLAT ROOF AS SHOWN ON PLANS. AND, CLEARLY MARK WHICH
 APPROVED ASSEMBLY IS GOING TO BE INSTALLED. NOTE: RAS
 117 CALCULATIONS IF REQUIRED.
 D)ENTRY DOOR.
 E)LAUNDRY DOOR.
 F)SLIDING GLASS DOORS.
 G)FIXED WINDOWS.
 H)HORIZONTAL SLIDING WINDOWS.
 I)CASEMENT WINDOWS.
 I)OVERHEAD GARAGE DOOR.
  
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2021-05-25 Cont ID  
Sent By jgomez Date 2021-05-25 Time 14:02 Rev Time 0.00
Received By jgomez Date 2021-05-25 Time 13:38 Sent To I
Notes
***NONE***
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2021-05-20 Cont ID  
Sent By jgomez Date 2021-05-20 Time 16:58 Rev Time 0.00
Received By jgomez Date 2021-05-20 Time 15:59 Sent To I
Notes
2021-05-20 15:59:50EMAIL FROM ARCHITECT. JG
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date 2021-05-13 Cont ID  
Sent By jgomez Date 2021-05-13 Time 16:18 Rev Time 0.00
Received By jgomez Date 2021-04-15 Time 14:14 Sent To I
Notes
***NONE***
Review Stop SIGNATURE ELECTRONIC SIGNATURE SHEET
Rev No 1 Status N Date 2021-05-13 Cont ID  
Sent By jgomez Date 2021-05-13 Time 16:18 Rev Time 0.00
Received By jgomez Date 2021-05-13 Time 16:18 Sent To  
Notes
***NONE***


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved