Plan Review Details - Permit 21010017
Plan Review Stops For Permit 21010017
Review Stop B BUILDING (STRUCTURAL)
Rev No 3 Status P Date 2021-01-27 Cont ID  
Sent By mcdouga Date 2021-01-27 Time 16:51 Rev Time 0.00
Received By rmcdouga Date 2021-01-27 Time 16:51 Sent To  
Notes
***NONE***
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status F Date 2021-01-21 Cont ID  
Sent By rmcdouga Date 2021-01-21 Time 09:07 Rev Time 0.00
Received By rmcdouga Date 2021-01-21 Time 09:07 Sent To  
Notes
2021-01-21 09:14:42PLAN
 REVIEW COMMENTS
  
 2ND REVIEW: FBC SEVENTH EDITION (2020)
 ROBERT MCDOUGAL, CBO
 COMMERCIAL COMBINATION PLANS EXAMINER
 (561) 805-6714
 [email protected]
  
 DENIED BY BUILDING
 PLEASE ADDRESS THE ITEMS NOTED BELOW:
  
 1) THE PRODUCT APPROVALS DO NOT HAVE A SHOP REVIEW
 APPROVAL STAMP FROM THE ENGINEER, HOWEVER, THE ENGINEER
 SIGNED AND SEALED THE RESPONSE LETTER WHICH LISTS THE
 PRODUCT NOA NOS. FOR THE SLIDING GLASS DOORS AND THE
 THE SINGLE HUNG WINDOW. THIS WOULD BE SUFFICIENT EXCEPT
 THAT THE NOA NUMBER IN THE LETTER (NOA NO. 19-0230.05)
 DOES NOT MATCH THE ONE THAT WAS SUBMITTED(NOA NO.
 19-0130.05). PLEASE REVISE THE LETTER OR SUBMIT THE
 CORRESPONDING PRODUCT APPROVAL. FBC 107.2.1
  
 2) PROVIDE CLARIFICATION FOR THE BUTT WELD FOR THE
 CORNER COLUMN REPAIR ON PAGE 140 OF THE DRAWINGS. THE
 WELD IS SPECIFIED AS 1/16" ON 1/4" MATERIAL, SHOULDN'T
 THE MINIMUM WELD BE AT LEAST 3/16"? FBC 107.2.1
  
  
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2021-01-07 Cont ID  
Sent By rmcdouga Date 2021-01-07 Time 08:36 Rev Time 0.00
Received By rmcdouga Date 2021-01-06 Time 15:29 Sent To  
Notes
2021-01-07 08:36:03PLAN
 REVIEW COMMENTS
  
 1ST REVIEW: FBC SEVENTH EDITION (2020)
 ROBERT MCDOUGAL, CBO
 COMMERCIAL COMBINATION PLANS EXAMINER
 (561) 805-6714
 [email protected]
  
 DENIED BY BUILDING
 PLEASE ADDRESS THE ITEMS NOTED BELOW:
  
 1) SUBMIT REQUIRED COMPONENT AND CLADDING DESIGN
 PRESSURES FOR THE OPENINGS THAT HAVE BEEN PREPARED BY A
 FLORIDA LICENSED ENGINEER. THE DOCUMENTS ARE REQUIRED
 TO BE DIGITALLY SIGNED BY THE ENGINEER IF SUBMITTED
 ELECTRONICALLY AND THE ENGINEER'S ORIGINAL HANDWRITTEN
 SIGNATURE IF PAPER DOCUMENTS ARE SUBMITTED. FS 471 &
 FAC 61G15
  
 2) ELEVATIONS OF THE BUILDING SHOWING THE WALL ZONES
 AND REQUIRED PRESSURES, A WINDOW AND DOOR SCHEDULE WITH
 THE OPENING SIZES, REQUIRED PRESSURES, PRODUCT APPROVAL
 NUMBER AND DESIGN PRESSURE FROM THE PRODUCT APPROVAL IS
 REQUIRED. FBC 107.2.1.2
  
 3) HI-LIGHT OR CIRCLE THE SPECIFIC DETAILS AND DESIGN
 PRESSURES THAT APPLY TO THIS PROJECT IN THE WINDOW AND
 DOOR PRODUCT APPROVALS. FBC 107.2.1
  
 4) THE PRODUCT APPROVALS ARE REQUIRED TO BE REVIEWED
 AND APPROVED BY THE DESIGNER OF RECORD FOR THE PROJECT.
 FBC 107.3.4
  
 5) PURSUANT TO FBC 107.1, AND FS 481.229 (1) (C), AS
 THIS THIS DESIGN EXCEEDS $25,000.00 IN VALUE, THE
 DESIGN MUST BE PREPARED BY A PROFESSIONAL LICENSED
 PURSUANT TO FS 481. SEE BELOW:
 FBC107.1 GENERAL. SUBMITTAL DOCUMENTS CONSISTING OF
 CONSTRUCTION DOCUMENTS, STATEMENT OF SPECIAL
 INSPECTIONS, GEOTECHNICAL REPORT AND OTHER DATA SHALL
 BE SUBMITTED IN TWO OR MORE SETS WITH EACH PERMIT
 APPLICATION. THE CONSTRUCTION DOCUMENTS SHALL BE
 PREPARED BY A REGISTERED DESIGN PROFESSIONAL WHERE
 REQUIRED BY CHAPTER 471, FLORIDA STATUTES & 61G15
 FLORIDA ADMINISTRATIVE CODE OR CHAPTER 481, FLORIDA
 STATUTES & 61G1 FLORIDA ADMINISTRATIVE CODE. WHERE
 SPECIAL CONDITIONS EXIST, THE BUILDING OFFICIAL IS
 AUTHORIZED TO REQUIRE ADDITIONAL CONSTRUCTION DOCUMENTS
 TO BE PREPARED BY A
 REGISTERED DESIGN PROFESSIONAL. ELECTRONIC MEDIA
 DOCUMENTS SHALL BE SUBMITTED WHEN REQUIRED BY THE
 BUILDING OFFICIAL, AND MAY REQUIRE ONLY ONE SET OF
 SUBMITTALS.
  
 6) THE REPAIR DRAWINGS AND DETAILS ARE REQUIRED TO BE
 SIGNED AND SEALED BY THE DESIGNER OF RECORD AND HAVE A
 TITLE BLOCK.
 61G15-23.001 SIGNATURE, DATE AND SEAL SHALL BE AFFIXED.
 (1) A PROFESSIONAL ENGINEER SHALL SIGN, DATE AND SEAL:
 (A) ALL FINAL PLANS, PRINTS, SPECIFICATIONS, REPORTS,
 OR OTHER DOCUMENTS PREPARED OR ISSUED BY THE LICENSEE
 AND BEING FILED FOR PUBLIC RECORD;
 (B) ALL FINAL DOCUMENTS PROVIDED TO THE OWNER OR THE
 OWNER'S REPRESENTATIVE.
 (2) ADDITIONAL FINAL AND NON-FINAL DOCUMENTS.
 (A) A PROFESSIONAL ENGINEER MAY SIGN, DATE AND SEAL
 DOCUMENTS REQUIRED BY ANY PUBLIC ENTITY OR ANY
 PROVISION OF CONTRACT WHICH REQUIRES THE SIGNING,
 DATING AND SEALING OF ADDITIONAL ORIGINAL DOCUMENTS.
 (B) A PROFESSIONAL ENGINEER SHALL NOT SIGN, DATE AND
 SEAL ANY DOCUMENTS WHICH ARE NOT FINAL DOCUMENTS UNLESS
 THE PROFESSIONAL ENGINEER STATES ANY LIMITATIONS ON THE
 USE OF THOSE DOCUMENTS ON THE FACE OF THOSE DOCUMENTS
 BY USING TERMS SUCH AS ?PRELIMINARY,? ?FOR REVIEW
 ONLY,? ?NOT FOR CONSTRUCTION,? OR ANY OTHER SUITABLE
 STATEMENT WHICH DENOTES THAT THE DOCUMENTS ARE FOR
 LIMITED USE, ARE NOT FINAL AND ARE NOT INTENDED FOR
 PERMIT, CONSTRUCTION, OR BIDDING PURPOSES.
 (3) A PROFESSIONAL ENGINEER MAY ONLY SIGN, DATE AND
 SEAL ENGINEERING PLANS, PRINTS, SPECIFICATIONS, REPORTS
 OR OTHER DOCUMENTS IF THAT PROFESSIONAL ENGINEER WAS IN
 RESPONSIBLE CHARGE, AS THAT TERM IS DEFINED IN
 SUBSECTION 61G15-18.011(1), F.A.C., OF THE PREPARATION
 AND PRODUCTION OF THE ENGINEERING DOCUMENT AND THE
 PROFESSIONAL ENGINEER HAS THE EXPERTISE IN THE
 ENGINEERING DISCIPLINE USED IN PRODUCING THE
 ENGINEERING DOCUMENT(S) IN QUESTION. PROFESSIONAL
 ENGINEERS WORKING FOR LOCAL, STATE OR FEDERAL
 GOVERNMENT AGENCIES SHALL LEGIBLY INDICATE THEIR NAME
 AND LICENSE NUMBER AND SHALL INDICATE THE NAME AND
 ADDRESS OF THE AGENCY ON ALL DOCUMENTS THAT ARE
 REQUIRED TO BE SIGNED, DATED AND SEALED.
 (4) ADDITIONAL REQUIREMENTS FOR PLANS OR PRINTS,
 ENGINEERING SPECIFICATIONS AND CALCULATIONS, AND
 ENGINEERING REPORTS OR OTHER DOCUMENTS. WHEN AN
 ENGINEER SIGNS, DATES AND SEALS ANY OF THE FOLLOWING
 TYPES OF DOCUMENTS PLANS OR PRINTS UNDER THE PROVISIONS
 OF SECTION 471.025, F.S., AND SUBSECTION (1) OF THIS
 RULE, THE FOLLOWING ADDITIONAL INFORMATION MUST BE
 INCLUDED:
 (A) PLANS AND PRINTS. EVERY SHEET WITHIN THE PLANS AND
 PRINTS MUST BE SIGNED, DATED AND SEALED BY THE
 PROFESSIONAL ENGINEER IN RESPONSIBLE CHARGE.
 1. A TITLE BLOCK SHALL BE USED ON EACH SHEET OF PLANS
 OR PRINTS AND SHALL CONTAIN THE PRINTED NAME, ADDRESS,
 AND LICENSE NUMBER OF THE ENGINEER WHO HAS SIGNED,
 DATED AND SEALED THE PLANS OR PRINTS.
 2. IF THE ENGINEER SIGNING, DATING AND SEALING
 ENGINEERING PLANS OR PRINTS IS PRACTICING THROUGH A
 DULY AUTHORIZED QUALIFIED ENGINEERING BUSINESS
 ORGANIZATION; THE TITLE BLOCK SHALL CONTAIN THE PRINTED
 NAME AND ADDRESS OF THE QUALIFIED ENGINEERING BUSINESS
 ORGANIZATION.
 (B) ENGINEERING SPECIFICATIONS AND CALCULATIONS. AN
 INDEX SHEET SHALL BE USED AND SHALL BE SIGNED, DATED
 AND SEALED BY EACH PROFESSIONAL ENGINEER WHO IS IN
 RESPONSIBLE CHARGE OF ANY PORTION OF THE ENGINEERING
 SPECIFICATIONS OR CALCULATIONS.
 1. THE INDEX SHEET MUST BE SIGNED, DATED AND SEALED BY
 THOSE PROFESSIONAL ENGINEERS IN RESPONSIBLE CHARGE OF
 THE PRODUCTION AND PREPARATION OF EACH SECTION OF THE
 ENGINEERING SPECIFICATIONS OR CALCULATIONS, WITH
 SUFFICIENT INFORMATION ON THE INDEX SHEET SO THAT THE
 USER WILL BE AWARE OF EACH PORTION OF THE
 SPECIFICATIONS OR CALCULATIONS FOR WHICH EACH
 PROFESSIONAL ENGINEER IS RESPONSIBLE.
 2. THE INDEX SHEET SHALL INCLUDE AT A MINIMUM:
 A. THE PRINTED NAME, ADDRESS AND LICENSE NUMBER OF EACH
 ENGINEER IN RESPONSIBLE CHARGE OF THE PRODUCTION OF ANY
 PORTION OF THE CALCULATIONS OR SPECIFICATIONS.
 B. IF THE ENGINEER SIGNING, DATING AND SEALING
 CALCULATIONS OR SPECIFICATIONS IS PRACTICING THROUGH A
 DULY QUALIFIED ENGINEERING BUSINESS ORGANIZATION; THE
 PRINTED NAME AND ADDRESS OF THE QUALIFIED ENGINEERING
 BUSINESS ORGANIZATION.
 C. IDENTIFICATION OF THE PROJECT, BY ADDRESS OR BY LOT
 NUMBER, BLOCK NUMBER, SECTION OR SUBDIVISION AND CITY
 OR COUNTY.
 D. IDENTIFICATION OF THE APPLICABLE BUILDING CODE AND
 CHAPTER(S) AND FLORIDA FIRE PREVENTION CODE, WHEN
 APPLICABLE, THAT THE DESIGN IS INTENDED TO MEET.
 E. IDENTIFICATION OF ANY COMPUTER PROGRAM USED FOR
 ENGINEERING THE SPECIFICATIONS OR CALCULATIONS.
 (C) ENGINEERING REPORTS OR OTHER DOCUMENTS.
 1. A SIGNATURE PAGE OR COVER LETTER SHALL BE USED AND
 SHALL BE SIGNED, DATED AND SEALED BY EACH PROFESSIONAL
 ENGINEER WHO IS IN RESPONSIBLE CHARGE OF ANY PORTION OF
 THE REPORT WITH SUFFICIENT INFORMATION PROVIDED SO THAT
 THE USER WILL BE AWARE OF EACH PORTION FOR WHICH EACH
 PROFESSIONAL ENGINEER IS RESPONSIBLE.
 2. IF THE ENGINEER SIGNING, DATING AND SEALING AN
 ENGINEERING REPORT OR OTHER DOCUMENT IS PRACTICING
 THROUGH A DULY QUALIFIED ENGINEERING BUSINESS
 ORGANIZATION, THE PRINTED NAME AND ADDRESS OF THE
 QUALIFIED ENGINEERING BUSINESS ORGANIZATION.
 (D) THE DATE THAT THE SIGNATURE AND SEAL IS AFFIXED AS
 PROVIDED HEREIN SHALL BE ENTERED ON SAID PLANS, PRINTS,
 SPECIFICATION, REPORTS OR OTHER DOCUMENTS IMMEDIATELY
 ADJACENT TO THE SIGNATURE OF THE PROFESSIONAL ENGINEER.
  
 7) WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A
 RESPONSE LETTER ADDRESSING EACH ITEM ALONG WITH THE
 CITY RE-SUBMITTAL FORM.
  
  
  
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2021-01-27 Cont ID  
Sent By rmcdouga Date 2021-01-27 Time 16:51 Rev Time 0.00
Received By rmcdouga Date 2021-01-27 Time 11:02 Sent To  
Notes
***NONE***
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2021-01-21 Cont ID  
Sent By rmcdouga Date 2021-01-21 Time 09:07 Rev Time 0.00
Received By rmcdouga Date 2021-01-20 Time 11:42 Sent To  
Notes
***NONE***
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date 2021-01-07 Cont ID  
Sent By rmcdouga Date 2021-01-07 Time 08:36 Rev Time 0.00
Received By rmcdouga Date 2021-01-05 Time 22:06 Sent To  
Notes
***NONE***
Review Stop SIGNATURE ELECTRONIC SIGNATURE SHEET
Rev No 3 Status P Date 2021-01-27 Cont ID  
Sent By pvalenti Date 2021-01-27 Time 13:29 Rev Time 0.00
Received By pvalenti Date 2021-01-27 Time 13:29 Sent To  
Notes
***NONE***
Review Stop SIGNATURE ELECTRONIC SIGNATURE SHEET
Rev No 2 Status P Date 2021-01-20 Cont ID  
Sent By pvalenti Date 2021-01-20 Time 06:36 Rev Time 0.00
Received By pvalenti Date 2021-01-20 Time 06:36 Sent To  
Notes
2021-01-20 06:37:09PETER E VALENTI
 BUILDING PLANS EXAMINER
 [email protected]
 561-805-6673
  
 FBC = FLORIDA BUILDING CODE, 6TH EDITION (2017)
 FBC B = FBC BUILDING
 FBC EB = FBC EXISTING BUILDING
 FBC A = FBC ACCESSIBILITY
 FBC EC = FBC ENERGY CONSERVATION
 FBC R = FBC RESIDENTIAL
 FBC M = FBC MECHANICAL
 FBC FG = FBC FUEL GAS
  
 SIGNATURE REVIEW APPROVED BY SIGNED/SEALED ORIGINAL
 PAPER SUBMITTALS.
Review Stop SIGNATURE ELECTRONIC SIGNATURE SHEET
Rev No 1 Status F Date 2021-01-06 Cont ID  
Sent By rmcdouga Date 2021-01-06 Time 16:37 Rev Time 0.00
Received By rmcdouga Date 2021-01-06 Time 15:29 Sent To  
Notes
2021-01-06 16:44:38ELECTRONICALLY SUBMITTED DRAWINGS ARE REQUIRED TO HAVE
 THE ENGINEER'S DIGITAL SIGNATURE ON THEM. YOU ALSO HAVE
 THE OPTION TO SUBMIT THE SIGNED AND SEALED PAPER
 VERSION OF DRAWINGS. AFTER THE ELECTRONIC PLANS HAVE
 BEEN APPROVED, YOU CAN SUBMIT THE CORRESPONDING PAPER
 DRAWINGS AT THE BUILDING DEPARTMENT TO BE VERIFIED. THE
 ENGINEER'S ORIGINAL HANDWRITTEN SIGNATURE AND SEAL IS
 REQUIRED TO BE ON THE DRAWINGS. NO PHOTOCOPY OR OTHER
 FACSIMILES OF THE SIGNATURE ARE ACCEPTABLE. FS 471 &
 61G15
Review Stop THRESHOLD THRESHOLD INSPECTOR DOCUMENTS
Rev No 1 Status P Date 2021-01-06 Cont ID  
Sent By rmcdouga Date 2021-01-06 Time 15:30 Rev Time 0.00
Received By rmcdouga Date 2021-01-06 Time 15:29 Sent To  
Notes
2021-01-06 16:12:12TIMOTHY S. MARSHALL - PE 41992, SI 1022
 A.T. DESIGNS INC. CA 5554
 BOB ROBERT TILLEY - BN 4395
 MICHAEL J. BIANCHINI - CGC 031560
 CAROUSAL DEVELOPEMENT & RESTORATION INC.


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved