| 2020-10-15 14:29:47 | WEST PALM BEACH DEVELOPMENT SERVICES-CONSTRUCTION |
| | SERVICES/ BUILDING DIVISION |
| | 2017 FBC- BUILDING PLAN REVIEW |
| | W. P. B. PERMIT: 20091255 |
| | ADD: 1801 S FLAGLER DR. # 1210 |
| | CONT: AT YOUR SERVICE WINDOWS & DOORS |
| | TEL: 561-846-2378 |
| | E-MAIL: JOHN@ AYSWINDOWS.COM |
| | |
| | 2017 FLORIDA BUILDING CODE W 2017 WEST PALM BEACH |
| | AMENDMENTS TO THE FLORIDA BUILDING CODE, CHAPTER 1, |
| | ADMINISTRATION |
| | |
| | 2017 EXISTING BUILDING CODE. 801.3 COMPLIANCE. ALL NEW |
| | CONSTRUCTION ELEMENTS, COMPONENTS, SYSTEMS, AND SPACES |
| | SHALL COMPLY WITH THE REQUIREMENTS OF THE FLORIDA |
| | BUILDING CODE, BUILDING. |
| | |
| | 2ND REVIEW |
| | DATE: MON. OCT. 12TH/ 2020 |
| | ACTION: DENIED |
| | |
| | 1) SEMI COMPLIED, CONTRACTOR SIGNED THEIR NAME AND |
| | LICENSE NUMBER BUT DIDNOT PRINT THEIR NAME ON THE FLOOR |
| | PLAN. THE CONTRACTOR FAILED TO SIGN, NOR PRINT THEIR |
| | NAME AND LICENSE NUMBER ON THE PRODUCT APPROVAL REVIEW |
| | FORM, THIS DOCUMENT IS ALSO PART OF THE CONTRACTORS |
| | DESIGN AS FAR AS TYPES OF GLAZING UNITS, SIZE AND |
| | ASSOCIATED PRESSURES. |
| | 1ST ROUND OF COMMENTS. PLEASE NOTE THE SUBMITTED FLOOR |
| | PLAN NEEDS TO HAVE THE QUALIFIER/ CERTIFICATE HOLDER |
| | PRINT THEIR NAME, SIGN THEIR NAME AND LICENSE NUMBER ON |
| | ALL OF THEIR DRAWINGS. CERTIFICATION BY CONTRACTOR. |
| | 107.3.4.3 CERTIFICATION BY CONTRACTOR. PLEASE NOTE THE |
| | EXCEPTION TO ENGINEERED PLANS UNDER 471.003(H) |
| | ELECTRICAL/ PLUMBING/ MECHANICAL, 481.229(1)(C) |
| | (BUILDING) REQUIRES THE CONTRACTOR FOR THAT TRADE THAT |
| | WILL BE LICENSED IN THAT TRADE, WILL ALSO BE THE |
| | CONTRACTOR THAT DESIGNS THE SYSTEM UNDER THAT TRADE. |
| | THE CONTRACTOR (QUALIFIER) THAT CREATED / DRAWN THE SET |
| | OF PLANS WILL NEED TO IDENTIFY THEMSELVES AS THE AUTHOR |
| | OF THE PLANS. PLEASE PRINT YOUR NAME, SIGN YOUR NAME |
| | AND LICENSE NUMBER FOR THE TRADE YOU ARE LICENSED IN |
| | AND PLANS DRAWN. |
| | FOR EACH TRADE THE CONTRACTOR RESPONSIBLE FOR THE |
| | DESIGN UNDER THE TRADE LICENSED IN MUST PRINT THEIR |
| | NAME, SIGN THEIR NAME AND LICENSE NUMBER, NOTE THESE |
| | PLANS APPEAR TO BE DRAWN BY ONE INDUVIAL, THEY WOULD |
| | HAVE TO BE LICENSED AS A BUILDING, ELECTRICAL AND |
| | PLUMBING CONTRACTOR TO SUBMIT ALL THESE TRADES UNDER |
| | ONE SHEET. |
| | |
| | 2) COMPLIED. THE SUBMITTED FLOOR PLAN DOES NOT SHOW THE |
| | LOCATION OF THE UNIT COMPARED TO THE OVERALL BUILDING |
| | FLOOR PLAN, CANNOT DETERMINE IF THE UNIT IS IN WALL |
| | ZONE 4 OR WALL ZONE 5. PRESSURES WILL DIFFER GREATLY. |
| | 107.2.1.2 ADDITIONAL INFORMATION IS REQUIRED. 2017 |
| | FBC-B 1603.1.4 WIND DESIGN DATA. |
| | |
| | 3) 2ND REVIEW. THE SINGLE HUNG WINDOWS AND MULLIONS |
| | WERE NOT IDENTIFIED, THE PLAN REVIEWER CIRCLED OPENING |
| | SIZES AND ASSOCIATED PRESURES ALL GLAZING TYPES WORKED. |
| | THE SLIDING GLASS DOORS NOTHING WAS IDENTIFIED. WHEN |
| | REVIEWING THESE OPENINGS USING THE INFROMATION FROM THE |
| | PRODUCT APPROVAL FORM AND THE DESIGN PRRESSURE CHART |
| | THE PRODUCT APPROVAL FL. 18321-R2 PAGE 3/23 INDICATES |
| | REGAURDLESS OF PANEL SIZE (UNKNOWN CONTRACTOR GAVE THE |
| | OVERALL SIZE OF THE OPENING, SLIDING GLASS DOORS ALWAYS |
| | USE PANEL SIZE BECAUSE OF THE INTERLOCK BETWEEN |
| | PANELS/ DOORS ACTS AS A MULLION) THE HEIGHT IS KNOWN 96 |
| | INCHES AND FOR BOTH THE STANDARD ASTRICAL AND HEAVY |
| | DUTY LIMIT THE PRESSURE TO 60.0 PSF. THE SUBMITTED |
| | PRODUCT APPROVAL FORM 1 SHOWED THE PRODUCT |
| | REQUIRED-62.8 PSF BUT THE APPROVAL IS GOOD FOR ONLY =/- |
| | 60.00 PSF. THE 2ND PRODUCT APPROVAL REVIEW FORM THE NOA |
| | DESIN PRESSURE VALUES WERE INCREASED TO +/- 80 PSF |
| | WHICH ARE HIGHER THAN THE REQUIRD DESIGN PRESSURES, BUT |
| | THE PRODUCT APPROVAL SUBMITTED ATECHNICAL SHEETS STILL |
| | SHOW =/- 60.00PSF.PLEASE REVIEW WITHIN THE SAME PRODUCT |
| | APPROVAL SYSTEM 18321.1 SERIES 600 KM IS GOOD FOR |
| | +90/-110 PSF. IF THE CONTRACTOR WISHES TO INSTALL THIS |
| | UNIT THE TESTING REPORTS (EVALUATION) AND INSTALLATION |
| | INSTRUCTIONS WOULD NEED TO BE UPLOADED AND IDENTIFY |
| | OPENING SIZE, PRESSURES, TPYE OF ASTRICAL, POSSIBLE |
| | GLAZING TYPE!!! |
| | |
| | 1ST ROUND OF COMMENTS. NONE OF THE SUBMITTED PRODUCT |
| | APPROVALS IDENTIFY THE TYPE OF GLASS, SIZE OF GLAZING, |
| | MULLIONS AND ASSOCIATED PRESSURES. |
| | IDENTIFY GLAZING/ MULLIONS. PLEASE IDENTIFY ON THE |
| | PRODUCT APPROVAL BEFORE SUBMITTING TO DESIGNER OF |
| | RECORD AND BEFORE SUBMISSION TO THE BUILDING |
| | DEPARTMENT. FOR ALL PRODUCTS WITH GLAZING, PLEASE |
| | IDENTIFY THE OPENING WIDTH & HEIGHT, TYPE OF GLAZING, |
| | MULLION SIZE, LENGTH IF UNREINFORCED OR REINFORCED |
| | INFORMATION IF REQUIRED, ATTACHMENTS AND ASSOCIATE |
| | PRESSURES FOR EACH OPENING SIZE. 2017 FBC-B 1405.13.1 |
| | INSTALLATION. WINDOWS AND DOORS SHALL BE INSTALLED IN |
| | ACCORDANCE WITH APPROVED MANUFACTURER?S INSTRUCTIONS. |
| | FASTENER SIZE AND SPACING SHALL BE PROVIDED IN SUCH |
| | INSTRUCTIONS AND SHALL BE CALCULATED BASED ON MAXIMUM |
| | LOADS AND SPACING USED IN THE TESTS. |
| | |
| | 4) A TRANSMITTAL LETTER LISTING THE ORIGINAL REVIEW |
| | COMMENT NUMBER, WITH A DESCRIPTION OF THE REVISION |
| | MADE, IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE |
| | THE CHANGES CAN BE FOUND WILL HELP TO EXPEDITE YOUR |
| | PERMIT. THANK YOU FOR YOUR ANTICIPATED COOPERATION. |
| | |
| | PLEASE NOTE WITH THE LACK OF INFORMATION FOR THIS |
| | REVIEW, SUBSEQUENT REMARKS MAYBE MADE IN THE NEXT |
| | REVIEW CYCLE. |
| | |
| | PLEASE NOTE WE ARE WORKING FROM HOME BECAUSE OF COVID |
| | 19 |
| | IF YOU WOULD LIKE TO CONTACT ME, MY CELL NUMBER IS |
| | 561-718-9724. |
| | |
| | JAMES A. WITMER BN, PX, SFP, CBO |
| | SENIOR COMMERCIAL COMBINATION PLANS EXAMINER |
| | BUILDING DIVISION / DEVELOPMENT SERVICES DEPARTMENT |
| | 401 CLEMATIS ST. WEST PALM BEACH. FL 33402 |
| | TEL: 561-805-6717 |
| | FAX: 561-805-6676 |
| | E-MAIL: [email protected] |
| | |
| | |
