City of West Palm Beach eGovPlus

Plan Review Details - Permit 18081583

Plan Review Stops For Permit 18081583

Review Stop	AD			ADDRESSING
Rev No	2	Status	P	Date	2020-01-07			Cont ID
Sent By	cpuell			Date	2020-01-07	Time	13:04	Rev Time	0.00
Received By	cpuell			Date	2020-01-07	Time	13:04	Sent To

Notes

2020-01-07 13:04:46

ADDRESS SHOULD BE 317 DATURA ST

Review Stop	AD			ADDRESSING
Rev No	1	Status	F	Date	2019-03-05			Cont ID
Sent By	dbattles			Date	2019-03-05	Time	08:38	Rev Time	0.00
Received By	dbattles			Date	2019-03-05	Time	08:38	Sent To

Notes

2019-03-05 08:39:45	HOW WILL THIS BE ADDRESSED?
	PLEASE CALL MICHAEL ORIO BY PHONE AT 561-494-1080, OR
	BY E-MAIL [email protected]

	DYLAN BATTLES
	BUILDING PLANS EXAMINER PX4191
	[email protected]
	561-805-6718

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2018-11-14			Cont ID
Sent By	dbattles			Date	2018-11-14	Time	08:53	Rev Time	0.00
Received By	dbattles			Date	2018-11-08	Time	11:36	Sent To

Notes

2018-11-14 08:54:08	**CORRECTIONS**
	W.P.B. PERMIT: 18081583
	REVIEWED: NOVEMBER 14, 2018

	DYLAN BATTLES
	BUILDING PLANS EXAMINER I
	[email protected]
	561-805-6718

	FBC = FLORIDA BUILDING CODE, 6TH EDITION (2017)
	FBC AMENDED = FLORIDA BUILDING CODE,6TH EDITION (2017)
	FBC B = FBC BUILDING
	FBC EB = FBC EXISTING BUILDING
	FBC A = FBC ACCESSIBILITY
	FBC ENERGY = FBC ENERGY CONSERVATION

	1. [FBC ENERGY C503.1]GENERAL. ALTERATIONS TO ANY
	BUILDING OR STRUCTURE
	SHALL COMPLY WITH THE REQUIREMENTS OF THE CODE FOR NEW
	CONSTRUCTION.
	PROVIDE DOCUMENTATION SUCH AS FORM C402-2017 TO SHOW
	COMPLIANCE

	2. [FBC TABLE 705.8]MAXIMUM AREA OF EXTERIOR WALL
	OPENINGS BASED ON FIRE SEPARATION DISTANCE AND DEGREE
	OF OPENING PROTECTION. PROVIDE SITE PLAN OR SURVEY TO
	SHOW SEPARATION FORM ADJACENT BUILDINGS.

	3. [FBC 1004.1]HOW WAS OCCUPANT LOAD DECREASED FOR A-2
	AREA? A REDUCTION MAY BE REQUESTED TO THE BUILDING
	OFFICIAL, BUT IT WOULD HAVE JUSTIFICATION THAT THE SOME
	AREA WAS NOT USABLE DUE TO REASONS YOU WOULD STATE.
	PLEASE ADJUST YOUR OCCUPANCY FOR THE FULL USE OF THE
	BUILDING AND INCLUDE THE OUTSIDE EATING AREA AS WELL.
	ROOF TOP DINING NEEDS TO SHOW HOW SPACE KEEPS OCCUPANTS
	WITHIN THE AREA DEFINED. PERMANENT GUARDRAILS OR
	SIMILAR PERMANENT STRUCTURE.

	4. [FBC A202.3]ALTERATIONS. WHERE EXISTING ELEMENTS OR
	SPACES OR COMMON AREAS ARE ALTERED, EACH ALTERED
	ELEMENT,
	SPACE OR AREA SHALL COMPLY WITH THE APPLICABLE
	REQUIREMENTS OF CHAPTER 2 AND SECTION 201.1.1.
	IF USING 202.4.1 DIPORPORTIONATE COST TO EXEMPT ACCESS
	TO OUTDOOR SEATING, USE VALUATION OF SHELL WORK PLUS
	BUILD OUT TO DETERMINE THE 20% VALUE OF PROMARY
	FUNCTION.

	5. [FBC A404.2.6]DOORS IN SERIES AND GATES IN SERIES.
	THE DISTANCE BETWEEN TWO HINGED OR PIVOTED DOORS IN
	SERIES AND GATES IN SERIES SHALL BE 48 INCHES (1220 MM)
	MINIMUM PLUS THE WIDTH OF DOORS OR GATES SWINGING INTO
	THE SPACE.
	CHECK DISTANCE BETWEEN EXIT DOOR 103 TO MAIN EXIT 101
	FOR 48 INCHES CLEAR WHEN DOOR 103 IS IN THE OPEN
	POSITION.

	6. [FBC 107.3.5]SHEET A-1.02 CALLS OUT SECTION 2/4.01,
	BUT IT IS SECTION A-A. PLEASE MATCH DETAIL CALL-OUT TO
	SECTION IT REFERS.

	7. [FBC 107.3.5]SEE SECTION 208.1 FOR EXISTING
	PARKING.SHEET A-0.01 IN CODE ANALYSIS EXISTING BLDG
	CLASS, CHANGE CODE REFERENCE TO FBC 2017 6TH EDITION.

	8. [FBC AMENDED 107.3.4.1]PROVIDE PRODUCT APPROVALS FOR
	WINDOWS, WINDOW MULL, STOREFRONT AND DOORS, OR INDICATE
	THAT YOU WOULD LIKE THEM DEFERED.

	9. [FBC AMENDED 107.2.1.2]PROVIDE METAL PAN STAIRCASE
	ENGINEERING, OR INDICATE THAT IT WILL BE A DEFERRED
	SUBMITTAL.

	10. [FBC AMENDED 107.2.1.2]GUARD RAIL ENGINEERING, OR
	INDICATE THAT IT WILL BE DEFERRED.

	NOTE:
	-PLEASE PROVIDE COMMENT RESPONSE SHEET TO EXPLAIN HOW
	EACH COMMENT IS BEING ADDRESSED.
	-ADDITIONAL COMMENTS MAY BE FORTHCOMING PENDING REVIEW
	OF MATERIALS REQUESTED.
	-WHEN RESUBMITTING, PROVIDE TWO IDENTICAL COLLATED SETS
	OF DOCUMENTS FOR ISSUANCE. OLD SHEETS (BOTH SETS)
	SHOULD BE RETAINED IN THE PACKAGE; PLEASE DO NOT
	DISCARD ANY DOCUMENTS. THEY SHOULD BE BOUND TOGETHER
	SEPARATELY FROM THE TWO ISSUANCE SETS AND MARKED "VOID"
	OR "OLD SHEETS". PLEASE DO NOT STAMP THE PLANS VOID AS
	APPLICANTS ARE INADVERTENTLY STAMPING SHEETS THAT WE
	NEED "VOID", RENDERING THEM NOT USABLE.

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2018-10-11			Cont ID
Sent By	jpearson			Date	2018-10-11	Time	15:52	Rev Time	0.00
Received By	jpearson			Date	2018-10-11	Time	15:52	Sent To

Notes

2018-10-11 15:52:46	CODES IN EFFECT:
	FBC = FLORIDA BUILDING CODE 2017 6TH EDITION
	WPB FBC = WEST PALM BEACH AMENDMENTS TO THE FBC 2017
	6TH ED, CHAPTER 1.
	FBC EC = FLORIDA BUILDING CODE ENERGY CONSERVATION 2017
	6TH EDITION
	FBC EX = FLORIDA BUILDING CODE EXISTING BUILDING 2017
	6TH EDITION
	FBC RE = FLORIDA RESIDENTIAL CODE 2017 6TH EDITION
	NEC = NFPA 70 2014 EDITION, NATIONAL ELECTRICAL CODE
	FS = FLORIDA STATUTES

	ELECTRICAL REVIEW STATUS: DENIED, SEE COMMENTS BELOW.

	1. PROVIDE MORE DETAIL FOR WIRE AND CONDUIT SIZES. AS
	AN EXAMPLE, THE OVERHEAD RISER SHOWS (3) 400 MCM IN 3
	INCH CONDUIT. THIS WOULD NOT EQUAL THE NUMBER OR SIZE
	OF WIRES REQUIRED FOR A 120/208, 3 PHASE, 1000 AMP
	SERVICE. ADDITIONALLY, PROVIDE WIRE AND CONDUIT SIZES
	FOR EACH PORTION OF THE FEEDER WIRES AND TAPS TO
	DETERMINE CODE COMPLIANCE. WPB FBC 107.2.1; NEC 240.21,
	310.15(B)(16)
	2. RISER DIAGRAM SHOWS PANEL 1, 2, AND 3. PANEL
	SCHEDULES PROVIDED SHOW PANEL 1, 2, AND HP. PROVIDE
	CLARIFICATION AND CORRECTION. WPB FBC 107.2.1
	3. LOCATION OF SERVICE DISCONNECTS AND METERS ARE NOT
	SHOWN ON PLAN. PROVIDE CORRECTION. WPB FBC 107.2.1
	4. RISER DIAGRAM SHOWS A 400 AMP METER FEEDING PANEL 1
	WITH NO DISCONNECT/OVERCURRENT PROTECTION FOR THE
	CONDUCTORS. WHAT IS THE DISTANCE OF THIS WIRE RUN AND
	WHICH TAP RULE WILL APPLY? PROVIDE CLARIFICATION AND/OR
	CORRECTION. NEC 240.21; WPB FBC 107.2.1
	5. IT APPEARS THIS PROJECT IS FOR SHELL ONLY. PROVIDE
	JUSTIFICATION FOR SERVICE SIZE. HOW IS THE LOAD
	DETERMINED? NEC 220; WPB FBC 107.2.1
	6. VALUE FOR WORK STATED ON PERMIT APPLICATION APPEARS
	LOW. PROVIDE COPY OF SIGNED CONTRACT WITH SCOPE AND
	VALUE OF WORK, TO INCLUDE ALL MATERIALS AND LABOR. THIS
	IS FOR TOTAL PROJECT, NOT JUST ELECTRICAL. FBC 109.3

	END OF COMMENTS.

	PLEASE NOTE: SUBMITTAL OF ADDITIONAL AND/OR REVISED
	MATERIALS MAY RESULT IN NEW PLAN REVIEW COMMENTS. WHEN
	RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RESUBMITTAL FORM. ADDITIONALLY, INSERT CORRECTED PAGES
	INTO THE ORIGINAL SUBMITTAL AND REMOVE THE PREVIOUSLY
	REVIEWED SHEETS. ONE COPY OF THE PREVIOUSLY REVIEWED
	SHEETS SHOULD REMAIN IN PACKAGE AND BE MARKED OLD
	SHEETS.

	SINCERELY,

	JOHN PEARSON
	ELECTRICAL PLANS EXAMINER
	561-805-6746
	[email protected]

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2018-10-10			Cont ID
Sent By	pleduc			Date	2018-10-10	Time		Rev Time	0.00
Received By	pleduc			Date	2018-10-05	Time	15:30	Sent To

Notes

2018-10-10 13:22:16	THIS PLAN WAS REVIEWED AND FAILED BY PETER LEDUC, FIRE
	MARSHAL, WITH THE FOLLOWING COMMENTS:

	HOWEVER,

	1) THIS REVIEW MAY BE APPROVED FOR THE PROPOSED DEMO
	WORK ONLY.

	SHEET 001 - THERE ARE INDICATIONS UNDER THE SCOPE OF
	WORK AND HISTORICAL STATUS THAT SELECTIVE DEMOLITION
	SHALL TAKE PLACE PRIOR TO A TENANT REUSE SUBMITTAL AT A
	LATER DATE.

	THIS APPROVAL WOULD NOT INCLUDE THE PLANS SHEETS FOR
	THE PROPOSED TENANT SPACES.

	SHOULD THE INTENT BE FOR ONLY DEMO WORK PLEASE PROVIDE
	A WRITTEN NARRATIVE TO DO ONLY DEMO WORK AND TO ADDRESS
	THE COMMENTS BELOW IN REVISONS PRIOR TO RECONSTRUCTION.


	*******************************************************
	************************************************




	THE FOLLOWING ARE COMMENTS RELATED TO THE PROPOSED
	TENANT SPACES IN REVIEW OF THE FLORIDA FIRE PREVENTION
	CODE, NFPA 1 AND 101, 2015 ED.


	1) SHEET 001 & A SHEETS - THERE APPEARS TO BE MUTIPLE
	OCCUPANCIES PROPOSED FOR THE TENANT SPACES. WILL THESE
	OCCUPANCIES BE MIXED OR SEPARATED.

	PER NFPA 101, CHPATER 6, OCCUPANCY CLASSIFICATION.

	6.1 CLASSIFICATION OF OCCUPANCY.
	6.1.1 GENERAL.
	6.1.1.1 OCCUPANCY CLASSIFICATION. THE OCCUPANCY OF A
	BUILDING OR
	STRUCTURE, OR PORTION OF A BUILDING OR STRUCTURE, SHALL
	BE CLASSIFIED IN
	ACCORDANCE WITH 6.1.2 THROUGH 6.1.13. OCCUPANCY
	CLASSIFICATION SHALL BE
	SUBJECT TO THE RULING OF THE AUTHORITY HAVING
	JURISDICTION WHERE THERE IS A
	QUESTION OF PROPER CLASSIFICATION IN ANY INDIVIDUAL
	CASE.

	6.1.14.2 DEFINITIONS.
	6.1.14.2.1 MULTIPLE OCCUPANCY. A BUILDING OR STRUCTURE
	IN WHICH TWO
	OR MORE CLASSES OF OCCUPANCY EXIST.
	6.1.14.2.2 MIXED OCCUPANCY. A MULTIPLE OCCUPANCY WHERE
	THE
	OCCUPANCIES ARE INTERMINGLED.
	6.1.14.2.3 SEPARATED OCCUPANCY. A MULTIPLE OCCUPANCY
	WHERE THE
	OCCUPANCIES ARE SEPARATED BY FIRE RESISTANCE?RATED
	ASSEMBLIES.
	6.1.14.3 MIXED OCCUPANCIES.
	6.1.14.3.1 EACH PORTION OF THE BUILDING SHALL BE
	CLASSIFIED AS TO ITS USE IN
	ACCORDANCE WITH SECTION 6.1.
	6.1.14.3.2* THE BUILDING SHALL COMPLY WITH THE MOST
	RESTRICTIVE
	REQUIREMENTS OF THE OCCUPANCIES INVOLVED, UNLESS
	SEPARATE SAFEGUARDS
	ARE APPROVED.
	6.1.14.4 SEPARATED OCCUPANCIES. (SEE ALSO 6.1.14.1.2.)
	6.1.14.4.1 WHERE SEPARATED OCCUPANCIES ARE PROVIDED,
	EACH PART OF THE
	BUILDING COMPRISING A DISTINCT OCCUPANCY, AS DESCRIBED
	IN THIS CHAPTER,
	SHALL BE COMPLETELY SEPARATED FROM OTHER OCCUPANCIES BY
	FIRE-RESISTIVE
	ASSEMBLIES, AS SPECIFIED IN 6.1.14.4.2, 6.1.14.4.3,
	TABLE 6.1.14.4.1(A),
	AND TABLE 6.1.14.4.1(B), UNLESS SEPARATION IS PROVIDED
	BY APPROVED
	EXISTING SEPARATIONS OR AS OTHERWISE PERMITTED BY
	6.1.14.4.6.

	6.1.14.4.3 THE MINIMUM FIRE RESISTANCE RATING SPECIFIED
	IN TABLE
	6.1.14.4.1(A) AND TABLE 6.1.14.4.1(B) SHALL BE
	PERMITTED TO BE
	REDUCED BY 1 HOUR, BUT IN NO CASE SHALL IT BE REDUCED
	TO LESS THAN 1
	HOUR, WHERE THE BUILDING IS PROTECTED THROUGHOUT BY AN
	APPROVED
	AUTOMATIC SPRINKLER SYSTEM IN ACCORDANCE WITH
	9.7.1.1(1) AND
	SUPERVISED IN ACCORDANCE WITH 9.7.2, UNLESS PROHIBITED
	BY THE
	DOUBLE-DAGGER FOOTNOTE ENTRIES IN THE TABLES.
	6.1.14.4.4 OCCUPANCY SEPARATIONS SHALL BE VERTICAL,
	HORIZONTAL, OR
	BOTH OR, WHEN NECESSARY, OF SUCH OTHER FORM AS REQUIRED
	TO PROVIDE
	COMPLETE SEPARATION BETWEEN OCCUPANCY DIVISIONS IN THE
	BUILDING.
	6.1.14.4.5* EACH SEPARATED PORTION OF THE BUILDING
	SHALL COMPLY
	WITH THE REQUIREMENTS FOR THE OCCUPANCY THEREIN.


	PLEASE REVIEW AND CORRECT OR JUSITFY WITH SPECIFIC CODE
	REFERENCES.



	2) SHEET A 0.02 - TWO EXITS ARE SHOWN ON FLOORS 2 AND 3
	HOWEVER, THEY DO NOT MEET THE REQUIRED EXIT SEPARATION
	PER NFPA 101, CHAPTER 7 MEANS OF EGRESS.

	38.2.4 NUMBER OF MEANS OF EGRESS.
	38.2.4.1 MEANS OF EGRESS SHALL COMPLY WITH ALL OF THE
	FOLLOWING, EXCEPT
	AS OTHERWISE PERMITTED BY 38.2.4.2 THROUGH 38.2.4.6:
	(1) THE NUMBER OF MEANS OF EGRESS SHALL BE IN
	ACCORDANCE WITH
	SECTION 7.4.
	(2) NOT LESS THAN TWO SEPARATE EXITS SHALL BE PROVIDED
	ON EVERY STORY.
	(3) NOT LESS THAN TWO SEPARATE EXITS SHALL BE
	ACCESSIBLE FROM EVERY
	PART OF EVERY STORY.


	7.5.1.3.1 WHERE MORE THAN ONE EXIT, EXIT ACCESS, OR
	EXIT DISCHARGE IS
	REQUIRED FROM A BUILDING OR PORTION THEREOF, SUCH
	EXITS, EXIT ACCESSES,
	OR EXIT DISCHARGES SHALL BE REMOTELY LOCATED FROM EACH
	OTHER AND BE
	ARRANGED TO MINIMIZE THE POSSIBILITY THAT MORE THAN ONE
	HAS THE
	POTENTIAL TO BE BLOCKED BY ANY ONE FIRE OR OTHER
	EMERGENCY
	CONDITION.
	7.5.1.3.2* WHERE TWO EXITS, EXIT ACCESSES, OR EXIT
	DISCHARGES ARE
	REQUIRED, THEY SHALL BE LOCATED AT A DISTANCE FROM ONE
	ANOTHER NOT
	LESS THAN ONE-HALF THE LENGTH OF THE MAXIMUM OVERALL
	DIAGONAL
	DIMENSION OF THE BUILDING OR AREA TO BE SERVED,
	MEASURED IN A
	STRAIGHT LINE BETWEEN THE NEAREST EDGE OF THE EXITS,
	EXIT ACCESSES, OR
	EXIT DISCHARGES, UNLESS OTHERWISE PROVIDED IN 7.5.1.3.3
	THROUGH
	7.5.1.3.5.

	PLEASE REVIEW AND CORRECT OR JUSTIFY WITH SPECIFIC CODE
	REFERENCES.



	3) SHEET 1.04 - THERE IS ONLY ONE EXIT INDICATED FROM
	THE ROOF PATIO, TWO ARE REQUIRED.

	PER NFPA 101, CHAPTER 38, NEW BUSINESS OCCUPANCIES

	38.2.4 NUMBER OF MEANS OF EGRESS.
	38.2.4.1 MEANS OF EGRESS SHALL COMPLY WITH ALL OF THE
	FOLLOWING, EXCEPT
	AS OTHERWISE PERMITTED BY 38.2.4.2 THROUGH 38.2.4.6:
	(1) THE NUMBER OF MEANS OF EGRESS SHALL BE IN
	ACCORDANCE WITH
	SECTION 7.4.
	(2) NOT LESS THAN TWO SEPARATE EXITS SHALL BE PROVIDED
	ON EVERY STORY.
	(3) NOT LESS THAN TWO SEPARATE EXITS SHALL BE
	ACCESSIBLE FROM EVERY
	PART OF EVERY STORY.


	7.5.1.3.1 WHERE MORE THAN ONE EXIT, EXIT ACCESS, OR
	EXIT DISCHARGE IS
	REQUIRED FROM A BUILDING OR PORTION THEREOF, SUCH
	EXITS, EXIT ACCESSES,
	OR EXIT DISCHARGES SHALL BE REMOTELY LOCATED FROM EACH
	OTHER AND BE
	ARRANGED TO MINIMIZE THE POSSIBILITY THAT MORE THAN ONE
	HAS THE
	POTENTIAL TO BE BLOCKED BY ANY ONE FIRE OR OTHER
	EMERGENCY
	CONDITION.
	7.5.1.3.2* WHERE TWO EXITS, EXIT ACCESSES, OR EXIT
	DISCHARGES ARE
	REQUIRED, THEY SHALL BE LOCATED AT A DISTANCE FROM ONE
	ANOTHER NOT
	LESS THAN ONE-HALF THE LENGTH OF THE MAXIMUM OVERALL
	DIAGONAL
	DIMENSION OF THE BUILDING OR AREA TO BE SERVED,
	MEASURED IN A
	STRAIGHT LINE BETWEEN THE NEAREST EDGE OF THE EXITS,
	EXIT ACCESSES, OR
	EXIT DISCHARGES, UNLESS OTHERWISE PROVIDED IN 7.5.1.3.3
	THROUGH
	7.5.1.3.5.

	PLEASE REVIEW AND CORRECT OR JUSTIFY WITH SPECIFIC CODE
	REFERENCES.



	4) SHEET E 2 & E 3 - THERE NO INDICATIONS OF EMERGENCY
	LIGHTING.

	PER NFPA 101, CHAPTER 38, NEW BUSINESS OCCUPANCIES

	38.2.9 EMERGENCY LIGHTING.
	38.2.9.1 EMERGENCY LIGHTING SHALL BE PROVIDED IN
	ACCORDANCE
	WITH SECTION 7.9 IN ANY BUILDING WHERE ANY ONE OF THE
	FOLLOWING
	CONDITIONS EXISTS:
	(1) THE BUILDING IS THREE OR MORE STORIES IN HEIGHT.
	(2) THE OCCUPANCY IS SUBJECT TO 50 OR MORE OCCUPANTS
	ABOVE OR
	BELOW THE LEVEL OF EXIT DISCHARGE.
	(3) THE OCCUPANCY IS SUBJECT TO 300 OR MORE TOTAL
	OCCUPANTS.

	7.9 EMERGENCY LIGHTING.
	7.9.1 GENERAL.
	7.9.1.1* EMERGENCY LIGHTING FACILITIES FOR MEANS OF
	EGRESS SHALL BE
	PROVIDED IN ACCORDANCE WITH SECTION 7.9 FOR THE
	FOLLOWING:
	(1) BUILDINGS OR STRUCTURES WHERE REQUIRED IN CHAPTERS
	11 THROUGH 43
	(2) UNDERGROUND AND LIMITED ACCESS STRUCTURES AS
	ADDRESSED IN SECTION
	11.7
	(3) HIGH-RISE BUILDINGS AS REQUIRED BY OTHER SECTIONS
	OF THIS CODE
	(4) DOORS EQUIPPED WITH DELAYED-EGRESS LOCKS
	(5) STAIR SHAFTS AND VESTIBULES OF SMOKEPROOF
	ENCLOSURES, FOR WHICH THE
	FOLLOWING ALSO APPLY:
	(A) THE STAIR SHAFT AND VESTIBULE SHALL BE PERMITTED TO
	INCLUDE A
	STANDBY GENERATOR THAT IS INSTALLED FOR THE SMOKEPROOF
	ENCLOSURE MECHANICAL VENTILATION EQUIPMENT.
	(B) THE STANDBY GENERATOR SHALL BE PERMITTED TO BE USED
	FOR THE
	STAIR SHAFT AND VESTIBULE EMERGENCY LIGHTING POWER
	SUPPLY.
	(6) NEW ACCESS-CONTROLLED EGRESS DOORS IN ACCORDANCE
	WITH 7.2.1.6.2
	7.9.1.2 FOR THE PURPOSES OF 7.9.1.1, EXIT ACCESS SHALL
	INCLUDE ONLY
	DESIGNATED STAIRS, AISLES, CORRIDORS, RAMPS,
	ESCALATORS, AND PASSAGEWAYS
	LEADING TO AN EXIT. FOR THE PURPOSES OF 7.9.1.1, EXIT
	DISCHARGE SHALL
	INCLUDE ONLY DESIGNATED STAIRS, RAMPS, AISLES,
	WALKWAYS, AND ESCALATORS
	LEADING TO A PUBLIC WAY.

	PLEASE REVIEW AND CORRECT OR JUSTIFY WITH SPECIFIC CODE
	REFERENCES.



	5) SHEET E2 & E3 - THE ARE NO INDICATIONS OF LIGHTING
	THE MEANS OF EGRESS

	38.2.8 ILLUMINATION OF MEANS OF EGRESS. MEANS OF EGRESS
	SHALL
	BE ILLUMINATED IN ACCORDANCE WITH SECTION 7.8.

	7.8 ILLUMINATION OF MEANS OF EGRESS.
	7.8.1 GENERAL.
	7.8.1.1* ILLUMINATION OF MEANS OF EGRESS SHALL BE
	PROVIDED IN
	ACCORDANCE WITH SECTION 7.8 FOR EVERY BUILDING AND
	STRUCTURE WHERE
	REQUIRED IN CHAPTERS 11 THROUGH 43. FOR THE PURPOSES OF
	THIS
	REQUIREMENT, EXIT ACCESS SHALL INCLUDE ONLY DESIGNATED
	STAIRS, AISLES,
	CORRIDORS, RAMPS, ESCALATORS, AND PASSAGEWAYS LEADING
	TO AN EXIT. FOR THE
	PURPOSES OF THIS REQUIREMENT, EXIT DISCHARGE SHALL
	INCLUDE ONLY
	DESIGNATED STAIRS, AISLES, CORRIDORS, RAMPS,
	ESCALATORS, WALKWAYS, AND EXIT
	PASSAGEWAYS LEADING TO A PUBLIC WAY.
	7.8.1.2 ILLUMINATION OF MEANS OF EGRESS SHALL BE
	CONTINUOUS DURING THE
	TIME THAT THE CONDITIONS OF OCCUPANCY REQUIRE THAT THE
	MEANS OF EGRESS
	BE AVAILABLE FOR USE, UNLESS OTHERWISE PROVIDED IN
	7.8.1.2.2.




	6) IS IT THE INTENT TO PROVIDE FIRE ALARM AND FIRE
	SPRINKLER SYSTEMS TO THE PROPOSED TENANT SPACES?

	ANY INTENT OF THESE SYSTEMS SHALL COMPLY WITH THE
	REQUIREMENTS OF F.A.C 61G AND BE SUBMITTED WITH THIS
	MASTER PERMIT. SHOP DRAWINGS WILL BE REQUIRED ON A
	FUTURE SUBMITTAL BY QUALFIED CONTRACTORS.

	61G15-32.008 DESIGN OF FIRE ALARMS, SIGNALING SYSTEMS
	AND CONTROL SYSTEMS.
	(1) FIRE ALARMS, SIGNALING, AND CONTROL SYSTEMS
	INCLUDE, BUT ARE NOT LIMITED TO, FIRE PROTECTION
	SUPERVISION AND ALARM CIRCUITS, ACTIVATION CONTROLS,
	AND REMOTE SIGNALING.
	(2) THE FIRE PROTECTION SYSTEM DESIGN SPECIFICATIONS
	SHALL BE BASED ON APPLICABLE NFPA STANDARDS, WHEN
	AVAILABLE, OR ALTERNATIVE ENGINEERING SOURCES AND GOOD
	ENGINEERING PRACTICE WHEN REQUIRED, AND SHALL COMPLY
	WITH THE PROVISIONS OF RULE 61G15-33.006, F.A.C.
	SPECIFIC AUTHORITY 471.008, 471.033(2) FS.
	LAW IMPLEMENTED 471.033 FS.
	HISTORY--NEW 5-19-93, FORMERLY 21H-32.008.


	61G15-32.003 COMMON REQUIREMENTS TO ALL FIRE PROTECTION
	ENGINEERING
	DOCUMENTS.
	(1) THE FIRE PROTECTION SYSTEM ENGINEERING DOCUMENTS
	SHALL PROVIDE THE ENGINEERING REQUIREMENTS TO BE USED
	IN THE PREPARATION OF THE FIRE PROTECTION SYSTEM LAYOUT
	DOCUMENTS AND TO INDICATE THE NATURE AND SCOPE OF THE
	WORK, AND TO DESCRIBE, DETAIL, DIMENSION, LABEL AND
	DEFINE THE FIRE PROTECTION COMPONENTS, SYSTEM(S),
	MATERIALS, ASSEMBLIES, EQUIPMENT AND ITS STRUCTURAL AND
	UTILITY SUPPORT SYSTEM(S), INSOFAR AS THEY INVOLVE THE
	SAFEGUARDING OF LIFE, HEALTH OR PROPERTY.
	(2) THE FIRE PROTECTION SYSTEM ENGINEERING DOCUMENTS
	SHALL SPECIFY THE APPLICABLE REQUIREMENTS FOR THE
	ACCEPTANCE TESTING OF THE FIRE PROTECTION SYSTEM AND
	COMPONENTS, WHICH SHALL BE BASED UPON APPLICABLE CODES
	AND STANDARDS, WHERE AVAILABLE.
	(3) THE OCCUPANCY OF THE AREA OR DESCRIPTION OF A
	SPECIFIC HAZARD BEING PROTECTED BY THE FIRE PROTECTION
	SYSTEM(S) SHALL BE SHOWN ON THE FIRE PROTECTION SYSTEM
	ENGINEERING DOCUMENTS.
	(4) THE APPLICABLE CODE AND STANDARD TO BE USED IN THE
	PREPARATION OF THE FIRE PROTECTION SYSTEM LAYOUT
	DOCUMENTS SHALL BE SHOWN ON THE FIRE PROTECTION SYSTEM
	ENGINEERING DOCUMENTS. WHEN CODES AND STANDARDS ARE NOT
	AVAILABLE OR APPLICABLE, AND SAID LAYOUT DOCUMENTS ARE
	TO BE BASED ON ENGINEERING JUDGMENT, ANY REASONS AND
	ASSUMPTIONS MADE TO DEVELOP THE FIRE PROTECTION CONCEPT
	SHALL BE IDENTIFIED ON THE FIRE PROTECTION SYSTEM
	ENGINEERING DOCUMENTS.
	(5) STRUCTURAL SUPPORT AND STRUCTURAL OPENINGS REQUIRED
	BY THE FIRE PROTECTION SYSTEM SHALL BE SHOWN ON THE
	FIRE PROTECTION SYSTEM ENGINEERING DOCUMENTS AND SHALL
	BE REFERENCED ON STRUCTURAL ENGINEERING DOCUMENTS.
	(6) WHEN LAYOUT DOCUMENTS CONTAIN MATERIAL DEVIATION
	FROM THE ENGINEER OF RECORD'S FIRE PROTECTION SYSTEM
	ENGINEERING DOCUMENT, SUCH LAYOUT DOCUMENTS ARE NOT
	COMPLIANT UNLESS THEY ARE ACCOMPANIED BY REVISED
	ENGINEERING DOCUMENTS MADE AND SEALED BY THE ENGINEER
	OF RECORD FOR THE FIRE PROTECTION SYSTEM.
	(7) REQUIREMENTS FOR ACTIVATION CONTROL SYSTEMS,
	SEQUENCE, OPERATING PARAMETERS, INTERLOCKS, SAFETY
	RELATED DEVICES, INDICATORS AND ALARMS, SHALL BE SHOWN
	ON THE FIRE PROTECTION SYSTEM ENGINEERING DOCUMENTS,
	UNLESS SHOWN ON OTHER RELATED DOCUMENTS.
	(8) ANY INFORMATION DEEMED APPROPRIATE BY THE ENGINEER
	OF RECORD TO ASSIST THE AUTHORITY HAVING JURISDICTION
	IN UNDERSTANDING THE OWNER?S INTENDED USE AND PROPOSED
	PROTECTION OF THE BUILDING OR FACILITY AND TO PROVIDE
	SUFFICIENT DIRECTION TO THE INSTALLATION CONTRACTOR OR
	OTHER INTERESTED PARTIES REGARDING THE LAYOUT OF THE
	SYSTEM(S), SHALL BE INCLUDED IN THE FIRE PROTECTION
	SYSTEM ENGINEERING DOCUMENTS.
	SPECIFIC AUTHORITY 471.008, 471.033(2), FS
	LAW IMPLEMENTED 471.005(7), 471.033(2), FS
	HISTORY?NEW 5-19-93, FORMERLY 21H-32.003, AMENDED
	4-2-2000, 6-26-01

	61G15-32.004 DESIGN OF WATER BASED FIRE PROTECTION
	SYSTEMS.
	(1) WATER BASED FIRE PROTECTION SYSTEMS INCLUDE, BUT
	ARE NOT LIMITED TO, AUTOMATIC SPRINKLER SYSTEMS OF WET,
	DRY, FINE WATER SPRAY (MIST), MANUAL, AND DELUGE VALVE
	CONTROLLED TYPES, PUMPING SYSTEMS, STANDPIPES, FIRE
	WATER MAINS AND DEDICATED FIRE PROTECTION WATER
	SOURCES.
	(2) TO ENSURE MINIMUM DESIGN QUALITY IN FIRE PROTECTION
	SYSTEM ENGINEERING DOCUMENTS, SAID DOCUMENTS SHALL
	INCLUDE AS A MINIMUM THE FOLLOWING INFORMATION WHEN
	APPLICABLE:
	(A) THE POINT OF SERVICE FOR THE FIRE PROTECTION WATER
	SUPPLY AS DEFINED BY 633.021(18) F.S.
	(B) APPLICABLE NFPA STANDARD TO BE APPLIED, OR IN THE
	CASE WHERE NO SUCH STANDARD EXISTS, THE ENGINEERING
	STUDY, JUDGMENTS, AND/OR PERFORMANCE BASED ANALYSIS AND
	CONCLUSIONS.
	(C) CLASSIFICATION OF HAZARD OCCUPANCY FOR EACH ROOM OR
	AREA.
	(D) DESIGN APPROACH, WHICH INCLUDES SYSTEM TYPE,
	DENSITIES, DEVICE TEMPERATURE RATING, AND SPACING FOR
	EACH SEPARATE 42 HAZARD OCCUPANCY.
	(E) CHARACTERISTICS OF WATER SUPPLY TO BE USED, SUCH AS
	MAIN SIZE AND LOCATION, WHETHER IT IS DEAD-END OR
	CIRCULATING; AND IF DEAD-END, THE DISTANCE TO THE
	NEAREST CIRCULATING MAIN, AS WELL AS ITS MINIMUM
	DURATION AND RELIABILITY FOR THE MOST HYDRAULICALLY
	DEMANDING DESIGN AREA.
	(F) WHEN PRIVATE OR PUBLIC WATER SUPPLIES ARE USED, THE
	FLOW TEST DATA, INCLUDING DATE AND TIME OF TEST, WHO
	CONDUCTED TEST OR SUPPLIED INFORMATION, TEST ELEVATION,
	STATIC GAUGE PRESSURE AT NO FLOW, FLOW RATE WITH
	RESIDUAL GAUGE PRESSURE, HYDRANT BUTT COEFFICIENT, AND
	LOCATION OF TEST IN RELATION TO THE HYDRAULIC POINT OF
	SERVICE.
	(G) VALVING AND ALARM REQUIREMENTS TO MINIMIZE
	POTENTIAL FOR IMPAIRMENTS AND UNRECOGNIZED FLOW OF
	WATER.
	(H) MICROBIAL INDUCED CORROSION (MIC). THE ENGINEER OF
	RECORD SHALL MAKE REASONABLE EFFORTS TO IDENTIFY WATER
	SUPPLIES THAT COULD LEAD TO MICROBIAL INDUCED CORROSION
	(MIC). SUCH EFFORTS MAY CONSIST OF DISCUSSIONS WITH THE
	LOCAL WATER PURVEYOR AND/OR FIRE OFFICIAL, FAMILIARITY
	WITH CONDITIONS IN THE LOCAL AREA, OR LABORATORY
	TESTING OF WATER SUPPLIES. WHEN CONDITIONS ARE FOUND
	THAT MAY RESULT IN MIC CONTAMINATION OF THE FIRE
	PROTECTION PIPING, THE ENGINEER SHALL DESIGN CORRECTIVE
	MEASURES.
	(I) BACKFLOW PREVENTION AND METERING SPECIFICATIONS AND
	DETAILS TO MEET LOCAL WATER PURVEYOR REQUIREMENTS
	INCLUDING MAXIMUM ALLOWABLE PRESSURE DROP.
	(J) QUALITY AND PERFORMANCE SPECIFICATIONS OF ALL YARD
	AND INTERIOR FIRE PROTECTION COMPONENTS.
	(3) CONTRACTOR SUBMITTALS WHICH DEVIATE FROM THE ABOVE
	MINIMUM DESIGN PARAMETERS SHALL BE CONSIDERED MATERIAL
	DEVIATIONS AND REQUIRE SUPPLEMENTAL ENGINEERING
	APPROVAL AND DOCUMENTATION.
	(4) IN THE EVENT THE ENGINEER OF RECORD PROVIDES MORE
	INFORMATION AND DIRECTION THAN IS ESTABLISHED ABOVE, HE
	OR SHE SHALL BE HELD RESPONSIBLE FOR THE TECHNICAL
	ACCURACY OF THE WORK IN ACCORDANCE WITH APPLICABLE
	CODES, STANDARDS, AND SOUND ENGINEERING PRINCIPLES.
	SPECIFIC AUTHORITY 471.008, 471.033(2), FS
	LAW IMPLEMENTED 471.005(7), 471.033(2), FS
	HISTORY?NEW 5-19-93, FORMERLY 21H-32.004, AMENDED
	4-2-2000, 6-26-01, 7-12-05




	7) THERE IS AN ELEVATOR INDICATED AS EXISTING.

	PER NFPA 101 CHAPTER 38

	38.5.3 ELEVATORS, ESCALATORS, AND CONVEYORS. ELEVATORS,
	ESCALATORS, AND CONVEYORS SHALL COMPLY WITH THE
	PROVISIONS OF
	SECTION 9.4.

	9.4.2.2 EXCEPT AS MODIFIED HEREIN, EXISTING ELEVATORS,
	ESCALATORS,
	DUMBWAITERS, AND MOVING WALKS SHALL BE IN ACCORDANCE
	WITH THE
	REQUIREMENTS OF ASME A17.3, SAFETY CODE FOR EXISTING
	ELEVATORS
	AND ESCALATORS.

	9.4.3 FIRE FIGHTERS? EMERGENCY OPERATIONS.

	9.4.3.2 ALL EXISTING ELEVATORS HAVING A TRAVEL DISTANCE
	OF 25 FT
	(7620 MM) OR MORE ABOVE OR BELOW THE LEVEL THAT BEST
	SERVES THE
	NEEDS OF EMERGENCY PERSONNEL FOR FIRE-FIGHTING OR
	RESCUE PURPOSES
	SHALL CONFORM TO THE FIRE FIGHTERS? EMERGENCY
	OPERATIONS
	REQUIREMENTS OF ASME A17.3, SAFETY CODE FOR EXISTING
	ELEVATORS
	AND ESCALATORS.

	PLEASE REVIEW AND CORRECT OR JUSTIFY WITH SPECIFIC CODE
	REFERENCES.




	8) WHEN RESUBMITTING, PLEASE PROVIDE PLAN SHEET
	REVISION CLOUDS OR NUMBERED NARRATIVE RESPONSES TO THE
	ABOVE.


	9) ADDITIONAL COMMENTS MAY BE PROVIDED ON THE
	RE-SUBMITTAL OF THE ABOVE.



	PETER LEDUC
	FIRE MARSHAL
	561-804-4709
	[email protected]

Review Stop	HIST			HISTORICAL
Rev No	1	Status	P	Date	2018-11-21			Cont ID
Sent By	fmittner			Date	2018-11-21	Time	11:36	Rev Time	0.00
Received By	fmittner			Date	2018-11-21	Time	11:36	Sent To

Notes

***NONE***

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2018-11-25			Cont ID
Sent By	cpuell			Date	2018-11-25	Time	11:51	Rev Time	0.00
Received By	cpuell			Date	2018-10-01	Time	09:17	Sent To

Notes

***NONE***

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	1	Status	F	Date	2018-11-14			Cont ID
Sent By	dbattles			Date	2018-11-14	Time	08:54	Rev Time	0.00
Received By	dbattles			Date	2018-11-14	Time	08:54	Sent To

Notes

2018-11-14 08:55:10	[FBC AMENDED 109]PLANS WILL BE REVIEWED BY THE PBC
	IMPACT FEE OFFICE DIGITALLY VIA PROJECTDOX UPON
	NOTIFICATION BY THIS OFFICE. NOTIFICATION MAY OCCUR
	WHEN PLANS ARE NEAREST FINAL FORM. YOU MAY COORDINATE
	WITH THE IMPACT FEE OFFICE AT (561) 233-5025 OR SIMPLY
	UPLOAD THE MUNICIPAL IMPACT FEE QUESTIONNAIRE FORM TO
	YOUR PROJECT AND NAME THE FILE MUNICIPAL IMPACT FEE
	QUESTIONNAIRE. THE FORM CAN BE FOUND AT: HTTP://DISCOVE
	R.PBCGOV.ORG/PZB/ADMINISTRATION/PDF/IMPACTFEES/FORMS/QU
	ESTIONNAIRE.PDF UPON APPROVAL AND FEE PAYMENT, PLEASE
	UPLOAD THE RECEIPT TO YOUR PROJECT OR EMAIL IT TO
	[email protected]

	DYLAN BATTLES
	BUILDING PLANS EXAMINER I
	[email protected]
	561-805-6718

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2018-10-23			Cont ID
Sent By	ccole			Date	2018-10-23	Time	15:47	Rev Time	0.00
Received By	ccole			Date	2018-10-23	Time	15:47	Sent To

Notes

2018-10-23 16:06:58	1ST REVIEW FBC-2017 MECHANICAL
	PERMIT #18081353
	10/23/18

	CODES IN EFFECT:

	FBC B- FLORIDA BUILDING CODE SIXTH EDITION 2017
	FBC M- FLORIDA MECHANICAL CODE SIXTH EDITION 2017
	FBC EC- FLORIDA ENERGY CONSERVATION CODE SIXTH EDITION
	2017
	FBC EX- FLORIDA EXISTING BUILDING CODE SIXTH EDITION
	2017
	FS- FLORIDA STATUTES
	FAC- FLORIDA ADMINISTRATIVE CODE
	WPB- WEST PALM BEACH AMENDMENTS TO THE FBC SIXTH
	EDITION 2017

	PLAN REVIEW RESULTS: DENIED.

	1) PROVIDE AC COOLING AND HEATING CALCULATIONS FOR THE
	NEW SYSTEMS IN ACCORDANCE WITH SECTION C403.2.1 FBC EC.

	2) REFER TO SECTION C505.1 FBC-17 ENERGY CONSERVATION
	AND SUBMIT AN ENERGY EFFICIENCY COMPLIANCE REPORT FOR
	THE CHANGE IN OCCUPANCY FROM S1 TO A2.

	3) SHEET M-1: PLEASE PROVIDE A MORE SPECIFIC OCCUPANCY
	CLASSIFICATION IN THE VENTILATION SCHEDULE FOR THE MAIN
	ROOMS- TABLE 403.3.1.1 FBC M.

	4) M-2: THE SUPPLY AIR DUCTS PENETRATING THE INTERIOR
	EXIT STAIRWAY ARE PROHIBITED PER SECTIONS 1023.5 &
	1023.6 FBC B.

	5) M-2: DUCT SMOKE DETECTORS ARE REQUIRED IN THE SUPPLY
	AIR SYSTEMS OF EACH 5-TON AC SYSTEM PER SECTION 606.2.1
	FBC M. PLEASE NOTE THAT AN EXEMPTION CAN BE APPLIED IF
	THE MANUFACTURER'S SPECIFICATIONS INDICATE SYSTEMS ARE
	NOT CAPABLE OF PRODUCING OVER 2000 CFMS OF SUPPLY AIR.

	WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RE-SUBMITTAL FORM. ADDITIONALLY, PLEASE INSERT
	CORRECTED PLAN SHEETS INTO THE SETS, REMOVE THE
	PREVIOUSLY REVIEWED SHEETS AND MARK VOID ON THEM, AND
	KEEP THEM WITH THE SUBMITTALS

	CHRISTOPHER L. COLE
	MECHANICAL PLANS EXAMINER
	401 CLEMATIS STREET
	WEST PALM BEACH FL 33401
	561-805-6719
	[email protected]

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2018-11-01			Cont ID
Sent By	gjohnson			Date	2018-11-01	Time	16:49	Rev Time	0.00
Received By	gjohnson			Date	2018-11-01	Time	10:21	Sent To

Notes

2018-11-01 16:50:07	ST REVIEW:
	2017 FLORIDA BUILDING CODE 6TH EDITION
	2017 FLORIDA BUILDING CODE - PLUMBING, SIXTH EDITION
	2017 FLORIDA BUILDING CODE - ACCESSIBILITY, SIXTH
	EDITION
	2017 FLORIDA BUILDING CODE - FUEL GAS, SIXTH EDITION
	2017 FLORIDA BUILDING CODE - RESIDENTIAL, SIXTH EDITION
	2017 FLORIDA BUILDING CODE - EXISTING BUILDING, SIXTH
	EDITION
	2017 FLORIDA BUILDING CODE - ENERGY CONSERVATION, SIXTH
	EDITION

	PLUMBING COMMENTS:

	1. THE APPLICATION AND SHT. A-0.01 UNDER SCOPE OF WORK
	STATE A CHANGE OF OCCUPANCY FROM A STORAGE TO ASSEMBLY
	A-2 THE PLUMBING PLAN SHALL COMPLY WITH THE A-2 FIXTURE
	COUNT AND THE REQUIREMENT FOR SEPARATE FACILITIES,
	THERE ARE SOME SHEETS THAT CALL OUT A BUSINESS
	OCCUPANCY THIS SHALL BE CLARIFIED. IF IT IS YOUR INTENT
	TO BUILD A VANILLA SHELL WITH NO OCCUPANCY REQUIREMENTS
	THE PLAN AND THE APPLICATION WILL NEED TO SHOW THIS.
	PER WPB AMEND TO FBC 107.2.1 AND FBC PL TABLE 403.1 AND
	403.2 SEPARATE FACILITIES. WHERE PLUMBING FIXTURES ARE
	REQUIRED, SEPARATE FACILITIES SHALL BE PROVIDED FOR
	EACH SEX.
	2. THE PLUMBING PLANS INCLUDE FIXTURES COMPLIANCE WITH
	ACCESSIBILITY IS REQUIRED PLEASE PROVIDE DETAILS
	SHOWING COMPLIANCE WITH FBC ACC 603, 604.2, 604.3.1,
	604.4, 604.5.1, 604.5.2, 604.7, 606.2, 606.3, 609.4
	3. SHT. P-1 THE MOP SINK ON THE GROUND FLOOR SHALL
	CONNECT DOWNSTREAM OF THE BATHROOM GROUP. PER FBC PL
	912.1
	4. SHT. P-1 THE DRY VENT ON THE GROUND FLOOR SHALL NOT
	RUN HORIZONTAL. PER FBC PL 905.3, 905.4, 905.5
	5. SHT. P-1 THE MOP SINK ON THE 2ND AND 3RD FLOOR SHALL
	HAVE A SEPARATE VENT. . PER FBC PL 901.2.1, 912.1
	6. IF THIS IS GOING TO BE AN R-2 SERVING FOOD IT SHALL
	HAVE A GREASE INTERCEPTOR. PER FBC PL 1003.3.1


	PLEASE NOTE THAT SUBMITTAL OF ADDITIONAL AND/OR REVISED
	MATERIALS MAY RESULT IN NEW PLAN REVIEW COMMENTS.
	WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RE-SUBMITTAL FORM. PLEASE, ADDITIONALLY, INSERT
	CORRECTED PAGES INTO TO SUBMITTAL AND REMOVE OR VOID
	THE PREVIOUSLY REVIEWED SHEETS.

	GEORGE JOHNSON
	PLUMBING PLANS EXAMINER
	CITY OF WEST PALM BEACH
	561-805-6711
	[email protected]

Review Stop	SIGNATURE			ELECTRONIC SIGNATURE SHEET
Rev No	1	Status	F	Date	2018-11-14			Cont ID
Sent By	dbattles			Date	2018-11-14	Time	08:55	Rev Time	0.00
Received By	dbattles			Date	2018-11-14	Time	08:55	Sent To

Notes

2018-11-14 09:01:04	DYLAN BATTLES
	BUILDING PLANS EXAMINER I
	[email protected]
	561-805-6718

	SIGNAURE TO BE VERIFIED WITH RE-SUBMITTAL.

Review Stop	Z			ZONING
Rev No	1	Status	P	Date	2018-11-20			Cont ID
Sent By	aaponte			Date	2018-11-20	Time	15:15	Rev Time	0.00
Received By	aaponte			Date	2018-11-20	Time	15:15	Sent To

Notes

***NONE***