City of West Palm Beach eGovPlus

Plan Review Details - Permit 17020623

Plan Review Stops For Permit 17020623

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	3	Status	P	Date	2017-06-27			Cont ID
Sent By	jwitmer			Date	2017-06-27	Time	06:42	Rev Time	0.00
Received By	jwitmer			Date	2017-06-27	Time	06:01	Sent To

Notes

2017-06-27 06:30:20	BUILDING PLAN REVIEW
	W. P. B. PERMIT: 17020623 CHANGE OF OCCUPANCY!!!
	ADD: 218 CLEMATIS ST.
	CONT: MCL CONSTRUCTION INC.
	TEL: 561-368-2434
	E-MAIL: [email protected]

	2014 FLORIDA BUILDING CODE W 2014 WEST PALM BEACH
	AMENDMENTS TO THE FLORIDA BUILDING CODE, CHAPTER 1,
	ADMINISTRATION

	2014 EXISTING BUILDING CODE LEVEL II 701.3 COMPLIANCE.
	ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS, SYSTEMS, AND
	SPACES SHALL COMPLY WITH THE REQUIREMENTS OF THE
	FLORIDA BUILDING CODE, BUILDING.

	3RD REVIEW
	DATE: TUES. JUNE 27/ 2017
	ACTION: BUILDING PROVISO


	1) BUILDING PROVISO/ DEFERRED SUBMITTAL: 2014 FLORIDA
	BUILDING CODE W 2014 WEST PALM BEACH AMENDMENTS TO THE
	FLORIDA BUILDING CODE, CHAPTER 1, ADMINISTRATION
	CODE105.3.1.2(2) FIRE SPRINKLER DOCUMENTS FOR ANY NEW
	BUILDING OR ADDITION WHICH INCLUDES A FIRE SPRINKLER
	SYSTEM WHICH CONTAINS 50 OR MORE SPRINKLER HEADS. A
	CONTRACTOR I, CONTRACTOR II OR CONTRACTOR IV, CERTIFIED
	UNDER SECTION 633.521, FLORIDA STATUTES, MAY DESIGN A
	FIRE SPRINKLER SYSTEM OF 49 OR FEWER HEADS AND MAY
	DESIGN THE ALTERATION OF AN EXISTING FIRE SPRINKLER
	SYSTEM IF THE ALTERATION CONSISTS OF THE RELOCATION,
	ADDITION OR DELETION OF NOT MORE THAN 49 HEADS, NOT
	WITHSTANDING THE SIZE OF THE EXISTING FIRE SPRINKLER
	SYSTEM.

	2) BUILDING PROVISO/ DEFERRED SUBMITTAL: 2014 FBC-B
	1609.1.2 PROTECTION OF OPENINGS, 1609.6.4.4.1
	COMPONENTS & CLADDING. 61-41,003 ADMINISTRATION AND
	DEPARTMENT RESPONSIBILITIES. (4) TESTING & EVALUATION
	OF PRODUCTS. FL. S. 553.842 PRODUCT EVALUATION AND
	APPROVAL.
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS, ADMINISTRATIVE
	CODE 61G20-3.005, RULE 9N-3 NOV. 01/ 2010 (31)
	SUB-CATEGORY OF PRODUCTS OR CONSTRUCTION SYSTEMS THAT
	WILL REQUIRE PRODUCT APPROVALS:
	(31)(A) EXTERIOR DOORS ,MULLIONS & ROOF HATCHES.
	(B) WINDOWS & MULLIONS
	(C) PANEL WALLS: STOREFRONTS, CURTAIN WALLS, WALL
	LOUVERS, EFIS SYSTEMS,
	(D) ROOFING PRODUCTS AND ASSEMBLIES, ROOF TOP CURBS,
	ROOF TOP VENTILATORS & FANS
	(E) SHUTTERS
	(F) SKYLIGHTS
	(G) EXTERIOR COOLER, FREEZERS & PRE-ENGINEERED A/C
	STANDS

	3) BUILDING PROVISO: FBC 107.3.4.1 PRODUCT APPROVALS.
	THOSE PRODUCTS WHICH ARE REGULATED BY THE DCA RULE
	9N-03 SHALL BE REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD PRIOR TO SUBMITTAL FOR
	JURISDICTIONAL APPROVAL. FL 61G1-23.015 (2) THE
	ARCHITECT IS RESPONSIBLE FOR SUPERVISING AND REVIEWING
	ALL PROJECT DATA, REPORTS, SHOP DRAWINGS ETC..

	4) WELDED OR BOLTED CONNECTIONS. THE CONTRACTOR IS
	REQUIRED TO PROVIDE WELD PROCEDURE SPECIFICATIONS &
	WELDER OPERATOR PERFORMANCE QUALIFICATION RECORDS IN
	ACCORDANCE WITH THE REFERENCED STANDARDS AT TIME OF
	INSPECTION.
	2014 FBC-B 2204.1 WELDING
	2014 FBC-B 2204.2 BOLTING.

	JAMES A. WITMER BN, PX, CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	CONSTRUCTION SERVICES DIVISION / DEVELOPMENT SERVICES
	DEPARTMENT
	401 CLEMATIS ST.
	WEST PALM BEACH. FL 33402
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2017-06-01			Cont ID
Sent By	jwitmer			Date	2017-06-01	Time	16:34	Rev Time	0.00
Received By	jwitmer			Date	2017-06-01	Time	11:29	Sent To

Notes

2017-06-01 16:34:07	BUILDING PLAN REVIEW
	W. P. B. PERMIT: 17020623 CHANGE OF OCCUPANCY!!!
	ADD: 218 CLEMATIS ST.
	CONT: MCL CONSTRUCTION INC.
	TEL: 561-368-2434
	E-MAIL: [email protected]

	2014 FLORIDA BUILDING CODE W 2014 WEST PALM BEACH
	AMENDMENTS TO THE FLORIDA BUILDING CODE, CHAPTER 1,
	ADMINISTRATION

	2014 EXISTING BUILDING CODE LEVEL II 701.3 COMPLIANCE.
	ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS, SYSTEMS, AND
	SPACES SHALL COMPLY WITH THE REQUIREMENTS OF THE
	FLORIDA BUILDING CODE, BUILDING.

	2ND REVIEW
	DATE: THURS. JUNE 01/ 2017
	ACTION: DENIED

	1A-B) COMPLIED.

	1C) NEW COMMENT WHICH DEALS WITH THE AREA INCREASE
	TAKEN FOR FIRE SPRINKLERS, NO PLANS WERE SUBMITTED FOR
	FIRE SPRINKLERS. W. P. B. ADMINISTRATIVE
	CODE105.3.1.2(2) FIRE SPRINKLER DOCUMENTS FOR ANY NEW
	BUILDING OR ADDITION WHICH INCLUDES A FIRE SPRINKLER
	SYSTEM WHICH CONTAINS 50 OR MORE SPRINKLER HEADS. A
	CONTRACTOR I, CONTRACTOR II OR CONTRACTOR IV, CERTIFIED
	UNDER SECTION 633.521, FLORIDA STATUTES, MAY DESIGN A
	FIRE SPRINKLER SYSTEM OF 49 OR FEWER HEADS AND MAY
	DESIGN THE ALTERATION OF AN EXISTING FIRE SPRINKLER
	SYSTEM IF THE ALTERATION CONSISTS OF THE RELOCATION,
	ADDITION OR DELETION OF NOT MORE THAN 49 HEADS, NOT
	WITHSTANDING THE SIZE OF THE EXISTING FIRE SPRINKLER
	SYSTEM.

	2) 2ND REQUEST. PLEASE NOTE THE ENERGY FORMS STATE
	RIGHT BY THE SIGNATURE, THIS SIGNATURE IS AN ELECTRONIC
	SIGNATURE. THE SUBMITTED ENERGY CALS. AND HVAC CALS.
	ARE PRINTED BUT HAVE A DIGITAL SIGNATURE, BY JOHN
	LANGFORD P. E. PLEASE SHOW COMPLIANCE WITH FLORIDA
	ADMINISTRATIVE CODE 61G15-23.005 (3)(C) A SCANNED,
	FACSIMILE, DIGITALLY CREATED OR COPIED IMAGE OF THE
	LICENSEES SIGNATURE SHALL NOT BE USED ON ELECTRONICALLY
	SIGNED AND SEALED ENGINEERING PLANS, SPECIFICATIONS,
	REPORTS OR OTHER DOCUMENTS.

	3) SHEET A0.3 SHOWS 127 INTERIOR SEATS, 26 EXTERIOR
	SEATS AND WHAT MAY APPEAR TO BE 30 FEET OF STANDING AT
	THE BAR, UNDETERMINABLE AMOUNT OF FOOTAGE AND USE?

	3A-C) COMPLIED

	3D) PLEASE NOTE THE FIRE PLAN REVIEWERS NOTES ON THE
	FIRE PIT. THE PLANS SHOW IN THE CENTER OF THE PLAN A
	INDOOR FIRE PIT, PLEASE PROVIDE THE TYPE OF FUEL,
	AMOUNT OF FUEL AND THE AMOUNT OF BTU?S WILL BE USED PER
	HOUR. 107.2.1.3. ADDITIONAL INFORMATION IS REQUIRED.

	4-6) COMPLIED.

	7A) SEMI-COMPLIED. IT IS TRUE THE FRONT ENTRY DOOR DOES
	NOT REQUIRE PANIC HARDWARE BUT THE HARDWARE DOES NEED
	TO COMPLY WITH : 2014 FBC-B SECTION 1008.1.9.3(2)
	2. IN BUILDINGS IN OCCUPANCY GROUP A HAVING AN OCCUPANT
	LOAD OF 300 OR LESS, GROUPS B, F, M AND S, AND IN
	PLACES OF RELIGIOUS WORSHIP, THE MAIN EXTERIOR DOOR OR
	DOORS ARE PERMITTED TO BE EQUIPPED WITH KEY-OPERATED
	LOCKING DEVICES FROM THE EGRESS SIDE PROVIDED:

	2.1. THE LOCKING DEVICE IS READILY DISTINGUISHABLE AS
	LOCKED;

	2.2. A READILY VISIBLE DURABLE SIGN IS POSTED ON THE
	EGRESS SIDE ON OR ADJACENT TO THE DOOR STATING: THIS
	DOOR TO REMAIN UNLOCKED WHEN BUILDING IS OCCUPIED. THE
	SIGN SHALL BE IN LETTERS 1 INCH (25 MM) HIGH ON A
	CONTRASTING BACKGROUND; AND

	2.3. THE USE OF THE KEY-OPERATED LOCKING DEVICE IS
	REVOKABLE BY THE BUILDING OFFICIAL FOR DUE CAUSE.

	7B) THE REAR EXIT DOOR NOT LABELED ON SHEET A0.5 AND
	NOT INCLUDED IN THE DOOR SCHEDULE SHEET A7.1 DOES
	INDICATE A DOOR 108 TO BE VERIFIED PANIC HARDWARE IS
	REQUIRED. PLEASE IDENTIFY THE DOOR ON SHEET A0.5.

	8) COMPLIED.

	8A) NEW COMMENT DEALS WITH A0.5 THE AWNING OVER THE
	PUBLIC SIDEWALK AND HOW CLOSE THE CURB IS TO THE
	AWNING. THE CURB IS NOT SHOWN IN THE DEPICTED PLAN.
	COMPLIANCE WITH 2014 FBC-B SECTION 3202.3.1 CANNOT BE
	DETERMINED.
	3202.3.1 AWNINGS, CANOPIES, MARQUEES AND SIGNS.
	AWNINGS, CANOPIES, MARQUEES AND SIGNS SHALL BE
	CONSTRUCTED SO AS TO SUPPORT APPLICABLE LOADS AS
	SPECIFIED IN CHAPTER 16. AWNINGS, CANOPIES, MARQUEES
	AND SIGNS WITH LESS THAN 15 FEET (4572 MM) CLEARANCE
	ABOVE THE SIDEWALK SHALL NOT EXTEND INTO OR OCCUPY MORE
	THAN TWO-THIRDS THE WIDTH OF THE SIDEWALK MEASURED FROM
	THE BUILDING. STANCHIONS OR COLUMNS THAT SUPPORT
	AWNINGS, CANOPIES, MARQUEES AND SIGNS SHALL BE LOCATED
	NOT LESS THAN 2 FEET (610 MM) IN FROM THE CURB LINE.


	9) BUILDING PROVISO: 2014 FBC-B 1609.1.2 PROTECTION OF
	OPENINGS, 1609.6.4.4.1 COMPONENTS & CLADDING. 61-41,003
	ADMINISTRATION AND DEPARTMENT RESPONSIBILITIES. (4)
	TESTING & EVALUATION OF PRODUCTS. FL. S. 553.842
	PRODUCT EVALUATION AND APPROVAL.
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS, ADMINISTRATIVE
	CODE 61G20-3.005, RULE 9N-3 NOV. 01/ 2010 (31)
	SUB-CATEGORY OF PRODUCTS OR CONSTRUCTION SYSTEMS THAT
	WILL REQUIRE PRODUCT APPROVALS:
	(31)(A) EXTERIOR DOORS ,MULLIONS & ROOF HATCHES.
	(B) WINDOWS & MULLIONS
	(C) PANEL WALLS: STOREFRONTS, CURTAIN WALLS, WALL
	LOUVERS, EFIS SYSTEMS,
	(D) ROOFING PRODUCTS AND ASSEMBLIES, ROOF TOP CURBS,
	ROOF TOP VENTILATORS & FANS
	(E) SHUTTERS
	(F) SKYLIGHTS
	(G) EXTERIOR COOLER, FREEZERS & PRE-ENGINEERED A/C
	STANDS

	10) BUILDING PROVISO: FBC 107.3.4.1 PRODUCT APPROVALS.
	THOSE PRODUCTS WHICH ARE REGULATED BY THE DCA RULE
	9N-03 SHALL BE REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD PRIOR TO SUBMITTAL FOR
	JURISDICTIONAL APPROVAL. FL 61G1-23.015 (2) THE
	ARCHITECT IS RESPONSIBLE FOR SUPERVISING AND REVIEWING
	ALL PROJECT DATA, REPORTS, SHOP DRAWINGS ETC..

	11) SEMI-COMPLIED. THE ROOF TOP EXHAUST FAN DOES HAVE A
	DETAIL FOR ANCHORING OF THE FAN TO THE CURB AND CURB TO
	THE ROOF FRAMING. THE MECHANICAL REVIEWER REQUEST
	DETAILS AS WELL FOR THE NEW ROOF TOP CONDENSERS TO THE
	EXISTING STANDS.
	ROOF TOP A/C STANDS WILL NEED TO SUPPLY THE FOLLOWING
	INFORMATION, CALCULATE THE AREA OF THE ROOF TOP
	COMPRESSORS, THE MEAN ROOF HEIGHT OF THE STAND AND
	COMPRESSORS, WEIGHT, CIRCLED THE DESIGN PARAMETERS IN
	THE TABLES , ANCHORS AND UPLIFT VERSES MOMENT. 2014
	FBC-B 1604.4 ANALYSIS.

	12) WELDED OR BOLTED CONNECTIONS. THE CONTRACTOR IS
	REQUIRED TO PROVIDE WELD PROCEDURE SPECIFICATIONS &
	WELDER OPERATOR PERFORMANCE QUALIFICATION RECORDS IN
	ACCORDANCE WITH THE REFERENCED STANDARDS AT TIME OF
	INSPECTION.
	2014 FBC-B 2204.1 WELDING
	2014 FBC-B 2204.2 BOLTING.


	12) BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
	FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
	PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
	A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
	APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	13) WHEN RESUBMITTING PLANS PLEASE INDICATE THE
	REVISION & REMOVE ANY VOIDED SHEETS & REPLACE ANY PAGES
	AS NECESSARY, COLLATE AND STAPLE INTO SETS OF PLANS. A
	TRANSMITTAL LETTER LISTING THE ORIGINAL REVIEW COMMENT
	NUMBER, WITH A DESCRIPTION OF THE REVISION MADE,
	IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE THE
	CHANGES CAN BE FOUND WILL HELP TO EXPEDITE YOUR PERMIT.
	THANK YOU FOR YOUR ANTICIPATED COOPERATION.

	JAMES A. WITMER BN, PX, CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	CONSTRUCTION SERVICES DIVISION / DEVELOPMENT SERVICES
	DEPARTMENT
	401 CLEMATIS ST.
	WEST PALM BEACH. FL 33402
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2017-03-17			Cont ID
Sent By	jwitmer			Date	2017-03-17	Time	13:47	Rev Time	0.00
Received By	jwitmer			Date	2017-03-14	Time	08:07	Sent To

Notes

2017-03-17 13:47:10	BUILDING PLAN REVIEW
	W. P. B. PERMIT: 17020623 CHANGE OF OCCUPANCY!!!
	ADD: 218 CLEMATIS ST.
	CONT: MCL CONSTRUCTION INC.
	TEL: 561-368-2434
	E-MAIL: [email protected]

	2014 FLORIDA BUILDING CODE W 2014 WEST PALM BEACH
	AMENDMENTS TO THE FLORIDA BUILDING CODE, CHAPTER 1,
	ADMINISTRATION

	2014 EXISTING BUILDING CODE LEVEL II 701.3 COMPLIANCE.
	ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS, SYSTEMS, AND
	SPACES SHALL COMPLY WITH THE REQUIREMENTS OF THE
	FLORIDA BUILDING CODE, BUILDING.

	1ST REVIEW
	DATE: FRI. MARCH 17/ 2017
	ACTION: DENIED

	1A) THE COVERSHEET LIST THE FLOOR RATING AS A1.0 HOUR
	FIRE RATING PER TABLE 601 OF THE 2014 FBC-B. THE
	COVERSHEET DOES NOT LIST ANY CRITERIA FOR HORIZONTAL
	ASSEMBLIES OR OCCUPANCY SEPARATION FOR HORIZONTAL
	ASSEMBLIES SEPARATING THE A2 ASSEMBLY USE AND THE
	BUSINESS OCCUPANCY ON THE 2ND FLOOR. PLEASE REVIEW
	TABLE 707.310 OF THE FBC-B THE REQUIREMENT FOR 2 HOUR
	FIRE SEPARATION BETWEEN THE HORIZONTAL ASSEMBLIES
	BETWEEN FIRE AREAS. THIS IS A MIXED USE BUILDING PLEASE
	PROVIDE THE TOTAL SQ. FT. FOR EACH OCCUPANCY PER FLOOR
	AND 508.4.2 ALLOWABLE BUILDING AREA. IN EACH STORY, THE
	BUILDING AREA SHALL BE SUCH THAT THE SUM OF THE RATIOS
	OF THE ACTUAL BUILDING AREA OF EACH SEPARATED OCCUPANCY
	DIVIDED BY THE ALLOWABLE BUILDING AREA OF EACH
	SEPARATED OCCUPANCY SHALL NOT EXCEED 1.

	1B) IN THE EXISTING BUILDING CODE SECTION 1012.5.1 FIRE
	WALL ALTERNATIVE FOR HORIZONTAL ASSEMBLIES THERE ARE
	(3) REQUIREMENTS IF ALL (3) REQUIREMENTS ARE MET THAN
	THE HORIZONTAL ASSEMBLIES CAN BE REDUCED TO (1) HOUR.
	PLEASE NOTE THIS TENANT SPACE IS ONLY (1) TENANT SPACE
	OF THE BUILDING ADDRESSED 230 CLEMATIS WITH 18,317
	SQUARE FEET ON THE 1ST FLOOR AND 14,344 ON THE SECOND
	FLOOR.

	2) THE SUBMITTED ENERGY CALS. AND HVAC CALS. ARE
	PRINTED BUT HAVE A DIGITAL SIGNATURE, BY JOHN LANGFORD
	P. E. PLEASE SHOW COMPLIANCE WITH FLORIDA
	ADMINISTRATIVE CODE 61G15-23.005 (3)(C) A SCANNED,
	FACSIMILE, DIGITALLY CREATED OR COPIED IMAGE OF THE
	LICENSEE?S SIGNATURE SHALL NOT BE USED ON
	ELECTRONICALLY SIGNED AND SEALED ENGINEERING PLANS,
	SPECIFICATIONS, REPORTS OR OTHER DOCUMENTS.

	3) SHEET A0.3 SHOWS 127 INTERIOR SEATS, 26 EXTERIOR
	SEATS AND WHAT MAY APPEAR TO BE 30 FEET OF STANDING AT
	THE BAR, UNDETERMINABLE AMOUNT OF FOOTAGE AND USE?

	3A) PLANS SHOW 8 ACCESSIBLE SEATING AREAS. THE UNKNOWN
	IS THE USAGE OF THE 30 FEET OF BAR APPEARS TO BE
	STANDING ROOM? COMPLIANCE WITH FBC-ACCESS. CODE 226.1.
	WHERE DINING SURFACES ARE PROVIDED FOR THE CONSUMPTION
	OF FOOD OR DRINK, AT LEAST 5 PERCENT OF THE SEATING
	SPACES AND STANDING SPACES AT THE DINING SURFACES SHALL
	COMPLY WITH 902.

	3B) SEMI-COMPLIED. THE UNKNOWN IS THE USAGE OF THE 30
	FEET OF BAR APPEARS TO BE STANDING ROOM?
	PLEASE SHOW COMPLIANCE WITH THE 2014 FBC-ACCESS. CODE
	226.2 DISPERSION. DINING SURFACES REQUIRED TO COMPLY
	WITH 902 SHALL BE DISPERSED THROUGHOUT THE SPACE OR
	FACILITY.

	3C) PLEASE SHOW COMPLIANCE WITH THE 2014 FBC-ACCESS.
	CODE 902.1. DINING SURFACES AND WORK SURFACES SHALL
	COMPLY WITH 902.2 AND 902.3.
	3C)(1) 902.2 CLEAR FLOOR OR GROUND SPACE. A CLEAR FLOOR
	SPACE COMPLYING WITH 305 POSITIONED FOR A FORWARD
	APPROACH SHALL BE PROVIDED. KNEE AND TOE CLEARANCE
	COMPLYING WITH 306 SHALL BE PROVIDED.

	3C)(2) 902.3 HEIGHT. THE TOPS OF DINING SURFACES AND
	WORK SURFACES SHALL BE 28 INCHES MINIMUM AND 34 INCHES
	MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.

	3D) THE PLANS SHOW IN THE CENTER OF THE PLAN A INDOOR
	FIRE PIT, PLEASE PROVIDE THE TYPE OF FUEL, AMOUNT OF
	FUEL AND THE AMOUNT OF BTU?S WILL BE USED PER HOUR.
	107.2.1.3. ADDITIONAL INFORMATION IS REQUIRED.

	4)SHEET A0.6 THE DETAIL MOUNTING HEIGHTS SHOWS SIGNAGE
	LOCATED CENTER LINED AT 60 INCHES. PLEASE SHOW
	COMPLIANCE WITH ACCESS. CODE 703.4.1 HEIGHT ABOVE
	FINISH FLOOR OR GROUND. TACTILE CHARACTERS ON SIGNS
	SHALL BE LOCATED 48 INCHES (1220 MM) MINIMUM ABOVE THE
	FINISH FLOOR OR GROUND SURFACE, MEASURED FROM THE
	BASELINE OF THE LOWEST TACTILE CHARACTER AND 60 INCHES
	(1525 MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND
	SURFACE, MEASURED FROM THE BASELINE OF THE HIGHEST
	TACTILE CHARACTER.

	5) SHEET A0.6 THE RESTROOM DETAILS FOR THE WATER CLOSET
	GRAB BARS SHOWS THE DIMENSION TAKEN FROM THE FLOOR TO
	CENTERLINE OF THE GRAB BAR, BE AWARE THE 2014 ACCESS.
	CODE CHANGED THE DIMENSION TO THE TOP OF THE GRASPING
	SURFACE, SEE ACCESS. CODE 609.4.

	6) DISCREPANCY IN PLANS. 107.2.1.3 ADDITIONAL
	INFORMATION IS REQUIRED. PLEASE REVIEW SHEET A0.7 AND
	M2.1. SHEET A0.7 INDICATES A (1) HOUR FIRE RATING
	WHEREAS THE M2.1 SHOWS A (2) HR. FIRE RATING. SHAFTS
	LESS THAN 4 STORIES ONLY REQUIRE A 1 HOUR FIRE RATING,
	FBC-B 713.4.

	7) SEE SHEETS A0.5 FLOOR PLAN ENTRY DOOR 101 AND SHEET
	A8.3 DETAILS 5&6. SHEET A0.5 SHOWS A SINGLE ENTRY DOOR
	AND SIDE LIGHT. SHEET A8.3 SHOWS 2 DETAILS OF THE ENTRY
	DOOR, THE SIDE LIGHT DOESN?T APPEAR IN ANY DETAILS. THE
	OTHER ISSUE IS IN DETAIL 5 IT IS A SINGLE PAIN OF GLASS
	WITH PANIC HARDWARE, IN DETAIL # 6 THERE ARE (2) PANES
	OF GLASS AND NO PANIC HARDWARE. 107.2.1.3 DISCREPANCY
	IN PLANS AND FBC-B 1008.1.10 PANIC AND FIRE EXIT
	HARDWARE.

	8) SHEET A8.5 DETAIL # 11 SHOWS A PATIO GATE AND DETAIL
	# 5 A GUARDRAIL. SHEETS A0.3 AND A0.5 BOTH SHOW THE
	OUTDOOR PATIO BUT PLEASE NOTE THIS AREA IS THE PUBLIC
	RIGHT OF WAY. FBC-B 3202.1.3 AREAWAYS.
	AREAWAYS SHALL BE PROTECTED BY GRATES, GUARDS OR OTHER
	APPROVED MEANS.

	3202.2 ENCROACHMENTS ABOVE GRADE AND BELOW 8 FEET IN
	HEIGHT.
	ENCROACHMENTS INTO THE PUBLIC RIGHT-OF-WAY ABOVE GRADE
	AND BELOW 8 FEET (2438 MM) IN HEIGHT SHALL BE
	PROHIBITED EXCEPT AS PROVIDED FOR IN SECTIONS 3202.2.1
	THROUGH 3202.2.3. DOORS AND WINDOWS SHALL NOT OPEN OR
	PROJECT INTO THE PUBLIC RIGHT-OF-WAY.
	3202.2.1 STEPS.
	3202.2.2 ARCHITECTURAL FEATURES.
	3202.2.3 AWNINGS.

	9) 2014 FBC-B 1609.1.2 PROTECTION OF OPENINGS,
	1609.6.4.4.1 COMPONENTS & CLADDING. 61-41,003
	ADMINISTRATION AND DEPARTMENT RESPONSIBILITIES. (4)
	TESTING & EVALUATION OF PRODUCTS. FL. S. 553.842
	PRODUCT EVALUATION AND APPROVAL.
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS, ADMINISTRATIVE
	CODE 61G20-3.005, RULE 9N-3 NOV. 01/ 2010 (31)
	SUB-CATEGORY OF PRODUCTS OR CONSTRUCTION SYSTEMS THAT
	WILL REQUIRE PRODUCT APPROVALS:
	(31)(A) EXTERIOR DOORS ,MULLIONS & ROOF HATCHES.
	(B) WINDOWS & MULLIONS
	(C) PANEL WALLS: STOREFRONTS, CURTAIN WALLS, WALL
	LOUVERS, EFIS SYSTEMS,
	(D) ROOFING PRODUCTS AND ASSEMBLIES, ROOF TOP CURBS,
	ROOF TOP VENTILATORS & FANS
	(E) SHUTTERS
	(F) SKYLIGHTS
	(G) EXTERIOR COOLER, FREEZERS & PRE-ENGINEERED A/C
	STANDS

	10) FBC 107.3.4.1 PRODUCT APPROVALS. THOSE PRODUCTS
	WHICH ARE REGULATED BY THE DCA RULE 9N-03 SHALL BE
	REVIEWED AND APPROVED IN WRITING BY THE DESIGNER OF
	RECORD PRIOR TO SUBMITTAL FOR JURISDICTIONAL APPROVAL.
	FL 61G1-23.015 (2) THE ARCHITECT IS RESPONSIBLE FOR
	SUPERVISING AND REVIEWING ALL PROJECT DATA, REPORTS,
	SHOP DRAWINGS ETC..

	11) SHEET M103 SHOWS ROOF TOP FANS BUT THE DETAILS DO
	NOT PROVIDE ANCHORAGE OF THE CURB TO THE ROOF FRAMING
	NOR THE ROOFTOP FAN TO THE UNIT.
	2014 FBC-B 1604.4 ANALYSIS. LOAD EFFECTS ON STRUCTURAL
	MEMBERS AND THEIR CONNECTIONS SHALL BE DETERMINED BY
	METHODS OF STRUCTURAL ANALYSIS THAT TAKE INTO ACCOUNT
	EQUILIBRIUM, GENERAL STABILITY, GEOMETRIC COMPATIBILITY
	AND BOTH SHORT- AND LONG-TERM MATERIAL PROPERTIES.
	EVERY STRUCTURE SHALL BE DESIGNED TO RESIST THE
	OVERTURNING EFFECTS CAUSED BY THE LATERAL FORCES
	SPECIFIED IN THIS CHAPTER. SEE SECTION 1609 FOR WIND
	LOADS.
	2014 FBC-M- 301.15 WIND RESISTANCE. MECHANICAL
	EQUIPMENT, APPLIANCES AND SUPPORTS THAT ARE EXPOSED TO
	WIND SHALL BE DESIGNED AND INSTALLED TO RESIST THE WIND
	PRESSURES DETERMINED IN ACCORDANCE WITH THE FLORIDA
	BUILDING CODE, BUILDING.

	12) BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
	FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
	PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
	A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
	APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	13) WHEN RESUBMITTING PLANS PLEASE INDICATE THE
	REVISION & REMOVE ANY VOIDED SHEETS & REPLACE ANY PAGES
	AS NECESSARY, COLLATE AND STAPLE INTO SETS OF PLANS. A
	TRANSMITTAL LETTER LISTING THE ORIGINAL REVIEW COMMENT
	NUMBER, WITH A DESCRIPTION OF THE REVISION MADE,
	IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE THE
	CHANGES CAN BE FOUND WILL HELP TO EXPEDITE YOUR PERMIT.
	THANK YOU FOR YOUR ANTICIPATED COOPERATION.

	A THOROUGH REVIEW CANNOT BE MADE AT THIS TIME, AS A
	RESULT OF THE ADDITIONAL INFORMATION REQUESTED
	ADDITIONAL COMMENTS MAY APPEAR THAT WERE NOT PART OF
	THIS REVIEW.

	JAMES A. WITMER BN, PX, CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	CONSTRUCTION SERVICES DIVISION/ DEVELOPMENT SERVICES
	DEPARTMENT
	401 CLEMATIS ST.
	WEST PALM BEACH. FL 33402
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	E			ELECTRICAL
Rev No	2	Status	P	Date	2017-06-12			Cont ID
Sent By	jleahy			Date	2017-06-12	Time	08:29	Rev Time	0.00
Received By	jleahy			Date	2017-06-12	Time	08:29	Sent To

Notes

***NONE***

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2017-03-10			Cont ID
Sent By	jleahy			Date	2017-03-10	Time	10:08	Rev Time	0.00
Received By	jleahy			Date	2017-03-09	Time	16:52	Sent To

Notes

2017-03-10 10:50:30	PAGE E101
	A) LOAD CACLUATION PER ARTICLE 220 REQUIRED.
	B) FAULT CURRENT CALCULATION REQUIRED PER 110.24
	C) LABELING FOR FAULT CURRENT REQUIRED PER 100.24
	D) NEED THE GROUNDING DETAIL SHOWN ON DRAWING FOR THE
	SERVICE.
	E) RISER DIAGRAM FEEDER 200 TOO SMALL FOR 400A
	F) RISER DIAGRAM FEEDER 300 NOT SHOWN ON DRAWINGS
	G) TIME CLOCK SUBMIT CUT SHEET

	PAGE E201
	A) CIRCUITS AT THE BAR B19,21,23, A48,18,22 REQUIRE
	GFCI PROTECTION 210.8(B)(5)
	B) KITCHEN OUTLETS A29,34,53,58,59, B31,33,35,37
	REQUIRE GFCI PROTECTION 210.8(B)(2)

	PAGE E202
	A) ROOF NEEDS AN OUTLET WITHIN 25' OF THE EQUIPMENT AND
	GFCI PROTECTED 210.63, 210.8(B)(3)

	PAGE E301
	A) SUBMIT INTERIOR LIGHTING POWER ALLOWANCES PER FBC EC
	C405.5.2
	B) LIGHTING IN BAR AREA NOT CLEAR ON DRAWINGSS LINES
	ALL OVER THE AREA NOT CONNECTED TO ANYTHING.
	C) LIGHT FIXTURE TYPES TO BE LABLELED ON ALL FIXTURES
	ON DRAWING FOR REVIEW.
	D) ALL CIRCUITS ARE SHOWN AS TIME CLOCK NEED CIRCUIT
	NUMBERS ON PLANS FOR LIGHTING.

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	3	Status	P	Date	2017-06-28			Cont ID
Sent By	wjolin			Date	2017-06-28	Time	12:30	Rev Time	0.00
Received By	wjolin			Date	2017-06-28	Time	12:27	Sent To

Notes

***NONE***

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	2	Status	F	Date	2017-05-31			Cont ID
Sent By	wjolin			Date	2017-05-31	Time	10:31	Rev Time	0.00
Received By	wjolin			Date	2017-05-24	Time	15:18	Sent To

Notes

2017-05-24 12:15:28	218 CLEMATIS STREET
	PERMIT #17020623
	REVIEW COMMENTS - FIRE DEPARTMENT

	THE PRODUCT DATA FOR THE FIRE PIT INDICATES IT IS ONLY
	TO BE INSTALLED OUTDOORS. ADDITIONALLY THIS OFFICE DOES
	NOT SUPPORT THE USE OF INTERIOR OPEN FLLAME DEVICES.

	SHEET E301: NO EMERGENCY LIGHTING PROVIDED.

	NFPA 96 SECTION 14.1.5 WHERE A SOLID FUEL COOKING
	APPLIANCE ALLOWS EFFLUENT TO ESCAPE FROM THE APPLIANCE
	OPENING, THIS OPENING SHALL BE COVERED BY A HOOD AND AN
	EXHAUST SYSTEM THAT MEETS THE REQUIREMENTS OF SECTIONS
	14.3, 14.4, AND 14.6.14.7.1 SOLID FUEL COOKING
	APPLIANCES THAT PRODUCE GREASELADEN VAPORS SHALL BE
	PROTECTED BY LISTED FIRE-EXTINGUISHING EQUIPMENT. NO
	TYPE I EXHAUST HOOD WITH SUPPRESSION SYSTEM PROVIDED
	FOR WOOD FIRED PIZZA OVENS.

	SOLID COOKING OPERATIONS AND DESIGN SHALL COMPLY WITH
	NFPA 96. APPLIANCES WITH FIREBOXES OVER 5 FT3 THE WATER
	SOURCE SHALL BE A FIXED PIPE WATER SYSTEM WITH A HOSE
	OF ADEQUATE LENGTH TO REACH THE COMBUSTION AND COOKING
	CHAMBERS OF THE APPLIANCE. ALL OVEN ASH SHALL BE
	REMOVED FROM THE ASH COMPARTMENT AT LEAST ONCE PER DAY.
	THE ASH SHALL BE SPRAYED ADEQUATELY WITH WATER BEFORE
	REMOVAL TO EXTINGUISH ANY HOT ASH OR CINDERS AND TO
	CONTROL THE DUST WHEN THE ASH IS MOVED. SECTION
	14.9.3.8.1 A HEAVY METAL CONTAINER OR CART (MINIMUM 16
	GAUGE) WITH A COVER SHALL BE PROVIDED FOR THE REMOVAL
	OF ASH. THE ASH REMOVAL CONTAINER OR CART SHALL NOT
	EXCEED A MAXIMUM OF 20 GAL CAPACITY, SHALL BE ASSIGNED
	FOR THIS ONE PURPOSE, SHALL BE ABLE TO BE HANDLED
	EASILY BY ANY EMPLOYEE ASSIGNED THE TASK, AND SHALL
	PASS EASILY THROUGH ANY PASSAGEWAY TO THE OUTSIDE OF
	THE BUILDING. THE CONTAINER OR CART SHALL ALWAYS BE
	COVERED WHEN IT IS BEING MOVED THROUGH THE PREMISES.

	NO FIRE ALARM OR FIRE SPRINKLER SCOPE OF WORK PROVIDED.

	EXISTING EXIT DOORS: FOR ASSEMBLY OCCUPANCIES WITH AN
	OCCUPANT LOAD OF 100 OR MORE PERSONS (50 PERSONS PER
	THE FLORIDA BUILDING CODE), PANIC HARDWARE SHALL BE
	PROVIDED ON DOORS TO RELEASE THE LOCK/LATCH. NO OTHER
	LOCKS OR LATCHES ARE PERMITTED THAT WOULD NOT BE
	RELEASED BY THE PANIC HARDWARE. AS A SUBSTITUTE FOR
	PANIC HARDWARE, THE MAIN ENTRANCE IS PERMITTED TO HAVE
	AN INTERIOR KEYED DOOR LOCK (AND NO LATCH) WITH A
	READILY VISIBLE SIGN STATING THIS DOOR TO REMAIN
	UNLOCKED WHEN THE BUILDING IS OCCUPIED. SIGN LETTERS
	SHALL BE AT LEAST 1 INCH IN HEIGHT. KEYED LOCK TO BE
	EQUIPPED WITH AN ?OPEN/LOCKED? INDICATOR WINDOW (SUCH
	AS ADAMS RITE 4089 OR SIMILAR). A THUMB TURN STYLE LOCK
	IS NOT PERMITTED TO BE SUBSTITUTED FOR A KEYED LOCK.

	WESLEY JOLIN
	WEST PALM BEACH FIRE RESCUE
	FIRE & LIFE SAFETY PLAN REVIEW

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2017-03-01			Cont ID
Sent By	wjolin			Date	2017-03-01	Time	12:25	Rev Time	0.00
Received By	wjolin			Date	2017-02-21	Time	11:30	Sent To

Notes

2017-03-01 11:25:59	218 CLEMATIS STREET
	PERMIT #17020623
	REVIEW COMMENTS - FIRE DEPARTMENT

	ALL DEMOLITION WORK SHALL CONFORM TO THE REQUIREMENTS
	OF NFPA 241.

	FIRE PROTECTION SYSTEMS SHALL REMAIN ACTIVE DURING
	DEMOLITION AND RENOVATION ACTIVITIES. IN THE EVENT A
	FIRE PROTECTION SYSTEM IS OUT OF SERVICE FOR MORE THAN
	4-HOURS IN A 24-HOUR PERIOD, THE BUILDING SHALL BE
	PLACED UNDER A FIRE WATCH. ALL FIRE WATCH REQUESTS MUST
	BE APPROVED AND SUBMITTED IN WRITING TO THE OFFICE OF
	THE FIRE MARSHAL.

	PROVIDE AN EXTERIOR KEY SAFE TO ALLOW EMERGENCY
	RESPONDERS NON-FORCIBLE ENTRY INTO THE BUILDING DURING
	NON-BUSINESS HOURS. A KEY SAFE CAN BE ORDERED FROM
	WWW.KNOXBOX.COM.

	PROVIDE TACTILE SIGNAGE AT EXIT DOORS.

	INSUFFICIENT EXIT SIGNS PROVIDED TO IDENTIFY PRIMARY
	AND SECONDARY EXITS. NO EMERGENCY LIGHTING PROVIDED.

	PROVIDE MORE INFORMATION AND DETAILS FOR THE FIREPIT.
	SUBMIT PRODUCT DATA AND UL LISTING (OR EQUAL).

	PROVIDE UL LISTING (OR EQUAL) DATA FOR THE PIZZA OVENS.
	SUBMIT PRODUCT DATA FOR WOOD FIRED PIZZA OVENS
	INDICATING IF A SUPPRESSION SYSTEM IS REQUIRED FOR THIS
	APPLIANCE.

	INDICATE THE LOCATION AND QUANTITY OF WOOD FUEL TO BE
	STORED FOR THE PIZZA OVENS.

	SOLID COOKING OPERATIONS AND DESIGN SHALL COMPLY WITH
	NFPA 96. FOR EXAMPLE: PER SECTION 14.9.2.1. FUEL
	STORAGE SHALL NOT EXCEED A ONE-DAY SUPPLY WHERE STORAGE
	IS LOCATED IN THE SAME ROOM AS THE SOLID FUELED
	APPLIANCE, OR IN THE SAME ROOMS AS THE FUEL-LOADING OR
	CLEAN-OUT DOORS. SECTION14.9.3.7.3 APPLIANCES WITH
	FIREBOXES OVER 5 FT3 THE WATER SOURCE SHALL BE A FIXED
	PIPE WATER SYSTEM WITH A HOSE OF ADEQUATE LENGTH TO
	REACH THE COMBUSTION AND COOKING CHAMBERS OF THE
	APPLIANCE. ALL OVEN ASH SHALL BE REMOVED FROM THE ASH
	COMPARTMENT AT LEAST ONCE PER DAY. THE ASH SHALL BE
	SPRAYED ADEQUATELY WITH WATER BEFORE REMOVAL TO
	EXTINGUISH ANY HOT ASH OR CINDERS AND TO CONTROL THE
	DUST WHEN THE ASH IS MOVED. SECTION 14.9.3.8.1 A HEAVY
	METAL CONTAINER OR CART (MINIMUM 16 GAUGE) WITH A COVER
	SHALL BE PROVIDED FOR THE REMOVAL OF ASH. THE ASH
	REMOVAL CONTAINER OR CART SHALL NOT EXCEED A MAXIMUM OF
	20 GAL CAPACITY, SHALL BE ASSIGNED FOR THIS ONE
	PURPOSE, SHALL BE ABLE TO BE HANDLED EASILY BY ANY
	EMPLOYEE ASSIGNED THE TASK, AND SHALL PASS EASILY
	THROUGH ANY PASSAGEWAY TO THE OUTSIDE OF THE BUILDING.
	THE CONTAINER OR CART SHALL ALWAYS BE COVERED WHEN IT
	IS BEING MOVED THROUGH THE PREMISES.

	MEP PLANS ARE SIGNED; HOWEVER, THE SEAL IS A COPY OF
	THE SEAL.

	NO FIRE ALARM OR FIRE SPRINKLER SCOPE OF WORK PROVIDED.

	WESLEY JOLIN
	WEST PALM BEACH FIRE RESCUE
	FIRE & LIFE SAFETY PLAN REVIEW

Review Stop	G			GAS REVIEW
Rev No	2	Status	N	Date				Cont ID
Sent By				Date	2017-06-09	Time		Rev Time	0.00
Received By	gjohnson			Date	2017-06-09	Time	15:00	Sent To

Notes

2017-06-09 15:02:19

6/9/17 THE GAS HAS BEEN REMOVED FROM PLANS/GPJ

Review Stop	G			GAS REVIEW
Rev No	1	Status	F	Date	2017-03-17			Cont ID
Sent By	gjohnson			Date	2017-03-17	Time	09:16	Rev Time	0.00
Received By	gjohnson			Date	2017-03-17	Time	09:16	Sent To

Notes

2017-03-17 09:22:30	GAS COMMENTS:

	1. SHOW COMPLIANCE WITH FBC FUEL GAS 404.8.2 CONDUIT
	WITH BOTH ENDS TERMINATING INDOORS.
	WHERE THE CONDUIT ORIGINATES AND TERMINATES WITHIN THE
	SAME BUILDING, THE CONDUIT SHALL ORIGINATE AND
	TERMINATE IN AN ACCESSIBLE PORTION OF THE BUILDING AND
	SHALL NOT BE SEALED. THE CONDUIT SHALL EXTEND NOT LESS
	THAN 2 INCHES (51 MM) BEYOND THE POINT WHERE THE PIPE
	EMERGES FROM THE FLOOR.

	2, SHOW ROUTING FROM METER TO STEP DOWN REGULATOR NOT
	SHOWN ON SITE PLAN. PER WPB AMEND TO FBC 107,2,1

	3. TYPE OF GAS, (LP OR NATURAL).

	4. SUBMIT CALCULATIONS FOR COMBUSTION AIR PER THE
	FBC-2014 FUEL GAS CODE SEC. 304.

	5. INDICATE THE DELIVERY PRESSURE (PSI) PER FBC-2014
	FUEL GAS SEC. 402.2. IF NATURAL GAS SPECIFY .5 PSI OR 2
	PSI.

	6. SUBMIT A DETAIL SHOWING THE TYPE, LOCATION, SIZE AND
	TERMINATION OF THE GAS VENTS PER FBC-2014 FUEL GAS CODE
	SEC. 502 THRU 505.

	7. SUBMIT MANUFACTURER?S SPECIFICATION SHEETS FOR ALL
	GAS EQUIPMENT TO VERIFY COMPLIANCE WITH STANDARDS NFPA
	54, NFPA 58, AND FBC-2014 FUEL GAS SEC. 402.2


	1ST REVIEW

	GEORGE JOHNSON
	PLUMBING PLANS EXAMINER LL
	CITY OF WEST PALM BEACH
	DEVELOPMENT SERVICES
	BUILDING DIVISION
	561-805-6711
	[email protected]



	DUE TO THE DEFICIENCIES OF THIS PLAN A COMPLETE AND
	THOROUGH REVIEW CANNOT BE DONE AT THIS TIME. UPON
	RESUBMITTAL THERE MAYBE ADDITIONAL COMMENTS.

	WHEN RESUBMITTING PLANS, REMOVE AND REPLACE ANY PAGES
	AS NECESSARY. A NARRATIVE LISTING THE ORIGINAL REVIEW
	COMMENT NUMBER WITH A DESCRIPTION OF THE CHANGES MADE
	AND IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE
	THE CHANGE CAN BE FOUND WILL HELP EXPEDITE THE REVIEW.

Review Stop	I			INCOMING/PROCESSING
Rev No	3	Status	N	Date	2017-06-29			Cont ID
Sent By	lmarchan			Date	2017-06-29	Time	16:41	Rev Time	0.00
Received By	lmarchan			Date	2017-06-16	Time	13:23	Sent To

Notes

2017-06-20 13:23:57

C01

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2017-06-15			Cont ID
Sent By	cpuell			Date	2017-06-15	Time	07:54	Rev Time	0.00
Received By	cpuell			Date	2017-05-17	Time	14:37	Sent To

Notes

2017-05-18 14:37:41

C01

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date				Cont ID
Sent By				Date	2017-03-17	Time		Rev Time	0.00
Received By	lmarchan			Date	2017-02-14	Time	10:46	Sent To

Notes

2017-02-15 10:47:02

C01

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	4	Status	P	Date	2017-07-06			Cont ID
Sent By	jwitmer			Date	2017-07-06	Time	10:07	Rev Time	0.00
Received By	jwitmer			Date	2017-07-03	Time	15:54	Sent To

Notes

2017-07-06 10:07:17	PALM BEACH COUNTY IMPACT FEE OFFICE
	MU-2017-018590-0000
	RECEIPT NUMBER: 2017-0705-47
	FEES: $244.64
2017-07-03 15:54:41	GIVEN TO JWITMER

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	3	Status	F	Date	2017-06-27			Cont ID
Sent By	jwitmer			Date	2017-06-27	Time	06:42	Rev Time	0.00
Received By	jwitmer			Date	2017-06-27	Time	06:01	Sent To

Notes

***NONE***

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	2	Status	F	Date	2017-06-01			Cont ID
Sent By	jwitmer			Date	2017-06-01	Time	16:35	Rev Time	0.00
Received By	jwitmer			Date	2017-06-01	Time	11:29	Sent To

Notes

2017-06-01 16:34:56	IMPACT FEES
	BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
	FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
	PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
	A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
	APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	JAMES A. WITMER BN, PX, CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	1	Status	F	Date	2017-03-17			Cont ID
Sent By	jwitmer			Date	2017-03-17	Time	10:54	Rev Time	0.00
Received By	jwitmer			Date	2017-03-14	Time	08:07	Sent To

Notes

2017-03-17 10:54:29	IMPACT FEES
	BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
	FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
	PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
	A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
	APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	JAMES A. WITMER BN, PX, CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	3	Status	P	Date	2017-06-29			Cont ID
Sent By	ccole			Date	2017-06-29	Time	09:33	Rev Time	0.00
Received By	ccole			Date	2017-06-28	Time	08:59	Sent To

Notes

***NONE***

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2017-05-31			Cont ID
Sent By	ccole			Date	2017-05-31	Time	13:48	Rev Time	0.00
Received By	ccole			Date	2017-05-31	Time	10:40	Sent To

Notes

2017-05-31 14:41:38	2ND REVIEW FBC-2014 MECHANICAL
	PERMIT #17020623
	5/31/17

	RESULTS: DENIED.

	1) THE TWO GREASE EXHAUST DUCTS FOR THE PIZZA OVENS
	MUST BE RUN SEPARATELY BECAUSE THEY ARE SERVING
	SOLID-FUEL FIRED APPLIANCES- PLEASE SEE SECTION 506.3.5
	ITEM #4 AND SEPARATE THE DUCTS.

	2) ADVISORY: PLEASE REVIEW PAGE #3 OF THE SUBMITTED
	INSTALLATION INSTRUCTIONS FOR THE PIZZA OVENS AND
	SPECIFY ON THE PLANS WHICH OF THE THREE EXHAUST SYSTEMS
	WILL BE INSTALLED.

	3) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE
	VENTLESS RANGE AND DISHWASHER HOODS AND PROVIDE
	EQUIPMENT SCHEDULES ON THE PLANS.

	4) THE CAPTIVE-AIRE KITCHEN EXHAUST PLANS (SHEETS M102
	& M103) ARE NO LONGER APPLICABLE TO THE PROJECT. PLEASE
	EITHER REMOVE THE SHEETS FROM THE PLAN SETS, OR REVISE
	THEM TO SHOW THE NEW VENTLESS HOODS PLANS, DETAILS, AND
	EQUIPMENT SCHEDULES.

	5) M101: THE AIR BALANCE DIAGRAM NEEDS TO BE REVISED TO
	MATCH THE REVISED PLANS AND SYSTEMS. PLEASE NOTE THE
	FOLLOWING: A) EF02 IS INDICATED TO HAVE A CAPACITY OF
	1475 CFMS IN THE AIR BALANCE DIGRARM, BUT ONLY 470 CFMS
	IN THE FAN SCHEDULE. B) EF04 AND SF03 ARE STILL SHOWING
	IN THE DIAGRAM HOWEVER THEY HAVE BEEN REMOVED FROM THE
	PLANS.

	6) M101: PLEASE PLACE A NOTE TO INDICATE THE LOCATIONS
	OF THE AHU ACCESS PANELS AND PROVIDE DIMENSIONS-
	SECTION 306.1

	7) THE WIND LOAD ENGINEERING FOR INSTALLATION OF THE
	ROOFTOP EQUIPMENT IS INCOMPLETE: A) PROVIDE DETAILS FOR
	ANCHORING THE NEW CONDENSERS TO THE EXISTING STANDS. B)
	PROVIDE DETAILS FOR INSTALLATION OF THE GREASE DUCT
	SUPPORTS. C) SUBMIT THE NOA FOR THE NEW ROOF STAND WITH
	SHOP DRAWING APPORVAL STAMP BY THE EOR.

	CHRISTOPHER L. COLE
	MECHANICAL PLANS EXAMINER
	401 CLEMATIS STREET
	WEST PALM BEACH FL 33401
	561-805-6719
	[email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2017-02-23			Cont ID
Sent By	ccole			Date	2017-02-23	Time	11:42	Rev Time	0.00
Received By	ccole			Date	2017-02-23	Time	11:42	Sent To

Notes

2017-02-23 13:01:05	1ST REVIEW FBC-2014 MECHANICAL
	PERMIT #17020623
	2/23/17

	1) THE CITY OF WEST PALM BEACH BUILDING DIVISION
	REQUIRES SEPARATE PERMITS FOR KITCHEN EXHAUST HOODS,
	FIRE SUPPRESSION SYSTEMS, FIRE SPRINKLERS, AND WALK-IN
	COOLERS AND FREEZERS- PLACE A NOTE ON THE PLANS
	ACCORDINGLY. PLEASE NOTE THAT NO DETAILS OR
	SPECIFICATIONS FOR THE DISHWASHER HOOD HAVE BEEN
	PROVIDED.

	2) SHEET M201: THE MAKEUP AIR DUCT FOR THE KITCHEN
	HOODS IS PROHIBITED FROM BEING IN THE SAME RATED SHAFT
	ENCLOSURE WITH THE GREASE EXHAUST DUCT- SECTION
	506.3.11. OPTIONS- REMOVE THE MAKEUP AIR DUCT, OR
	INDICATE THE GREASE DUCT IS TO BE WRAPPED WITH APPROVED
	LISTED AND LABELED DUCT WRAP PER SECTION 506.3.11.2.

	3) ADVISORIES- KITCHEN AND EXHAUST HOODS:

	A) AN 18" CLEARANCE TO COMBUSTIBLES IS REQUIRED FOR THE
	GREASE EXHAUST DUCTS- SEE SECTIONS 506.3.6, 506.3.11,
	506.3.11.1, & 506.3.11.2. IF A DUCT WRAP IS TO BE
	INSTALLED, MANUFACTURER'S SPECIFICATIONS SHALL BE
	SUBMITTED PER SECTION 506.3.11.2, AND THE GREASE DUCT
	PENETRATIONS INTO AND OUT OF THE RATED SHAFTS SHALL BE
	PROTECTED WITH A THROUGH-PENETRATION FIRE-STOP SYSTEM
	CLASSIFIED IN ACCORDANCE WITH ASTM E 814 OR UL 1497.
	PLEASE NOTE THAT THERE IS NO REQUIREMENT FOR THE FIRE
	DAMPERS TO BE INSTALLED IN THE GREASE DUCTS AT THE
	SHAFT PENETRATIONS.

	B) PLEASE NOTE THAT THE TEMPERATURE DIFFERENTIAL
	BETWEEN MAKE-UP AIR FOR THE KITCHEN EXHAUST AND THE AIR
	IN THE CONDITIONED SPACE SHALL NOT EXCEED 10 DEGREES F
	PER SECTION 508.1.1. MEETING THIS COMPLIANCE MAY
	REQUIRE PRE-COOLING OF THE MAKE-UP AIR USING AN AC UNIT

	C) THE NOA'S FOR THE ROOFTOP FANS MUST BE SUBMITTED
	WITH SHOP DRAWING APPROVAL STAMPS AND SIGNATURES BY THE
	ENGIEER OF RECORD. THE EOR MUST ALSO CIRCLE, HIGHLIGHT,
	OR OTHERWISE MARK ALL APPLICABLE INSTALLATION NOTES,
	DETAILS, DESIGN PRESSURES, AND ANCHORING METHODS ON THE
	DOCUMENTS.

	4) SHEETS M201 & A0.7: THE PLANS ARE CONFLICTING
	CONCERNING THE HOURLY FIRE-RATINGS OF THE SHAFTS.

	5) SHEET M201: INDICATE THE REQUIRED CLEARANCE DISTANCE
	MEASUREMENTS FOR THE O/A INTAKE LOCATIONS AS REQUIRED
	BY SECTION 401.4.

	6) M201: SHOW THE TERMINATION LOCATION OF THE
	DISHWASHER HOOD EXHAUST DUCT.

	7) M201: REFER TO SECTION 304 FLORIDA FUEL GAS CODE AND
	PROVIDE COMBUSTION AIR CALCULATIONS FOR THE PIZZA
	OVENS, THE KITCHEN COOKING APPLIANCES, AND THE GAS
	WATER HEATER.

	8) PROVIDE AN EQUIPMENT SCHEDULE FOR THE GAS WATER
	HEATER AND MODIFY THE DETAIL ON M101 TO INDICATE THE
	TYPE AND SIZE OF GAS VENT AND TOTAL RUN FROM THE WH TO
	THE TERMINATION CAP.

	9) M201: INDICATE HOW ACCESS FOR MAINTENANCE AND
	REPLACEMENT OF THE AIR HANDLERS IN THE SOFFIT WILL BE
	PROVIDED- SEE SECTION 306.1.

	10) M201: PROVIDE CONDENSATE DISPOSAL PLANS FOR THE
	AHU'S- SECTION 307.

	11) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE PIZZA
	OVENS AND THEIR ASSOCIATED EXHAUST HOODS AND VENTS. SEE
	COMMENT #2B ABOVE- FIRE DAMPERS MAY NOT BE REQUIRED FOR
	THE EXHAUST DUCT PENETRATING THE SHAFT ENCLOSURE.

	12) WIND LOAD ENGINEERING IS REQUIRED FOR INSTALLATION
	OF ALL THE ROOF TOP MECHANICAL EQUIPMENT PER SECTION
	301.15. PLEASE PROVIDE COMPLETE DETAILS FOR ANCHORING
	THE UNITS TO THE ROOF STRUCTURE.

	13) PLEASE REVIEW CHAPTER 10 OF THE FBC-14 EXISTING
	BUILDING CODE- THE PROPOSED PROJECT IS A CHANGE OF
	OCCUPANCY AND SHOULD BE NOTED AS SUCH UNDER THE
	BUILDING CODE DATA ON SHEET A0.1.

	14) PLEASE REVIEW SECTION C101.4.4 AND SECTION C401.2
	FBC-14 ENERGY CONSERVATION AND PROVIDE DOCUMENTATION OF
	ENERGY CONSERVATION COMPLIANCE. THE SUBMITTED ENERGY
	FORM C402-2014 IS FOR RENOVATED BUILDINGS, AND CANNOT
	BE USED FOR BUILDINGS UNDERGOING A CHANGE OF OCCUPANCY.

	CHRISTOPHER L. COLE
	MECHANICAL PLANS EXAMINER
	561-805-6719
	[email protected]

Review Stop	P			PLUMBING
Rev No	2	Status	P	Date	2017-06-09			Cont ID
Sent By	gjohnson			Date	2017-06-09	Time	15:00	Rev Time	0.00
Received By	gjohnson			Date	2017-06-09	Time	15:00	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2017-03-17			Cont ID
Sent By	gjohnson			Date	2017-03-17	Time	08:34	Rev Time	0.00
Received By	gjohnson			Date	2017-03-17	Time	08:33	Sent To

Notes

2017-03-17 09:12:43	1ST REVIEW

	GEORGE JOHNSON
	PLUMBING PLANS EXAMINER LL
	CITY OF WEST PALM BEACH
	DEVELOPMENT SERVICES
	BUILDING DIVISION
	561-805-6711
	[email protected]

	PLUMBING COMMENTS:

	1. DOOR ON ACCESSIBLE TOILET STALLS SHALLL NOT SWING
	INTO THE CLEAR FLOOR SPACE OR CLEARANCE REQUIRED FOR
	ANY FIXTURE. DOORS SHALL BE PERMITTED TO SWING INTO THE
	REQUIRED TURNING SPACE. PER FBC ACC 603.2.3

	2. GRAB BARS SHALL BE INSTALLED IN A HORIZONTAL
	POSITION, 33 INCHES (840 MM) MINIMUM AND 36 INCHES (915
	MM) MAXIMUM ABOVE THE FINISH FLOOR MEASURED TO THE TOP
	OF THE GRIPPING SURFACE, PER FBC ACC 609.4

	3. TOILET PAPER DISPENSERS SHALL COMPLY WITH 309.4 AND
	SHALL BE 7 INCHES (180 MM) MINIMUM AND 9 INCHES (230
	MM) MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO
	THE CENTERLINE OF THE DISPENSER. THE OUTLET OF THE
	DISPENSER SHALL BE 15 INCHES (380 MM) MINIMUM AND 48
	INCHES (1220 MM) MAXIMUM ABOVE THE FINISH FLOOR AND
	SHALL NOT BE LOCATED BEHIND GRAB BARS. DISPENSERS SHALL
	NOT BE OF A TYPE THAT CONTROLS DELIVERY OR THAT DOES
	NOT ALLOW CONTINUOUS PAPER FLOW. PER FBC ACC 604.7

	4. DRINKING FOUNTAINS SHALL COMPLY WITH 307 AND 602.
	PER FBC ACC 602.1

	5. ALL FIXTURE FLOWING THROUGH GREASE INTERCEPTOR SHALL
	BE INCLUDED ON THE SIZING CALCULATION THE FIXTURES THAT
	ARE MISSING FROM CALCULATIONS ARE # 4 MOP SINK, #6.1
	SINK, #6.2 SINK, #7 PRE RINSE SINK, #8 DISHWASHER , #12
	SINK , #32.A TROUGH DRAIN. PER FBC PL 1003.3.1

	6. FIXTURES IN THE BAR AREA SHALL NOT BE ON THE GREASE
	SYSTEM. PER FBC PL 1003.2

	7. THE THREE COMP SINK SHALL BE INDIRECTLY WASTED. PER
	FBC PL 802.1

	8. SHT. P101 DETAIL B5 THE FIRST NOTE REQUIRING
	TEMPERED WATER IS WRONG THE TEMPERATURE FOR TEMPERED
	WATER SHAL BE BETWEEN 85?F (29?C) AND 110?F (43?C). PER
	FBC PL 202

	9. SHOW TEMPERATURE LIMITING DEVICE ON WATER RISER
	DIAGRAM TO SHOW COMPLIANCE WITH FBC PL 416.5

	10. SHOW COMPLIANCE WITH FBC PL 604.9 WATER HAMMER.
	THE FLOW VELOCITY OF THE WATER DISTRIBUTION SYSTEM
	SHALL BE CONTROLLED TO REDUCE THE POSSIBILITY OF WATER
	HAMMER. A WATER-HAMMER ARRESTOR SHALL BE INSTALLED
	WHERE QUICK-CLOSING VALVES ARE UTILIZED. WATER-HAMMER
	ARRESTORS SHALL BE INSTALLED IN ACCORDANCE WITH THE
	MANUFACTURER?S INSTRUCTIONS. WATER-HAMMER ARRESTORS
	SHALL CONFORM TO ASSE 1010.



	DUE TO THE DEFICIENCIES OF THIS PLAN A COMPLETE AND
	THOROUGH REVIEW CANNOT BE DONE AT THIS TIME. UPON
	RESUBMITTAL THERE MAYBE ADDITIONAL COMMENTS.

	WHEN RESUBMITTING PLANS, REMOVE AND REPLACE ANY PAGES
	AS NECESSARY. A NARRATIVE LISTING THE ORIGINAL REVIEW
	COMMENT NUMBER WITH A DESCRIPTION OF THE CHANGES MADE
	AND IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE
	THE CHANGE CAN BE FOUND WILL HELP EXPEDITE THE REVIEW.

Review Stop	Z			ZONING
Rev No	3	Status	P	Date	2017-06-29			Cont ID
Sent By				Date	2017-06-29	Time		Rev Time	0.00
Received By	kmartin			Date	2017-06-29	Time	15:34	Sent To	I

Notes

2017-06-29 15:35:02	BASED ON WASTE PRODUCTION CALCULATIONS, THE BUILDING
	OWNER WILL BE CONTACTED FOR NECESSARY IMPROVEMENTS TO
	THE WASTE RECEPTACLE AREA.

Review Stop	Z			ZONING
Rev No	2	Status	F	Date	2017-06-14			Cont ID
Sent By				Date	2017-06-14	Time		Rev Time	0.00
Received By	kmartin			Date	2017-06-14	Time	15:10	Sent To

Notes

2017-06-14 15:17:35	PREVIOUS COMMENTS HAVE NOT BEEN ADDRESSED.

	1. THIS PERMIT DOES NOT INCLUDE THE AREA IDENTIFIED AS
	-OUTDOOR PATIO 100- ON SHEET A 0.5. A SEPARATE PROCESS,
	SIDEWALK CAFE IS REQUIRED. BE ADVISED THAT OUTDOOR
	FURNITURE SHALL NOT BE FIXED PERMANENTLY. ALL OUTDOOR
	FURNITURE SHALL BE STORED AFTER OPERATION HOURS.

	2. DUMPSTER SHALL BE PROPERLY SCREENED AND LANDSCAPED
	MEETING THE REQUIREMENTS OF SECTION 94-315.

	FOR MORE INFORMATION, PLEASE CONTACT KEVIN MARTIN,
	URBAN DESIGN PLANNER, AT [email protected].

Review Stop	Z			ZONING
Rev No	1	Status	F	Date	2017-03-09			Cont ID
Sent By				Date	2017-03-09	Time		Rev Time	0.00
Received By	kmartin			Date	2017-03-08	Time	16:51	Sent To

Notes

2017-03-09 16:07:38	1. THIS PERMIT DOES NOT INCLUDE THE AREA IDENTIFIED AS
	-OUTDOOR PATIO 100- ON SHEET A 0.5. A SEPARATE PROCESS,
	SIDEWALK CAFE IS REQUIRED. BE ADVISED THAT OUTDOOR
	FURNITURE SHALL NOT BE FIXED PERMANENTLY. ALL OUTDOOR
	FURNITURE SHALL BE STORED AFTER OPERATION HOURS.

	2. SHOW DUMPSTER ON THE SITE PLAN, ENSURE THAT IT IS
	PROPERLY SCREENED AND LANDSCAPED MEETING THE
	REQUIREMENTS OF SECTION 94-444.

	FOR MORE INFORMATION, PLEASE CONTACT KEVIN MARTIN,
	URBAN DESIGN PLANNER, AT [email protected].