City of West Palm Beach eGovPlus

Plan Review Details - Permit 15060791

Plan Review Stops For Permit 15060791

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	3	Status	P	Date	2015-10-19			Cont ID
Sent By	jwitmer			Date	2015-10-19	Time	15:55	Rev Time	0.00
Received By	jwitmer			Date	2015-10-19	Time		Sent To

Notes

***NONE***

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2015-09-21		Cont ID
Sent By	jwitmer			Date	2015-09-21	Time	Rev Time	0.00
Received By	jwitmer			Date	2015-09-21	Time	Sent To

Notes

2015-09-21 14:38:47	BUILDING PLAN REVIEW
	W. P. B. PERMIT: 15060791
	ADD: 333 CLEMATIS ST.
	CONTRACTOR: HORMAK CONSTRUCTION
	TEL: (561)790-6863
	E-MAIL: [email protected]

	2010 FLORIDA BUILDING CODE W
	* 2010 WEST PALM BEACH AMENDMENTS TO THE FLORIDA
	BUILDING CODE, CHAPTER 1, ADMINISTRATION, 2010 EDITION
	2012 FBC SUPPLEMENTS ADOPTED APRIL 25/2013.

	2010 EXISTING BUILDING CODE LEVEL II 701.3
	COMPLIANCE. ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS,
	SYSTEMS, AND SPACES SHALL COMPLY WITH THE REQUIREMENTS
	OF THE FLORIDA BUILDING CODE, BUILDING.

	2ND REVIEW
	DATE: MON. SEPT. 21/2015
	ACTION: DENIED

	1A) COMPLIED. WILL NEED TO GET A CBC OR CGC ONBOARD FOR
	WORK BEYOND THE SCOPE OF YOUR LICENSE. FL S.S. 489.113.

	1B)VALUE IS STILL LOW AT $20,000.00. THE SUMMITED
	CONTRACT VALUE IS $23,500.00 AND THERE IS NO LINE ITEM
	FOR THE NEW STOREFRONT DOOR AND WALL SYSTEM.
	1ST REVIEW COMMENT. FOR THE WHOLE PROJECT THE VALUE OF
	$3,000.00 IS CONSIDERABLY LOW. 108.3* BUILDING PERMIT
	VALUATION.

	2) COMPLIED. SHEET A-1. THE RESTROOM DOORWAY NEXT TO
	THE REAR EXIT BLOCKS THE REAR EXIT, WILL NEED TO SWING
	INTO THE RESTROOM, SHOW COMPLIANCE WITH SECTION 2010
	FBC-B 1008.1.9.11 DURING ITS SWING, ANY DOOR IN A MEANS
	OF EGRESS SHALL LEAVE UNOBSTRUCTED AT LEAST ONE HALF OF
	THE REQUIRED WIDTH OF AN CORRIDOR, PASSAGEWAY OR
	LANDING, NOR PROJECT MORE THAN 7 INCHES INTO THE
	REQUIRED WIDTH OF CORRIDOR OR PASSAGEWAY.

	3) SEMI- COMPLIED. SHEET A-2 INDICATES THE WIND DESIGN
	CRITERIA. NOTE THE DESIGNER OF RECORD HAS INDICATED
	THAT THE EXPOSURE FOR THIS LOCATION IS A EXPOSURE D.
	THIS IS MORE RESTRICTIVE BUT IF THE DESIGNER OF ECORD
	WISHES TO DESIGN TO THE MORE RESTRICTIVE D EXPOSURE
	THEN THE PRESSURES ALSO WILL NEED TO MEET THE
	PRESSURES.

	THE PRESSURES FOR ROOF ZONES 1, 2 & 3 ALL INDICATE A
	PRESSURE OF 23.99 FOR 20 SQ. FT. THE FASTENING FOR
	ROOFS IS TAKEN AT 10 SQ. FT. FOR FASTENERS. THE DESIGN
	LIST THE VULT WIND SPEED OF 170 MPH. THE PRESSURES DO
	NOT INDICATE IF THEY ARE VULT OR VASD? THE ROOF
	PRESSURES IN VASD FOR A EXPOSURE D ARE FOR ZONE 1 ARE
	-50.4, ZONE 2 -108.4 & FOR ZONE 3 -127.3 @ 25 FT. MEAN
	ROOF HEIGHT.

	THE WINDOW PRESSURES WILL ALSO NEED TO INDICATE IF THEY
	ARE VULT OR VASD.

	COMMENT FROM THE 1ST REVIEW
	SHEET A-1 SHOWS A NEW GLASS STOREFRONT WINDOWS AND SET
	OF DOUBLE DOORS. PLEASE PROVIDE THE WIND DESIGN
	CRITERIA.
	. WIND DESIGN CRITERIA
	2010 FBC-B 1609.1.1 DETERMINATION OF WIND DESIGN-
	CHAPTER 6 OF ASCE 7-10.
	1609.3 BASIC WIND SPEED FIGURE 1609.A-C
	1609.3 WIND SPEED CONVERSION


	3.1) THE BASIC WIND SPEED, VU, SHALL BE DETERMINED IN
	ACCORDANCE WITH 1609.3.1 & ASCE 7-10

	3.2) AN IMPORTANCE FACTOR, FIGURE 1609 A-C, ASCE 7-10.

	3.3) AN EXPOSURE CATEGORY SHALL BE DETERMINED IN
	ACCORDANCE WITH 1609.4 & ASCE 7-10

	3.4) A HEIGHT AND EXPOSURE ADJUSTMENT COEFFICIENT, *
	SHALL BE DETERMINED FROM TABLE 1609.7.2. ASCE 7-10.

	3.5) COMPONENTS & CLADDING PRESSURES POSITIVE &
	NEGATIVE TABLE 1609.2(2).

	4) 2ND REQUEST, UNTIL PRESSURES ARE INDICATED IN EITHER
	VULT OR VASD THE PRODUCT APPROVALS CAN NOT BE REVIEWED.
	COMPONENTS & CLADDING/ 2010 FBC-B 1609.1.2 PROTECTION
	OF OPENINGS, 1609.6.4.4.1 COMPONENTS & CLADDING
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS RULE 9N-3 NOV.
	01/ 2010 (31) SUB-CATEGORY OF PRODUCTS OR CONSTRUCTION
	SYSTEMS THAT WILL REQUIRE PRODUCT APPROVALS:
	(31)(A) EXTERIOR DOORS.
	(B) WINDOWS
	(C) STOREFRONTS, CURTAIN WALLS, WALL LOUVERS, EFIS
	SYSTEMS
	(D) ROOFING PRODUCTS AND ASSEMBLIES
	(G) PRE-ENGINEERED A/C STANDS

	5) FBC 107.3.4.1 PRODUCT APPROVALS. THOSE PRODUCTS
	WHICH ARE REGULATED BY THE DCA RULE 9N-03 SHALL BE
	REVIEWED AND APPROVED IN WRITING BY THE DESIGNER OF
	RECORD PRIOR TO SUBMITTAL FOR JURISDICTIONAL APPROVAL.
	FL 61G1-23.015 (2) THE ARCHITECT IS RESPONSIBLE FOR
	SUPERVISING AND REVIEWING ALL PROJECT DATA, REPORTS,
	SHOP DRAWINGS ETC..

	6) 2ND REQUEST. PLEASE PROVIDE ENERGY CALCULATIONS FOR
	THE NEW ADDITION. PROVIDE COMPLIANCE FOR THE SHGC OF
	THE GLAZING COMPLY WITH FBC-ENERGY TABLE 502.1.1.1(1)
	OR TABLE 502.1.1.1(2).

	7) 2ND REQUEST. DEALS WITH THE ELEVATED PEDICURE
	STATIONS AND THE RAISED PLATFORM BY TENANT. EITHER THE
	RAISED PLATFORM IS PART OF THE PERMIT AND THE WORK
	SHOWN OR IT IS NOT AND THE PEDICURE STATIONS ARE NOT
	SHOWN SINCE THEY WOULD NO LONGER BE IN THE SCOPE OF
	WORK.

	107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE OF SUFFICIENT CLARITY
	TO INDICATE THE LOCATION, NATURE AND EXTENT OF THE WORK
	PROPOSED AND SHOW IN DETAIL THAT IT WILL CONFORM TO THE
	PROVISIONS OF THIS CODE AND RELEVANT LAWS, ORDINANCES,
	RULES AND REGULATIONS, AS DETERMINED BY THE BUILDING
	OFFICIAL. SUCH DRAWINGS AND SPECIFICATIONS SHALL
	CONTAIN INFORMATION, IN THE FORM OF NOTES OR OTHERWISE,
	AS TO THE QUALITY OF MATERIALS, WHERE QUALITY IS
	ESSENTIAL TO CONFORMITY WITH THE TECHNICAL CODES. SUCH
	INFORMATION SHALL BE SPECIFIC, AND THE TECHNICAL CODES
	SHALL NOT BE CITED AS A WHOLE OR IN PART, NOR SHALL THE
	TERM "LEGAL" OR ITS EQUIVALENT BE USED AS A SUBSTITUTE
	FOR SPECIFIC INFORMATION.

	AS FAR AS THE ACCESSIBLE PEDICURE STATION WITH A
	PORTABLE WASH TUB FOR SERVICE, IT WILL NEED TO SHOW A
	EQUIVALENCY TOO, 2010 FBC-ACCESSIBILITY CODE 103
	EQUIVALENT FACILITATION.


	COMMENT FROM THE 1ST REVIEW. SHEET A-1 SHOWS ELEVATED
	PEDICURE STATIONS AND A DETAIL 1 OF SHEET A-2. PLEASE
	SHOW COMPLIANCE WITH FBC-ACCESSIBILITY, VERTICAL
	ACCESSIBILITY TO PEDICURE STATIONS. 201.1.1.

	8) 2ND REQUEST, ADDITIONAL SQUARE FOOTAGE ADDED. BEFORE
	A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT FEES MUST
	BE PAID TO PALM BEACH COUNTY. THE ACTUAL PERMIT SET OF
	PLANS MUST BE STAMPED BY THAT OFFICE, AND A COPY OF THE
	PAID RECEIPT ATTACHED TO THE PERMIT APPLICATION. PLEASE
	CALL (561)233-5025 FOR MORE INFORMATION.

	9) WHEN RESUBMITTING PLANS PLEASE INDICATE THE REVISION
	& REMOVE ANY VOIDED SHEETS & REPLACE ANY PAGES AS
	NECESSARY. A TRANSMITTAL LETTER LISTING THE ORIGINAL
	REVIEW COMMENT NUMBER, WITH A DESCRIPTION OF THE
	REVISION MADE, IDENTIFYING THE SHEET OR SPECIFICATION
	PAGE WHERE THE CHANGES CAN BE FOUND WILL HELP TO
	EXPEDITE YOUR PERMIT. THANK YOU FOR YOUR ANTICIPATED
	COOPERATION.

	JAMES A. WITMER CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2015-06-22			Cont ID
Sent By	jwitmer			Date	2015-06-22	Time	06:28	Rev Time	0.00
Received By	jwitmer			Date	2015-06-22	Time	05:44	Sent To

Notes

2015-06-22 06:12:25
	BUILDING PLAN REVIEW
	W. P. B. PERMIT: 15060791
	ADD: 333 CLEMATIS ST.
	CONTRACTOR: RANDYS PLUMBING
	TEL: (561)242-9627
	E-MAIL:

	2010 FLORIDA BUILDING CODE W
	* 2010 WEST PALM BEACH AMENDMENTS TO THE FLORIDA
	BUILDING CODE, CHAPTER 1, ADMINISTRATION, 2010 EDITION
	2012 FBC SUPPLEMENTS ADOPTED APRIL 25/2013.

	2010 EXISTING BUILDING CODE LEVEL II 701.3
	COMPLIANCE. ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS,
	SYSTEMS, AND SPACES SHALL COMPLY WITH THE REQUIREMENTS
	OF THE FLORIDA BUILDING CODE, BUILDING.

	1ST REVIEW
	DATE: MON. JUNE 22/2015
	ACTION: DENIED

	1A) WILL NEED TO GET A CBC OR CGC ONBOARD FOR WORK
	BEYOND THE SCOPE OF YOUR LICENSE. FL S.S. 489.113.

	1B) FOR THE WHOLE PROJECT THE VALUE OF $3,000.00 IS
	CONSIDERABLY LOW. 108.3* BUILDING PERMIT VALUATION.

	2) SHEET A-1. THE RESTROOM DOORWAY NEXT TO THE REAR
	EXIT BLOCKS THE REAR EXIT, WILL NEED TO SWING INTO THE
	RESTROOM, SHOW COMPLIANCE WITH SECTION 2010 FBC-B
	1008.1.9.11 DURING ITS SWING, ANY DOOR IN A MEANS OF
	EGRESS SHALL LEAVE UNOBSTRUCTED AT LEAST ONE HALF OF
	THE REQUIRED WIDTH OF AN CORRIDOR, PASSAGEWAY OR
	LANDING, NOR PROJECT MORE THAN 7 INCHES INTO THE
	REQUIRED WIDTH OF CORRIDOR OR PASSAGEWAY.

	3) SHEET A-1 SHOWS A NEW GLASS STOREFRONT WINDOWS AND
	SET OF DOUBLE DOORS. PLEASE PROVIDE THE WIND DESIGN
	CRITERIA.

	WIND DESIGN CRITERIA
	2010 FBC-B 1609.1.1 DETERMINATION OF WIND DESIGN-
	CHAPTER 6 OF ASCE 7-10.
	1609.3 BASIC WIND SPEED FIGURE 1609.A-C
	1609.3 WIND SPEED CONVERSION


	3.1) THE BASIC WIND SPEED, VU, SHALL BE DETERMINED IN
	ACCORDANCE WITH 1609.3.1 & ASCE 7-10

	3.2) AN IMPORTANCE FACTOR, FIGURE 1609 A-C, ASCE 7-10.

	3.3) AN EXPOSURE CATEGORY SHALL BE DETERMINED IN
	ACCORDANCE WITH 1609.4 & ASCE 7-10

	3.4) A HEIGHT AND EXPOSURE ADJUSTMENT COEFFICIENT, *
	SHALL BE DETERMINED FROM TABLE 1609.7.2. ASCE 7-10.

	3.5) COMPONENTS & CLADDING PRESSURES POSITIVE &
	NEGATIVE TABLE 1609.2(2).

	4) COMPONENTS & CLADDING/ 2010 FBC-B 1609.1.2
	PROTECTION OF OPENINGS, 1609.6.4.4.1 COMPONENTS &
	CLADDING
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS RULE 9N-3 NOV.
	01/ 2010 (31) SUB-CATEGORY OF PRODUCTS OR CONSTRUCTION
	SYSTEMS THAT WILL REQUIRE PRODUCT APPROVALS:
	(31)(A) EXTERIOR DOORS.
	(B) WINDOWS
	(C) PANEL WALLS: STOREFRONTS, CURTAIN WALLS, WALL
	LOUVERS, EFIS SYSTEMS,
	(D) ROOFING PRODUCTS AND ASSEMBLIES
	(E) SHUTTERS
	(F) SKYLIGHTS
	(G) EXTERIOR COOLER, FREEZERS & PRE-ENGINEERED A/C
	STANDS

	5) FBC 107.3.4.1 PRODUCT APPROVALS. THOSE PRODUCTS
	WHICH ARE REGULATED BY THE DCA RULE 9N-03 SHALL BE
	REVIEWED AND APPROVED IN WRITING BY THE DESIGNER OF
	RECORD PRIOR TO SUBMITTAL FOR JURISDICTIONAL APPROVAL.
	FL 61G1-23.015 (2) THE ARCHITECT IS RESPONSIBLE FOR
	SUPERVISING AND REVIEWING ALL PROJECT DATA, REPORTS,
	SHOP DRAWINGS ETC..

	6) PLEASE PROVIDE ENERGY CALCULATIONS FOR THE NEW
	ADDITION. PROVIDE COMPLIANCE FOR THE SHGC OF THE
	GLAZING COMPLY WITH FBC-ENERGY TABLE 502.1.1.1(1) OR
	TABLE 502.1.1.1(2).

	7) SHEET A-1 SHOWS ELEVATED PEDICURE STATIONS AND A
	DETAIL 1 OF SHEET A-2. PLEASE SHOW COMPLIANCE WITH
	FBC-ACCESSIBILITY, VERTICAL ACCESSIBILITY TO PEDICURE
	STATIONS. 201.1.1.

	8) BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
	FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
	PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
	A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
	APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
	INFORMATION.

	9) WHEN RESUBMITTING PLANS PLEASE INDICATE THE REVISION
	& REMOVE ANY VOIDED SHEETS & REPLACE ANY PAGES AS
	NECESSARY. A TRANSMITTAL LETTER LISTING THE ORIGINAL
	REVIEW COMMENT NUMBER, WITH A DESCRIPTION OF THE
	REVISION MADE, IDENTIFYING THE SHEET OR SPECIFICATION
	PAGE WHERE THE CHANGES CAN BE FOUND WILL HELP TO
	EXPEDITE YOUR PERMIT. THANK YOU FOR YOUR ANTICIPATED
	COOPERATION.

	JAMES A. WITMER CBO
	SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
	TEL: 561-805-6715
	FAX: 561-805-6676
	E-MAIL: [email protected]

Review Stop	E			ELECTRICAL
Rev No	4	Status	P	Date	2015-11-30			Cont ID
Sent By	albarran			Date	2015-11-30	Time	15:37	Rev Time	0.00
Received By	albarran			Date	2015-11-30	Time	14:00	Sent To	I

Notes

2015-11-30 15:45:30	PER A TELEPHONE CONVERSATION WITH DEVEREN PETERKIN, WE
	AGREED THAT THERE IS A MISSING EMERGENCY LIGHT IN THE
	ELECTRICAL ROOM AND THE MISSING SIGN OUTLETS FOR THE
	REAR DOORS. SINCE ALL OTHER TRADES WERE APPROVED, I
	TOLD MR. PETERKIN THAT AS LONG AS WE AGREED TO GET
	THESE ITEMS DONE, I WOULD APPROVE MY REVIEW WITH THE
	EXCEPTION/PROVISO THAT THESE BE DONE FOR INSPECTION.

Review Stop	E			ELECTRICAL
Rev No	3	Status	F	Date	2015-10-28			Cont ID
Sent By	albarran			Date	2015-10-28	Time	12:37	Rev Time	0.00
Received By	albarran			Date	2015-10-28	Time	09:37	Sent To	I

Notes

2015-10-28 14:01:24	THE FAILURE TO PROVIDE A NARRATIVE OF THE CORRECTIONS
	AS REQUIRED PROMPTED FOR A COMPLETE REVIEW OF THE
	PLANS. THIS REVIEW PROVED THAT THE PREVIOUS COMMENTS
	WERE NOT FULLY ADDRESSED. BELOW ARE THE RESULTS OF THE
	THIRD REVIEW
	THE PLANS FOR THE ABOVE MENTIONED PERMIT APPLICATION
	HAVE BEEN REVIEWED FOR COMPLIANCE WITH THE 2008 EDITION
	OF THE NEC, (NATIONAL ELECTRICAL CODE); 2010 EDITION OF
	THE FBC, (FLORIDA BUILDING CODE) AS APPLICABLE AND
	BELOW ARE THE DEFICIENCIES NOTED.
	1. FOR SAFE EMERGENCY EGRESS, AN EMERGENCY LIGHT SHALL
	BE INSTALLED IN THE ELECTRICAL ROOM. AN ADDITIONAL
	EMERGENCY LIGHT SHALL BE INSTALLED IN THE HAIR WASH
	AREA, AND ANY OTHER AREA AS REQUIRED BY CODE.
	2. PER NFPA 101 SECTION 7.10.1.5.1 ALL EXITS SHALL BE
	MARKED WITH APPROVED READILY VISIBLE SIGNS. THE WAY
	TOWARDS THE EXITS, IF NOT READILY APPARENT SHALL BE
	MARKED AS WELL.
	3. NEC 1101.26(D) REQUIRES THAT PROPER ILLUMINATION BE
	PROVIDED FOR ALL WORKING SPACES ABOUT ELECTRICAL
	PANELS. THE AREA IN FRONT OF ELECTRICAL PANEL ?A? IS
	LACKING SAFE WORKING ILLUMINATION.
	4. FBC-ENERGY CONSERVATION SECTION 502.3.8 REQUIRES
	THAT ALL RECESSED LIGHTING INSTALLED IN THE BUILDING
	ENVELOPE SHALL BE IC PROTECTED AND AIR-TIGHT RATED &
	SEALED TO PREVENT AIR LEAKAGE BETWEEN THE CONDITIONED
	AND UNCONDITIONED SPACE.
	5. NEC 422.52 REQUIRES THAT THE ELECTRIC WATER COOLER
	BE CONNECTED TO A GFCI PROTECTED CIRCUIT.
	6. NEC 600.5 REQUIRES THAT EVERY COMMERCIAL OCCUPANCY
	BE PROVIDED WITH A DEDICATED 20 AMP CIRCUIT FOR SIGN OR
	OUTLINE LIGHTING AT EACH PEDESTRIAN ENTRANCE.
	7. NEC 422.30(B) REQUIRES THAT THERE BE A DISCONNECT
	FOR THE 80 GAL STORAGE WATER HEATER.
	8. THE 5TH ED. 2014 FBC-ENERGY CONSERVATION SECTION 505
	HAS SPECIFIC REQUIREMENTS FOR COMMERCIAL LIGHTING WHICH
	SHALL BE ADHERED TO. IN ADDITION TO THE LIGHT DENSITY
	CHART, THERE ARE MANDATORY SWITCHING REQUIREMENTS WHICH
	SHALL BE PROVIDED.
	9. YOU SHALL PROVIDE SITE SPECIFIC LOAD CALCS IN
	ACCORDANCE TO NEC 220 PART III. YOUR LOAD CALCS AS
	SUBMITTED DO NOT MATCH THE PANEL ESTIMATED LOADS.
	10. INDICATE THE LOCATION OF THE HVAC EQUIPMENT ON THE
	ELECTRICAL FLOOR PLAN. YOU DO NOT HAVE ANY HVAC
	DRAWINGS OR SPECIFICATIONS ON THE PLANS.
	THE PLANS SHALL BE REVISED TO ADDRESS THE HEREIN
	MENTIONED ITEMS; ONCE CORRECTED SHALL BE RESUBMITTED
	FOR ANOTHER REVIEW.
	WHEN RESUBMITTING, YOU ARE REQUIRED TO PROVIDE A
	RESPONSE LETTER ADDRESSING EACH ITEM ACCOMPANIED WITH
	THE STANDARD CITY RE-SUBMITTAL FORM.
	PLEASE, ADDITIONALLY, INSERT CORRECTED PAGES INTO THE
	SUBMITTAL AND LEAVE THE PREVIOUSLY REVIEWED SHEETS FOR
	COMPARISON. CLOUDING THE CHANGES WILL BE GREATLY
	APPRECIATED.
	IF YOU HAVE FURTHER QUESTIONS, PLEASE DON?T HESITATE TO
	CONTACT ME DIRECTLY.

	PURSUANT TO FS553.80, THE 4TH SUBMITTAL FOR A PERMIT
	WHICH REFLECTS FAILURE TO CORRECT A DEFICIENCY
	PREVIOUSLY SPECIFICALLY AND CONSISTENTLY IDENTIFIED ON
	ALL PRIOR SUBMITTALS MUST RESULT IN THE ASSESSMENT OF A
	PENALTY OF 3 TIMES THE PLAN REVIEW FEE IN ADDITION TO
	THE NORMAL FEE.

	THANK YOU,
	MIKE ALBARRAN
	ELECTRICAL PLANS EXAMINER

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2015-09-16			Cont ID
Sent By	albarran			Date	2015-09-16	Time	19:02	Rev Time	0.00
Received By	albarran			Date	2015-09-16	Time	17:32	Sent To

Notes

2015-09-16 19:03:05	PLEASE NOTE THAT I, MIKE ALBARRAN, ELECTRICAL PLANS
	EXAMINER HAVE COMPLETED THE REVIEW OF THE ABOVE
	MENTIONED JOB. BELOW ARE THE COMMENTS WITH REGARDS TO
	THE REQUIRED CORRECTIONS. THE FOLLOWING ITEMS SHALL BE
	CORRECTED AND THE PLANS RESUBMITTED FOR ANOTHER REVIEW.
	1. FOR SAFE EMERGENCY EGRESS, AN EMERGENCY LIGHT SHALL
	BE INSTALLED IN THE ELECTRICAL ROOM. AN ADDITIONAL
	EMERGENCY LIGHT SHALL BE INSTALLED IN THE HAIR WASH
	AREA.
	2. NEC 422.52, REQUIRES THAT THE ELECTRIC WATER COOLER
	BE CONNECTED TO A GFCI PROTECTED CIRCUIT.
	3. NEC 600.5, REQUIRES THAT EVERY COMMERCIAL OCCUPANCY
	BE PROVIDED WITH AT LEAST ONE OUTLET IN AN ACCESSIBLE
	LOCATION AT EACH ENTRANCE A DEDICATED 20 AMP CIRCUIT
	FOR SIGN OR OUTLINE LIGHTING
	4. NEC 422.30(B), REQUIRES THAT THERE BE A DISCONNECT
	FOR THE 80 GAL STORAGE WATER HEATER.
	5. NEC 210.70 (A)(2), REQUIRES THAT THE STAIRWAY BE
	ILLUMINATED AND THE LIGHT BE CONTROLLED BY A WALL
	SWITCH.
	6. THE 5TH ED. 2014 FBC-ENERGY CONSERVATION SECTION 505
	HAS SPECIFIC REQUIREMENTS FOR COMMERCIAL LIGHTING WHICH
	SHALL BE ADHERED TO.
	7. IN VARIOUS PLACES THROUGHOUT THE NOTES DIFFERENT
	NON-BINDING EDITIONS OF THE NEC ARE QUOTED. PLEASE
	CORRECT THE NOTES TO ADDRESS THE 2011 EDITION OF THE
	NEC.
	8. FIRE ALARM WORK, EVEN THOUGH SHALL BE UNDER A
	SEPARATE PERMIT AND SHOP DRAWING, SHALL BE DESIGNED TO
	COMPLY WITH NFPA 72, 2010 EDITION NOT THE NFPA 96.
	9. YOU SHALL INDICATE ON THE ELECTRICAL RISER DIAGRAM
	WHAT PORTIONS OF IT PERTAIN TO THIS SPECIFIC PROJECT,
	AND INDICATED THE CONDUCTOR SIZING FOR THE APPLICABLE
	PANELS.
	10. THE PANEL SCHEDULES AS PRESENTED DO NOT MATCH THE
	FLOOR PLAN MARKINGS AND CIRCUIT DESIGNATIONS.
	11. ACCORDING TO THE MARKINGS ON THE PANEL DESIGNATOR
	THIS IS A 3 PHASE SERVICE CONTRARY TO THE LAYOUT OF THE
	PANELS. CORRECT ACCORDINGLY.
	12. ACCORDING TO THE SAME PANEL DESIGNATOR, ALL PANELS
	ARE BOTTOM FED. IF THE FEEDERS ARE COMING FROM
	UNDERGROUND, CONDUCTOR INSULATION SHALL BE RATED FOR
	WET LOCATIONS AS INDICATED IN NEC 300.5 (B) AND THE
	ENDS OF THE RACEWAY SEALED ACCORDING TO NEC 300.5(G).
	13. YOU SHALL PROVIDE SITE SPECIFIC LOAD CALCS IN
	ACCORDANCE TO NEC 220 PART III.
	14. INDICATE THE LOCATION OF THE HVAC EQUIPMENT. YOU DO
	NOT HAVE ANY HVAC DRAWINGS OR SPECIFICATIONS ON THE
	PLANS.
	WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RE-SUBMITTAL FORM. PLEASE, ADDITIONALLY, INSERT
	CORRECTED PAGES INTO TO SUBMITTAL AND LEAVE THE
	PREVIOUSLY REVIEWED SHEETS.

	IF YOU HAVE FURTHER QUESTIONS, PLEASE DON?T HESITATE TO
	CONTACT ME DIRECTLY.

	THANK YOU

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2015-07-10			Cont ID
Sent By	dhayes			Date	2015-07-10	Time	10:08	Rev Time	0.00
Received By	dhayes			Date	2015-07-10	Time	10:05	Sent To

Notes

2015-07-10 10:36:05	7/10/2015
	PROJECT: NAIL SALON
	PERMIT#: 15060791
	CODE: 2011EDITION OF THE NEC, FIFTH EDITION OF THE FBC
	, WPB AMENDMENTS TO THE FBC, CHAPTER 1, ADMINISTRATION,
	FBC SUPPLEMENTS.
	1ST ELECTRICAL PLAN REVIEW
	ACTION: DENIED

	REVISE YOUR PLANS IN RESPONSE TO THE FOLLOWING REVIEW
	COMMENTS:

	1) ACCESS TO EXITS SHALL BE MARKED BY APPROVED, READILY
	VISIBLE SIGNS IN ALL CASES WHERE THE EXIT OR WAY TO
	REACH THE EXIT IS NOT READILY APPARENT TO THE
	OCCUPANTS. NFPA 101 SECTION 7.10.1.5.1

	2) EMERGENCY ILLUMINATION SHALL INCLUDE ALL REQUIRED
	MEANS OF EGRESS LIGHTING, ILLUMINATED EXIT SIGNS, AND
	ALL OTHER LIGHTS SPECIFIED AS NECESSARY TO PROVIDE
	REQUIRED ILLUMINATION. EMERGENCY LIGHTING SYSTEMS SHALL
	BE DESIGNED AND INSTALLED SO THAT THE FAILURE OF ANY
	INDIVIDUAL LIGHTING ELEMENT, SUCH AS THE BURNING OUT OF
	A LAMP, CANNOT LEAVE IN TOTAL DARKNESS ANY SPACE THAT
	REQUIRES EMERGENCY ILLUMINATION. NEC 700.16

	3) THE BRANCH CIRCUIT FEEDING THE UNIT EQUIPMENT SHALL
	BE THE SAME BRANCH CIRCUIT AS THAT SERVING THE NORMAL
	LIGHTING IN THE AREA AND CONNECTED AHEAD OF ANY LOCAL
	SWITCHES. THE BRANCH CIRCUIT THAT FEEDS UNIT EQUIPMENT
	SHALL BE CLEARLY IDENTIFIED AT THE DISTRIBUTION PANEL.
	EMERGENCY LUMINAIRES THAT OBTAIN POWER FROM A UNIT
	EQUIPMENT AND ARE NOT PART OF THE UNIT EQUIPMENT SHALL
	BE WIRED TO THE UNIT EQUIPMENT AS REQUIRED BY 700.9 AND
	BY ONE OF THE WIRING METHODS OF NEC CHAPTER 3. NEC
	700.12(F)

	4) PLEASE INDICATE COMPLIANCE WITH FBC-ENERGY.
	ELECTRICAL POWER AND LIGHTING SYSTEMS. (MANDATORY)
	SECTION 505

	5) RECESSED LUMINAIRES INSTALLED IN THE BUILDING
	THERMAL ENVELOPE SHALL BE IC AND AIR TIGHT RATED AND
	SEALED TO LIMIT AIR LEAKAGE BETWEEN CONDITIONED AND
	UNCONDITIONED SPACES. FBC-E 502.3.8 RECESSED LIGHTING.

	6) AT LEAST ONE RECEPTACLE OUTLET SHALL BE INSTALLED
	WITHIN 450 MM (18 IN.) OF THE TOP OF SHOW WINDOW FOR
	EACH 3.7 LINEAR M (12 LINEAR FT) OR MAJOR FRACTION
	THEREOF OF SHOW WINDOW AREA MEASURED HORIZONTALLY AT
	ITS MAXIMUM WIDTH. NEC 210.62

	7) EACH COMMERCIAL OCCUPANCY ACCESSIBLE TO PEDESTRIANS
	SHALL BE PROVIDED WITH AT LEAST ONE OUTLET SUPPLIED BY
	A BRANCH CIRCUIT RATED AT LEAST 20 AMPERES THAT
	SUPPLIES NO OTHER LOAD. NEC 600.5

	8) BOXES LISTED SPECIFICALLY FOR THIS APPLICATION SHALL
	BE USED FOR RECEPTACLES LOCATED IN THE FLOOR. NEC
	314.27(C)

	9) PROVIDE PRODUCT APPROVALS FOR THE WATER HEATER AND
	INDICATE THE APPROPRIATE SIZE CIRCUIT AND DISCONNECT
	REQUIRED. NEC 422.31

	10) SEPARATE PERMIT APPLICATIONS ACCOMPANIED BY
	MANUFACTURERS EQUIPMENT SUBMITTALS, AND SHOP DRAWINGS
	ARE REQUIRED FOR FIRE ALARM, ACCESS CONTROL SYSTEM,
	SECURITY, CCTV, AUDIO/VIDEO, NETWORK, DATA, AND,
	COMMUNICATION.

	WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RE-SUBMITTAL FORM. SEE LINK:
	HTTP://WPB.ORG/DEVELOPMENT/WP-CONTENT/UPLOADS/SITES/33/
	2013/09/APPLICATION_RESUBMITTAL_FORM_04132010.PDF

	A THOROUGH REVIEW CANNOT BE MADE AT THIS TIME, AS A
	RESULT OF THE ADDITIONAL INFORMATION REQUESTED
	ADDITIONAL COMMENTS MAY APPEAR THAT WERE NOT PART OF
	THIS REVIEW.
	ADDITIONALLY, IT IS REQUIRED TO INSERT THE CORRECTED
	PAGES INTO THE DENIED SUBMITTAL PACKAGE. VOID THE
	PREVIOUSLY REVIEWED SHEETS AND LEAVE FOR COMPARATIVE
	REVIEW.
	DAVID HAYES, ELECTRICAL PLANS EXAMINER, PX3421,
	561-805-6717 OR [email protected]

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	2	Status	P	Date	2015-09-03			Cont ID
Sent By	pleduc			Date	2015-09-03	Time		Rev Time	0.00
Received By	pleduc			Date	2015-09-03	Time	11:51	Sent To

Notes

***NONE***

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2015-06-22			Cont ID
Sent By	pleduc			Date	2015-06-22	Time		Rev Time	0.00
Received By	pleduc			Date	2015-06-22	Time	13:41	Sent To

Notes

2015-06-22 14:08:52	THIS PLAN WAS REVIEWED AND FAILED BY PETER LEDUC, FIRE
	MARSHAL, WITH THE FOLLOWING COMMENTS:

	1) THE PROPOSED PROJECT SHALL MEET THE REQUIREMENTS OF
	THE 5TH EDITION OF FLORIDA FIRE PREVENTION CODE
	INCLUDING THE 2012 EDITION OF NFPA 1 AND NFPA 101 AND
	ALL OTHER APPLICABLE CODES OR STANDARDS.
	FIRE SPRINKLER WORK SHALL COMPLY WITH THE REQUIREMENTS
	OF NFPA 13, 2010 EDITION.
	FIRE ALARM WORK SHALL COMPLY WITH THE REQUIREMENTS OF
	NFPA 72, 2010 EDITION.
	CONSTRUCTION WORK SHALL COMPLY WITH THE REQUIREMENTS OF
	NFPA 241, 2009 EDITION.
	FIRE EXTINGUISHERS SHALL COMPLY WITH THE REQUIREMENTS
	OF NFPA 10, 2010 EDITION.
	ELECTRIC WORK SHALL COMPLY WITH NFPA 70, 2011 EDITION.

	2) A DOOR SCHEDULE, INCLUDING HARDWARE IS NOT PROVIDED.

	3) THE BATHROOM DOOR OPENS AND RESTRICTS THE MEANS OF
	EGRESS. IT SHALL SWING INTO THE BATHROOM. NFPA 101
	CHAPTER 7, MEANS OF EGRESS
	7.2.1.4.3 DOOR LEAF ENCROACHMENT
	7.2.1.4.3.1 DURING ITS SWING, ANY DOOR LEAF IN A MEANS
	OF EGRESS SHALL LEAVE NOT LESS THAN ONE-HALF OF THE
	REQUIRED WIDTH OF AN AISLE, A CORRIDOR, A PASSAGEWAY,
	OR A LANDING UNOBSTRUCTED AND SHALL NOT PROJECT NOT
	MORE THAN 7 IN. INTO THE REQUIRED WIDTH OF AN AISLE, A
	CORRIDOR, A PASSAGE WAY, OR A LANDING, WHEN FULLY OPEN,
	UNLESS BOTH OF THE FOLLOWING CONDITIONS ARE MET:
	(1) THE DOOR OPENING PROVIDES ACCESS TO A STAIR IN AN
	EXISTING BUILDING.
	(2) THE DOOR OPENING MEETS THE REQUIREMENTS THAT LIMITS
	PROJECTION TO NOT MORE THAN 7 IN. INTO THE REQUIRED
	WIDTH OF THE STAIR LANDING WHEN THE DOOR LEAF IS FULLY
	OPEN.

	4) AN EXIT LIGHT SHALL BE INSTALLED AT THE REAR DOOR.

	5) AN EXIT LIGHT SHALL BE INSTALLED LEADING INTO THE
	REAR EXIT CORRIDOR.

	6) THE NATURE OF THE REMODE, IF EXISTING,L REQUIRES AN
	EVALUATION OF THE FIRE ALARM AND SPRINKLER SYSTEM FOR
	CODE COVERAGE AND COMPLIANCE. ANY REMOVAL AND/OR
	CONSTRUCTION OF WALLS REQUIRES AN EVALUATION. PLEASE
	PROVIDE A NOTE INDICATING ANY EXISTING SYSTEM(S).
	IF EXISTING, THE LIFE SAFETY SYSTEMS, FIRE ALARM AND/OR
	FIRE SPRINKLER SHALL REMAIN ACTIVE THROUGHOUT THE
	CONSTRUCTION PERIOD.
	IF INDICATED, ANY AND ALL WORK ON THE FIRE ALARM AND
	FIRE SPRINKLER SYSTEMS SHALL BE DONE UNDER SEPARATE
	SHOP DRAWINGS AND BY CERTIFIED LIFE SAFETY CONTRACTORS.
	ANY TIME THAT WORK ON THE LIFE SAFETY SYSTEMS,
	SPRINKLER AND/OR FIRE ALARM, EXCEEDS 4 HOURS, A FIRE
	WATCH SHALL BE IMPLEMENTED AND MAINTAINED UNTIL FULL
	AND COMPLETE PROTECTION IS RETURNED.

Review Stop	I			INCOMING/PROCESSING
Rev No	4	Status	N	Date	2015-11-30			Cont ID
Sent By	albarran			Date	2015-11-30	Time	16:05	Rev Time	0.00
Received By	albarran			Date	2015-11-12	Time	10:00	Sent To

Notes

2015-11-30 16:08:18	11/30/15 ELECTRIC APPROVED WITH THE FOLLOWING PROVISO:
	ELECTRICAL PROVISO TO PERMIT 15090791 1. INSTALL
	EMERGENCY LIGHT IN ELECTRIC ROOM 2. INSTALL THE MISSING
	SIGN OUTLETS FOR THE REAR ENTRIES AS REQUIRED IN NEC
	600.5 PER CONVERSATION W/MR. PETERKIN. CONTRACTOR
	NOTIFIED VIA EMAIL. SENT TO LARGE READY BIN "H." MA

2015-11-13 10:01:00	RESUB ROUTED TO CCOLE

Review Stop	I			INCOMING/PROCESSING
Rev No	3	Status	N	Date	2015-10-28			Cont ID
Sent By	albarran			Date	2015-10-28	Time	14:03	Rev Time	0.00
Received By	albarran			Date	2015-10-06	Time	13:00	Sent To

Notes

2015-10-28 14:04:09	10/28/15 FAILED ELECTRICAL PLAN REVIEW FOR A THIRD
	TIME. NOTICE OF ADDITIONAL FEE FOR FAILING NEXT REVIEW
	WAS MADE ON FRONT SCREEN AND TO CUSTOMER VIA EMAIL WHEN
	NOTIFIED OF FAILED STATUS. SENT TO LARGE DENIED BIN
	"H". MA
2015-10-07 13:00:39	C33

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2015-09-21			Cont ID
Sent By	jwitmer			Date	2015-09-21	Time	14:39	Rev Time	0.00
Received By	jwitmer			Date	2015-09-02	Time	15:44	Sent To

Notes

2015-09-02 15:45:27

C36

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2015-07-10			Cont ID
Sent By	dhayes			Date	2015-07-10	Time	10:36	Rev Time	0.00
Received By	dhayes			Date	2015-06-18	Time	14:00	Sent To

Notes

2015-06-18 14:01:26

INCOMING SENT TO C-35 BOX.

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	3	Status	N	Date	2015-10-19			Cont ID
Sent By	jwitmer			Date	2015-10-19	Time	14:59	Rev Time	0.00
Received By	jwitmer			Date	2015-10-19	Time	14:59	Sent To

Notes

2015-10-19 15:02:19	IMPACT FEES
	MU-2015-022185-0000
	REC:2015-0922-182
	FEES PAID: $142.67
	J. WITMER

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	2	Status	F	Date	2015-09-21		Cont ID
Sent By				Date	2015-09-21	Time	Rev Time	0.00
Received By				Date	2015-09-21	Time	Sent To

Notes

2015-09-21 14:39:27	2ND REQUEST, ADDITIONAL SQUARE FOOTAGE ADDED. BEFORE A
	PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT FEES MUST BE
	PAID TO PALM BEACH COUNTY. THE ACTUAL PERMIT SET OF
	PLANS MUST BE STAMPED BY THAT OFFICE, AND A COPY OF THE
	PAID RECEIPT ATTACHED TO THE PERMIT APPLICATION. PLEASE
	CALL (561)233-5025 FOR MORE INFORMATION.

Review Stop	IMPACT			COUNTY IMPACT FEES
Rev No	1	Status	F	Date	2015-06-22			Cont ID
Sent By	jwitmer			Date	2015-06-22	Time	06:12	Rev Time	0.00
Received By	jwitmer			Date	2015-06-22	Time	06:12	Sent To

Notes

***NONE***

Review Stop	M			MECHANICAL (A/C)
Rev No	4	Status	P	Date	2015-11-19			Cont ID
Sent By	ccole			Date	2015-11-19	Time	11:51	Rev Time	0.00
Received By	ccole			Date	2015-11-19	Time	11:51	Sent To

Notes

***NONE***

Review Stop	M			MECHANICAL (A/C)
Rev No	3	Status	F	Date	2015-10-27			Cont ID
Sent By	ccole			Date	2015-10-27	Time	16:09	Rev Time	0.00
Received By	ccole			Date	2015-10-27	Time	16:09	Sent To

Notes

2015-10-27 16:30:22	3RD REVIEW: FBC 2014 MECHANICAL
	PERMIT #15060791
	10/27/15

	1) PROVIDE EQUIPMENT SCHEDULES ON THE PLANS FOR THE
	INTAKE AND EXHAUST FANS INCLUDING MAKES AND MODELS, CFM
	CAPACITIES, ELECTRICAL DATA ETC.
	2) THE MECHANICAL DAMPERS SHOWN ON THE EXTRERIOR WALLS
	COVERING THE FANS MUST BE WIND AND WATER RESISTANT- SEE
	SECTIONS 401.5 AND 501.2.2 FBC-10 MECHANICAL AND SUBMIT
	MANUFACTURER'S SPECIFICATIONS THAT INDICATE COMPLIANCE.
	3) PLEASE REFER TO SECTION 1609.1.2 (PROTECTION OF
	OPENINGS) AND 1609.6.4.4.1 (COMPONENTS AND CLADDING)
	FBC-10 BUILDING, AND PROVIDE TWO COPIES OF FLORIDA
	PRODUCT APPROVALS OR MIAMI-DADE NOA'S FOR THE DAMPERS-
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS RULE 9N-3.
	4) SUBMIT MANUFACTURER'S SPECIFICATIONS FOR THE
	FLEXIBLE EXHAUST HOSES. REFER TO SECTION 501.4: EXHAUST
	DUCTS SHALL BE OF METAL AND SUCH CONSTRUCTION SHALL
	COMPLY WITH CHAPTER 6 FBC-10 MECHANICAL. PLEASE NOTE
	THAT THIS SECTION DOES NOT RESTRICT THE USE OF
	ALTERNATE MATERIALS IF LISTED AND LABELED FOR THE USE
	SPECIFIED ON THE PLAN.
	5) IT APPEARS THAT THE EXHAUST DISCHARGE AT THE REAR OF
	THE BUILDING IS WITHIN THE MINIMUM 10 FT. REQUIRED
	CLEARANCE DISTANCE TO THE REAR DOOR OPENING- REFER TO
	SECTION 501.2.1 FBC-10 MECHANICAL AND INDICATE
	COMPLIANCE.
	6) INDICATE THE CLEARANCE DISTANCE MEASUIREMENT FROM
	THE NEW AIR INTAKE AT THE REAR OF THE BUILDING TO THE
	PARKING LOT AND DRIVE AREAS- REFER TO SECTION 401.4 AND
	401.4.1 FBC-10 MECHANICAL.

	CHRISTOPHER L. COLE
	MECHANICAL PLANS EXAMINER
	561-805-6719
	[email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2015-09-09			Cont ID
Sent By	ccole			Date	2015-09-09	Time	08:19	Rev Time	0.00
Received By	ccole			Date	2015-09-09	Time	08:19	Sent To

Notes

2015-09-09 08:29:55	2ND REVIEW: FBC 2010 MECHANICAL
	PERMIT #15060791
	9/9/2015

	1) COMMENT #1 FROM THE 1ST REVIEW STILL EXISTS.
	ALTHOUGH THE REVISED PLAN DOES SHOW A NEW EXHAUST FAN,
	THE LOCATION OF THE FAN DOES NOT COMPLY WITH FOOTNOTE H
	UNDER TABLE 403.3 FBC-10 MECHANICAL WHICH REQUIRES
	CONTAMINANTS AND ODORS TO BE CAPTURED AT THEIR SOURCES.
	I AM RE-PRINTING THE COMMENT HERE FOR REVIEW:
	(AN EXHAUST VENTILATION SYSTEM DESIGNED IN ACCORDANCE
	WITH TABLE 403.3 FBC-20 MECHANICAL IS REQUIRED FOR THE
	NEW NAIL SALON. PLEASE REFER TO FOOTNOTES B AND H AT
	THE BOTTOM OF THE TABLE FOR SPECIFIC REQUIREMENTS FOR
	NAIL SALONS: B) MECHANICAL EXHAUST IS REQUIRED AND THE
	RECIRCULATION OF AIR FROM SUCH SPACES IS PROHIBITED
	(SEE SECTION 403.2.1, ITEM 3: WHERE MECHANICAL EXHAUST
	IS REQUIRED BY NOTE B IN TABLE 403.3, RECIRCULATION OF
	AIR FROM SUCH SPACES SHALL BE PROHIBITED. ALL AIR
	SUPPLIED TO SUCH SPACES SHALL BE EXHAUSTED, INCLUDING
	ANY AIR IN EXCESS OF THAT REQUIRED BY TABLE 403.3). H)
	FOR NAIL SALONS, THE REQUIRED EXHAUST SHALL INCLUDE
	VENTILATION TABLES OR OTHER SYSTEMS THAT CAPTURE THE
	CONTAMINANTS AND ODORS AT THEIR SOURCE AND ARE CAPABLE
	OF EXHAUSTING A MINIMUM OF 50 CFM PER STATION. THIS
	REQUIREMENT APPLIES TO BOTH MANICURE AND PEDICURE
	STATIONS. PLEASE REVISE THE PLANS ACCORDINGLY.) IN
	ORDER FOR THE SALON TO BE IN COMPLIANCE, EXHAUST INLETS
	MUST BE PLACED AT EVERY MANICURE TABLE AND PEDICURE
	STATION IN THE FACILITY, AND MAKE-UP AIR MUST BE
	PROVIDED AT THESE LOCATIONS FOR THE EXHAUST. THE SYSTEM
	MUST BE INDEPENDENT OF THE MAIN HVAC SYSTEM, AND MUST
	BE DESIGNED TO BE AIR IN/ AIR OUT WITH NO RECIRCULATION
	OF EXHAUST.
	2) PLEASE REVISE THE OUTDOOR AIR CALCULATIONS ON SHEET
	A-2 TO INCLUDE THE EXHAUST CFM'S PER SQ. FT., AND
	PROVIDE AN AIR BALANCE CALCULATION.

	IF YOU HAVE ANY QUESTIONS PLEASE CONTACT ME.

	CHRISTOPHER L. COLE
	MECHANICAL PLANS EXAMINER
	561-805-6719
	[email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2015-07-09			Cont ID
Sent By	ccole			Date	2015-07-09	Time	16:08	Rev Time	0.00
Received By	ccole			Date	2015-07-09	Time	16:08	Sent To

Notes

2015-07-09 16:35:16	1ST REVIEW: FBC 2010 MECHANICAL
	PERMIT #15060791 7/9/15

	1) AN EXHAUST VENTILATION SYSTEM DESIGNED IN ACCORDANCE
	WITH TABLE 403.3 FBC-20 MECHANICAL IS REQUIRED FOR THE
	NEW NAIL SALON. PLEASE REFER TO FOOTNOTES B AND H AT
	THE BOTTOM OF THE TABLE FOR SPECIFIC REQUIREMENTS FOR
	NAIL SALONS: B) MECHANICAL EXHAUST IS REQUIRED AND THE
	RECIRCULATION OF AIR FROM SUCH SPACES IS PROHIBITED
	(SEE SECTION 403.2.1, ITEM 3: WHERE MECHANICAL EXHAUST
	IS REQUIRED BY NOTE B IN TABLE 403.3, RECIRCULATION OF
	AIR FROM SUCH SPACES SHALL BE PROHIBITED. ALL AIR
	SUPPLIED TO SUCH SPACES SHALL BE EXHAUSTED, INCLUDING
	ANY AIR IN EXCESS OF THAT REQUIRED BY TABLE 403.3). H)
	FOR NAIL SALONS, THE REQUIRED EXHAUST SHALL INCLUDE
	VENTILATION TABLES OR OTHER SYSTEMS THAT CAPTURE THE
	CONTAMINANTS AND ODORS AT THEIR SOURCE AND ARE CAPABLE
	OF EXHAUSTING A MINIMUM OF 50 CFM PER STATION. THIS
	REQUIREMENT APPLIES TO BOTH MANICURE AND PEDICURE
	STATIONS. PLEASE REVISE THE PLANS ACCORDINGLY.
	2) THE SUBMITTED PLAN SHOWS A NEW O/A INTAKE PROVIDING
	680 CFM TO THE AHU. PROVIDE A VENTILATION CALCULATION
	IN ACCORDANCE WITH TABLE 403.3 TO VERIFY THE MINIMUM
	RATE COMPLIANCE.
	3) INDICATE ON THE PLAN THE AIR INTAKE OPENING WILL BE
	LOCATED TO MEET OR EXCEED THE REQUIRED CLEARANCE
	DISTANCES OUTLINED IN SECTION 401.4.1, AND THE OPENING
	WILL BE PROTECTED IN COMPLIANCE WITH 401.5. PROVIDE TWO
	COPIES OF A FLORIDA PRODUCT APPROVAL OR MIAMI-DADE NOA
	FOR THE INTAKE LOUVER.
	4) A COMPLETE REVIEW OF THE PROJECT CANNOT BE COMPLETED
	AT THIS TIME DUE TO THE LACK OF DETAILS ON THE
	SUBMITTED PLANS.

	CHRISTOPHER L. COLE
	MECHANICAL PLANS EXAMINER
	561-805-6719
	[email protected]

Review Stop	P			PLUMBING
Rev No	3	Status	P	Date	2015-10-14			Cont ID
Sent By	gjohnson			Date	2015-10-14	Time	14:11	Rev Time	0.00
Received By	gjohnson			Date	2015-10-14	Time	14:11	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	2	Status	F	Date	2015-09-10			Cont ID
Sent By	gjohnson			Date	2015-09-10	Time	14:09	Rev Time	0.00
Received By	gjohnson			Date	2015-09-10	Time	14:09	Sent To

Notes

2015-09-10 14:12:22	1ST REVIEW: FBC 2014

	GEORGE JOHNSON
	PLUMBING PLANS EXAMINER
	561-805-6711
	[email protected]



	PLUMBING COMMENTS:
	.
	1.WATER FOUNTAIN S SHALL COMPLY WITH FBC ACC. SEC.
	211.2 MINIMUM NUMBER.
	NO FEWER THAN TWO DRINKING FOUNTAINS SHALL BE PROVIDED.
	ONE DRINKING FOUNTAIN SHALL COMPLY WITH 602.1 THROUGH
	602.6 AND ONE DRINKING FOUNTAIN SHALL COMPLY WITH 602.7
	2. PROVIDE INFORMATION AND MANUFACTURE SPEC SHEETS ON
	THE PEDICURE CHAIRS. DELETING THEM OFF PLUMBING PLAN
	DOES NOT COMPLY WE NEED TO SEE HOW THEY WORK .
	WPB AMEND. 107.2.1

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2015-06-20			Cont ID
Sent By	tklarge			Date	2015-06-20	Time	06:46	Rev Time	0.00
Received By	tklarge			Date	2015-06-20	Time	05:10	Sent To

Notes

2015-06-20 06:39:01	1) SHT. A-1 - IDENTIFY THE ROOM WITH THE SINK THAT IS
	LOCATED NEAR THE HAIR WASH SINKS. WPB AMEND.TO 2010 FBC
	SEC. 107.2.1.
	2) A DRINKING FOUNTAIN IS REQUIRED IN A BUSINESS
	OCCUPANCY PER TABLE 403.1 OF THE 2010 FPC. NO FEWER
	THAN TWO DRINKING FOUNTAINS SHALL BE PROVIDED IN
	ACCORDANCE WITH THE 2010 FL. ACCESSIBILITY CODE SEC.
	211.2 & FOOTNOTE # E OF TABLE 403.1 OF FPC.
	3) ONE HAIR WASH SINK SHALL BE ACCESSIBLE PER SEC.212
	OF FL. ACCESSIBILITY CODE.
	4) SHT. A-3 - WATER HEATER DETAIL - THE RELIEF LINE
	SHALL DISCHARGE THROUGH AN AIR GAP LOCATED IN THE SAME
	ROOM AS THE WATER HEATER PERR 2010 FPC SEC. 504.6
	(2).THE PLAN SHOWS IT DISCHARGING TO THE EXTERIOR.
	5) IDENTIFY THE ACCESSIBLE RESTROOM ON THE FLOOR PLAN
	AND CLEARLY SHOW THE DIMENSIONS. (L X W). *5 INCHES IS
	THE MINIMUM WIDTH IF BUILT PERFECT, 86 INCHES ALLOWS
	FOR TOLERANCES.
	6) GRAB BARS SHALL BE MEASURED FORM THE FINISH FLOOR TO
	THE TOP OF THE GRIPPING SURFACE PER THE 2010 FAC SEC.
	609.4.
	7) SHT. P-2 - THE PEDICURE CHAIRS ARE NOT VENTED. 201
	FPC SEC.901.2.1.
	8) IF THE PEDICURE CHAIRS ARE GOING TO BE WET VENTED
	THE MAXIMUM NUMBER OF FIXTURE UNITS ON A HORIZONTAL WET
	VENT SHALL COMPLY WITH TABLE 909.3 OF 2010 FPC.
	9) SIZE THE LOOP VENT FOR THE HAIR SINKS. COMPLY WITH
	2010 FPC SEC. 916.1 & TABLE 916.1.
	10) CLEANOUTS ARE REQUIRED IN STACKS PER 2010 FPC
	SEC.708.3.4.
	11) SIZE ALL SECTIONS OF THE BUILDING DRAIN PER TABLE
	710.1 (1).
	12) SHT. P-2 CALLS OUT THE ADA BATH AS NEW & SHT. P-1
	NOTES IT AS EXISTING. CLARIFY.
	13) SHOW THE REQUIRED SHUTOFF VALVES TO THE PLUMBING
	FIXTURES PER 2010 FPC SEC.606.1, 606.2.
	14) SHT. P-2 - SHOW THE LOCATION WHERE THE WATER SUPPLY
	ENTERS THE STRUCTURE. WPB AMEND. TO 2010 FPC
	107.3.5.1.3.
	15) SUBMIT TWO COPIES OF THE MANUFACTURER'S
	SPECIFICATIONS SHEETS AND INSRTALLATION MANUAL FOR THE
	PEDICURE CHAIRS.
	WPB AMEND.TO 2010 FBC SEC. 107.2.1.
	16) THE PLANS NOTE THAT THE APPLICABLE CODES ARE THE
	2014 FBC. THE CODE IN EFFECT FOR THIS PERMIT IS THE
	2010 FBC. CLARIFY.
	17) SHT. A-1 - NOTES THAT THE OCCUPANCY IS BASED ON AN
	AREA NOTED AS SALES AREA. THE TYPE OF OCCUPANCY FOR A
	NAIL SALON WOULD BE A BUSINESS OCCUPANCY. THE OCCUPANT
	LOAD WOULD BE 100 SQ. FT. PER PERSON BUT THE PLAN NOTES
	60 SQ. FT. PER PERSON. CLARIFY.

	PLUMBING PLAN REVIEW
	TIM LARGE
	CHIEF PLUMBING INSPECTOR
	561-805-6692
	[email protected]