City of West Palm Beach eGovPlus

Plan Review Details - Permit 15010163

Plan Review Stops For Permit 15010163

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	4	Status	P	Date	2015-06-25			Cont ID
Sent By	rmcdouga			Date	2015-06-25	Time	17:51	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-25	Time	17:51	Sent To

Notes

***NONE***

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	3	Status	F	Date	2015-06-24			Cont ID
Sent By	rmcdouga			Date	2015-06-24	Time	19:01	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-24	Time	15:23	Sent To

Notes

2015-06-24 19:02:36	PLAN
	REVIEW COMMENTS

	2ND REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	DENIED BY BUILDING
	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) FBC 107.2.1 - INFORMATION ON CONSTRUCTION DOCUMENTS.
	ALL INFORMATION, DRAWINGS, SPECIFICATIONS AND
	ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE OF
	THE PERSON RESPONSIBLE FOR THE DESIGN.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2015-05-07			Cont ID
Sent By	tklarge			Date	2015-05-07	Time	19:10	Rev Time	0.00
Received By	rmcdouga			Date	2015-05-07	Time	16:46	Sent To	Z

Notes

2015-05-07 18:06:22	PLAN
	REVIEW COMMENTS

	1ST REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	DENIED BY BUILDING
	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) 1) FBC107.1 GENERAL. SUBMITTAL DOCUMENTS CONSISTING
	OF CONSTRUCTION DOCUMENTS, STATEMENT OF SPECIAL
	INSPECTIONS, GEOTECHNICAL REPORT AND OTHER DATA SHALL
	BE SUBMITTED IN TWO OR MORE SETS WITH EACH PERMIT
	APPLICATION. THE CONSTRUCTION DOCUMENTS SHALL BE
	PREPARED BY A REGISTERED DESIGN PROFESSIONAL WHERE
	REQUIRED BY CHAPTER 471, FLORIDA STATUTES & 61G15
	FLORIDA ADMINISTRATIVE CODE OR CHAPTER 481, FLORIDA
	STATUTES & 61G1 FLORIDA ADMINISTRATIVE CODE.

	2) FBC 107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE DIMENSIONED AND DRAWN
	UPON SUITABLE MATERIAL. CONSTRUCTION DOCUMENTS SHALL BE
	OF SUFFICIENT CLARITY TO INDICATE THE LOCATION, NATURE
	AND EXTENT OF THE WORK PROPOSED AND SHOW IN DETAIL THAT
	IT WILL CONFORM TO THE PROVISIONS OF THIS CODE AND
	RELEVANT LAWS, ORDINANCES, RULES AND REGULATIONS, AS
	DETERMINED BY THE BUILDING OFFICIAL. SUCH DRAWINGS AND
	SPECIFICATIONS SHALL CONTAIN INFORMATION, IN THE FORM
	OF NOTES OR OTHERWISE, AS TO THE QUALITY OF MATERIALS,
	WHERE QUALITY IS ESSENTIAL TO CONFORMITY WITH THE
	TECHNICAL CODES. SUCH INFORMATION SHALL BE SPECIFIC,
	AND THE TECHNICAL CODES SHALL NOT BE CITED AS A WHOLE
	OR IN PART, NOR SHALL THE TERM "LEGAL" OR ITS
	EQUIVALENT BE USED AS A SUBSTITUTE FOR SPECIFIC
	INFORMATION. ALL INFORMATION, DRAWINGS, SPECIFICATIONS
	AND ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE
	OF THE PERSON RESPONSIBLE FOR THE DESIGN.

	3) FBC 107.2.1.4 QUALITY OF BUILDING PLANS. BUILDING
	PLANS SHALL BE DRAWN TO A MINIMUM 1/8 INCH SCALE UPON
	SUBSTANTIAL PAPER, CLOTH OR OTHER ACCEPTABLE MEDIUM.
	THIS POLICY MAY INCLUDE SUCH THINGS AS MINIMUM SIZE,
	SHAPE, CONTRAST, CLARITY, OR OTHER ITEMS RELATED TO
	RECORDS MANAGEMENT.

	4) FBC-R314.3.1 WHEN ALTERATIONS, REPAIRS OR ADDITIONS
	REQUIRING A PERMIT OCCUR, OR WHEN ONE OR MORE SLEEPING
	ROOMS ARE ADDED OR CREATED IN EXISTING DWELLINGS, THE
	INDIVIDUAL DWELLING UNIT SHALL BE EQUIPPED WITH SMOKE
	ALARMS LOCATED AS REQUIRED FOR NEW DWELLINGS.

	5) FBC-R807.1 ATTIC ACCESS.
	BUILDINGS WITH COMBUSTIBLE CEILING OR ROOF CONSTRUCTION
	SHALL HAVE AN ATTIC ACCESS OPENING TO ATTIC AREAS THAT
	EXCEED 30 SQUARE FEET (2.8 M2) AND HAVE A VERTICAL
	HEIGHT OF 30 INCHES (762 MM) OR GREATER. THE VERTICAL
	HEIGHT SHALL BE MEASURED FROM THE TOP OF THE CEILING
	FRAMING MEMBERS TO THE UNDERSIDE OF THE ROOF FRAMING
	MEMBERS.
	THE ROUGH-FRAMED OPENING SHALL NOT BE LESS THAN 22
	INCHES BY 30 INCHES (559 MM BY 762 MM) AND SHALL BE
	LOCATED IN A HALLWAY OR OTHER READILY ACCESSIBLE
	LOCATION. WHEN LOCATED IN A WALL, THE OPENING SHALL BE
	A MINIMUM OF 22 INCHES WIDE BY 30 INCHES HIGH. WHEN THE
	ACCESS IS LOCATED IN A CEILING, MINIMUM UNOBSTRUCTED
	HEADROOM IN THE ATTIC SPACE SHALL BE AT SOME POINT 30
	INCHES (762 MM ABOVE THE ACCESS MEASURED VERTICALLY
	FROM THE BOTTOM OF CEILING FRAMING MEMBERS. SEE SECTION
	M1305.1.3 FOR ACCESS REQUIREMENTS WHERE MECHANICAL
	EQUIPMENT IS LOCATED IN ATTICS.

	6) FBC 107.3.5.3 - PROVIDE WIND DESIGN LOADS AND
	COMPONENT AND CLADDING DESIGN PRESSURES PURSUANT TO
	FBC-R301.2.

	7) SHOW COMPLIANCE WITH FBC-R310.1 EMERGENCY ESCAPE AND
	RESCUE REQUIRED.
	BASEMENTS, HABITABLE ATTICS AND EVERY SLEEPING ROOM
	SHALL HAVE AT LEAST ONE OPERABLE EMERGENCY ESCAPE AND
	RESCUE OPENING. WHERE BASEMENTS CONTAIN ONE OR MORE
	SLEEPING ROOMS, EMERGENCY EGRESS AND RESCUE OPENINGS
	SHALL BE REQUIRED IN EACH SLEEPING ROOM. WHERE
	EMERGENCY ESCAPE AND RESCUE OPENINGS ARE PROVIDED THEY
	SHALL HAVE A SILL HEIGHT OF NOT MORE THAN 44 INCHES
	(1118 MM) ABOVE THE FLOOR. WHERE A DOOR OPENING HAVING
	A THRESHOLD BELOW THE ADJACENT GROUND ELEVATION SERVES
	AS AN EMERGENCY ESCAPE AND RESCUE OPENING AND IS
	PROVIDED WITH A BULKHEAD ENCLOSURE, THE BULKHEAD
	ENCLOSURE SHALL COMPLY WITH SECTION R310.3. THE NET
	CLEAR OPENING DIMENSIONS REQUIRED BY THIS SECTION SHALL
	BE OBTAINED BY THE NORMAL OPERATION OF THE EMERGENCY
	ESCAPE AND RESCUE OPENING FROM THE INSIDE. EMERGENCY
	ESCAPE AND RESCUE OPENINGS WITH A FINISHED SILL HEIGHT
	BELOW THE ADJACENT GROUND ELEVATION SHALL BE PROVIDED
	WITH A WINDOW WELL IN ACCORDANCE WITH SECTION R310.2.
	EMERGENCY ESCAPE AND RESCUE OPENINGS SHALL OPEN
	DIRECTLY INTO A PUBLIC WAY, OR TO A YARD OR COURT THAT
	OPENS TO A PUBLIC WAY.
	R310.1.1 MINIMUM OPENING AREA.
	ALL EMERGENCY ESCAPE AND RESCUE OPENINGS SHALL HAVE A
	MINIMUM NET CLEAR OPENING OF 5.7 SQUARE FEET (0.530
	M2).
	EXCEPTION: GRADE FLOOR OPENINGS SHALL HAVE A MINIMUM
	NET CLEAR OPENING OF 5 SQUARE FEET (0.465 M2).
	R310.1.2 MINIMUM OPENING HEIGHT.
	THE MINIMUM NET CLEAR OPENING HEIGHT SHALL BE 24 INCHES
	(610 MM).
	R310.1.3 MINIMUM OPENING WIDTH.
	THE MINIMUM NET CLEAR OPENING WIDTH SHALL BE 20 INCHES
	(508 MM).
	*NOTE: BEDROOM 5 HAS NO EXTERIOR WALLS.

	8) PROVIDE THE DESIGN MANUAL FILE NUMBER AND DETAIL OF
	THE (2) HOUR FIRE RATED WALL ASSEMBLY THAT WILL BE USED
	AT BATH 2.

	9) FBC 107.3.4 - PROVIDE TWO SETS OF PRODUCT APPROVALS
	FOR THOSE PRODUCTS WHICH ARE REGULATED BY DCA RULE 9N-3
	THAT HAVE BEEN REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD. PROVIDE TWO COMPLETE PRODUCT
	APPROVALS WITH FL OR NOA NUMBERS INCLUDING INSTALLATION
	INSTRUCTIONS AND MAXIMUM DESIGN PRESSURES FOR EACH OF
	THE DIFFERENT ROOFING MATERIALS, WINDOW/GLASS TYPES,
	STRUCTURAL MULLIONS AND EXTERIOR DOOR TYPES. THERE IS
	NO FL OR NOA NUMBER ON THE INFORMATION THAT WAS
	SUBMITTED FOR THE SINGLE HUNG WINDOWS. THERE WAS NO
	PRODUCT APPROVAL SUBMITTED FOR THE STRUCTURAL MULLIONS
	FOR THE DOUBLE WINDOWS.

	10) IN ORDER TO REDUCE PLAN REVIEW TIMES AND PROVIDE
	CLARIFICATION, PLEASE SUBMIT A RESPONSE LETTER
	INDICATING HOW EACH OF THE REVIEW COMMENTS HAS BEEN
	ADDRESSED.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2015-01-20			Cont ID
Sent By	rmcdouga			Date	2015-01-20	Time	18:59	Rev Time	0.00
Received By	rmcdouga			Date	2015-01-20	Time	18:42	Sent To

Notes

2015-01-20 18:59:07	PLAN REVIEW COMMENTS

	1ST REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	DENIED BY BUILDING
	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) FBC 107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE DIMENSIONED AND DRAWN
	UPON SUITABLE MATERIAL. CONSTRUCTION DOCUMENTS SHALL BE
	OF SUFFICIENT CLARITY TO INDICATE THE LOCATION, NATURE
	AND EXTENT OF THE WORK PROPOSED AND SHOW IN DETAIL THAT
	IT WILL CONFORM TO THE PROVISIONS OF THIS CODE AND
	RELEVANT LAWS, ORDINANCES, RULES AND REGULATIONS, AS
	DETERMINED BY THE BUILDING OFFICIAL. ALL INFORMATION,
	DRAWINGS, SPECIFICATIONS AND ACCOMPANYING DATA SHALL
	BEAR THE NAME AND SIGNATURE OF THE PERSON RESPONSIBLE
	FOR THE DESIGN.

	2) SUBMIT A COPY OF THE SIGNED CONTRACT WITH THE
	COMPLETE SCOPE OF WORK SPECIFIED ON IT.

Review Stop	E			ELECTRICAL
Rev No	3	Status	P	Date	2015-06-24			Cont ID
Sent By	rmcdouga			Date	2015-06-24	Time	18:45	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-24	Time	15:23	Sent To

Notes

***NONE***

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2015-05-07			Cont ID
Sent By	rmcdouga			Date	2015-05-07	Time	18:01	Rev Time	0.00
Received By	rmcdouga			Date	2015-05-07	Time	16:46	Sent To

Notes

2015-05-07 17:32:02	PLAN
	REVIEW COMMENTS

	1ST REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	DENIED BY ELECTRICAL
	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) FBC107.1 GENERAL. SUBMITTAL DOCUMENTS CONSISTING OF
	CONSTRUCTION DOCUMENTS, STATEMENT OF SPECIAL
	INSPECTIONS, GEOTECHNICAL REPORT AND OTHER DATA SHALL
	BE SUBMITTED IN TWO OR MORE SETS WITH EACH PERMIT
	APPLICATION. THE CONSTRUCTION DOCUMENTS SHALL BE
	PREPARED BY A REGISTERED DESIGN PROFESSIONAL WHERE
	REQUIRED BY CHAPTER 471, FLORIDA STATUTES & 61G15
	FLORIDA ADMINISTRATIVE CODE OR CHAPTER 481, FLORIDA
	STATUTES & 61G1 FLORIDA ADMINISTRATIVE CODE.

	2) FBC 107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE DIMENSIONED AND DRAWN
	UPON SUITABLE MATERIAL. CONSTRUCTION DOCUMENTS SHALL BE
	OF SUFFICIENT CLARITY TO INDICATE THE LOCATION, NATURE
	AND EXTENT OF THE WORK PROPOSED AND SHOW IN DETAIL THAT
	IT WILL CONFORM TO THE PROVISIONS OF THIS CODE AND
	RELEVANT LAWS, ORDINANCES, RULES AND REGULATIONS, AS
	DETERMINED BY THE BUILDING OFFICIAL. SUCH DRAWINGS AND
	SPECIFICATIONS SHALL CONTAIN INFORMATION, IN THE FORM
	OF NOTES OR OTHERWISE, AS TO THE QUALITY OF MATERIALS,
	WHERE QUALITY IS ESSENTIAL TO CONFORMITY WITH THE
	TECHNICAL CODES. SUCH INFORMATION SHALL BE SPECIFIC,
	AND THE TECHNICAL CODES SHALL NOT BE CITED AS A WHOLE
	OR IN PART, NOR SHALL THE TERM "LEGAL" OR ITS
	EQUIVALENT BE USED AS A SUBSTITUTE FOR SPECIFIC
	INFORMATION. ALL INFORMATION, DRAWINGS, SPECIFICATIONS
	AND ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE
	OF THE PERSON RESPONSIBLE FOR THE DESIGN.

	3) FBC 107.2.1.4 QUALITY OF BUILDING PLANS. BUILDING
	PLANS SHALL BE DRAWN TO A MINIMUM 1/8 INCH SCALE UPON
	SUBSTANTIAL PAPER, CLOTH OR OTHER ACCEPTABLE MEDIUM.
	THIS POLICY MAY INCLUDE SUCH THINGS AS MINIMUM SIZE,
	SHAPE, CONTRAST, CLARITY, OR OTHER ITEMS RELATED TO
	RECORDS MANAGEMENT.

	4) FBC-R314.3.1 WHEN ALTERATIONS, REPAIRS OR ADDITIONS
	REQUIRING A PERMIT OCCUR, OR WHEN ONE OR MORE SLEEPING
	ROOMS ARE ADDED OR CREATED IN EXISTING DWELLINGS, THE
	INDIVIDUAL DWELLING UNIT SHALL BE EQUIPPED WITH SMOKE
	ALARMS LOCATED AS REQUIRED FOR NEW DWELLINGS.

	5) FBC- 107.3.5.3 - ELECTRIC SERVICE RISER WITH WIRE
	SIZES, CONDUIT DETAIL AND GROUNDING DETAIL. COMPLETE
	LOAD CALCULATIONS, PANEL SCHEDULES AND SHOW CIRCUITS ON
	FLOOR PLAN.

	6) NEC 110.9 - SPECIFY THE A.I.C. RATING OF THE
	ELECTRICAL EQUIPMENT ON THE PLANS.

	7) SPECIFY THE LOCATIONS OF THE ELECTRIC SERVICE METER
	AND PANELS ON THE ELECTRICAL PLANS. FBC 107.2.1

	8) NEC 210.11 (C) (3) AT LEAST ONE 20 - AMP BRANCH
	CIRCUIT SHALL BE PROVIDED TO SUPPLY BATHROOM RECEPTACLE
	OUTLETS.

	9) NEC 210.63 - PROVIDE A GFCI PROTECTED SERVICE OUTLET
	FOR WITHIN 25' OF MECHANICAL EQUIPMENT.

	10) NEC 406.8 - OUTDOOR RECEPTACLES ARE REQUIRED TO BE
	WEATHER PROOF.

	11) NEC 440.11 & 440.14 SHOW THE LOCATION OF THE
	REQUIRED A/C EQUIPMENT DISCONNECTING MEANS ON THE
	PLANS.

	12) NEC 210.52 (B) (3) - KITCHEN COUNTER TOP
	RECEPTACLES SHALL BE SUPPLIED BY NO FEWER THAN TWO
	SMALL APPLIANCE BRANCH CIRCUITS.

	13) NEC 210.12 (B) - OUTLETS ARE REQUIRED TO BE AFCI
	PROTECTED.

	14) NEC 406.11 - TAMPER-RESISTANT RECEPTACLES ARE
	REQUIRED.

	15) NEC 250.56 - SERVICE GROUNDING ELECTRODE TO BE
	AUGMENTED BY AN ADDITIONAL ELECTRODE 6 FEET AWAY OR
	PROVIDE EVIDENCE OF RESISTANCE TO GROUND OF 25 OHMS OR
	LESS.

	16) NEC 250.94 - INTERSYSTEM BONDING TERMINATION SHALL
	BE PROVIDED.

	17) NEC 210.52 (C) (1) - A RECEPTACLE OUTLET SHALL BE
	INSTALLED AT EACH COUNTERTOP SPACE 12 INCHES OR WIDER
	SO THAT NO POINT ALONG THE WALL LINE IS MORE THAN 2
	FEET MEASURED HORIZONTALLY FROM A RECEPTACLE OUTLET IN
	THAT SPACE.

	18) NEC 210.52(A) - (H) SHOW COMPLIANCE WITH REQUIRED
	RECEPTACLE OUTLET SPACING.

Review Stop	E			ELECTRICAL
Rev No	1	Status	N	Date	2015-01-20			Cont ID
Sent By	rmcdouga			Date	2015-01-20	Time	18:59	Rev Time	0.00
Received By	rmcdouga			Date	2015-01-20	Time	18:42	Sent To

Notes

2015-01-20 19:00:40	NO ELECTICAL PLANS WERE SUBMITTED. A SEPARATE PERMIT,
	APPLICATION AND PLAN REVIEW IS REQUIRED FOR ANY
	ELECTRICAL WORK.

Review Stop	I			INCOMING/PROCESSING
Rev No	4	Status	N	Date	2015-06-25			Cont ID
Sent By	rmcdouga			Date	2015-06-25	Time	17:56	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-25	Time	17:52	Sent To

Notes

***NONE***

Review Stop	I			INCOMING/PROCESSING
Rev No	3	Status	N	Date	2015-06-24			Cont ID
Sent By	rmcdouga			Date	2015-06-24	Time	19:01	Rev Time	0.00
Received By	rmcdouga			Date	2015-05-29	Time		Sent To	B

Notes

2015-06-18 12:45:19	05/29/2015. ROUTED TO R. MCDOUGAL'S DESK FOR BUILDING,
	MECHANICAL AND ELECRICAL REVIEWS. DAH

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2015-05-07			Cont ID
Sent By				Date	2015-05-07	Time		Rev Time	0.00
Received By	jgomez			Date	2015-04-07	Time	14:41	Sent To

Notes

2015-04-07 14:42:10

RE-SUBMITTAL SENT TO R24 SHELF FOR REVIEW. JG.

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2015-01-20			Cont ID
Sent By	rmcdouga			Date	2015-01-20	Time	19:00	Rev Time
Received By	rmcdouga			Date	2015-01-08	Time		Sent To

Notes

2015-01-09 09:13:08

INCOMING SENT TO R-14.

Review Stop	M			MECHANICAL (A/C)
Rev No	3	Status	P	Date	2015-06-25			Cont ID
Sent By	rmcdouga			Date	2015-06-25	Time	17:56	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-25	Time	17:56	Sent To

Notes

***NONE***

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2015-06-24			Cont ID
Sent By	rmcdouga			Date	2015-06-24	Time	19:00	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-24	Time	15:23	Sent To

Notes

2015-06-24 19:00:45	PLAN
	REVIEW COMMENTS

	2ND REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	DENIED BY MECHANICAL
	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) SPECIFY THE SIZE OF ALL SUPPLY AND RETURN DUCTS ON
	THE PLANS. FBC 107.2.1

	2) FBC - 107.3.5.3 PROVIDE TWO SETS OF A MECHANICAL
	PLAN TO SHOW EQUIPMENT AND LOCATION AND DUCT SYSTEMS
	PER FBC-R M16. SHOW CLOTHES DRYER AND BATH EXHAUST PER
	FBC-R M15.

	3) FBC-R - M1305.1.3 APPLIANCES IN ATTICS.
	ATTICS CONTAINING APPLIANCES SHALL BE PROVIDED WITH AN
	OPENING AND A CLEAR AND UNOBSTRUCTED PASSAGEWAY LARGE
	ENOUGH TO ALLOW REMOVAL OF THE LARGEST APPLIANCE, BUT
	NOT LESS THAN 30 INCHES (762 MM) HIGH AND 22 INCHES
	(559 MM) WIDE AND NOT MORE THAN 6 FEET (1829 MM) LONG
	MEASURED ALONG THE CENTERLINE OF THE PASSAGEWAY FROM
	THE OPENING TO THE APPLIANCE. THE PASSAGEWAY SHALL HAVE
	CONTINUOUS SOLID FLOORING IN ACCORDANCE WITH CHAPTER 5
	NOT LESS THAN 24 INCHES (610 MM) WIDE. A LEVEL SERVICE
	SPACE AT LEAST 30 INCHES (762 MM) DEEP AND 30 INCHES
	(762 MM) WIDE SHALL BE PRESENT ALONG ALL SIDES OF THE
	APPLIANCE WHERE ACCESS IS REQUIRED. THE CLEAR ACCESS
	OPENING DIMENSIONS SHALL BE A MINIMUM OF 20 INCHES BY
	30 INCHES (508 MM BY 762 MM), AND LARGE ENOUGH TO ALLOW
	REMOVAL OF THE LARGEST APPLIANCE.

	4) FBC-R - M 1602.4 PROVIDE BALANCED AIR RETURN AT
	BEDROOMS.

	5) FBC 107.2.1.4 QUALITY OF BUILDING PLANS. BUILDING
	PLANS SHALL BE DRAWN TO A MINIMUM 1/8 INCH SCALE UPON
	SUBSTANTIAL PAPER, CLOTH OR OTHER ACCEPTABLE MEDIUM.
	THIS POLICY MAY INCLUDE SUCH THINGS AS MINIMUM SIZE,
	SHAPE, CONTRAST, CLARITY, OR OTHER ITEMS RELATED TO
	RECORDS MANAGEMENT.

	6) FBC 107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE DIMENSIONED AND DRAWN
	UPON SUITABLE MATERIAL. CONSTRUCTION DOCUMENTS SHALL BE
	OF SUFFICIENT CLARITY TO INDICATE THE LOCATION, NATURE
	AND EXTENT OF THE WORK PROPOSED AND SHOW IN DETAIL THAT
	IT WILL CONFORM TO THE PROVISIONS OF THIS CODE AND
	RELEVANT LAWS, ORDINANCES, RULES AND REGULATIONS, AS
	DETERMINED BY THE BUILDING OFFICIAL. SUCH DRAWINGS AND
	SPECIFICATIONS SHALL CONTAIN INFORMATION, IN THE FORM
	OF NOTES OR OTHERWISE, AS TO THE QUALITY OF MATERIALS,
	WHERE QUALITY IS ESSENTIAL TO CONFORMITY WITH THE
	TECHNICAL CODES. SUCH INFORMATION SHALL BE SPECIFIC,
	AND THE TECHNICAL CODES SHALL NOT BE CITED AS A WHOLE
	OR IN PART, NOR SHALL THE TERM "LEGAL" OR ITS
	EQUIVALENT BE USED AS A SUBSTITUTE FOR SPECIFIC
	INFORMATION. ALL INFORMATION, DRAWINGS, SPECIFICATIONS
	AND ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE
	OF THE PERSON RESPONSIBLE FOR THE DESIGN.

	7) PROVIDE AN ANCHORING DETAIL FOR THE MECHANICAL
	EQUIPMENT THAT IS LOCATED ON THE EXTERIOR OF THE
	BUILDING. FBC-R M1307.2.1

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2015-05-07			Cont ID
Sent By	rmcdouga			Date	2015-05-07	Time	17:26	Rev Time	0.00
Received By	rmcdouga			Date	2015-05-07	Time	16:56	Sent To

Notes

2015-05-07 17:07:46	PLAN
	REVIEW COMMENTS

	1ST REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	DENIED BY MECHANICAL
	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) FBC-R - M1401.3 SIZING. HEATING AND COOLING
	EQUIPMENT SHALL BE SIZED BASED ON BUILDING LOADS
	CALCULATED IN ACCORDANCE WITH ACCA MANUAL J OR OTHER
	APPROVED HEATING AND COOLING CALCULATION METHODOLOGIES.
	PROVIDE EQUIPMENT SIZING CALCULATIONS.

	2) FBC - 107.3.5.3 PROVIDE TWO SETS OF A MECHANICAL
	PLAN TO SHOW EQUIPMENT AND LOCATION AND DUCT SYSTEMS
	PER FBC-R M16. SHOW CLOTHES DRYER AND BATH EXHAUST PER
	FBC-R M15.

	3) FBC-R - M1305.1.3 APPLIANCES IN ATTICS.
	ATTICS CONTAINING APPLIANCES SHALL BE PROVIDED WITH AN
	OPENING AND A CLEAR AND UNOBSTRUCTED PASSAGEWAY LARGE
	ENOUGH TO ALLOW REMOVAL OF THE LARGEST APPLIANCE, BUT
	NOT LESS THAN 30 INCHES (762 MM) HIGH AND 22 INCHES
	(559 MM) WIDE AND NOT MORE THAN 6 FEET (1829 MM) LONG
	MEASURED ALONG THE CENTERLINE OF THE PASSAGEWAY FROM
	THE OPENING TO THE APPLIANCE. THE PASSAGEWAY SHALL HAVE
	CONTINUOUS SOLID FLOORING IN ACCORDANCE WITH CHAPTER 5
	NOT LESS THAN 24 INCHES (610 MM) WIDE. A LEVEL SERVICE
	SPACE AT LEAST 30 INCHES (762 MM) DEEP AND 30 INCHES
	(762 MM) WIDE SHALL BE PRESENT ALONG ALL SIDES OF THE
	APPLIANCE WHERE ACCESS IS REQUIRED. THE CLEAR ACCESS
	OPENING DIMENSIONS SHALL BE A MINIMUM OF 20 INCHES BY
	30 INCHES (508 MM BY 762 MM), AND LARGE ENOUGH TO ALLOW
	REMOVAL OF THE LARGEST APPLIANCE.

	4) FBC-R - M 1602.4 PROVIDE BALANCED AIR RETURN AT
	BEDROOMS.

	5) FBC 107.2.1.4 QUALITY OF BUILDING PLANS. BUILDING
	PLANS SHALL BE DRAWN TO A MINIMUM 1/8 INCH SCALE UPON
	SUBSTANTIAL PAPER, CLOTH OR OTHER ACCEPTABLE MEDIUM.
	THIS POLICY MAY INCLUDE SUCH THINGS AS MINIMUM SIZE,
	SHAPE, CONTRAST, CLARITY, OR OTHER ITEMS RELATED TO
	RECORDS MANAGEMENT.

	6) FBC 107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE DIMENSIONED AND DRAWN
	UPON SUITABLE MATERIAL. CONSTRUCTION DOCUMENTS SHALL BE
	OF SUFFICIENT CLARITY TO INDICATE THE LOCATION, NATURE
	AND EXTENT OF THE WORK PROPOSED AND SHOW IN DETAIL THAT
	IT WILL CONFORM TO THE PROVISIONS OF THIS CODE AND
	RELEVANT LAWS, ORDINANCES, RULES AND REGULATIONS, AS
	DETERMINED BY THE BUILDING OFFICIAL. SUCH DRAWINGS AND
	SPECIFICATIONS SHALL CONTAIN INFORMATION, IN THE FORM
	OF NOTES OR OTHERWISE, AS TO THE QUALITY OF MATERIALS,
	WHERE QUALITY IS ESSENTIAL TO CONFORMITY WITH THE
	TECHNICAL CODES. SUCH INFORMATION SHALL BE SPECIFIC,
	AND THE TECHNICAL CODES SHALL NOT BE CITED AS A WHOLE
	OR IN PART, NOR SHALL THE TERM "LEGAL" OR ITS
	EQUIVALENT BE USED AS A SUBSTITUTE FOR SPECIFIC
	INFORMATION. ALL INFORMATION, DRAWINGS, SPECIFICATIONS
	AND ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE
	OF THE PERSON RESPONSIBLE FOR THE DESIGN.

	7) PROVIDE AN EQUIPMENT SCHEDULE ON THE PLANS THAT
	CORRESPONDS WITH THE EQUIPMENT SIZING CALCULATIONS. FBC
	107.2.1

	8) PROVIDE AN ANCHORING DETAIL FOR THE MECHANICAL
	EQUIPMENT THAT IS LOCATED ON THE EXTERIOR OF THE
	BUILDING. FBC-R M1307.2.1

Review Stop	P			PLUMBING
Rev No	3	Status	P	Date	2015-06-24			Cont ID
Sent By	tlarge			Date	2015-06-24	Time	19:03	Rev Time	0.00
Received By	rmcdouga			Date	2015-06-24	Time	19:03	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	2	Status	P	Date	2015-05-07			Cont ID
Sent By	tklarge			Date	2015-05-07	Time	10:04	Rev Time	0.00
Received By	tklarge			Date	2015-05-07	Time	09:47	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2015-01-20			Cont ID
Sent By	tklarge			Date	2015-01-20	Time	03:49	Rev Time	0.00
Received By	tklarge			Date	2015-01-20	Time	03:36	Sent To

Notes

2015-01-20 03:49:21	1) THE PLANS ARE VAGUE AS TO THE EXTENT OF PLUMBING
	WORK THAT IS TO BE DONE. CLARIFY "BATHROOM REMODELING".
	ARE THE BATHROOM FIXTURES BEING REPLACED IN THE SAME
	LOCATION? INDICATE IF THERE ARE BATHTUBS OR SHOWERS IN
	THE BATHROOMS AND IF THEY ARE BEING REPLACED.WPB AMEND.
	TO 2010 FBC SEC.107.2.1.
	2) CLEARLY IDENTIFY THE BATHROOMS ON THE FLOOR PLAN.
	WPB AMEND. TO 2010 FBC SEC.107.2.1.
	3) INDICATE ON THE PLANS IF THE KITCHEN SINK IS GOING
	TO BE REPLACED.

	PLUMBING PLAN REVIEW
	TIM LARGE
	CHIEF PLUMBING INSPECTOR
	561-805-6692
	[email protected]