City of West Palm Beach eGovPlus

Plan Review Details - Permit 14080942

Plan Review Stops For Permit 14080942

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	4	Status	P	Date	2015-03-25			Cont ID
Sent By	tklarge			Date	2015-03-25	Time	08:18	Rev Time	0.00
Received By	rmcdouga			Date	2015-03-25	Time	09:39	Sent To

Notes

***NONE***

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	3	Status	F	Date	2015-03-09			Cont ID
Sent By	rmcdouga			Date	2015-03-09	Time	18:13	Rev Time	0.00
Received By	rmcdouga			Date	2015-03-09	Time	18:13	Sent To	E

Notes

2015-03-09 17:52:41	3RD REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	1) ON SHEET SP-1 THE OCCUPANCY TYPE IS INCORRECTLY
	SPECIFIED AS R-3. THIS STRUCTURE IS A DETACHED PRIVATE
	GARAGE THAT IS BEING CONVERTED TO A UTILITY SPACE.
	BASED ON THE PLANS THIS IS NON-HABITABLE SPACE. IT IS A
	GROUP U OCCUPANCY. FBC 312

	2) ON SHEET SP-1 THE CONSTRUCTION TYPE IS SPECIFIED AS
	TYPE V AND IT SHOULD BE TYPE V-B. FBC 601

	3) THE PRODUCT APPROVAL THAT WAS SUBMITTED FOR THE
	STORM PANELS HAS CONFLICTING INFORMATION MARKED. THE
	DIRECT MOUNT INSTALLATION ( SECTION 8) WAS SELECTED ON
	SHEET 4 OF 15. THIS SYSTEM CAN NOT BE USED WITH THE
	TAPCON ANCHORS THAT IS MARKED ON SHEET 10 OF 13. THE
	ANCHORS REQUIRED FOR THIS SYSTEM IS PANELMATES,
	CALK-IN, SOLID SET OR CF TAP-GRIP.

	4) THE VALUE OF $1800.00 IS TOO LOW FOR THIS SCOPE OF
	WORK. ALL OF THE WORK THAT WAS DONE TO THE EXISTING
	GARAGE WITHOUT PERMITS OR INSPECTIONS IS REQUIRED TO BE
	INCLUDED IN THE VALUE ( TOTAL REPLACEMENT COST). FBC
	109.3 BUILDING PERMIT VALUATION. FOR PERMITTING
	PURPOSES, VALUATION OF BUILDINGS AND SYSTEMS SHALL BE
	TOTAL REPLACEMENT VALUE TO INCLUDE STRUCTURAL,
	ELECTRIC, PLUMBING, MECHANICAL, INTERIOR FINISH,
	RELATIVE SITE WORK, ARCHITECTURAL AND DESIGN FEES,
	MARKETING COSTS, OVERHEAD AND PROFIT; EXCLUDING ONLY
	LAND VALUE. VALUATION REFERENCES MAY INCLUDE THE LATEST
	PUBLISHED DATA OF NATIONAL CONSTRUCTION COST ANALYSIS
	SERVICES (MARSHALL-SWIFT, MEANS, ETC.), AS PUBLISHED BY
	INTERNATIONAL CODE CONGRESS. FINAL BUILDING PERMIT
	VALUATION SHALL BE SET BY THE BUILDING OFFICIAL.

	IN ORDER TO REDUCE PLAN REVIEW TIMES AND PROVIDE
	CLARIFICATION, PLEASE SUBMIT A RESPONSE LETTER
	INDICATING HOW EACH OF THE REVIEW COMMENTS HAS BEEN
	ADDRESSED.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2015-01-08			Cont ID
Sent By	rmcdouga			Date	2015-01-08	Time	10:57	Rev Time	0.00
Received By	rmcdouga			Date	2015-01-08	Time	10:19	Sent To

Notes

2015-01-08 10:57:17	2ND REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	BUILDING

	THE PLANS THAT WERE RESUBMITTED INDICATE THAT THE
	STRUCTURE WILL BE USED AS A STORAGE/UTILITY ROOM. THIS
	IS NOT CONSIDERED A CHANGE OF OCCUPANCY FROM A GARAGE.
	THEREFORE, ONLY THE IMPROVEMENTS THAT WERE DONE WITHOUT
	PERMITS AND INSPECTIONS WILL NEED TO BE ADDRESSED. I
	COULD NOT LOCATE ANY RECORDS THAT INDICATE THAT THE
	WORK TO ADD THE BATHROOM, UTILITY SINK OR TANKLESS GAS
	WATER HEATER TO THE GARAGE WAS DONE WITH THE REQUIRED
	PERMITS AND INSPECTIONS. UNLESS YOU CAN PROVIDE
	DOCUMENTATION THAT THE WORK WAS PERMITTED AND
	INSPECTED, THE WORK WILL BE REQUIRED TO COMPLY WITH THE
	2010 FBC AND 2008 NEC. ALL OF THE WORK IS REQUIRED TO
	BE PERMITTED AND INSPECTED. YOU CAN CONTACT DIANNE
	FULCHER VIA EMAIL AT [email protected] IF YOU WISH TO
	MAKE A RESEARCH REQUEST. SEE ZONING COMMENTS.

	1) FBC 107.2.1 - INFORMATION ON CONSTRUCTION DOCUMENTS.
	ALL INFORMATION, DRAWINGS, SPECIFICATIONS AND
	ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE OF
	THE PERSON RESPONSIBLE FOR THE DESIGN.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2014-09-13			Cont ID
Sent By	rmcdouga			Date	2014-09-13	Time	09:48	Rev Time	0.00
Received By	rmcdouga			Date	2014-09-13	Time	08:05	Sent To	P

Notes

2014-09-13 09:09:25	PLAN REVIEW COMMENTS


	1ST REVIEW: FBC 2010
	ROBERT MCDOUGAL, CBO
	COMMERCIAL COMBINATION PLANS EXAMINER
	(561) 805-6714
	[email protected]

	PLEASE ADDRESS THE ITEMS NOTED BELOW:

	BUILDING

	THE CITY RECORDS INDICATE THAT THE STRUCTURE SHOWN ON
	THE DRAWINGS IS A DETACHED GARAGE. I COULD NOT LOCATE
	ANY RECORDS THAT INDICATE THAT THE WORK TO ADD THE
	BATHROOM, KITCHEN SINK OR TANKLESS GAS WATER HEATER TO
	THE GARAGE WAS DONE WITH THE REQUIRED PERMITS AND
	INSPECTIONS. IT APPEARS THAT THE DETACHED GARAGE WAS
	CONVERTED TO HABITABLE SPACE WITHOUT PERMITS. UNLESS
	YOU CAN PROVIDE DOCUMENTATION THAT THE WORK WAS
	PERMITTED AND INSPECTED, THE STRUCTURE WILL BE REQUIRED
	TO BE RETURNED TO A GARAGE OR BE BROUGHT INTO
	COMPLIANCE WITH THE 2010 FBC AS A CHANGE OF OCCUPANCY
	FROM A GARAGE TO AN OFFICE (PENDING ZONING APPROVAL).
	ALL OF THE WORK IS REQUIRED TO BE PERMITTED AND
	INSPECTED. YOU CAN CONTACT DIANNE FULCHER VIA EMAIL AT
	[email protected] IF YOU WISH TO MAKE A RESEARCH
	REQUEST. SEE ZONING COMMENTS.

	THESE COMMENTS WILL NEED TO BE ADDRESSED IF THE
	STRUCTURE IS TO BE CONVERTED FROM A GARAGE TO A
	HABITABLE SPACE.

	1) FBC 107.2.1 - INFORMATION ON CONSTRUCTION DOCUMENTS.
	ALL INFORMATION, DRAWINGS, SPECIFICATIONS AND
	ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE OF
	THE PERSON RESPONSIBLE FOR THE DESIGN.

	2) FBC 107.2.1.4 QUALITY OF BUILDING PLANS. BUILDING
	PLANS SHALL BE DRAWN TO A MINIMUM 1/8 INCH SCALE UPON
	SUBSTANTIAL PAPER, CLOTH OR OTHER ACCEPTABLE MEDIUM.
	THIS POLICY MAY INCLUDE SUCH THINGS AS MINIMUM SIZE,
	SHAPE, CONTRAST, CLARITY, OR OTHER ITEMS RELATED TO
	RECORDS MANAGEMENT.

	3) FBC EXISTING BUILDING 912.6.1 EXTERIOR WALL RATING
	FOR CHANGE OF OCCUPANCY CLASSIFICATION TO A HIGHER
	HAZARD CATEGORY.
	WHEN A CHANGE OF OCCUPANCY GROUP IS MADE TO A HIGHER
	HAZARD CATEGORY AS SHOWN IN TABLE 912.6, EXTERIOR WALLS
	SHALL HAVE FIRE RESISTANCE AND EXTERIOR OPENING
	PROTECTIVES AS REQUIRED BY THE FLORIDA BUILDING CODE,
	BUILDING. SUBMIT TWO COPIES OF A SURVEY SHOWING THE
	LOCATION OF THE STRUCTURES ON THE PROPERTY.

	4) FBC EXISTING BUILDING 912.6.3 OPENINGS IN EXTERIOR
	WALLS SHALL BE PROTECTED AS REQUIRED BY THE FLORIDA
	BUILDING CODE, BUILDING. WHERE OPENINGS IN THE EXTERIOR
	WALLS ARE REQUIRED TO BE PROTECTED BECAUSE OF THEIR
	DISTANCE FROM THE PROPERTY LINE, THE SUM OF THE AREA OF
	SUCH OPENINGS SHALL NOT EXCEED 50 PERCENT OF THE TOTAL
	AREA OF THE WALL IN EACH STORY.


	5) FBC EXISTING BUILDING 907.2 WIND LOADS.
	BUILDINGS AND STRUCTURES SUBJECT TO A CHANGE OF
	OCCUPANCY WHERE SUCH CHANGE IN THE NATURE OF OCCUPANCY
	RESULTS IN A HIGHER RISK CATEGORY BASED ON THE FLORIDA
	BUILDING CODE, BUILDING TABLE 1604.5, SHALL BE ANALYZED
	AND SHALL COMPLY WITH THE APPLICABLE WIND LOAD
	PROVISIONS OF THE FLORIDA BUILDING CODE, BUILDING.

	6) FBC EXISTING BUILDING 911.1 LIGHT AND VENTILATION.
	LIGHT AND VENTILATION SHALL COMPLY WITH THE
	REQUIREMENTS OF THE FLORIDA BUILDING CODE, BUILDING FOR
	THE NEW OCCUPANCY.

	7) SHOW COMPLIANCE WITH 2010 FBC ENERGY CONSERVATION
	SECT. 101.4.3 & 103.2 BY SUBMITTING THE PROPER
	CONSTRUCTION DOCUMENTS. SEE RESIDENTIAL BUILDING FORMS
	402 OR 405.

	8) FBC EXISTING BUILDING 912.4.1 MEANS OF EGRESS FOR
	CHANGE TO HIGHER HAZARD CATEGORY.
	WHEN A CHANGE OF OCCUPANCY CLASSIFICATION IS MADE TO A
	HIGHER HAZARD CATEGORY, THE MEANS OF EGRESS SHALL
	COMPLY WITH THE REQUIREMENTS OF CHAPTER 10 OF THE
	FLORIDA BUILDING CODE, BUILDING.

	9) PLANS REQUIRE REVIEW BY THE PBC IMPACT FEE OFFICE.
	CALL 233-5025. UPON APPROVAL, YOU MAY CHECK OUT ONE
	PLAN AND TAKE TO THAT OFFICE FOR REVIEW. PLEASE
	RETURNED STAMPED WITH A COPY OF RECEIPT AS APPLICABLE.

	10) THE DESCRIPTION OF WORK AND VALUATION ON THE
	APPLICATION WILL NEED TO BE REVISED TO REFLECT THE
	SCOPE OF WORK. FBC 109.3

	IN ORDER TO REDUCE PLAN REVIEW TIMES, PLEASE SUBMIT A
	RESPONSE LETTER INDICATING HOW EACH OF THE REVIEW
	COMMENTS HAS BEEN ADDRESSED.

Review Stop	E			ELECTRICAL
Rev No	3	Status	P	Date	2015-03-12			Cont ID
Sent By	dhayes			Date	2015-03-12	Time	09:38	Rev Time	0.00
Received By	dhayes			Date	2015-03-12	Time	09:33	Sent To

Notes

***NONE***

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2015-01-08			Cont ID
Sent By	dhayes			Date	2015-01-08	Time	11:03	Rev Time	0.00
Received By	dhayes			Date	2015-01-08	Time	11:03	Sent To

Notes

2015-01-08 11:03:18	DATE: 01/08/2015
	PROJECT: PARADELO
	PERMIT#: 14080942
	CODE: 2008 EDITION OF THE NEC
	2010 EDITION OF THE FBC
	2010 WPB AMENDMENTS TO THE FBC, CHAPTER 1,
	ADMINISTRATION, 2012 FBC SUPPLEMENTS.

	2ND ELECTRICAL PLAN REVIEW
	ACTION: DENIED

	AS CLEARLY INDICATED IN THE PREVIOUS REVIEWS, THE CITY
	RECORDS INDICATE THAT THE STRUCTURE SHOWN ON THE
	DRAWINGS IS A DETACHED GARAGE. NO RECORDS COULD BE
	LOCATED TO INDICATE THE BATHROOM, KITCHEN, OR TANKLESS
	GAS WATER HEATER WERE ADDED TO THE GARAGE WITH THE
	REQUIRED PERMITS AND INSPECTIONS. SEE BUILDING,
	PLUMBING AND ZONING COMMENTS. ASIDE FROM THE BUILDING
	AND ZONING COMMENTS, THERE ARE SERVERE DESIGN FLAWS
	THROUGHOUT THE ELECTRICAL PLAN SUBMITTED. COSIDER
	CONSULTING WITH A DESIGN PROFESSIONAL FOR SOME
	ASSISTANCE IN COMPLETING THIS OVERALL DESIGN.
	PROVIDED IT IS ALLOWED BY BUILDING, PLUMBING AND ZONING
	AND IN ORDER TO MAKE THE CONVERSION MEET CURRENT
	ELECTRICAL CODE THE FOLLOWING COMMENTS WOULD NEED TO BE
	ADDRESSED:

	1) SUFFICIENT CLEAR ACCESS AND DEDICATED WORKING SPACE
	SHALL BE PROVIDED AND MAINTAINED ABOUT ALL ELECTRICAL
	EQUIPMENT TO ALLOW READY AND SAFE OPERATION AND
	MAINTENANCE OF SUCH EQUIPMENT. NEC 110.26 THE KITCHEN
	COUNTER TOP, REFRIGERATOR, DRYER, AND TANKLESS WATER
	HEATER APPEAR TO BE ENCROACHING ON THE REQUIRED WORKING
	CLEARANCES DESCRIBED IN THE NEC 110.26.

	2) THE SERVICE DISCONNECTING MEANS SHALL BE INSTALLED
	AT A READILY ACCESSIBLE LOCATION EITHER OUTSIDE OF A
	BUILDING OR STRUCTURE OR INSIDE NEAREST THE POINT OF
	ENTRANCE OF THE SERVICE CONDUCTORS. NEC 230.70(A)(1)
	INDICATE THE LOCATION OF THE ELECTRICAL SERVICE AND THE
	FEED TO THE PANEL IN THE GARAGE.THE SUB PANEL AT THE
	UTILITY STRUCTURE IS INDICATED TO BE FED FROM THE HOUSE
	PANEL WITH A 50AMP BREAKER ON #1 WIRE WITH A 175AMP
	TOTAL CONNECTED LOAD INDICATED AT THE SUB PANEL WITH A
	100AMP MAIN BREAKER.

	3) PROVIDE A REVISED RISER DIAGRAM, LOAD CALCULATION
	AND PANEL DIRECTORIES SHOWING COMPLETE FEEDER DETAILS
	AREA IN SQUARE FEET OF THE BUILDING, THE TOTAL
	CALCULATED LOAD BEFORE APPLYING DEMAND FACTORS, THE
	DEMAND FACTORS USED, THE CALCULATED LOAD AFTER APPLYING
	DEMAND FACTORS, AND THE SIZE AND TYPE OF CONDUCTORS TO
	BE USED. NEC 215.5 THE RISER DIAGRAM SUBMITTED DOES NOT
	ADAQUATELY MEET THE MINIMUM DESIGN CRITERIA REQUIRED.
	PROVIDE THE GROUNDING ELECTRODE DETAIL, THE UTILITY
	METERING, SUBMITTALS ON THE GENERATOR AND MTS, A
	REVISED DESIGN IS REQUIRED ON THE RISER TO INDICATE HOW
	THE MTS AND GENERATOR WILL PROVIDE OPTIONAL STANDBY
	POWER FOR THE SERVICE WITHOUT A BACKFEED. THE LOADS
	CALCULATED ON THE PLAN INDICATE A TOTAL OF 415 AMPS
	WITH A 200 AMP MAIN AND A 2/0 FEEDER. THE SUB PANEL AT
	THE UTILITY STRUCTURE IS INDICATED TO BE FED FROM THE
	HOUSE PANEL WITH A 50AMP BREAKER ON #1 WIRE WITH A
	175AMP TOTAL CONNECTED LOAD INDICATED AT THE SUB PANEL.

	4) EVERY CIRCUIT AND CIRCUIT MODIFICATION SHALL BE
	LEGIBLY IDENTIFIED AS TO ITS CLEAR, EVIDENT, AND
	SPECIFIC PURPOSE OR USE. NEC 408.4 PROVIDE REVISED
	PANEL SCHEDULES.THE PANEL SCHEDULES DO NOT ADAQUATELY
	INDICATE ALL REQUIRED CIRCUITRY OR SHOW ALL CIRCUITRY
	USED ON THE PLAN. THE PANEL SCHEDULE MUST COINCIDE WITH
	THE CIRCUITRY ON THE FLOOR PLAN. NOT ALL CIRCUITS ON
	THE FLOOR PLAN ARE INDICATED IN THE PANEL SCHEDULE.

	5) ALL GROUNDING ELECTRODES AS DESCRIBED IN
	250.52(A)(1) THROUGH (A)(7) THAT ARE PRESENT AT EACH
	BUILDING OR STRUCTURE SERVED SHALL BE BONDED TOGETHER
	TO FORM THE GROUNDING ELECTRODE SYSTEM. NEC 250.50

	6) WHERE INSTALLED IN OR ATTACHED TO A BUILDING OR
	STRUCTURE, A METAL PIPING SYSTEM(S), INCLUDING GAS
	PIPING, THAT IS LIKELY TO BECOME ENERGIZED SHALL BE
	BONDED TO THE SERVICE EQUIPMENT ENCLOSURE, THE GROUNDED
	CONDUCTOR AT THE SERVICE, THE GROUNDING ELECTRODE
	CONDUCTOR WHERE OF SUFFICIENT SIZE, OR THE ONE OR MORE
	GROUNDING ELECTRODES USED NEC 250.104(3)(B)

	7) THE CONNECTION OF A GROUNDING ELECTRODE CONDUCTOR AT
	EACH BUILDING OR STRUCTURE WHERE SUPPLIED BY A
	FEEDER(S) OR BRANCH CIRCUIT(S), SHALL BE MADE AS
	SPECIFIED 250.32, 250.68(A) AND (B).

	8) THE VALUE OF THE PROJECT ISN?T REALISTIC AND WILL BE
	REVISED TO INCLUDE THE OVERALL SCOPE OF WORK. FBC WPB
	AMENDMENTS. SECTION 109.3

	9) THE PLAN IS STILL NOT SIGNED BY THE DESIGNER. ALL
	INFORMATION, DRAWINGS, SPECIFICATIONS AND ACCOMPANYING
	DATA SHALL BEAR THE NAME AND SIGNATURE OF THE PERSON
	RESPONSIBLE FOR THE DESIGN. WPB AMENDMENTS TO FBC
	107.2.1

	10) A SEPARATE ELECTRICAL PERMIT APPLICATION IS STILL
	REQUIRED WITH THE SUBMITTAL FOR THE ISSUANCE OF AN
	ELCTRICAL PERMIT FOR THE INSTALLATION OF PROPOSED
	ELECTRICAL SCOPE.

	11) A SEPARATE ELECTRICAL PERMIT APPLICATION
	ACCOMPANIED BY THE MANUFACTURER PRODUCT APPROVAL
	DOCUMENTATION IS REQUIRED FOR THE GENERATOR AND MTS.

	WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RE-SUBMITTAL FORM. SEE LINK:
	HTTP://WPB.ORG/DEVELOPMENT/WP-CONTENT/UPLOADS/SITES/33/
	2013/09/APPLICATION_RESUBMITTAL_FORM_04132010.PDF

	ADDITIONALLY, PLEASE INSERT CORRECTED PAGES INTO
	SUBMITTAL PACKAGE AND LEAVE THE PREVIOUSLY REVIEWED
	SHEETS FOR COMPARATIVE REVIEW.

	DAVID HAYES, ELECTRICAL PLANS EXAMINER, PX3421,
	561-805-6717 OR [email protected]

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2014-09-17			Cont ID
Sent By	dhayes			Date	2014-09-17	Time	08:16	Rev Time	0.00
Received By	dhayes			Date	2014-09-17	Time	08:16	Sent To

Notes

2014-09-17 08:21:46	DATE: 9/17/2014
	PROJECT:
	PERMIT#:
	CODE: 2008 EDITION OF THE NEC
	2010 EDITION OF THE FBC
	2010 WPB AMENDMENTS TO THE FBC, CHAPTER 1,
	ADMINISTRATION, 2012 FBC SUPPLEMENTS.

	1ST ELECTRICAL PLAN REVIEW
	ACTION: DENIED

	AS CLEARLY INDICATED IN THE PREVIOUS REVIEWS, THE CITY
	RECORDS INDICATE THAT THE STRUCTURE SHOWN ON THE
	DRAWINGS IS A DETACHED GARAGE. NO RECORDS COULD BE
	LOCATED TO INDICATE THE BATHROOM, KITCHEN, OR TANKLESS
	GAS WATER HEATER WERE ADDED TO THE GARAGE WITH THE
	REQUIRED PERMITS AND INSPECTIONS. SEE BUILDING,
	PLUMBING AND ZONING COMMENTS.
	PROVIDED IT IS ALLOWED BY BUILDING, PLUMBING AND ZONING
	AND IN ORDER TO MAKE THE CONVERSION MEET CURRENT
	ELECTRUCAL CODE THE FOLLOWING COMMENTS WOULD NEED TO BE
	ADDRESSED:

	1) SUFFICIENT CLEAR ACCESS AND DEDICATED WORKING SPACE
	SHALL BE PROVIDED AND MAINTAINED ABOUT ALL ELECTRICAL
	EQUIPMENT TO ALLOW READY AND SAFE OPERATION AND
	MAINTENANCE OF SUCH EQUIPMENT. NEC 110.26 THE KITCHEN
	COUTER TOP, REFRIDGERATOR, DRYER, AND TANKLESS WATER
	HEATER APPEAR TO BE ENCHROCHING ON THE REQUIRED WORKING
	CLEARANCES DESCRIBED IN THE NEC 110.26.

	2) BRANCH CIRCUITS FOR LIGHTING AND FOR APPLIANCES,
	INCLUDING MOTOR-OPERATED APPLIANCES, SHALL BE PROVIDED
	TO SUPPLY THE LOADS CALCULATED IN ACCORDANCE WITH
	220.10. IN ADDITION, BRANCH CIRCUITS SHALL BE PROVIDED
	FOR SPECIFIC LOADS NOT COVERED BY 220.10 WHERE REQUIRED
	ELSEWHERE IN THIS CODE AND FOR DWELLING UNIT LOADS AS
	SPECIFIED IN THE NEC 210.11(C).
	(A) NUMBER OF BRANCH CIRCUITS. THE MINIMUM NUMBER OF
	BRANCH CIRCUITS SHALL BE DETERMINED FROM THE TOTAL
	CALCULATED LOAD AND THE SIZE OR RATING OF THE CIRCUITS
	USED. IN ALL INSTALLATIONS, THE NUMBER OF CIRCUITS
	SHALL BE SUFFICIENT TO SUPPLY THE LOAD SERVED. IN NO
	CASE SHALL THE LOAD ON ANY CIRCUIT EXCEED THE MAXIMUM
	SPECIFIED BY 220.18.
	(B) LOAD EVENLY PROPORTIONED AMONG BRANCH CIRCUITS.
	WHERE THE LOAD IS CALCULATED ON THE BASIS OF
	VOLT-AMPERES PER SQUARE METER OR PER SQUARE FOOT, THE
	WIRING SYSTEM UP TO AND INCLUDING THE BRANCH-CIRCUIT
	PANELBOARD(S) SHALL BE PROVIDED TO SERVE NOT LESS THAN
	THE CALCULATED LOAD. THIS LOAD SHALL BE EVENLY
	PROPORTIONED AMONG MULTIOUTLET BRANCH CIRCUITS WITHIN
	THE PANELBOARD(S). BRANCH-CIRCUIT OVERCURRENT DEVICES
	AND CIRCUITS SHALL BE REQUIRED TO BE INSTALLED ONLY TO
	SERVE THE CONNECTED LOAD.
	(C) SMALL-APPLIANCE BRANCH CIRCUITS. IN ADDITION TO THE
	NUMBER OF BRANCH CIRCUITS REQUIRED BY OTHER PARTS OF
	THIS SECTION, TWO OR MORE 20-AMPERE SMALL-APPLIANCE
	BRANCH CIRCUITS SHALL BE PROVIDED FOR ALL RECEPTACLE
	OUTLETS SPECIFIED BY 210.52(B).
	(D) LAUNDRY BRANCH CIRCUITS. IN ADDITION TO THE NUMBER
	OF BRANCH CIRCUITS REQUIRED BY OTHER PARTS OF THIS
	SECTION, AT LEAST ONE ADDITIONAL 20-AMPERE BRANCH
	CIRCUIT SHALL BE PROVIDED TO SUPPLY THE LAUNDRY
	RECEPTACLE OUTLET(S) REQUIRED BY 210.52(F). THIS
	CIRCUIT SHALL HAVE NO OTHER OUTLETS.
	(E) BATHROOM BRANCH CIRCUITS. IN ADDITION TO THE NUMBER
	OF BRANCH CIRCUITS REQUIRED BY OTHER PARTS OF THIS
	SECTION, AT LEAST ONE 20-AMPERE BRANCH CIRCUIT SHALL BE
	PROVIDED TO SUPPLY BATHROOM RECEPTACLE OUTLET(S). SUCH
	CIRCUITS SHALL HAVE NO OTHER OUTLETS.

	3) WHEN ALTERATIONS, REPAIRS, OR ADDITIONS REQUIRING A
	PERMIT OCCUR, OR WHEN ONE OR MORE SLEEPING ROOMS ARE
	ADDED OR CREATED IN EXISTING DWELLINGS, THE INDIVIDUAL
	DWELLING UNIT SHALL BE EQUIPPED WITH SMOKE ALARMS
	LOCATED AS REQUIRED FOR NEW DWELLINGS. FBC-RESIDENTIAL
	314 AND 315.

	4) VERIFY THE WATER HEATER HAS THE REQUIRED ELECTRIC
	DISCONNECT. NEC 422.31

	5) THE SERVICE DISCONNECTING MEANS SHALL BE INSTALLED
	AT A READILY ACCESSIBLE LOCATION EITHER OUTSIDE OF A
	BUILDING OR STRUCTURE OR INSIDE NEAREST THE POINT OF
	ENTRANCE OF THE SERVICE CONDUCTORS. NEC 230.70(A)(1)
	INDICATE THE LOCATION OF THE ELECTRICAL SERVICE AND THE
	FEED TO THE PANEL IN THE GARAGE.

	6) PROVIDE A RISER DIAGRAM SHOWING FEEDER DETAILS.
	INCLUDE THE AREA IN SQUARE FEET OF THE BUILDING, THE
	TOTAL CALCULATED LOAD BEFORE APPLYING DEMAND FACTORS,
	THE DEMAND FACTORS USED, THE CALCULATED LOAD AFTER
	APPLYING DEMAND FACTORS, AND THE SIZE AND TYPE OF
	CONDUCTORS TO BE USED. NEC 215.5

	7) PROVIDE A COMPLETE LOAD CALCULATION. PROVIDE A PANEL
	SCHEDULE SHOWING ALL LOADS BALANCED. INDICATE THE
	PROPOSED WIRING METHOD, WIRE SIZE WITH OVER CURRENT
	PROTECTION FOR ALL CIRCUITS. NEC 220.12, 220.14, 230.31

	8) ALL NEW GENERAL PURPOSE OUTLETS MUST BE AFCI
	PROTECTED. NEC 210.12 NEW RECEPTACLES MUST BE TAMPER
	RESISTANT. NEC 406.11

	9) THE CONNECTION OF A GROUNDING ELECTRODE CONDUCTOR AT
	EACH BUILDING OR STRUCTURE WHERE SUPPLIED BY A
	FEEDER(S) OR BRANCH CIRCUIT(S), SHALL BE MADE AS
	SPECIFIED IN THE 2008 EDITION OF THE NEC ARTICLE
	250.68(A) AND (B).

	10) ALL 125V SINGLE PHASE, 15 AND 20AMP RECEPTACLES
	INSTALLED IN THE LOCATIONS SPECIFIED IN (1) THROUGH (8)
	SHALL HAVE GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
	FOR PERSONNEL. NEC 210.8. ALL OUTLETS IN THE KITCHEN
	SHALL BE GFCI PROTECTED.

	11) ARC-FAULT PROTECTION IS NOW REQUIRED IN RESIDENTIAL
	OCCUPANCIES ON ALL 15 AND 20 AMP BRANCH CIRCUITS THAT
	ARE NOT ALREADY REQUIRED TO BE PROTECTED BY GROUND
	FAULT INTERRUPTERS CIRCUITS (GFCI) OR OVER 120 VOLTS
	210.12(B)

	12) MULTI-WIRE BRANCH CIRCUITS THAT SHARE A COMMON
	GROUND CONDUCTOR (NEUTRAL) MUST SHARE A COMMON
	DISCONNECT OR THE NEUTRALS MUST BE DISCONNECTED AT THE
	SAME TIME 210.4(B).

	13) OCCUPIABLE BALCONIES AND PORCHES OVER 20 SQ FT MUST
	NOW HAVE A RECEPTACLE OUTLET (GFCI PROTECTED)
	(210.52(E)(3).

	14) RECEPTACLES SHALL BE INSTALLED SUCH THAT NO POINT
	MEASURED HORIZONTALLY ALONG THE FLOOR LINE IN ANY WALL
	SPACE IS MORE THAN 6 FEET FROM A RECEPTACLE OUTLET. NEC
	210.52(A)(1)

	15) ANY SPACE 2 FEET OR MORE IN WIDTH (INCLUDING SPACE
	MEASURED AROUND CORNERS) AND UNBROKEN ALONG THE FLOOR
	LINE BY DOORS, FIREPLACES, AND SIMILAR OPENINGS. NEC
	210.52(A)(2)(1)

	16) SMALL-APPLIANCE BRANCH CIRCUITS IN ADDITION TO THE
	NUMBER OF BRANCH CIRCUITS REQUIRED BY OTHER PARTS OF
	THIS SECTION, TWO OR MORE 20-AMPERE SMALL-APPLIANCE
	BRANCH CIRCUITS SHALL BE PROVIDED FOR ALL RECEPTACLE
	OUTLETS SPECIFIED BY NEC 210.52(B).

	17) THE VALUE OF THE PROJECT ISNT REALISTIC AND WILL BE
	REVISED TO INCLUDE THE OVERALL SCOPE OF WORK. FBC WPB
	AMENDMENTS. SECTION 109.3

	18) FOR A ONE FAMILY DWELLING AND EACH UNIT OF A
	TWO-FAMILY DWELLING THAT IS AT GRADE LEVEL, AT LEAST
	ONE RECEPTACLE OUTLET ACCESSIBLE WHILE STANDING AT
	GRADE LEVEL AND LOCATED NOT MORE THAN 2.0 M (61.2 FT)
	ABOVE GRADE SHALL BE INSTALLED AT THE FRONT AND BACK OF
	THE DWELLING. NEC 210.52(E)(3)

	19) PROVIDE MANUFACTURER PRODUCT ELECTRICAL
	SPECIFICATIONS FOR THE WALL MOUNTED A/C UNIT. INDICATE
	A COMPATABLE ELECTRICAL RECEPTACLE OUTLET FOR SAME.

	20) ALL INFORMATION, DRAWINGS, SPECIFICATIONS AND
	ACCOMPANYING DATA SHALL BEAR THE NAME AND SIGNATURE OF
	THE PERSON RESPONSIBLE FOR THE DESIGN. WPB AMENDMENTS
	TO FBC 107.2.1

	WHEN RESUBMITTING, IT IS HELPFUL TO PROVIDE A RESPONSE
	LETTER ADDRESSING EACH ITEM ALONG WITH THE CITY
	RE-SUBMITTAL FORM. SEE LINK:
	HTTP://WPB.ORG/DEVELOPMENT/WP-CONTENT/UPLOADS/SITES/33/
	2013/09/APPLICATION_RESUBMITTAL_FORM_04132010.PDF

	ADDITIONALLY, PLEASE INSERT CORRECTED PAGES INTO
	SUBMITTAL PACKAGE AND LEAVE THE PREVIOUSLY REVIEWED
	SHEETS FOR COMPARATIVE REVIEW.

	DAVID HAYES, ELECTRICAL PLANS EXAMINER, PX3421,
	561-805-6717 OR [email protected]

Review Stop	G			GAS REVIEW
Rev No	4	Status	P	Date	2015-03-21			Cont ID
Sent By	rmcdouga			Date	2015-03-21	Time	08:18	Rev Time	0.00
Received By	tklarge			Date	2015-03-21	Time	07:32	Sent To	B

Notes

***NONE***

Review Stop	G			GAS REVIEW
Rev No	3	Status	F	Date	2015-02-15			Cont ID
Sent By	tklarge			Date	2015-02-15	Time	06:14	Rev Time	0.00
Received By	tklarge			Date	2015-02-15	Time	05:45	Sent To

Notes

2015-02-15 05:58:37	1) SUBMIT COPIES OF THE APPLICABLE GAS SIZING TABLE
	FROM THE 2010 FBCR SEC. G2413.3 OR REFERENCE THE
	SPECIFIC SIZING TABLES ON THE PLANS FOR EACH TYPE OF
	PIPE MATERIAL USED FOR THE GAS SYSTEM. 3RD REQUEST.
	2) SUBMIT MANUFACTURER SPECIFICATION SHEETS FOR THE GAS
	REGULATORS. REGULATORS SHALL COMPLY W/ 2010 FBCR
	SEC.G2421.3. 3RD REQUEST.
	3) SPECS FOR A GAS RANGE HAVE BEEN SUBMITTED AND A GAS
	RANGE IS SHOWN ON THE GAS RISER.THE ZONING CODE DOES
	NOT ALLOW A KITCHEN IN THIS STRUCTURE AS IT CAN ONLY BE
	USED AS AN ACCESSORY STRUCTURE TO THE MAIN HOUSE.
	REMOVE THE THE GAS RANGE PIPNG FROM THE GAS RISER
	DIAGRAM COMPLETELY. DO NOT SHOW A CAPPED LINE.
	4) SUBMIT 2 COPIES OF A FULL SET OF MANUFACTURER'S
	SPECIFICATIONS FOR THE PORTABLE GENERATOR AND THE GAS
	BBQ GRILL. THE INFORMATION THAT WAS SUBMITTED IS
	INADEQUATE AND INCOMPLETE. WPB AMEND. TO 2010 FBC SEC.
	107.2.1.3RD REQUEST.


	PLUMBING PLAN REVIEW
	TIM LARGE
	CHIEF PLUMBING INSPECTOR
	561-805-6692
	[email protected]

Review Stop	G			GAS REVIEW
Rev No	2	Status	F	Date	2014-12-22			Cont ID
Sent By	tklarge			Date	2014-12-22	Time	15:11	Rev Time	0.00
Received By	tklarge			Date	2014-12-22	Time	15:11	Sent To

Notes

2014-12-22 14:40:38	1) SUBMIT THE MANUFACTURER'S SPECIFICATIONS FOR THE
	GENERATOR & BBQ GRILL. FBCR SEC.G2404.3. 2ND REQUEST
	2) SUBMIT CALCULATIONS FOR COMBUSTION AIR FOR THE
	TANKLESS WATER HEATER PER SEC.304 OF THE 2010 FBCR
	SEC.G2407
	3) SUBMIT COPIES OF THE APPLICABLE GAS SIZING TABLE
	FROM THE 2010 FBCR SEC. G2413.3.
	4) SHOW THE TOTAL DISTANCE FROM THE GAS POINT OF
	DELIVERY TO THE MOST REMOTE OUTLET. FBCR SEC. G2413.3.
	5) SHOW THE PIPE SIZES FOR ALL SECTIONS OF THE PIPING
	SYSTEM.WPB AMEND. TO 2010 FBC SEC.107.2.1.
	6) THE VENT SHALL TERMINATE A MINIMUM OF 2 FT. ABOVE
	THE WALL/ROOF PER 2010 FBCR SEC.G2427.6.3 OR MANUF.
	INSTALLATION INSTRUCTIONS. SHOW THIS ON THE PLAN. 2ND
	REQUEST.
	7) GALVANIZED PIPING IS NOT APPROVED FOR USE
	UNDERGROUND PER THE 2010 FBCR SEC.G2414.8, G2415.9.
	8) THE PRESSURE REGULATOR FOR THE TANKLESS WATER HEATER
	SHALL BE VENTED TO THE EXTERIOR PER THE 2010 FBCR
	SEC.2421.3.
	9) SUBMIT MANUF. SPEC. SHEETS FOR THE
	REGULATORS.REGULATORS SHALLL COMPLY WITH 2010 FBCR
	SEC.G2421.1.
	10) A LISTED SHUTOFF VALVE SHALL BE LOCATED IMMEDIATELY
	AHEAD OF EACH MP (MEDIUM PRESSURE) REGULATOR.FBCR
	SEC.G2420.4.
	SEARCH OF CITY RECORDS SHOWS A PERMIT WAS ONLY ISSUED
	FOR THE RANGE. ANY OTHER GAS WORK THAT HAS BEEN
	INSTALLED HAS BEEN DONE WITHOUT THE PROPER PERMITS OR
	INSPECTIONS AND SHALL BE EXPOSED FOR INSPECTION.


	PLUMBING PLAN REVIEW
	TIM LARGE
	CHIEF PLUMBING INSPECTOR
	561-805-6692
	[email protected]

Review Stop	G			GAS REVIEW
Rev No	1	Status	F	Date	2014-09-16			Cont ID
Sent By	tklarge			Date	2014-09-16	Time	06:39	Rev Time	0.00
Received By	tklarge			Date	2014-09-15	Time	13:54	Sent To

Notes

2014-09-15 14:19:58	1) SUBMIT THE MANUFACTURER'S SPECIFICATIONS FOR THE
	TANKLESS WATER HEATER, GENERATOR,& BBQ GRIL. FBCR
	SEC.G2404.3.
	2) SUBMIT A LEGIBLE GAS DRAWING. THE SUBMITTED DRAWING
	IS TOO DIFFICULT TO READ DUE TO THE SMALL PRINTING.
	PLANS SHALL BE DRAWN TO A MIN. 1/8 " SCALE. WPB ADMIN.
	AMEND. TO 2010 FBC SEC.107.2.1.4.
	3) THE GAS RISER SHALL SHOW THE BTU LOAD FOR EACH
	APPLIANCE. THE BTU LOAD FOR THE TANKLESS WATER HEATER
	SHALL BE SPECIFIC ( THE PLAN SHOWS A RANGE OF
	10,300-180,000 BTU'S.
	4) SUBMIT COPIES OF THE APPLICABLE GAS SIZING TABLE FOR
	THIS INSTALLATION.
	5) SHOW THE DIMENSION OF EACH SECTION OF PIPE AND THE
	TOATAL DISTANCE FROM THE GAS POINT OF DELIVERY TO THE
	MOST REMOTE OUTLET.
	6) SHOW THE PIPE SIZES FOR ALL SECTIONS OF THE PIPING
	SYSTEM.
	7) SHOW THE TYPE OF VENT FOR THE TANKLESS WATER HEATER.
	THE VENT SHALL TERMINATE A MINIMUM OF 2 FT. ABOVE THE
	WALL/ROOF PER 2010 FBCR SEC.G2427.5.3.
	8) SEARCH OF CITY RECORDS SHOWS A PERMIT WAS ONLY
	ISSUED FOR THE RANGE. ANY OTHER GAS WORK THAT HAS BEEN
	INSTALLED HAS BEEN DONE WITHOUT THE PROPER PERMITS OR
	INSPECTIONS.

	PLUMBING PLAN REVIEW
	TIM LARGE
	CHIEF PLUMBING INSPECTOR
	561-805-6692
	[email protected]

Review Stop	I		INCOMING/PROCESSING
Rev No	4	Status	Date				Cont ID
Sent By	tlarge		Date		Time		Rev Time	0.00
Received By	dhayes		Date	2015-03-18	Time	16:23	Sent To	G

Notes

***NONE***

Review Stop	I			INCOMING/PROCESSING
Rev No	3	Status	N	Date	2015-03-12			Cont ID
Sent By	dhayes			Date	2015-03-12	Time	09:46	Rev Time	0.00
Received By	dhayes			Date	2015-02-10	Time	08:56	Sent To

Notes

***NONE***

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2015-01-08			Cont ID
Sent By	dhayes			Date	2015-01-08	Time	11:19	Rev Time	0.00
Received By	dhayes			Date	2014-12-19	Time	17:15	Sent To

Notes

2014-12-19 17:15:11	R06

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2014-09-17			Cont ID
Sent By	dhayes			Date	2014-09-17	Time	08:16	Rev Time	0.00
Received By	dhayes			Date	2014-08-21	Time	07:31	Sent To

Notes

2014-08-22 07:31:38

R-17

Review Stop	P			PLUMBING
Rev No	3	Status	P	Date	2015-02-15			Cont ID
Sent By	tklarge			Date	2015-02-15	Time	05:45	Rev Time	0.00
Received By	tklarge			Date	2015-02-15	Time	05:12	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	2	Status	P	Date	2014-12-22			Cont ID
Sent By	tklarge			Date	2014-12-22	Time	14:18	Rev Time	0.00
Received By	tklarge			Date	2014-12-22	Time	11:28	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2014-09-16			Cont ID
Sent By	tklarge			Date	2014-09-16	Time	06:30	Rev Time	0.00
Received By	tklarge			Date	2014-09-16	Time	06:30	Sent To

Notes

2014-09-16 06:37:13	1) CITY RECORDS DO NOT SHOW ANY PERMITS THAT WERE
	ISSUED FOR THE INSTALLATION OF THE PLUMBING WORK THAT
	IS PRESENT. THIS WORK SHALL BE LEGALLY PERMITTTED AND
	INSPECTED OR IT SHALL BE REMOVED IF NOT PERMITTED BY
	THE ZONING DEPT. SEE ZONING COMMENTS.WPB ADMIN. AMEND.
	TO 2010 FBC SEC.105.1.
	2) SHOW THE SHOWER DIMENSIONS ( LXW) ON THE PLANS. THE
	SHOWER SHALL BE A MIN. OF 30" IN WIDTH AND A MIN. OF
	900 SQ. INCHES. 2010 FBCR SEC.P2708.

	PLUMBING PLAN REVIEW
	TIM LARGE
	CHIEF PLUMBING INSPECTOR
	561-805-6692
	[email protected]

Review Stop	Z			ZONING
Rev No	3	Status	P	Date	2015-02-11			Cont ID
Sent By	dkittred			Date	2015-02-11	Time	15:10	Rev Time	0.00
Received By	dkittred			Date	2015-02-11	Time	09:52	Sent To

Notes

***NONE***

Review Stop	Z			ZONING
Rev No	2	Status	P	Date	2014-12-23			Cont ID
Sent By	dkittred			Date	2014-12-23	Time	13:32	Rev Time	0.00
Received By	dkittred			Date	2014-12-23	Time	13:16	Sent To

Notes

2014-12-23 13:32:51	PLANNING AND ZONING COMMENTS:

	12/23/14

	IMPROVEMENTS TO ACCESSORY STRUCTURE FOR USE WITH MAIN
	HOUSE ONLY. CURRENT AND/OR FUTURE USE OF THE ACCESSORY
	STRUCTURE AS AN ACCESSORY APARTMENT IS NOT PERMITTED.

	IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT:

	DANIELLE J. KITTREDGE, AICP
	SENIOR PLANNER
	PLANNING & ZONING DIVISION
	PHONE: (561)-822-1443
	EMAIL: [email protected]

Review Stop	Z			ZONING
Rev No	1	Status	F	Date	2014-08-27			Cont ID
Sent By	llouie			Date	2014-08-27	Time	10:18	Rev Time	0.00
Received By	dkittred			Date	2014-08-27	Time	09:06	Sent To

Notes

2014-08-27 10:18:47	PLANNING AND ZONING COMMENTS: *FAILED*

	8/26/14

	1. IT IS UNCLEAR FROM THE PLANS WHAT IS NEW AND WHAT IS
	EXISTING. PERMIT APPLICATION INDICATES 'REPAIRS',
	HOWEVER, IT APPEARS A COMPLETE REMODEL OF THE ACCESSORY
	STRUCTURE IS PROPOSED. PLEASE CLARIFY ON THE PLANS.
	(FOR EXAMPLE, ARE THE BATHROOM AND STORAGE ROOM
	CURRENTLY EXISTING AND REPAIRS ARE PROPOSED OR ARE
	THESE COMPLETELY NEW INTERIOR SPACES BEING PROPOSED?)

	2. PLEASE NOTE THAT USE OF THE RENOVATED ACCESSORY
	STRUCTURE FOR AN ACCESSORY APARTMENT IS NOT PERMITTED
	AT THIS LOCATION. THE PLANS DO NOT INDICATE AN
	ACCESSORY APARTMENT AS THE INTENDED USE, HOWEVER,
	IMPROVEMENTS PROPOSED ARE MORE CONSISTENT WITH AN
	ACCESSORY APARTMENT THAN A HOME OFFICE. KITCHEN/COOKING
	FACILITIES ARE NOT PERMITTED IN THE ACCESSORY
	STRUCTURE. PROPOSED REFRIGERATOR SHALL BE 'UNDER
	COUNTER' STYLE ONLY TO MEET THIS INTENT.

	IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT:

	DANIELLE J. KITTREDGE, AICP
	SENIOR PLANNER
	PLANNING & ZONING DIVISION
	PHONE: (561)-822-1443
	EMAIL: [email protected]

2014-08-26 13:50:41	8/26/14