Plan Review Details - Permit 13051103
Plan Review Stops For Permit 13051103
Review Stop B BUILDING (STRUCTURAL)
Rev No 3 Status P Date 2013-08-29 Cont ID  
Sent By jwitmer Date 2013-08-29 Time 15:28 Rev Time 0.00
Received By jwitmer Date 2013-08-29 Time 15:28 Sent To  
Notes
***NONE***
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status F Date 2013-07-26 Cont ID  
Sent By J WITMER Date 2013-07-26 Time 14:48 Rev Time 0.00
Received By jwitmer Date 2013-07-26 Time 13:46 Sent To  
Notes
2013-07-26 13:59:26BUILDING PLAN REVIEW
 PERMIT: 13051103
 ADD: 911 VILLAGE BLVD
 CONT: KARNS & BALDWIN INNOVATIVE BUILDERS
 TEL: (561)805-7528
  
 2010 FLORIDA BUILDING CODE W
 * WEST PALM BEACH ADMINISTRATIVE AMENDMENTS
  
 2010 EXISTING BUILDING CODE LEVEL II 701.3
 COMPLIANCE. ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS,
 SYSTEMS, AND SPACES SHALL COMPLY WITH THE REQUIREMENTS
 OF THE FLORIDA BUILDING CODE, BUILDING.
  
 2ND REVIEW
 DATE: JULY 26/2013
 ACTION: DENIED
  
 1) COMPLIED.
  
 2) SHEET 2 INDICATES THE USE OF CLOSED CELL ICYENE R-8
 INSULATION APPLIED TO THE BOTTOM OF THE BAR JOIST.
 PLEASE PROVIDE THE MANUFACTURERS SPECIFICATION FOR
 ICYENE PROVIDING HOW THICK THE INSULATION WILL NEED TO
 BE APPLIED TO ACHIEVE A R-8 VALUE. DISCREPANCY IN
 SUBMITTED PAPERWORK, PRODUCT INFORMATION FOR
 CERTAINTEED CERTA SPRAY CLOSED CELL FOAM WAS SUBMITTED,
 NOT A TESTING REPORT, THE DESIGNER OF RECORD SPECIFIES
 THE BRAND NAME ICYENE. THE PRODUCT INFORMATION FOR DC
 315 FIRE PROOF PAINT DOES NOT PROVIDE THE ACTUAL
 TESTING REPORT BY A RECONIGNED NATIONAL TESTING AGENCY,
 THE THIRD SUBMITTAL IS A MIAMI-DADE NOA 130306.07
 CERTAIN TEED ROOF INSULATION AND SHEATING, SHEET 3 OF 4
 INDICATES 3 TYPES OF SUB-SYSTEMS THAT ARE TO BE
 INSTALLED ON TOP OF A METAL ROOF, IF THIS SYSTEM IS TO
 BE PINNED FROM BENEATH THE ROOF THERE IS NO LITERATURE
 FOR PINNING, AGAIN THIS SYSTEM IF USED UNDER THE ROOF
 DECK WILL NEED TO COMPLY WITH 2010 FBC-B 2603.4AND OR
 2603.4.1.6.
  
 2010 CHAPTER 1 WEST PALM BEACH ADMINISTRATIVE CODE,
 107.2.1 INFORMATION ON CONSTRUCTION DOCUMENTS.
 CONSTRUCTION DOCUMENTS SHALL BE
 DIMENSIONED AND DRAWN UPON SUITABLE MATERIAL. SUCH
 INFORMATION SHALL BE SPECIFIC, AND THE TECHNICAL CODES
 SHALL NOT BE CITED AS A WHOLE OR IN PART, NOR SHALL THE
 TERM "LEGAL" OR ITS EQUIVALENT BE USED AS A SUBSTITUTE
 FOR SPECIFIC INFORMATION.
  
 2A) PROVIDE PRODUCT COMPLIANCE FOR:
 FBC-B 2603.5.2 THERMAL BARRIER. ANY FOAM PLASTIC
 INSULATION SHALL BE SEPARATED FROM THE BUILDING
 INTERIOR BY A THERMAL BARRIER MEETING THE PROVISIONS OF
 SECTION 2603.4, UNLESS SPECIAL APPROVAL IS OBTAINED ON
 THE BASIS OF SECTION 2603.9.
  
 FBC-B 2603.9 SPECIAL APPROVAL.
 FOAM PLASTIC SHALL NOT BE REQUIRED TO COMPLY WITH THE
 REQUIREMENTS OF SECTIONS 2603.4 THROUGH 2603.7 WHERE
 SPECIFICALLY APPROVED BASED ON LARGE-SCALE TESTS SUCH
 AS, BUT NOT LIMITED TO, NFPA 286 (WITH THE
 ACCEPTANCE CRITERIA OF SECTION 803.2), FM 4880, UL 1040
 OR UL 1715. SUCH TESTING SHALL BE RELATED TO THE ACTUAL
 END-USE CONFIGURATION AND BE PERFORMED ON THE FINISHED
 MANUFACTURED FOAM PLASTIC
 ASSEMBLY IN THE MAXIMUM THICKNESS INTENDED FOR USE.
 FOAM PLASTICS THAT ARE USED AS INTERIOR FINISH ON THE
 BASIS OF SPECIAL TESTS SHALL ALSO CONFORM TO THE FLAME
 SPREAD REQUIREMENTS OF CHAPTER 8. ASSEMBLIES
 TESTED SHALL INCLUDE SEAMS, JOINTS AND OTHER TYPICAL
 DETAILS USED IN THE INSTALLATION OF THE ASSEMBLY AND
 SHALL BE TESTED IN THE MANNER INTENDED FOR USE.
  
 2B) 2603.7 PLENUMS. FOAM PLASTIC INSULATION SHALL NOT
 BE USED AS INTERIOR WALL OR CEILING FINISH IN PLENUMS
 EXCEPT AS PERMITTED IN SECTION 2604 OR WHEN PROTECTED
 BY A THERMAL BARRIER IN ACCORDANCE WITH SECTION 2603.4.
  
 2C) DEPENDING ON THE METHOD OF APPLICATION THIS CODE
 SECTION MAY ALSO HAVE SOME REVEVANCE, ONCE THE
 MANUFACTURERS SPECS AND TYPE OF APPLICATION IS KNOWN.
 2603.4.1.6 ATTICS AND CRAWL SPACES.
 WITHIN AN ATTIC OR CRAWL SPACE WHERE ENTRY IS MADE ONLY
 FOR SERVICE OF UTILITIES, FOAM PLASTIC INSULATION SHALL
 BE PROTECTED AGAINST IGNITION BY 11/2-INCH-THICK (38
 MM) MINERAL FIBER INSULATION; 1/4-INCH-THICK (6.4 MM)
 WOOD STRUCTURAL PANEL, PARTICLEBOARD OR HARDBOARD;
 3/8-INCH (9.5 MM) GYPSUM WALLBOARD, CORROSION-RESISTANT
 STEEL HAVING A BASE METAL THICKNESS OF 0.016 INCH (0.4
 MM) OR OTHER APPROVED MATERIAL INSTALLED IN SUCH A
 MANNER THAT THE FOAM PLASTIC INSULATION IS NOT EXPOSED.
 THE PROTECTIVE COVERING SHALL BE CONSISTENT WITH THE
 REQUIREMENTS FOR THE TYPE OF CONSTRUCTION.
  
 3) COMPLIED.
  
 4) BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
 FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
 PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
 A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
 APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
  
 JAMES A. WITMER CBO
 SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
 TEL: 561-805-6715
 FAX: 561-805-6676
 E-MAIL: [email protected]
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2013-07-03 Cont ID  
Sent By jwitmer Date 2013-07-03 Time 17:59 Rev Time 0.00
Received By jwitmer Date 2013-07-03 Time 17:00 Sent To  
Notes
2013-07-03 17:51:15BUILDING PLAN REVIEW
 PERMIT: 13051103
 ADD: 911 VILLAGE BLVD
 CONT: KARNS & BALDWIN INNOVATIVE BUILDERS
 TEL: (561)805-7528
  
 2010 FLORIDA BUILDING CODE W
 * WEST PALM BEACH ADMINISTRATIVE AMENDMENTS
  
 2010 EXISTING BUILDING CODE LEVEL II 701.3
 COMPLIANCE. ALL NEW CONSTRUCTION ELEMENTS, COMPONENTS,
 SYSTEMS, AND SPACES SHALL COMPLY WITH THE REQUIREMENTS
 OF THE FLORIDA BUILDING CODE, BUILDING.
  
 1ST REVIEW
 DATE: JULY 03/2013
 ACTION: DENIED
  
 1) SHEET 1 PLEASE CORRECT OCCUPANCY TYPE TO A-3, 2010
 FBC-B SECTION 303.1.
  
 2) SHEET 2 INDICATES THE USE OF CLOSED CELL ICYENE R-8
 INSULATION APPLIED TO THE BOTTOM OF THE BAR JOIST.
 PLEASE PROVIDE THE MANUFACTURERS SPECIFICATION FOR
 ICYENE PROVIDING HOW THICK THE INSULATION WILL NEED TO
 BE APPLIED TO ACHIEVE A R-8 VALUE.
 2A) PROVIDE PRODUCT COMPLIANCE FOR:
 FBC-B 2603.5.2 THERMAL BARRIER. ANY FOAM PLASTIC
 INSULATION SHALL BE SEPARATED FROM THE BUILDING
 INTERIOR BY A THERMAL BARRIER MEETING THE PROVISIONS OF
 SECTION 2603.4, UNLESS SPECIAL APPROVAL IS OBTAINED ON
 THE BASIS OF SECTION 2603.9.
  
 FBC-B 2603.9 SPECIAL APPROVAL.
 FOAM PLASTIC SHALL NOT BE REQUIRED TO COMPLY WITH THE
 REQUIREMENTS OF SECTIONS 2603.4 THROUGH 2603.7 WHERE
 SPECIFICALLY APPROVED BASED ON LARGE-SCALE TESTS SUCH
 AS, BUT NOT LIMITED TO, NFPA 286 (WITH THE
 ACCEPTANCE CRITERIA OF SECTION 803.2), FM 4880, UL 1040
 OR UL 1715. SUCH TESTING SHALL BE RELATED TO THE ACTUAL
 END-USE CONFIGURATION AND BE PERFORMED ON THE FINISHED
 MANUFACTURED FOAM PLASTIC
 ASSEMBLY IN THE MAXIMUM THICKNESS INTENDED FOR USE.
 FOAM PLASTICS THAT ARE USED AS INTERIOR FINISH ON THE
 BASIS OF SPECIAL TESTS SHALL ALSO CONFORM TO THE FLAME
 SPREAD REQUIREMENTS OF CHAPTER 8. ASSEMBLIES
 TESTED SHALL INCLUDE SEAMS, JOINTS AND OTHER TYPICAL
 DETAILS USED IN THE INSTALLATION OF THE ASSEMBLY AND
 SHALL BE TESTED IN THE MANNER INTENDED FOR USE.
  
 2B) 2603.7 PLENUMS. FOAM PLASTIC INSULATION SHALL NOT
 BE USED AS INTERIOR WALL OR CEILING FINISH IN PLENUMS
 EXCEPT AS PERMITTED IN SECTION 2604 OR WHEN PROTECTED
 BY A THERMAL BARRIER IN ACCORDANCE WITH SECTION 2603.4.
  
 2C) DEPENDING ON THE METHOD OF APPLICATION THIS CODE
 SECTION MAY ALSO HAVE SOME REVEVANCE, ONCE THE
 MANUFACTURERS SPECS AND TYPE OF APPLICATION IS KNOWN.
 2603.4.1.6 ATTICS AND CRAWL SPACES.
 WITHIN AN ATTIC OR CRAWL SPACE WHERE ENTRY IS MADE ONLY
 FOR SERVICE OF UTILITIES, FOAM PLASTIC INSULATION SHALL
 BE PROTECTED AGAINST IGNITION BY 11/2-INCH-THICK (38
 MM) MINERAL FIBER INSULATION; 1/4-INCH-THICK (6.4 MM)
 WOOD STRUCTURAL PANEL, PARTICLEBOARD OR HARDBOARD;
 3/8-INCH (9.5 MM) GYPSUM WALLBOARD, CORROSION-RESISTANT
 STEEL HAVING A BASE METAL THICKNESS OF 0.016 INCH (0.4
 MM) OR OTHER APPROVED MATERIAL INSTALLED IN SUCH A
 MANNER THAT THE FOAM PLASTIC INSULATION IS NOT EXPOSED.
 THE PROTECTIVE COVERING SHALL BE CONSISTENT WITH THE
 REQUIREMENTS FOR THE TYPE OF CONSTRUCTION.
  
 3) SHEET 2 SHOWS A 42 INCH HIGH JUICE BAR, PLEASE
 PROVIDE HOW COMPLIANCE WITH SECTION 2010 FBC-B 902.3
 HEIGHT. THE TOPS OF DINING SURFACES AND WORK SURFACES
 SHALL BE 28 INCHES (710 MM) MINIMUM AND 34 INCHES (865
 MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.
  
 BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
 FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
 PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
 A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
 APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
  
 JAMES A. WITMER CBO
 SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
 TEL: 561-805-6715
 FAX: 561-805-6676
 E-MAIL: [email protected]
Review Stop E ELECTRICAL
Rev No 3 Status P Date 2013-09-03 Cont ID  
Sent By dharvey Date 2013-09-03 Time 17:13 Rev Time 0.00
Received By dharvey Date 2013-09-03 Time 17:13 Sent To  
Notes
2013-09-03 17:15:139-3-13
 NO CHANGES ON DRAWINGS INSERTED IN PLAN SET. SAME DATE
 AS PREVIOUSLY REVIEWED.
 E2.1 AND E3.1......
 VB
  
Review Stop E ELECTRICAL
Rev No 2 Status P Date 2013-08-26 Cont ID  
Sent By dharvey Date 2013-08-26 Time 08:13 Rev Time 0.00
Received By dharvey Date 2013-08-26 Time 07:20 Sent To  
Notes
***NONE***
Review Stop E ELECTRICAL
Rev No 1 Status P Date 2013-06-18 Cont ID  
Sent By dharvey Date 2013-06-18 Time 11:53 Rev Time 0.00
Received By dharvey Date 2013-06-18 Time 11:45 Sent To  
Notes
2013-06-18 11:53:15REVIEWED BY RL
Review Stop FIRE FIRE DEPARTMENT
Rev No 3 Status P Date 2013-09-03 Cont ID  
Sent By wjolin Date 2013-09-03 Time 13:54 Rev Time 0.00
Received By wjolin Date 2013-09-03 Time 13:48 Sent To  
Notes
***NONE***
Review Stop FIRE FIRE DEPARTMENT
Rev No 2 Status F Date 2013-07-17 Cont ID  
Sent By W JOLIN Date 2013-07-17 Time 16:54 Rev Time 0.00
Received By wjolin Date 2013-07-17 Time 16:46 Sent To  
Notes
2013-07-17 16:54:27911 VILLAGE BOULEVARD - SUITE #803
 PERMIT #13051103
 REVIEW #2 COMMENTS - FIRE DEPARTMENT
  
 THE FOLLOWING MEP SHEETS WERE NOT RESUBMITTED FOR
 REVIEW TO ADDRESS THE ORIGINAL PLAN REVIEW COMMENTS:
  
 SHEET 2 AND SHEET E2.1: SHEET 2 INDICATES AN EXTERIOR
 STOREFRONT DOOR TO BE PERMANENTLY SECURED; HOWEVER,
 SHEET E2.1 INDICATES AN EXIT SIGN AT THIS DOOR.
 COORDINATE. IF THIS DOOR IS NOT AN EXIT DOOR, PROVIDE
 PERMANENT OBVIOUS SIGNAGE ON DOOR INDICATING "NOT AN
 EXIT."
  
 SHEET E2.1: NO EXIT SIGN PROVIDED FOR REAR EXIT DOOR.
  
 SHEET M2.1 - DUCT-SOX: THE FLAME SPREAD AND SMOKE
 DEVELOPMENT OF FLEXIBLE AIR DUCTS NEED TO BE LISTED AND
 LABELED AS CLASS 0 OR CLASS 1 PER UL 181. CLASS 0 - AIR
 DUCTS AND AIR CONNECTORS HAVING SURFACE BURNING
 CHARACTERISTICS OF ZERO. CLASS 1 - AIR DUCTS AND AIR
 CONNECTORS HAVING A FLAME-SPREAD INDEX OF NOT OVER 25
 WITHOUT EVIDENCE OF CONTINUED PROGRESSIVE COMBUSTION
 AND A SMOKE-DEVELOPED INDEX OF NOT OVER 50.
  
 SHEET M2.1: VERIFY EXISTING 10 TON AND 7.5 TON UNITS
 ARE EQUIPPED WITH DUCT SMOKE DETECTORS.
  
 WESLEY JOLIN
 FIRE INVESTIGATOR & INSPECTOR
 OFFICE OF THE FIRE MARSHAL
 WEST PALM BEACH FIRE RESCUE
 [email protected]
 (561) 805-6730
Review Stop FIRE FIRE DEPARTMENT
Rev No 1 Status F Date 2013-06-14 Cont ID  
Sent By wjolin Date 2013-06-14 Time 15:01 Rev Time 0.00
Received By wjolin Date 2013-06-14 Time 14:32 Sent To  
Notes
2013-06-14 15:01:01911 VILLAGE BOULEVARD - SUITE #803
 PERMIT #13051103
 REVIEW COMMENTS - FIRE DEPARTMENT
  
 GENERAL: PROVIDE DRAWING NOTE INDICATING, "FIRE
 PROTECTION SYSTEMS SHALL REMAIN ACTIVE DURING
 DEMOLITION AND RENOVATION ACTIVITIES. IN THE EVENT A
 FIRE PROTECTION SYSTEM IS OUT OF SERVICE FOR MORE THAN
 4-HOURS IN A 24-HOUR PERIOD, THE BUILDING SHALL BE
 PLACED UNDER A FIRE WATCH. ALL FIRE WATCH REQUESTS MUST
 BE SUBMITTED BY EMAIL ([email protected]) OR IN WRITING
 (FAX: 561-804-4774) AND APPROVED BY THE OFFICE OF THE
 FIRE MARSHAL LOCATED AT 500 NORTH DIXIE HIGHWAY."
  
 GENERAL: PROVIDE AN EXTERIOR KEY SAFE TO ALLOW
 EMERGENCY RESPONDERS NON-FORCIBLE ENTRY INTO THE
 BUILDING DURING NON-BUSINESS HOURS. A KEY SAFE CAN BE
 ORDERED FROM WWW.KNOXBOX.COM.
  
 SHEET 1: PLAN INDICATES THIS TO BE A BUSINESS
 OCCUPANCY; HOWEVER, THIS IS AN ASSEMBLY OCCUPANCY. PER
 THE LIFE SAFETY CODE, "ASSEMBLY OCCUPANCY IS DEFINED AS
 AN OCCUPANCY USED FOR A GATHERING OF 50 OR MORE PERSONS
 FOR DELIBERATION, WORSHIP, ENTERTAINMENT, EATING,
 DRINKING, AMUSEMENT, AWAITING TRANSPORTATION, OR
 SIMILAR USES. BUSINESS OCCUPANCY IS DEFINED AS AN
 OCCUPANCY USED FOR THE TRANSACTION OF BUSINESS OTHER
 THAN MERCANTILE."
  
 SHEET 1: INDICATE THE DOOR HARDWARE ON THE MAIN
 ENTRANCE/EXIT DOORS. FOR ASSEMBLY OCCUPANCIES WITH AN
 OCCUPANT LOAD OF 100 OR MORE PERSONS, PANIC HARDWARE
 SHALL BE PROVIDED ON DOORS TO RELEASE THE LOCK/LATCH.
 NO OTHER LOCKS OR LATCHES ARE PERMITTED THAT WOULD NOT
 BE RELEASED BY THE PANIC HARDWARE. AS A SUBSTITUTE FOR
 PANIC HARDWARE, THE MAIN ENTRANCE (ONLY) IS PERMITTED
 TO HAVE AN INTERIOR KEYED DOOR LOCK (AND NO LATCH) WITH
 A READILY VISIBLE SIGN STATING THIS DOOR TO REMAIN
 UNLOCKED WHEN THE BUILDING IS OCCUPIED. SIGN LETTERS
 SHALL BE AT LEAST 1 INCH IN HEIGHT. A THUMB TURN STYLE
 LOCK IS NOT PERMITTED TO BE SUBSTITUTED FOR A KEYED
 LOCK.
  
 SHEET 2 AND SHEET E2.1: SHEET 2 INDICATES AN EXTERIOR
 STOREFRONT DOOR TO BE PERMANENTLY SECURED; HOWEVER,
 SHEET E2.1 INDICATES AN EXIT SIGN AT THIS DOOR.
 COORDINATE. IF THIS DOOR IS NOT AN EXIT DOOR, PROVIDE
 PERMANENT OBVIOUS SIGNAGE ON DOOR INDICATING "NOT AN
 EXIT."
  
 GENERAL: PROVIDE TACTILE SIGNAGE AT ALL REQUIRED EXIT
 DOORS WITH EXIT SIGNS.
  
 GENERAL: EVERY ASSEMBLY OCCUPANCY ROOM NOT HAVING FIXED
 SEATS SHALL HAVE THE OCCUPANT LOAD OF THE ROOM POSTED
 IN A CONSPICUOUS PLACE NEAR THE MAIN EXIT FROM THE
 ROOM. SIGNS SHALL BE DURABLE AND INDICATE THE NUMBER OF
 OCCUPANTS PERMITTED FOR EACH ROOM.
  
 SHEET E2.1: NO EXIT SIGN PROVIDED FOR REAR EXIT DOOR.
  
 SHEET M2.1 - DUCT-SOX: THE FLAME SPREAD AND SMOKE
 DEVELOPMENT OF FLEXIBLE AIR DUCTS NEED TO BE LISTED AND
 LABELED AS CLASS 0 OR CLASS 1 PER UL 181. CLASS 0 - AIR
 DUCTS AND AIR CONNECTORS HAVING SURFACE BURNING
 CHARACTERISTICS OF ZERO. CLASS 1 - AIR DUCTS AND AIR
 CONNECTORS HAVING A FLAME-SPREAD INDEX OF NOT OVER 25
 WITHOUT EVIDENCE OF CONTINUED PROGRESSIVE COMBUSTION
 AND A SMOKE-DEVELOPED INDEX OF NOT OVER 50.
  
 SHEET M2.1: VERIFY EXISTING 10 TON AND 7.5 TON UNITS
 ARE EQUIPPED WITH DUCT SMOKE DETECTORS.
  
 NOTE: SEPARATE PLANS AND PERMITS ARE REQUIRED FOR THE
 MODIFICATION OF THE FIRE SPRINKLER SYSTEM.
  
 WESLEY JOLIN
 FIRE INVESTIGATOR & INSPECTOR
 OFFICE OF THE FIRE MARSHAL
 WEST PALM BEACH FIRE RESCUE
 [email protected]
 (561) 805-6730
  
Review Stop G GAS REVIEW
Rev No 1 Status P Date 2013-07-23 Cont ID  
Sent By lwagner Date 2013-07-23 Time 13:17 Rev Time 0.00
Received By lwagner Date 2013-07-23 Time 13:07 Sent To  
Notes
***NONE***
Review Stop I INCOMING/PROCESSING
Rev No 5 Status N Date 2013-09-03 Cont ID  
Sent By dharvey Date 2013-09-03 Time 17:17 Rev Time 0.00
Received By dharvey Date 2013-09-03 Time 17:17 Sent To  
Notes
2013-08-31 11:55:03C27
  
  
  
2013-08-29 15:33:16INCOMING SENT TO C25. JW
Review Stop I INCOMING/PROCESSING
Rev No 4 Status N Date 2013-08-26 Cont ID  
Sent By dharvey Date 2013-08-26 Time 08:15 Rev Time 0.00
Received By dharvey Date 2013-07-12 Time 13:16 Sent To  
Notes
2013-08-26 08:16:00PLACED IN DENIED UNDER "K" DH
2013-07-19 13:17:09INCOMING SENT TO C-25
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2013-08-26 Cont ID  
Sent By dharvey Date 2013-08-26 Time 08:16 Rev Time 0.00
Received By dharvey Date 2013-07-12 Time 15:31 Sent To  
Notes
2013-07-18 15:31:23ROUTED NEW PLANS TO C25 WITH PREVIOUS RESUBMITTAL
  
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2013-08-26 Cont ID  
Sent By dharvey Date 2013-08-26 Time 08:16 Rev Time 0.00
Received By dharvey Date 2013-07-12 Time 09:16 Sent To  
Notes
2013-07-15 09:22:47C25
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date 2013-07-03 Cont ID  
Sent By jwitmer Date 2013-07-03 Time 17:25 Rev Time 0.00
Received By jwitmer Date 2013-05-31 Time 18:27 Sent To  
Notes
***NONE***
Review Stop IMPACT COUNTY IMPACT FEES
Rev No 2 Status N Date 2013-08-29 Cont ID  
Sent By jwitmer Date 2013-08-29 Time 15:29 Rev Time 0.00
Received By jwitmer Date 2013-08-29 Time 15:29 Sent To  
Notes
2013-08-29 15:29:48PLANS STAMPED NO FEES DUE. JW
Review Stop IMPACT COUNTY IMPACT FEES
Rev No 1 Status F Date 2013-07-03 Cont ID  
Sent By jwitmer Date 2013-07-03 Time 17:25 Rev Time 0.00
Received By jwitmer Date 2013-07-03 Time 17:25 Sent To  
Notes
2013-07-03 17:25:36BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
 FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
 PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
 A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
 APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
  
 JAMES A. WITMER CBO
 SENIOR COMMERCIAL COMBINATION PLANS EXAMINER
 TEL: 561-805-6715
 FAX: 561-805-6676
 E-MAIL: [email protected]
Review Stop M MECHANICAL (A/C)
Rev No 3 Status P Date 2013-09-03 Cont ID  
Sent By hmoser Date 2013-09-03 Time 11:52 Rev Time 0.00
Received By hmoser Date 2013-09-03 Time 11:08 Sent To  
Notes
2013-09-03 11:52:05PASS PROVISO.
 REVISION REQUIRED FOR ROUGH INSPECTION.
 1) PROVIDE DUCT SIZE FOR OUTSIDE AIR DUCT
 ON 10 TON RTU.
 2) RELOCATED 5 TON RTU AND EXISTING
 3 TON RTU PROVIDE SEPARATE DAMPERS FOR
 OUTSIDE AIR.
 3) PROVIDE SUPPLY GRILLE SIZE ON THE PLANS.
 PLAN REVIEW BY HAROLD MOSER
 [email protected]
 OFFICE 561-805-6732
 FAX 561-805-6676
  
Review Stop M MECHANICAL (A/C)
Rev No 2 Status F Date 2013-07-25 Cont ID  
Sent By hmoser Date 2013-07-25 Time 09:13 Rev Time 0.00
Received By hmoser Date 2013-07-25 Time 08:49 Sent To  
Notes
2013-07-25 09:12:59PLANS DENIED
 REFER TO SECTION 107.3.4.1. PRODUCT APPROVAL,
 MANUFACTURER'S INSTALLATION
 INSTRUCTIONS AND SUBMITTAL ON THE DUCT SOX
 WERE NOT SUBMITTED AS REQUESTED AT FIRST REVIEW.
 2010 FBC.
 PLAN REVIEW BY HAROLD MOSER
 [email protected]
 OFFICE 561-805-6732
 FAX 561-805-6676
Review Stop M MECHANICAL (A/C)
Rev No 1 Status F Date 2013-07-02 Cont ID  
Sent By hmoser Date 2013-07-02 Time 11:34 Rev Time 0.00
Received By hmoser Date 2013-07-02 Time 11:03 Sent To  
Notes
2013-07-02 11:34:21PLANS DENIED
 SUBMIT PRODUCT APPROVAL , MANUFACTURER'S INSTALLATION
 INSTRUCTIONS
 AND SUBMITTAL ON THE DUCT SOX . PER SECTION 107.3.4.1
 2010 FBC.
 PLAN REVIEW BY HAROLD MOSER
 [email protected]
 OFFICE 561-805-6732
 FAX 561-805-6676
Review Stop P PLUMBING
Rev No 2 Status P Date 2013-07-23 Cont ID  
Sent By lwagner Date 2013-07-23 Time 13:17 Rev Time 0.00
Received By lwagner Date 2013-07-23 Time 08:06 Sent To  
Notes
***NONE***
Review Stop P PLUMBING
Rev No 1 Status F Date 2013-06-06 Cont ID  
Sent By lwagner Date 2013-06-06 Time 13:16 Rev Time 0.00
Received By lwagner Date 2013-06-05 Time 09:09 Sent To  
Notes
2013-06-05 09:30:20FBC 2010 ACCESSIBILITY CODE
 FBC 2010 PLUMBING REVIEW #1
 DENIED:
  
 1. IF THE OCCUPANCY TYPE IS A-3, THEN A SERVICE SINK IS
 REQUIRED.
 FBC PLUMBING 2010 TABLE 403.1
  
 2. SHEETS P2.1 & P5.1 IF THE RESTROOM SANITARY IS TWO
 CURCUIT VENT SYSTEMS, A VERTICAL DRY VENT IS REQUIRED
 BETWEEN THE TWO MOST UPSTREAM FLOOR FIXTURES.
 911.2 VENT CONNECTION.
 THE CIRCUIT VENT CONNECTION SHALL BE LOCATED BETWEEN
 THE TWO MOST UPSTREAM FIXTURE DRAINS. THE VENT SHALL
 CONNECT TO THE HORIZONTAL BRANCH AND SHALL BE INSTALLED
 IN ACCORDANCE WITH SECTION 905. THE CIRCUIT VENT PIPE
 SHALL NOT RECEIVE THE DISCHARGE OF ANY SOIL OR WASTE.
  
  
 REVIEW BY
 LARRY WAGNER
 CHIEF PLUMBING INSPECTOR
 PHONE # 805-6692
 EMAIL [email protected]
 FAX # 805-6676
  
Review Stop Z ZONING
Rev No 1 Status N Date 2013-06-03 Cont ID  
Sent By ajones Date 2013-06-03 Time 14:59 Rev Time 0.00
Received By ajones Date 2013-06-03 Time 14:59 Sent To  
Notes
***NONE***


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved