City of West Palm Beach eGovPlus

Plan Review Details - Permit 13010128

Plan Review Stops For Permit 13010128

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2013-01-09			Cont ID
Sent By	tgordon			Date	2013-01-09	Time	12:05	Rev Time	0.00
Received By	tgordon			Date	2013-01-07	Time	14:17	Sent To

Notes

2013-01-07 14:18:25

TO MECHANICAL

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	P	Date	2013-01-30			Cont ID
Sent By	hmoser			Date	2013-01-30	Time	10:01	Rev Time	0.00
Received By	hmoser			Date	2013-01-30	Time	09:40	Sent To

Notes

***NONE***

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2013-01-09			Cont ID
Sent By	tgordon			Date	2013-01-09	Time	12:05	Rev Time	0.00
Received By	tgordon			Date	2013-01-09	Time	11:49	Sent To

Notes

2013-01-09 11:56:20	* CORRECTIONS NEED TO MECHANICAL PLANS*

	1) ENERGY CALCULATIONS SUBMITTED ARE NOT THE COMPLETE
	SET PLEASE SUBMIT THE COMPLETE PRINTED SET OR MEET THE
	EXCEPTION NOTED BELOW. PER 2010 FBC/ENERGY 503.2
	PROVISIONS APPLICABLE TO ALL MECHANICAL SYSTEMS
	(MANDATORY).
	503.2.1 CALCULATION OF HEATING AND COOLING LOADS.
	DESIGN LOADS SHALL BE DETERMINED IN ACCORDANCE WITH THE
	PROCEDURES DESCRIBED IN THE ASHRAE/ACCA STANDARD 183 OR
	ACCA MANUAL N AND SHALL BE ATTACHED TO THE CODE
	COMPLIANCE FORM SUBMITTED TO THE BUILDING DEPARTMENT
	WHEN THE BUILDING IS PERMITTED OR, IN THE EVENT THE
	MECHANICAL PERMIT IS OBTAINED AT A LATER TIME, THE
	SIZING CALCULATION SHALL BE SUBMITTED WITH THE
	APPLICATION FOR THE MECHANICAL PERMIT. HEATING AND
	COOLING LOADS SHALL BE ADJUSTED TO ACCOUNT FOR LOAD
	REDUCTIONS THAT ARE ACHIEVED WHEN ENERGY RECOVERY
	SYSTEMS ARE UTILIZED IN THE HVAC SYSTEM IN ACCORDANCE
	WITH THE ASHRAE HVAC SYSTEMS AND EQUIPMENT HANDBOOK.
	ALTERNATIVELY, DESIGN LOADS SHALL BE DETERMINED BY AN
	APPROVED EQUIVALENT COMPUTATION PROCEDURE, USING THE
	DESIGN PARAMETERS SPECIFIED IN CHAPTER 3.

	EXCEPTION: WHERE MECHANICAL SYSTEMS ARE DESIGNED BY AN
	ENGINEER REGISTERED IN THE STATE OF FLORIDA, THE
	ENGINEER HAS THE OPTION OF SUBMITTING A SIGNED AND
	SEALED SUMMARY SHEET TO THE BUILDING DEPARTMENT IN LIEU
	OF THE COMPLETE SIZING CALCULATION(S). SUCH SUMMARY
	SHEET SHALL INCLUDE THE FOLLOWING (BY ZONE):
	1. PROJECT NAME/OWNER
	2. PROJECT ADDRESS
	3. AREA IN SQUARE FEET
	4. SIZING METHOD USED
	5. OUTDOOR DRY BULB USE
	6. INDOOR DRY BULB
	7. OUTDOOR WET BULB USED
	8. GRAINS WATER (DIFFERENCE)
	9. TOTAL SENSIBLE GAIN
	10. TOTAL LATENT GAIN
	11. RELATIVE HUMIDITY
	12. TOTAL COOLING REQUIRED WITH OUTSIDE AIR
	13. TOTAL HEATING REQUIRED WITH OUTSIDE AIR

	2) PER 2010 FBC 107.2.1 INFORMATION ON CONSTRUCTION
	DOCUMENTS.
	CONSTRUCTION DOCUMENTS SHALL BE DIMENSIONED AND DRAWN
	UPON SUITABLE MATERIAL. ELECTRONIC MEDIA DOCUMENTS ARE
	PERMITTED TO BE SUBMITTED WHEN APPROVED BY THE BUILDING
	OFFICIAL. CONSTRUCTION DOCUMENTS SHALL BE OF SUFFICIENT
	CLARITY TO INDICATE THE LOCATION, NATURE AND EXTENT OF
	THE WORK PROPOSED AND SHOW IN DETAIL THAT IT WILL
	CONFORM TO THE PROVISIONS OF THIS CODE AND RELEVANT
	LAWS, ORDINANCES, RULES AND REGULATIONS, AS DETERMINED
	BY THE BUILDING OFFICIAL.

	3) PER 2010 FBC/B 107.3.5. MINIMUM PLAN REVIEW CRITERIA
	FOR COMMERCIAL BUILDINGS.
	MECHANICAL
	3. EQUIPMENT
	4. EQUIPMENT LOCATION
	5. MAKE-UP AIR
	6. ROOF-MOUNTED EQUIPMENT
	7. DUCT SYSTEMS
	8. VENTILATION
	16. DESIGN FLOOD ELEVATION

	4) EXPLAIN THE USE OF THE BUILDING AND THE FLOOR PLAN
	FOR PROPER PLAN REVIEW.

	5) MECHANICAL PLAN SUBMITTED DOES NOT SHOW IF THE AHU'S
	ARE HANGING OR ON STANDS, WHAT SIZE THE DUCTS ARE,
	LOCATION OF RETURN AIR GRILLS, SUPPLY GRILL SIZES,
	WHERE THE CONDENSATE LINES DRAIN TO, IF THE CONDENSER
	UNITS ARE ON THE ROOF OR SIDE OF BUILDING, HOW THE
	FRESH AIR IS CONNECTING TO THE AHU'S, WHAT'S EXISTING
	AND WHATS NEW, MAKE, MODEL, SIZE, SEER, BTU'S TOTAL &
	SENSIBLE, ETC. OF THE A/C SYSTEMS. CONSTRUCTION
	DOCUMENTS SHALL BE OF SUFFICIENT CLARITY TO INDICATE
	THE LOCATION, NATURE AND EXTENT OF THE WORK PROPOSED
	AND SHOW IN DETAIL THAT IT WILL CONFORM TO THE
	PROVISIONS OF THIS CODE AND RELEVANT LAWS, PER 2010
	CITY OF WPB AMEND. 107.2.1.

	6) IF CONDENSER UNITS ARE ON THE ROOF SUBMIT AN UP TO
	DATE PRODUCT APPROVAL FOR THE A/C CONDENSER STAND.
	FLORIDA DEPARTMENT OF COMMUNITY AFFAIRS RULE 9B-72 JAN.
	1, 2006. (31) SUB-CATEGORY OF PRODUCTS OR CONSTRUCTION
	SYSTEMS THAT WILL REQUIRE PRODUCT APPROVALS: (G)
	EXTERIOR COOLER, FREEZERS & "PER-ENGINEERED A/C
	STANDS".

	7) PROVE OUT DOOR AIR CALCULATIONS AND OUT DOOR AIR,
	PER 2010 FBC/M 403.3.

	8) SHOW COMPLIANCE WITH 2010 FBC/ENERGY 503.2.4.4
	SHUTOFF DAMPER CONTROLS (FOR OUT DOOR AIR INTAKE). BOTH
	OUTDOOR AIR SUPPLY AND EXHAUST DUCTS SHALL BE EQUIPPED
	WITH DAMPERS THAT WILL AUTOMATICALLY SHUT WHEN THE
	SYSTEMS OR SPACES SERVED ARE NOT IN USE.

	MECHANICAL PLAN REVIEW BY:
	TOM GORDON (HY-BYRD INC.) (561) 805-6732