Plan Review Details - Permit 10050571
Plan Review Stops For Permit 10050571
Review Stop B BUILDING (STRUCTURAL)
Rev No 3 Status P Date 2010-07-28 Cont ID  
Sent By jgomez Date 2010-07-28 Time 08:33 Rev Time 0.00
Received By jgomez Date 2010-07-28 Time 08:33 Sent To  
Notes
2010-07-28 08:41:06BUILDING REVISION APPROVED WITH PROVISO:
  
 1- REVISE DESIGN PRESSURES ON SHEET S-1. DESIGN
 PRESSURES SHOWN ON THE 2 STORY SKETCH DON'T MATCH THE
 DESIGN PRESSURES SHOWN UNDER THE TWO STORY WORST CASE
 SCENARIO AND UNDER THE WIND PRESSURES SHOWN FOR THE TWO
 STORY EDGE AND INTERIOR ZONES. SEE COMMENTS ON SHEET
 S-1 SUBMITTED.
  
 2- A) PROVIDE COMPLETE SPECIFICATIONS FOR ELEVATOR TO
 BE INSTALLED.
  
 B) DESIGNER OF RECORD TO REVIEW AND APPROVE SPECS
 PACKAGE PRIOR TO SUBMITTAL.
  
  
  
 ***REMAINDER: PROVIDE INFORMATION REQUESTED ON PROVISO
 DATED 7/01/10. SEE COPY BELOW.
  
  
 1- PROVIDE PRODUCT APPROVAL (2 COPIES) AS REQUIRED BY
 DCA RULE 9B-72 FOR:
 A) ROOF TILE ADHESIVE. TITESET ROOFING ADHESIVE
 SUBMITTED IS NOT LISTED ON THE ROOF TILE NOA. NEED TO
 SHOW WHAT'S THE MIN. ATTACHMENT RESISTANCE TO VERIFY
 COMPLIANCE WITH THE DESIGN PRESSURES OF SEC. R301.
  
 B) SEALOFLEX WATERPROOFING NOA 05-0901.04: ENGINEER
 NEEDS TO REVISE THE RAS 117 CALCULATIONS. THE MIN.
 FASTENER SEPARATION SHALL NOT BE LESS THAN 4"O.C. SEE
 SEC. 8.1 OF RAS 117.
  
 2- ARCHITECT OF RECORD TO REVIEW AND APPROVE IN WRITING
 ALL PRODUCT APPROVALS. SEC. 105.3.3 CITY AMENDMENTS TO
 FBC. THIS APPLIES TO PRODUCT APPROVALS THAT NEED TO BE
 RE-SUBMITTED.
  
 3- SHEET S1: REVISE DESIGN PRESSURES FOR WALL OPENINGS
 IN EXPOSURE "C". REVISE SKETCH FOR ONE STORY ALSO AND
 COORDINATE WITH DESIGN PRESSURES SHOWN AT BOTTOM OF
 PAGE.
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status P Date 2010-07-01 Cont ID  
Sent By jgomez Date 2010-07-01 Time 14:58 Rev Time 0.00
Received By jgomez Date 2010-07-01 Time 14:58 Sent To  
Notes
2010-07-01 15:45:26BUILDING REVIEW APPROVED WITH PROVISO:
  
 1- PROVIDE PRODUCT APPROVAL (2 COPIES) AS REQUIRED BY
 DCA RULE 9B-72 FOR:
 A) ROOF TILE ADHESIVE. TITESET ROOFING ADHESIVE
 SUBMITTED IS NOT LISTED ON THE ROOF TILE NOA. NEED TO
 SHOW WHAT'S THE MIN. ATTACHMENT RESISTANCE TO VERIFY
 COMPLIANCE WITH THE DESIGN PRESSURES OF SEC. R301.
  
 B) SEALOFLEX WATERPROOFING NOA 05-0901.04: ENGINEER
 NEEDS TO REVISE THE RAS 117 CALCULATIONS. THE MIN.
 FASTENER SEPARATION SHALL NOT BE LESS THAN 4"O.C. SEE
 SEC. 8.1 OF RAS 117.
  
 2- ARCHITECT OF RECORD TO REVIEW AND APPROVE IN WRITING
 ALL PRODUCT APPROVALS. SEC. 105.3.3 CITY AMENDMENTS TO
 FBC. THIS APPLIES TO PRODUCT APPROVALS THAT NEED TO BE
 RE-SUBMITTED.
  
 3- SHEET S1: REVISE DESIGN PRESSURES FOR WALL OPENINGS
 IN EXPOSURE "C". REVISE SKETCH FOR ONE STORY ALSO AND
 COORDINATE WITH DESIGN PRESSURES SHOWN AT BOTTOM OF
 PAGE.
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2010-06-10 Cont ID  
Sent By jgomez Date 2010-06-10 Time 11:28 Rev Time 0.00
Received By jgomez Date 2010-06-10 Time 11:28 Sent To PC
Notes
2010-06-10 11:46:04RESIDENTIAL (R3) ADDITION BUILDING REVIEW CHECKLIST.
 2007 FLORIDA RESIDENTIAL CODE WITH 2009 REVISIONS.
  
 1- PROVIDE RECORDED NOTICE OF COMMENCEMENT. SEC. 713.13
 FLORIDA STATUTE.
 ***NOTE: THIS MAY BE RECORDED AT TIME OF PERMIT PICK
 UP.
  
 2- PROVIDE PRODUCT APPROVAL (2 COPIES) AS REQUIRED BY
 DCA RULE 9B-72 FOR:
 A) ROOF TILE ADHESIVE. TILE NOA NOA SUBMITTED CAN'T BE
 USED BECAUSE IT DOESN'T MEET THE DESIGN PRESSURES. SEE
 DESIGN PRESSURES ON TILE NOA. PROVIDE PRODUCT APPROVAL
 FOR ADHESIVE THAT WILL MEET OR EXCEED THE DESIGN
 PRESSURES REQUIRED FOR THIS BUILDING LOCATED ON
 EXPOSURE "C".
  
 B) PRECAST LINTELS AS SPECIFIED ON PLANS.
  
 C) SEALOFLEX WATERPROOFING NOA 05-0901.04: CLEARLY
 IDENTIFY WHICH APPROVED ASSEMBLY IS GOING TO BE USED.
 AND, PROVIDE SIGNED AND SEALED RAS 117 CALCULATIONS AS
 REQUIRED BY GENERAL LIMITATION #7 ON LAST PAGE OF NOA.
  
 3- ARCHITECT OF RECORD TO REVIEW AND APPROVE IN WRITING
 ALL PRODUCT APPROVALS. SEC. 105.3.3 CITY AMENDMENTS TO
 FBC.
  
 4- ARCHITECTURAL PLANS ARE MISSING DETAILS AND
 SPECIFICATIONS FOR ATTIC VENTILATION AS REQUIRED BY
 SEC. R806.
  
 5- SPECIFY ATTIC ACCESS, SIZE AND LOCATION AS REQUIRED
 BY SEC. R807.
  
 6- ARCHITECT TO COORDINATE INSULATION INFORMATION.
 SHEET A0 AND SHEET A2 SPECIFY DIFFERENT TYPE AND
 INSULATION R-VALUE. REVISE AS REQUIRED TO MATCH. ALSO,
 COORDINATE WITH THE ENERGY CALCULATIONS.
  
 7- ARCHITECT TO SPECIFY CARBON MONOXIDE ALARMS ON PLANS
 AS REQUIRED BY SEC. R313.4.
  
 8- ARCHITECT TO REVISE WALL LEGEND ON PLANS TO MATCH
 FLOOR PLANS. EG: MISSING CONCRETE BLOCK CONSTRUCTION ON
 NEW STAIRWAY. REVISE AS REQUIRED. CHECK ALL SHEETS
 WHERE-WALL LEGEND IS SHOWN.
  
 9- OWES $3919.14 FOR PERMIT FEE BALANCE.
  
 10- SHEET A0: REVISE PROJECT INFORMATION. SPECIFY
 CURRENT CODE AND REVISE LEVEL OF ALTERATION. THIS IS
 NOT LEVEL ONE.
  
 11- SHEET A1: A) SPECIFY OPENING WIDTH AT BOTTOM OF
 STAIRS TO VERIFY COMPLIANCE WITH THE EGRESS
 REQUIREMENTS OF SEC. R311.
  
 B) BOTTOM LANDING NEEDS TO COMPLY WITH SEC. R311.5.4.
 THE WIDTH OF EACH LANDING SHALL NOT BE LESS THAN THE
 STAIRWAY SERVED.
  
 12- SHEET A2: SPECIFY DIMENSIONS FOR STAIRS TO VERIFY
 COMPLIANCE OF LANDINGS WITH SEC. R311.5.4. TH3 WIDTH OF
 EACH LANDING SHALL NOT BE LESS THAN THE STAIRWAY
 SERVED.
  
 13- EXTERIOR ELEVATIONS AND ALL TYPICAL WALL SECTIONS.
 REVISE STUCCO THICKNESS FOR FRAMED WALL. 7/8" MIN.
 REQUIRED BY TABLE R702.1(1).
  
 14- SHEET A8: A) REVISE WINDOW AND DOOR BUCK DETAILS.
 BUCK SIZE SPECIFIED NEED TO PROVIDE FULL SUPPORT TO THE
 WINDOW/DOOR FRAMES AS REQUIRED BY SEC. R613.6.
  
 B) CLEARLY SPECIFY ANCHORING OF STRUCTURAL BUCKS.
 COORDINATE WITH INFORMATION GIVEN ON STRUCTURAL
 DRAWINGS.
  
 15- SHEET S1: REVISE DESIGN PRESSURES FOR WALL
 OPENINGS. DESIGN PRESSURES SHOWN DON'T REFLECT DESIGN
 PRESSURES FOR A BUILDING OF EXPOSURE "C" AND THE HEIGHT
 OF THIS STRUCTURE. REVISE AS REQUIRED.
  
 16- SHEET S2: CLEARLY SPECIFY SIZE OF STAIRWAY FOOTING.
 NONE IDENTIFIED ON FOUNDATION PLAN.
  
 17- SHEET S3: CLEARLY IDENTIFY ON FLOOR FRAMING PLAN
 WHICH CONNECTORS FROM THE CONNECTOR SCHEDULE ARE GOING
 TO BE USED. NONE IDENTIFIED ON FRAMING PLANS.
  
 18- SHEET S4:
 A) PROVIDE ROOF FRAMING DETAILS FOR WOOD FRAMED
 CONSTRUCTION. ONLY MASONRY CONSTRUCTION DETAILS WERE
 PROVIDED.
  
 B) CLEARLY MARK ON ROOF FRAMING PLANS ROOF TRUSS
 CONNECTORS TO BE USED. NONE KEYED ON PLANS. KEEP INTO
 CONSIDERATION MASONRY OR WOOD TO WOOD CONNECTORS. EG:
 HGAM10 IS A MASONRY CONNECTOR NOT WOOD TO WOOD
 CONNECTOR. REVISE AS REQUIRED.
  
 19- SPECIFY MATERIAL AND LOCATION OF DRAFSTOPPING ON
 SECOND FLOOR FRAMING PLAN AS REQUIRED BY SEC. R502.1.2.
  
 20- PROVIDE COMPLETE SPECIFICATIONS FOR FLOOR ASSEMBLY
 AT NEW BALCONY.
  
 JULIO GOMEZ
 COMMERCIAL COMBINATION PLANS EXAMINER
 (561)805-6712
Review Stop E ELECTRICAL
Rev No 2 Status P Date 2010-07-21 Cont ID  
Sent By btrobaug Date 2010-07-21 Time 16:24 Rev Time 0.00
Received By btrobaug Date 2010-07-21 Time 06:01 Sent To PC
Notes
***NONE***
Review Stop E ELECTRICAL
Rev No 1 Status P Date 2010-06-02 Cont ID  
Sent By btrobaug Date 2010-06-02 Time 10:57 Rev Time 0.00
Received By btrobaug Date 2010-06-01 Time 13:41 Sent To  
Notes
2010-06-02 11:02:18REVISION REQUIRED
  
 1} 210.52(D), 210.8(A)(1) BATH RECEPTACLES.
  
 2} 210.52(A)(1) GUEST #2 BEDROOM SPACING.
  
 3} 313.13(A) MUST USE THWN IN RISER AND OUTDOOR
 APPLICATIONS.
  
 IF THERE ARE ANY QUESTIONS PLEASE CALL.
  
 BILL TROBAUGH
 ELECTRICAL PLANS EXAMINER
 CITY OF WEST PALM BEACH
 561/805-6718
  
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2010-07-07 Cont ID  
Sent By lmartine Date 2010-07-07 Time 16:32 Rev Time 0.00
Received By lmartine Date 2010-07-07 Time 16:32 Sent To  
Notes
2010-07-07 16:32:35IN ZONING BOX
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2010-06-23 Cont ID  
Sent By vmolina Date 2010-06-23 Time 10:57 Rev Time 0.00
Received By vmolina Date 2010-06-23 Time 10:57 Sent To  
Notes
2010-06-23 11:03:25R-20
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date 2010-06-11 Cont ID  
Sent By lfranco Date 2010-06-10 Time 18:41 Rev Time 0.00
Received By lmartine Date 2010-05-20 Time 09:30 Sent To  
Notes
2010-05-20 09:30:44R23
  
Review Stop IMPACT COUNTY IMPACT FEES
Rev No 1 Status N Date 2010-06-08 Cont ID  
Sent By jgomez Date 2010-06-08 Time 17:01 Rev Time 0.00
Received By jgomez Date 2010-06-08 Time 17:01 Sent To  
Notes
2010-06-08 17:03:58NO REQUIRED FOR OVER 3,600 S.F. HOUSE.
Review Stop M MECHANICAL (A/C)
Rev No 2 Status P Date 2010-07-01 Cont ID  
Sent By jgomez Date 2010-07-01 Time 17:32 Rev Time 0.00
Received By jgomez Date 2010-07-01 Time 17:32 Sent To  
Notes
2010-07-01 17:37:54MECHANICAL REVIEW APPROVED WITH PROVISO:
  
 1- CFM'S CALCULATED ON THE MANUAL J CALCULATIONS AND
 CFM'S SPECIFIED ON DRAWING M1 DON'T MATCH. REVISE AS
 REQUIRED TO MATCH.
  
Review Stop M MECHANICAL (A/C)
Rev No 1 Status F Date 2010-06-08 Cont ID  
Sent By jgomez Date 2010-06-08 Time 17:04 Rev Time 0.00
Received By jgomez Date 2010-06-08 Time 17:04 Sent To  
Notes
2010-06-08 17:12:07RESIDENTIAL (R3) ADDITION, MECHANICAL REVIEW CHECKLIST.
 2007 FLORIDA RESIDENTIAL CODE WITH 2009 REVISIONS.
  
 1- DRAWING M1 NEEDS TO BE SIGNED AND SEALED BY THE
 ARCHITECT AS REQUIRED BY CHAPTER 481 FLORIDA STATUTE.
  
 2- CFM'S CALCULATED ON THE MANUAL J CALCULATIONS AND
 CFM'S SPECIFIED ON DRAWING M1 DON'T MATCH. REVISE AS
 REQUIRED TO MATCH.
  
 3- CONDENSING UNIT MOUNTING DETAIL INFORMATION IS NOT
 CLEAR AND REVISE CITED CODE SECTION. CLEARLY SPECIFY
 STRAPS SIZE AND FASTENERS SIZE (DIAMETER AND LENGTH) TO
 BE USED TO VERIFY COMPLIANCE WITH THE DESIGN PRESSURES
 OF SEC. R301. AND, CORRECT CODE SECTION TO USE IS SEC.
 M1307.3. SEE 2007 FLORIDA RESIDENTIAL CODE AND REVISE
 AS REQUIRED.
  
 JULIO GOMEZ
 COMMERCIAL COMBINATION PLANS EXAMINER
 (561)805-6712
Review Stop P PLUMBING
Rev No 2 Status P Date 2010-07-01 Cont ID  
Sent By jgomez Date 2010-07-01 Time 17:53 Rev Time 0.00
Received By jgomez Date 2010-07-01 Time 17:52 Sent To  
Notes
***NONE***
Review Stop P PLUMBING
Rev No 1 Status P Date 2010-06-10 Cont ID  
Sent By jgomez Date 2010-06-10 Time 08:59 Rev Time 0.00
Received By jgomez Date 2010-06-10 Time 08:59 Sent To  
Notes
***NONE***
Review Stop Z ZONING
Rev No 4 Status P Date 2010-08-02 Cont ID  
Sent By lfranco Date 2010-08-02 Time 17:54 Rev Time 0.00
Received By lfranco Date 2010-08-02 Time 17:54 Sent To E
Notes
***NONE***
Review Stop Z ZONING
Rev No 3 Status P Date 2010-07-16 Cont ID  
Sent By lfranco Date 2010-07-16 Time 18:18 Rev Time 0.00
Received By lfranco Date 2010-07-09 Time 13:49 Sent To I
Notes
***NONE***
Review Stop Z ZONING
Rev No 2 Status F Date 2010-07-02 Cont ID  
Sent By lfranco Date 2010-07-02 Time 16:50 Rev Time 0.00
Received By lfranco Date 2010-07-02 Time 16:50 Sent To B
Notes
2010-07-02 16:52:04PLANNING AND ZONING: *** FAILED, COMMENT WAS NOT
 ADDRESSED. COPIES OF SURVEYS WERE NOT SUBMITTED. ***
  
 1. RESPOND TO COMMENTS IN WRITING. NOTE: THE SUBMITTAL
 OF THE REQUESTED INFORMATION MAY GENERATE ADDITIONAL
 COMMENTS.
  
  
 2. PROVIDE TWO (2) COPIES OF A CURRENT SURVEY, WHICH
 INCLUDES THE PROPERTY'S ADDRESS AND LEGAL DESCRIPTION.
 SHOW SETBACK DIMENSIONS FROM ALL PROPERTY LINES.
  
 IF YOU HAVE ANY QUESTIONS PLEASE CONTACT ME.
  
 LINDA MIA FRANCO
 SENIOR PLANNER
 PLANNING AND ZONING DEPARTMENT
 TEL: (561) 822-1443
 EMAIL: [email protected]
  
Review Stop Z ZONING
Rev No 1 Status F Date 2010-06-10 Cont ID  
Sent By lfranco Date 2010-06-10 Time 18:41 Rev Time 0.50
Received By lfranco Date 2010-06-10 Time 18:41 Sent To I
Notes
2010-06-10 18:42:15PLANNING AND ZONING:
  
 1. RESPOND TO COMMENTS IN WRITING. NOTE: THE SUBMITTAL
 OF THE REQUESTED INFORMATION MAY GENERATE ADDITIONAL
 COMMENTS.
  
  
 2. PROVIDE TWO (2) COPIES OF A CURRENT SURVEY, WHICH
 INCLUDES THE PROPERTY'S ADDRESS AND LEGAL DESCRIPTION.
 SHOW SETBACK DIMENSIONS FROM ALL PROPERTY LINES.
  
 IF YOU HAVE ANY QUESTIONS PLEASE CONTACT ME.
  
 LINDA MIA FRANCO
 SENIOR PLANNER
 PLANNING AND ZONING DEPARTMENT
 TEL: (561) 822-1443
 EMAIL: [email protected]
  


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved