City of West Palm Beach eGovPlus

Plan Review Details - Permit 09020194

Plan Review Stops For Permit 09020194

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2009-07-28			Cont ID
Sent By	jwitmer			Date	2009-07-28	Time	13:55	Rev Time	0.80
Received By	jwitmer			Date	2009-07-28	Time	13:02	Sent To

Notes

2009-07-28 13:34:44	BUILDING PLAN REVIEW
	PERMIT: 09020194
	ADD: 309 CLEMATIS ST.
	CONT: PLAN REVIEW / VON ESSELBORN
	TEL: (561)951-6729

	FL BLD CODE= 2007 FLORIDA BUILDING CODE
	W/ 2009 FBC SUPPLEMENTS
	* WEST PALM BEACH AMENDMENTS

	2ND REVIEW
	ACTION: DENIED

	1) PLANS SUBMITTED FOR PERMIT (FIRST TIME REVIEW) AFTER
	MARCH 1ST, 2009 SHALL BE REVIEWED TO THE 2007 FBC
	BUILDING WITH 2009 SUPPLEMENTS.

	2) MISSING ARCHITECTURAL SHEETS, THERE IS NO
	INFORMATION ON THE KITCHEN AS TO FLOOR, WALL NOR
	CEILING FINISHES, THICKNESS OF FINSIHES NOR FIRE RAING
	OF FINISHES.
	106.3.5.1.1 MINIMUM PLAN REVIEW CRITERIA FOR COMMERCIAL
	BUILDINGS:
	(5) FIRE SUPRESSION SYSTEMS
	(9) ROOF/ WALL & FLOOR INSULATION
	(11) INTERIOR REQUIREMENTS SHALL INCLUDE FLAME SPREAD
	AND SMOKE DEVELOPMENT
	LIGHT AND VENTILATION
	(12) SPECIAL SYSTEMS: POSIBLE LIFTS

	3) MASTER PLAN 08060519 SHEET A-8.1 INDICATES FUTURE
	ROOF EXHAUST FAN, NO INFORMATION WAS SUBMITTED FOR THE
	ROOF CURB, FAN EXHAUST ASSEMBLY, FOR WIND. PLEASE
	SSUBMIT STRUCTURAL INFORMATION HOW THE FAN WILL BE
	ATTACHED TO THE STRUCTURAL COMPONENTS OF THE BUILDING.
	COMPONENTS AND CLADDING. 106.3.5.1.1(8) STRUCTURAL
	REQUIREMENTS.

	4) FL BLD CODE 1609.6.2.2 COMPONENTS & CLADDING,
	PROVIDE 2 COPIES,
	3 IF THRESHOLD OR RESIDENT INSPECTOR OF PRODUCT TESTING
	REPORTS, MISSING REPORTS ARE AS FOLLOWS:
	4A) EXHAUST FANS
	4B) PRE-MANUFACTURED A/C STANDS

	301.13 FBC MECHANICAL. WIND RESISTANCE. MECHANICAL
	EQUIPMENT, APPLIANCES AND SUPPORTS THAT ARE EXPOSED TO
	WIND SHALL BE DESIGNED AND INSTALLED TO RESIST WIND
	PRESSURES ON THE EQUIPMENT AND THE SUPPORTS AS
	DETERMINED IN ACCORDANCE WITH THE FLORIDA BUILDING
	CODE, BUILDING.

	5) 106.3.3 PRODUCT APPROVALS. THOSE PRODUCTS WHICH ARE
	REGULATED BY THE DCA RULE 9B-72 SHALL BE REVIEWED AND
	APPROVED IN WRITTING BY THE DESIGNER OF RECORD PRIOR TO
	SUBMITTAL FOR JURISDICTIONAL APPROVAL.


	A THOROUGH REVIEW CAN NOT BE MADE AT THIS TIME, AS A
	RESULT OF THE ADDITIONAL INFORMATION REQUESTED
	ADDITIONAL COMMENTS MAY APPEAR THAT WERE NOT PART OF
	THIS REVIEW.


	INFORMATIONAL: WHEN RESUBMITTING PLANS PLEASE INDICATE
	THE REVISION & REMOVE & REPLACE ANY PAGES AS NECESSARY.
	A TRANSMITTAL LETTER LISTING THE ORIGINAL REVIEW
	COMMENT NUMBER, WITH A DESCRIPTION OF THE REVISION
	MADE, IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE
	THE CHANGES CAN BE FOUND WILL HELP TO EXPEDITE YOUR
	PERMIT. THANK YOU FOR YOUR ANTICIPATED COOPERATION.

	JIM WITMER C. B. O.
	BUILDING PLAN REVIEW II

	TEL: (561)805-6715
	FAX: (561)805-6731
	E-MAIL: [email protected]
	SURVEY:
	WWW.SURVEYMONKEY.COM/WESTPALMBEACHCONSTRUCTIONSERVICES

	PLEASE NOTE: FLORIDA HAS A VERY BROAD PUBLIC RECORDS
	LAW. WRITTEN COMMUNICATIONS TO OR FROM LOCAL OFFICIALS
	REGARDING CITY BUSINESS ARE PUBLIC RECORD, AVAILABLE TO
	THE PUBLIC UPON REQUEST. YOUR E-MAIL COMMUNICATIONS ARE
	THEREFORE SUBJECT TO PUBLIC DISCLOSURE.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2009-03-06			Cont ID
Sent By	shill			Date	2009-03-06	Time	09:01	Rev Time	0.00
Received By	shill			Date	2009-03-06	Time	09:01	Sent To

Notes

2009-03-06 09:12:49	**CORRECTIONS**
	**PLAN CHECK ONLY**

	SAMANTHA HILL, BUILDING PLANS EXAMINER
	561-805-6724 [email protected]

	FBC FLORIDA BUILDING CODE 2004
	FBC EB FLORIDA BUILDING CODE 2004 EXISTING BUILDING
	CODE
	FBC R FLORIDA BUILDING CODE 2004 RESIDENTIAL
	FBC* CITY OF WEST PALM BEACH AMENDMENTS TO THE FBC2004
	FAC FLORIDA ADMINISTRATIVE CODE
	FS FLORIDA STATUTE

	1. NO BUILDING PLANS SUBMITTED. HOWEVER, COVER SHEET
	PROVIDES BUILDING INFORMATION AND STATES THAT THIS AREA
	IS "PROPOSED" BUT CALLS THE OPEN AIR DINING AREA AND
	GAZEBO DINING AREA "EXISTING." ISN'T THIS KITCHEN AREA
	UNDER THE SAME STATUS AS THE OPEN AIR DINING AND GAZEBO
	DINING; STRUCTURE PERMITTED AND THE BUILDOUT IN PLAN
	REVIEW? AS STATED, THIS APPEARS TO BE AN ADDITION.

	2. GOVERNING CODE EFFECTIVE MARCH 1, 2009 IS FBC2007
	WITH 2009 SUPPLEMENTS.

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2009-03-12			Cont ID
Sent By	btrobaug			Date	2009-03-12	Time	10:03	Rev Time	0.00
Received By	btrobaug			Date	2009-03-10	Time	15:34	Sent To

Notes

2009-03-12 10:03:42

	THE ELECTRICAL PLANS APPEAR TO BE IN COMPLIANCE WITH
	THE 2005 NEC. THE REVIEW WILL BE CHANGED FROM FAIL TO
	PASS PENDING A CONTRACTOR APPLYING FOR A PERMIT WITH
	THE SAME PLANS. NOTE THE 2007 FBC BECAME EFFECTIVE
	3/1/09. THE 2005 NEC IS STILL IN EFFECT..

	IF THERE ARE ANY QUESTIONS PLEASE CALL.

	BILL TROBAUGH
	ELECTRICAL PLANS EXAMINER
	CITY OF WEST PALM BEACH
	561/805-6718

Review Stop	ENG		ENGINEERING CSD
Rev No	1	Status	Date		Cont ID
Sent By			Date	Time	Rev Time
Received By			Date	Time	Sent To

Notes

***NONE***

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2009-04-07			Cont ID
Sent By	mcarsill			Date	2009-04-07	Time	15:47	Rev Time	0.00
Received By	mcarsill			Date	2009-04-07	Time	15:37	Sent To

Notes

2009-04-07 15:47:11	ROXY'S KITCHEN
	309 CLEMATIS STREET
	PERMIT NUMBER 09020194

	1. SEPARATE PLANS AND PERMITS REQUIRED FOR THE
	INSTALLATION OF FIRE ALARM EQUIPMENT SHOWN ON PAGE E-2.
	SOME SMOKE DETECTORS SHOWN SHOULD BE REPLACED WITH HEAT
	DETECTORS DUE TO THEIR CLOSE PROXIMITY TO COOKING
	EQUIPMENT OR TO ITEMS THAT MAY PRODUCE STEAM.

	2. SEPARATE PLANS AND PERMITS REQUIRED FOR THE
	INSTALLATION OF THE HOOD, DUCT, AND FIRE SUPPRESSION
	SYSTEM.

	3. PLEASE PROVIDE DETAILS ON THE GAS FIRE BOWLS SHOWN
	ON PAGE P-1. CUT SHEETS NEED TO BE PROVIDED ON THE
	DEVICES. WHAT SAFETY DEVICES ARE INSTALLED ON THESE
	BOWLS. ON APRIL 7, 2009, SPOKE TO WHITNEY OFFIELD
	REGARDING THESE FIRE BOWLS. SHE WILL ATTEMPT TO OBTAIN
	INFORMATION ON THESE.

	4. ON PAGE M-1 TWO DIFFERENT DUCT SIZES ARE SHOWN.
	PLEASE COORDINATE THE EXHAUST DUCT HOOD ELEVATION AND
	THE MECHANICAL PLAN DIAGRAM.

	5. THE EXHAUST FAN DISPLAYED ON PAGE M-1 SHALL BE
	PROPERLY SEPARATED FROM ANY DOORS, WINDOWS, AND
	PROPERTY LINES BY A MINIMUM OF AT LEAST 10 FEET.

	6. THE FIRE SUPPRESSION SYSTEM SHALL BE A WET CHEMICAL
	SYSTEM THAT COMPLIES WITH THE UL 300 STANDARD AND
	APPROPRIATE NFPA STANDARDS.

	7. THE MANUAL PULL STATION SHALL BE INSTALLED IN A
	MEANS OF EGRESS.

	8. NO HORIZONTAL OR VERTICAL PIPE PENETRATIONS ARE
	ALLOWED TO BE INSTALLED WITHIN STAIR # 2.

	MIKE CARSILLO, BATTALION CHIEF
	BUREAU OF FIRE PREVENTION

Review Stop	G			GAS REVIEW
Rev No	1	Status	F	Date	2009-03-12			Cont ID
Sent By	kstevens			Date	2009-03-12	Time	11:55	Rev Time	0.00
Received By	kstevens			Date	2009-03-12	Time	11:55	Sent To

Notes

2009-03-12 12:32:16	DENIED
	REFERENCE:
	FBC-2004 FUEL GAS

	1. SHT P-2 GAS DISTRIBUTION ISOMETRIC. A LISTED SHUT
	OFF VALVE SHALL BE INSTALLED IMMEDIATELY AHEAD OF EACH
	MP REGULATOR. SECTION 409.4. A UNION IS REQUIRED
	DOWNSTREAM OF THE SHUT OFF VALVE NEAR THE REGULATOR FOR
	SERVICING & REPLACEMENT.

	2. SHT P-2 GAS DISTRIBUTION ISOMETRIC. INDICATE THE
	TOTAL BTU'S FOR THE EXISTING KITCHEN & DISTANCE TO THE
	MOST REMOTE OUTLET IN THE KITCHEN ON THE RISER DIAGRAM.
	SECTION 106.1.2 MORE INFORMATION REQUIRED AND SECTION
	402 PIPE SIZING.

	3. SHT P-2 GAS DISTRIBUTION ISOMETRIC. NOTE REFERENCES
	GAS PIPE SIZE PER TABLE 402.4(20) P.E. PIPE. PLEASE
	INDICATE WHERE THE P.E. PIPE WILL BE INSTALLED. (P.E.
	FOR OUTDOOR UNDERGROUND ONLY). SECTION 404.14.1.

	4. SHT P-2 GAS DISTRIBUTION ISOMETRIC. PLEASE INDICATE
	GAS TYPE. (IF LP GAS MORE COMMENTS WILL BE
	FORTHCOMING).

	5. SHT P-2 GAS DISTRIBUTION ISOMETRIC. A MANUAL SHUT
	OFF VALVE IS REQUIRED UPSTREAM OF THE EMERGENCY HOOD
	SHUT DOWN SHUT OFF VALVE.

	6. SHT P-2 GAS DISTRIBUTION ISOMETRIC. SUBMIT MANUF.
	SPECIFICATION SHEETS FOR THE UNIONS. INDICATE MODEL
	NUMBER AND SHOW BTU CAPACITY FOR TOTAL LOAD OF ALL
	APPLIANCES COMBINED. SECTION 410.2(1)(2)(3).

	WHEN RESUBMITTING PLANS PLEASE INDICATE
	THE REVISION & REMOVE & REPLACE ANY
	PAGES AS NECESSARY. A TRANSMITTAL LETTER
	LISTING THE ORIGINAL REVIEW COMMENT NUMBER,
	WITH A DESCRIPTION OF THE REVISION MADE,
	IDENTIFYING THE SHEET OR SPECIFICATION
	PAGE WHERE THE CHANGES CAN BE FOUND
	WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE
	ALL VOID SHEETS FROM ALL PLANS AND PLACE
	ONE SET OF THEM LOOSELY ON TOP OF THE
	COLLATED PLANS TO BE REVIEWED.
	THANK YOU FOR YOUR ANTICIPATED COOPERATION.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date				Cont ID
Sent By				Date	2009-04-07	Time		Rev Time	0.00
Received By	adarroug			Date	2009-02-12	Time	09:01	Sent To

Notes

2009-02-12 09:02:17

TO "COMM" BD#6

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2009-03-26			Cont ID
Sent By	rregueir			Date	2009-03-26	Time	09:04	Rev Time	0.00
Received By	rregueir			Date	2009-03-25	Time	20:40	Sent To

Notes

2009-03-26 09:04:08	REVIEW #: 1ST PLAN CHECK ONLY
	ACTION: DENIED

	FBC 2007 CODE FAMILY W/ 2009 SUPPLEMENTS
	FBC CH.1 AS AMENDED BY THE CITY OF WEST PALM BEACH

	THIS PLAN HAS BEEN REVIEWED FOR COMPLIANCE WITH THE
	ABOVE LISTED CODES. PLEASE MAKE THE FOLLOWING
	CORRECTIONS PRIOR TO RESUMITTING PLANS:

	1. WHAT IS THE DISTANCE OF THE KITCHEN EXHAUST FAN FROM
	ADJACENT BUILDING AND PROPERTY LINE? EXHAUST OUTLETS
	SHALL BE LOCATED NOT LESS THAN 10 FEET HORIZONTALLY
	FROM PARTS OF THE SAME OR CONTIGUOUS BUILDINGS,
	ADJACENT BUILDINGS, ADJACENT PROPERTY LINES AND AIR
	INTAKE OPENINGS INTO ANY BUILDING IN ACCORDANCE WITH
	FBC-M 506.3.12.3.

	2. TYPE I HOOD SYSTEMS SHALL BE DESIGNED AND INSTALLED
	TO AUTOMATICALLY ACTIVATE THE EXHAUST FAN WHENEVER
	COOKING OPERATIONS OCCUR IN ACCORDANCE WITH FBC-M
	507.2.1.1. THE ACTIVATION OF THE EXHAUST FAN SHALL
	OCCUR THROUGH AN INTERLOCK WITH THE COOKING APPLIANCES,
	BY MEANS OF HEAT SENSORS OR BY MEANS OF OTHER APPROVED
	METHODS IN ACCORDANCE WITH THIS SECTION.

	3. FAN APPEARS TO BE NEXT TO THE ROOF EDGE. GUARDS
	SHALL BE PROVIDED WHERE FANS OR OTHER COMPONENTS THAT
	REQUIRE SERVICE ARE LOCATED WITHIN 10 FEET OF A ROOF
	EDGE IN ACCORDANCE WITH FBC-M 304.10. THE GUARD SHALL
	EXTEND NOT LESS THAN 30 INCHES BEYOND EACH END OF THE
	FAN AND THE TOP OF THE GUARD SHALL BE LOCATED NOT LESS
	THAN 42 INCHES ABOVE THE ELEVATED SURFACE ADJACENT TO
	THE GUARD. THE GUARD SHALL BE CONSTRUCTED IN ACCORDANCE
	WITH THE REQUIREMENTS FOR GUARDS SPECIFIED IN THE
	FLORIDA BUILDING CODE, BUILDING.

	4. THE PLAN SHOWS THE MANUAL PULL STATION (ACTUATION
	DEVICE) NEXT TO THE HOOD. THE MANUAL ACTUATION DEVICE
	SHALL BE LOCATED AT OR NEAR A MEANS OF EGRESS FROM THE
	COOKING AREA A MINIMUM OF 10 FEET AND A MAXIMUM OF 20
	FEET FROM THE KITCHEN EXHAUST SYSTEM IN ACCORDANCE WITH
	FBC-B 904.11.1. THE MANUAL ACTUATION DEVICE SHALL BE
	INSTALLED NOT MORE THAN 48 INCHES OR LESS THAN 42
	INCHES ABOVE THE FLOOR AND SHALL CLEARLY IDENTIFY THE
	HAZARD PROTECTED.

	5. EXHAUST FAN AND CURB SHALL BE DESIGNED AND INSTALLED
	FOR WIND RESISTANCE IN ACCORDANCE WITH FBC-M 301.12.
	PROVIDE MANUFACTURER???S DATA FOR FAN WIND RESISTANCE
	AND ATTACHMENT DETAIL FOR CURB-TO-BUILDING AND
	FAN-TO-CURB.

	6. PLAN SHOWS MAKE-UP AIR DUCTS FOR KITCHEN EXHAUST BUT
	THE SOURCE OF THE MAKE-UP AIR AND THE MAKE-UP AIR FAN
	ARE NOT SHOWN ON PLANS. THE EXHAUST AND MAKEUP AIR
	SYSTEMS SHALL BE ELECTRICALLY INTERLOCKED TO INSURE
	THAT MAKEUP AIR IS PROVIDED WHENEVER THE EXHAUST SYSTEM
	IS IN OPERATION. MAKEUP AIR INTAKE OPENING LOCATIONS
	SHALL COMPLY WITH SECTIONS 401.4 AND 401.4.1 IN
	ACCORDANCE WITH FBC-M 508.1.

	7. FLOOR PLAN SHOWS THE KITCHEN EXHAUST DUCT AS 12X12
	WHILE THE ELEVATION PLAN SHOWS THE EXHAUST DUCT AS
	10X12. WHICH IS CORRECT? PLEASE CLARIFY.

	8. THE ELEVATION PLAN CALLS FOR A 24X14 FIRE RATED
	CHASE FOR A 10X12 DUCT. THE ELEVATION PLAN REFERENCES
	ARCHITECTURAL PLAN FOR CHASE DETAIL. NO ARCHITECTURAL
	PLANS WERE PROVIDED FOR THIS REVIEW. WHILE THIS
	ENCLOSURE MAY OR MAY NOT BE REQUIRED BY CODE (SEE
	SECTION 506.3.6 FOR CLEARANCE REQUIREMENTS AND 506.3.10
	FOR DUCT ENCLOSURE REQUIREMENTS), THE SIZES SHOWN ON
	PLANS WOULD NOT PROVIDE THE REQUIRED MINIMUM CLEARANCES
	FOR A DUCT ENCLOSURE. THE ENCLOSURE SHALL BE SEPARATED
	FROM THE DUCT BY A MINIMUM OF 6 INCHES AND A MAXIMUM OF
	12 INCHES IN ACCORDANCE WITH FBC-M 506.3.10. THIS
	ENCLOSURE SHALL ALSO BE VENTED TO THE OUTSIDE OF THE
	BUILDING THROUGH THE USE OF WEATHER-PROTECTED OPENINGS.

	9. NO INFORMATION WAS PROVIDED REGARDING THE PROPOSED
	WALK-IN COOLER. PROVIDE MANUFACTURER???S SUBMITTAL DATA
	AND SHOW THE LOCATION OF ALL RELATED EQUIPMENT
	(INCLUDING REMOTE CONDENSER), PIPING AND CONDENSATE
	DISPOSAL IN ACCORDANCE WITH FBC-M 304.1 AND FBC-B
	106.1.1.

	IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:
	RONALD J. REGUEIRO
	561.805.6719
	[email protected]

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2009-03-12			Cont ID
Sent By	kstevens			Date	2009-03-12	Time	11:55	Rev Time	0.00
Received By	kstevens			Date	2009-03-12	Time	11:55	Sent To

Notes

2009-03-12 12:30:52	DENIED
	REFERENCE:
	FBC-2004 PLUMBING
	FBC-2004 FUEL GAS
	FBC-2004 CHAPTER 1
	CITY WPB MUNICIPAL CODE

	1. SHT P-2 SANITARY, (GREASE), RISER DIAGRAM. THE DISH
	WASHER SHALL DISCHARGE VIA A SEPARATE LINE, (SANITARY).
	ARTICLE III SECTION 90-124(7)(B).

	2. SHT P-2 SANITARY, (GREASE), RISER DIAGRAM. THE
	COMBINATION DRAIN & VENT SYSTEM SHALL BE PROVIDED WITH
	A DRY VENT CONNECTED AT ANY POINT WITHIN THE SYSTEM.
	SECTION 912.2.2. SYSTEM NOT VENTED.

	3. SHT P-2 POTABLE WATER RISER DIAGRAM. A WATER HAMMER
	ARRESTOR IS REQUIRED AT THE DISH WASHER. SECTION 604.9.

	4. SHT P-2 GAS DISTRIBUTION ISOMETRIC. A LISTED SHUT
	OFF VALVE SHALL BE INSTALLED IMMEDIATELY AHEAD OF EACH
	MP REGULATOR. SECTION 409.4. A UNION IS REQUIRED
	DOWNSTREAM OF THE SHUT OFF VALVE NEAR THE REGULATOR FOR
	SERVICING & REPLACEMENT.

	5. SHT P-2 GAS DISTRIBUTION ISOMETRIC. INDICATE THE
	TOTAL BTU'S FOR THE EXISTING KITCHEN & DISTANCE TO THE
	MOST REMOTE OUTLET IN THE KITCHEN ON THE RISER DIAGRAM.
	SECTION 106.1.2 MORE INFORMATION REQUIRED AND SECTION
	402 PIPE SIZING.

	6. SHT P-2 GAS DISTRIBUTION ISOMETRIC. NOTE REFERENCES
	GAS PIPE SIZE PER TABLE 402.4(20) P.E. PIPE. PLEASE
	INDICATE WHERE THE P.E. PIPE WILL BE INSTALLED. (P.E.
	FOR OUTDOOR UNDERGROUND ONLY). SECTION 404.14.1.

	7. SHT P-2 GAS DISTRIBUTION ISOMETRIC. PLEASE INDICATE
	GAS TYPE. (IF LP GAS MORE COMMENTS WILL BE
	FORTHCOMING).

	8. SHT P-2 GAS DISTRIBUTION ISOMETRIC. A MANUAL SHUT
	OFF VALVE IS REQUIRED UPSTREAM OF THE EMERGENCY HOOD
	SHUT DOWN SHUT OFF VALVE.

	9. SHT P-2 GAS DISTRIBUTION ISOMETRIC. SUBMIT MANUF.
	SPECIFICATION SHEETS FOR THE UNIONS. INDICATE MODEL
	NUMBER AND SHOW BTU CAPACITY FOR TOTAL LOAD OF ALL
	APPLIANCES COMBINED. SECTION 410.2(1)(2)(3).

	WHEN RESUBMITTING PLANS PLEASE INDICATE
	THE REVISION & REMOVE & REPLACE ANY
	PAGES AS NECESSARY. A TRANSMITTAL LETTER
	LISTING THE ORIGINAL REVIEW COMMENT NUMBER,
	WITH A DESCRIPTION OF THE REVISION MADE,
	IDENTIFYING THE SHEET OR SPECIFICATION
	PAGE WHERE THE CHANGES CAN BE FOUND
	WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE
	ALL VOID SHEETS FROM ALL PLANS AND PLACE
	ONE SET OF THEM LOOSELY ON TOP OF THE
	COLLATED PLANS TO BE REVIEWED.
	THANK YOU FOR YOUR ANTICIPATED COOPERATION.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 805-6731
	E-MAIL [email protected]

Review Stop	Z			ZONING
Rev No	1	Status	N	Date	2009-03-12			Cont ID
Sent By	mflis			Date	2009-03-12	Time	10:30	Rev Time	0.00
Received By	mflis			Date	2009-03-12	Time	10:30	Sent To

Notes

2009-03-12 10:33:02	ZONING REVIEW: NOT REQUIRED

	** THIS SUBMITTAL INCLUDES MEP ONLY
	** SEE ALTERNATE ARCHITECTURAL PROJECT SUBMITTAL FOR
	ZONING COMMENTS RELATED TO THIS PROJECT

	MATT FLIS - 822-1445