Home Records and Reports Contractor Records Owner Records Permit Records Permit Reports Business Reports Property Records Business Tax My Account Code Enforcement Contact Us Log In/Out Print Plan Review Stops For Permit 08070320 Review Stop B BUILDING (STRUCTURAL) Rev No 15 Status P Date 2009-08-21 Cont ID   Sent By rbrown Date 2009-08-21 Time 11:05 Rev Time 0.00 Received By rbrown Date 2009-08-21 Time 11:05 Sent To   Notes 2009-08-21 11:06:57 SUBMITTAL ON 7/09/09 FOR STRUCTURAL INTEGRITY OF   PACKAGE UNITS SUBJECT TO WIND LOADS. Review Stop B BUILDING (STRUCTURAL) Rev No 14 Status F Date 2009-06-25 Cont ID   Sent By rbrown Date 2009-06-25 Time 19:52 Rev Time 0.00 Received By rbrown Date 2009-06-25 Time 19:52 Sent To   Notes 2009-06-25 20:16:41 BUILDING PLAN REVIEW   *******DENIED*******   ROBERT BROWN (561) 805 6652   E-MAIL: [email protected]       FBC = FLORIDA BUILDING CODE 2004   FBC*= FLORIDA BUILD'G CODE (CITY AMEND)   F.S.= FLORIDA (STATE) STATUTE       SUBMITTAL ON 6/22/09 FOR STRUCTURAL WIND LOAD INTEGRITY   OF PACKAGE UNITS.       1) FBCM 301.13 MECHANICAL UNITS EXPOSED TO WIND. FOR   THE SANYO OUTDOOR UNITS THE FIFTH PAGE (UNNUMBERED) OF   THE CALCULATION REPORT ONLY ADDRESSES AND SPECIFIES THE   SCREWS REQUIRED FOR ATTACHMENT OF THE UNIT TO IT'S   "BOTTOM PLATE ASSEMBLY". THE REPORT GOES ON TO SHOW   EXPLODED VIEWS OF THE UNIT CONSTRUCTION BUT THE   CALCULATIONS DO NOT ADDRESS THE REQUIREMENT TO SHOW   THAT THE EXTERNAL (VERTICAL AND HORIZONTAL) PANELS OF   THE UNIT WILL RETAIN THEIR INTEGRITY AND REMAIN   ATTACHED TO THE UNIT WHEN SUBJECT TO THE WIND PRESSURES   RESULTING FROM 140 MPH WIND SPEED (3 SECOND GUST).   THERE ARE NO CALCULATIONS FOR THE SCREWS/FASTENERS   HOLDING THE PANELS TOGETHER, AND THERE ARE NO   CALCULATIONS FOR THE PANELS THEMSELVES (SHEAR AT HOLES   BASED ON HOLE SIZE AND EDGE DISTANCE , ETC.). AS SUCH   THE SUBMITTED CALCULATIONS DO NOT ADDRESS THE 12/17/08   PROVISO GIVEN BY RON REGUEIRO, MECHANICAL PLANS   EXAMINER II. THE MECHANICAL CODE SECTION REQUIRES THAT   THE APPLIANCE ITSELF BE DESIGNED AND INSTALLED TO   RESIST THE WIND PRESSURES. SUBMIT MANUFACTURER'S TEST   DATA OR STRUCTURAL CALCULATIONS TO SHOW THAT THE   PACKAGE UNIT HAS BEEN TESTED OR DESIGNED FOR THE WIND   PRESSURES RESULTING FROM 140 MPH WIND SPEED (3 SECOND   GUST). THE PROVISO GIVEN BY THE MECHANICAL PLANS   EXAMINER ON 12/17/08 STATED THIS SAME REQUIREMENT,   QUOTE: "PROVIDE MANUFACTURER'S SUBMITTAL DATA SHOWING   OUTDOOR APPLIANCES ARE DESIGNED TO RESIST WIND   PRESSURES IN ACCORDANCE WITH FBCM 301.13."       2) 471.025 F.S. AND 61G15-23.002 FL. ADMINISTRATIVE   CODE. ONLY THE COVER PAGE OF BOTH CALCULATION REPORTS   IS SIGNED AND SEALED. WHEN SUBMITTING CALCULATION   REPORTS THE ENGINEER MUST EITHER SIGN AND SEAL EACH   SHEET OR PROVIDE A SIGNED AND SEALED CONTENTS PAGE   WHICH REFERENCES THE SHEET NUMBER OF EACH SHEET IN THE   CALCULATION REPORT.       **QUOTE PERMIT# ON ALL CORRESPONDENCE**       END OF REVIEW COMMENTS   THE CODE REFERENCES GIVE ADDITIONAL INFO   TELEPHONE: (561) 805 6652 ROBERT BROWN   E-MAIL: [email protected] Review Stop B BUILDING (STRUCTURAL) Rev No 13 Status P Date 2009-06-19 Cont ID   Sent By shill Date 2009-06-19 Time 11:43 Rev Time 0.00 Received By shill Date 2009-06-19 Time 11:43 Sent To   Notes 2009-06-19 11:44:18 CAVITY SHAFT WALL SUBMITTAL     Review Stop B BUILDING (STRUCTURAL) Rev No 12 Status P Date 2009-06-10 Cont ID   Sent By shill Date 2009-06-10 Time 13:05 Rev Time 0.00 Received By shill Date 2009-06-10 Time 13:05 Sent To   Notes 2009-06-10 13:06:13 REVISION A001CR2     Review Stop B BUILDING (STRUCTURAL) Rev No 11 Status P Date 2009-05-14 Cont ID   Sent By rbrown Date 2009-05-14 Time 20:34 Rev Time 0.00 Received By rbrown Date 2009-05-14 Time 20:34 Sent To   Notes 2009-05-14 20:35:42 SUBMITTAL ON 4/27/09 FOR FIRESTOPPING RATED ASSEMBLIES. Review Stop B BUILDING (STRUCTURAL) Rev No 10 Status F Date 2009-05-14 Cont ID   Sent By rbrown Date 2009-05-14 Time 19:53 Rev Time 0.00 Received By rbrown Date 2009-05-14 Time 19:53 Sent To   Notes 2009-05-14 20:09:33 BUILDING PLAN REVIEW   *******DENIED*******   ROBERT BROWN (561) 805 6652   E-MAIL: [email protected]       FBC = FLORIDA BUILDING CODE 2004   FBC*= FLORIDA BUILD'G CODE (CITY AMEND)   F.S.= FLORIDA (STATE) STATUTE       SUBMITTAL ON 4/27/09 FOR TIE DOWN CABLES ON PACKAGE   UNIT.       1) FBCM 301.13 MECHANICAL UNITS EXPOSED TO WIND. ONLY   TIE DOWN CABLES ARE BEING PROPOSED. THAT DOES NOT   ADDRESS THE 12/17/08 PROVISO GIVEN BY RON REGUEIRO,   MECHANICAL PLANS EXAMINER II. THE MECHANICAL CODE   SECTION REQUIRES THAT THE APPLIANCE ITSELF BE DESIGNED   AND INSTALLED TO RESIST THE WIND PRESSURES. SUBMIT   MANUFACTURER'S TEST DATA OR STRUCTURAL CALCULATIONS TO   SHOW THAT THE PACKAGE UNIT HAS BEEN TESTED OR DESIGNED   FOR THE WIND PRESSURES RESULTING FROM 140 MPH WIND   SPEED (3 SECOND GUST). THE PROVISO GIVEN BY THE   MECHANICAL PLANS EXAMINER ON 12/17/08 STATED THIS SAME   REQUIREMENT, QUOTE: "PROVIDE MANUFACTURER'S SUBMITTAL   DATA SHOWING OUTDOOR APPLIANCES ARE DESIGNED TO RESIST   WIND PRESSURES IN ACCORDANCE WITH FBCM 301.13."       **QUOTE PERMIT# ON ALL CORRESPONDENCE**       END OF REVIEW COMMENTS   THE CODE REFERENCES GIVE ADDITIONAL INFO   TELEPHONE: (561) 805 6652 ROBERT BROWN   E-MAIL: [email protected] Review Stop B BUILDING (STRUCTURAL) Rev No 9 Status P Date 2009-04-02 Cont ID   Sent By shill Date 2009-04-02 Time 18:03 Rev Time 0.00 Received By shill Date 2009-04-02 Time 18:03 Sent To   Notes 2009-04-02 18:04:36 REVISION   A101CR5, A103CR4,106CR3, A118CR5, A119CR5, A120CR5,   A901CR5     Review Stop B BUILDING (STRUCTURAL) Rev No 8 Status P Date 2009-04-02 Cont ID   Sent By shill Date 2009-04-02 Time 09:01 Rev Time 0.00 Received By shill Date 2009-04-02 Time 09:01 Sent To   Notes 2009-04-02 09:19:17 REVISION, CHANGE ROOF SYSTEM (STANDING SEAM) ON SOME   PORTIONS OF PROJECT       SUBMITTALS; ROOF SHOPS AND LIGHT POLE CALCULATIONS Review Stop B BUILDING (STRUCTURAL) Rev No 7 Status F Date 2009-03-30 Cont ID   Sent By shill Date 2009-03-30 Time 10:51 Rev Time 0.00 Received By shill Date 2009-03-30 Time 10:50 Sent To   Notes 2009-03-30 10:52:09 ****CORRECTIONS****       SAMANTHA HILL, BUILDING PLANS EXAMINER   561-805-6724 [email protected]       FBC FLORIDA BUILDING CODE 2004   FBC EB FLORIDA BUILDING CODE 2004 EXISTING BUILDING   CODE   FBC R FLORIDA BUILDING CODE 2004 RESIDENTIAL   FBC* CITY OF WEST PALM BEACH AMENDMENTS TO THE FBC2004   FAC FLORIDA ADMINISTRATIVE CODE   FS FLORIDA STA       1. PLEASE HAVE ALL SUBMITTALS/SHOP DRAWINGS REVIEWED BY   DESIGNER OF RECORD PRIOR TO SUBMITTAL. FAC61G15-23,   FAC61G1. Review Stop B BUILDING (STRUCTURAL) Rev No 6 Status P Date 2009-03-09 Cont ID   Sent By shill Date 2009-03-09 Time 18:35 Rev Time 0.00 Received By shill Date 2009-03-09 Time 18:35 Sent To   Notes 2009-03-09 18:40:21 REVISION ADDRESSING BUILDING AND ELECTRIC   PROVISOS/REDLINES:       A101CR4, A118CR4, A120CR4, A123CR1, A901CR4       SUBJECT TO FIRE & ELECTRIC REVIEWS       RECEIVED SHOP DRAWING REVIEW LETTER FROM DOR (PROVISO   ITEM), 1 LETTER FILED, 1 STAMPED & RETURNED TO CONTR   WITH CALCS (STAMPED PREVIOUS REVIEW)         Review Stop B BUILDING (STRUCTURAL) Rev No 5 Status P Date 2009-02-25 Cont ID   Sent By shill Date 2009-02-25 Time 17:12 Rev Time 0.00 Received By shill Date 2009-02-25 Time 17:12 Sent To   Notes 2009-02-25 17:17:47 REVISION DATED 2/6/9 SHEETS A101CR3, A103CR3, A106CR2,   A110CR2, A113CR3, A118CR3, A119CR3, A120CR3, A901CR3       **PROVISO**   ALL SUBMITTALS & DELEGATED ENGINEERING TO BE REVIEWED   BY DOR; SUBMIT LETTER   ** ISSUED AT CONTRACTOR???S RISK   PLAN REDLINED; 1 HR CORRIDOR REQUIRED AT EGRESS STAIR   SUBMIT REVISION (CHANGE WALL DESIGNATION AT THIS AREA   TO REFLECT   CONSTRUCTION OF 1 HR WALLS, PER ARCHITECT)         Review Stop B BUILDING (STRUCTURAL) Rev No 4 Status P Date 2008-12-08 Cont ID   Sent By shill Date 2008-12-08 Time 16:00 Rev Time 0.00 Received By shill Date 2008-12-08 Time 16:00 Sent To   Notes 2008-12-08 16:01:08 **PROVISO** - REVISE AS FOLLOWS, PRIOR TO INSTALLATION       WBCM SUBMITTAL #8, CALCULATIONS CM MANUFACTURING,   PLEASE ADDRESS:       A. ASCE7-05 REFERENCED; FBC2004 REQUIRES ASCE7-02. THIS   CAN BE DONE WITH A LETTER OR CAN BE A PROVISO ITEM.       B. SEE PAGE 22, EXPOSURE B USED WITH AN IMPORTANCE   FACTOR OF .77. IF ACCEPTABLE TO THE DESIGNER OF RECORD,   THE REDUCED IMPORTANCE FACTOR CAN BE USED BUT PROVIDE   JUSTIFICATION FOR USE OF EXPOSURE B. THIS JOB APPEARS   TO HAVE EXPOSURE C CONDITIONS, FBC1609.4.       C. CALCS AND PLANS DO NOT NEED TO BE REVISED, BUT   PLEASE NOTE THAT GOVERNING CODE IS FBC2004 WITH 2007   REVISIONS/SUPPLEMENTS. CALCS REFER TO 2005 AND 2006   REVISIONS AND SUPPLEMENTS, PLANS STATE COMPLIANCE WITH   INTERNATIONAL BUILDING CODE 2003. FOR FUTURE   SUBMITTALS, PLEASE REVISE.       D. PAGE 21 NOTE STATES "LATERAL IMPACT DOES NOT ALLOW   1/3 STRESS INCREASE AS ALLOWED FOR ASD WIND LOAD   ANALYSIS" PLEASE PROVIDE MORE INFORMATION REGARDING   STRESS INCREASE USED AND SEE FBC1605.3.1.1 AND CLARIFY   USE OF STRESS INCREASE.         Review Stop B BUILDING (STRUCTURAL) Rev No 3 Status F Date 2008-11-21 Cont ID   Sent By shill Date 2008-11-21 Time 11:33 Rev Time 0.00 Received By shill Date 2008-11-20 Time 07:58 Sent To   Notes 2008-11-21 11:40:45 SAMANTHA HILL, BUILDING PLANS EXAMINER   561-805-6724 [email protected]   FBC FLORIDA BUILDING CODE 2004   FBC EB FLORIDA BUILDING CODE 2004 EXISTING BUILDING   CODE   FBC R FLORIDA BUILDING CODE 2004 RESIDENTIAL   FBC* CITY OF WEST PALM BEACH AMENDMENTS TO THE FBC2004   FAC FLORIDA ADMINISTRATIVE CODE   FS FLORIDA STATUTE       1-79. ADDRESSED.       80. PLEASE SHOW COMPLIANCE WITH FBC910, SMOKE AND HEAT   VENTS. PROVIDE CALCULATIONS ON THE PLAN AND SHOW   COMPLIANCE WITH ALL REQUIREMENTS.       THE REQUEST FOR CONSIDERATION UNDER ALTERNATE MATERIALS   AND METHODS HAS BEEN FORWARDED TO ROBERT BROWN FOR   REVIEW. THIS REVIEW WILL REMAIN IN FAILED STATUS UNTIL   HIS DECISION. IF THIS REQUEST IS DENIED, THIS REVIEW   WILL BE PASSED WITH PROVISO TO REVISE DESIGN TO INCLUDE   THE REQUIRED SMOKE AND HEAT VENTS. IF APPROVED, A   PASSED STATUS WILL BE ENTERED FOR THIS REVIEW.       81-87. ADDRESSED.       88. **PROVISO** - REVISE AS FOLLOWS, PRIOR TO   INSTALLATION       WBCM SUBMITTAL #8, CALCULATIONS CM MANUFACTURING,   PLEASE ADDRESS:       A. ASCE7-05 REFERENCED; FBC2004 REQUIRES ASCE7-02. THIS   CAN BE DONE WITH A LETTER OR CAN BE A PROVISO ITEM.       B. SEE PAGE 22, EXPOSURE B USED WITH AN IMPORTANCE   FACTOR OF .77. IF ACCEPTABLE TO THE DESIGNER OF RECORD,   THE REDUCED IMPORTANCE FACTOR CAN BE USED BUT PROVIDE   JUSTIFICATION FOR USE OF EXPOSURE B. THIS JOB APPEARS   TO HAVE EXPOSURE C CONDITIONS, FBC1609.4.       C. CALCS AND PLANS DO NOT NEED TO BE REVISED, BUT   PLEASE NOTE THAT GOVERNING CODE IS FBC2004 WITH 2007   REVISIONS/SUPPLEMENTS. CALCS REFER TO 2005 AND 2006   REVISIONS AND SUPPLEMENTS, PLANS STATE COMPLIANCE WITH   INTERNATIONAL BUILDING CODE 2003. FOR FUTURE   SUBMITTALS, PLEASE REVISE.       D. PAGE 21 NOTE STATES "LATERAL IMPACT DOES NOT ALLOW   1/3 STRESS INCREASE AS ALLOWED FOR ASD WIND LOAD   ANALYSIS" PLEASE PROVIDE MORE INFORMATION REGARDING   STRESS INCREASE USED AND SEE FBC1605.3.1.1 AND CLARIFY   USE OF STRESS INCREASE.         Review Stop B BUILDING (STRUCTURAL) Rev No 2 Status F Date 2008-11-06 Cont ID   Sent By shill Date 2008-11-06 Time 12:22 Rev Time 0.00 Received By shill Date 2008-10-29 Time 10:56 Sent To   Notes 2008-11-06 12:22:30 SAMANTHA HILL, BUILDING PLANS EXAMINER   561-805-6724 [email protected]   FBC FLORIDA BUILDING CODE 2004   FBC EB FLORIDA BUILDING CODE 2004 EXISTING BUILDING   CODE   FBC R FLORIDA BUILDING CODE 2004 RESIDENTIAL   FBC* CITY OF WEST PALM BEACH AMENDMENTS TO THE FBC2004   FAC FLORIDA ADMINISTRATIVE CODE   FS FLORIDA STATUTE       1-29. ADDRESSED.       30. ADDRESSED.       31C. PAGE 4 OF THE CALCULATIONS, OTHER SHEETS, PLANS,   REFER TO 2004 FLORIDA STATE BUILDING CODE; PLEASE   REVISE TO GOVERNING CODE WHICH IS FLORIDA BUILDING CODE   2004 WITH 2007 REVISIONS/SUPPLEMENTS.       2ND REVIEW, PLANS AND CALCS STILL STATE 2004 FLORIDA   STATE BUILDING CODE; THIS SHOULD STATE FLORIDA BUILDING   CODE OR FBC 2004 (WITH 2007 REVISIONS/SUPPLEMENTS).       E. ALL SIGNED AND SEALED SHEETS ARE TO INCLUDE ALL   INFORMATION REQUIRED BY FAC61G15-23.002.       2ND REVIEW, A NUMBER WAS INCLUDED BUT THIS NUMBER WAS   ISSUED TO VP CONSOLIDATED HOLDINGS, INC. THE COMPANY ON   THE PLANS IS VP BUILDINGS, INC. I WAS UNABLE TO FIND A   DBA, AND HAVE CONTACTED FBPE TO DETERMINE WHETHER OR   NOT THIS IS ACCEPTABLE. ALSO, VP CONSOLIDATED HOLDINGS,   INC. HAVE FILED A WITHDRAWAL STATING THAT THEY WILL NO   LONGER DO BUSINESS IN FLORIDA. HAS ADDITIONAL PAPERWORK   BEEN FILED WHICH I AM UNABLE TO LOCATE ON THE INTERNET?   COMPLIANCE WITH FS471.023(1) IS NOT CLEAR.   HTTP://WWW.SUNBIZ.ORG/PDF/15259987.PDF       32?39. ADDRESSED.       40. (INFORMATIONAL) THE 3 RING BINDER ENTITLED   TECHNICAL SPECIFICATIONS WILL BE INCLUDED WITH THE   RECORD SET WITH THE PROVISO IN ACCORDANCE WITH FBC2004   AND PLAN. NO ACTION REQUIRED.       41-43. ADDRESSED.       44. SEE FBC TABLE 1016.1, CORRIDORS 203 AND 205 FROM   VISITOR'S GALLERY TO STAIRS TO HAVE 1 HOUR FIRE   RESISTIVE RATING AND THEREFORE DOORS 203 1, 204 1, 205   1, 206 1, 200 1, TO BE RATED IN ACCORDANCE WITH   FBC715.3.       2ND REVIEW, AS DISCUSSED WITH ENGINEER, THIS ITEM WILL   BE ADDRESSED IN RESUBMITTAL. NOTE THAT SOME DOORS FROM   FIRST REVIEW WERE REMOVED, SO THERE IS ONLY ONE   CORRIDOR FROM MEZZANINE LEVEL. AS DISCUSSED, THE   CORRIDOR STARTS AT THE DOOR (MEANS OF EGRESS STAIR   HALLWAY TO VIEWING GALLERY) AND TERMINATES AT THE EXIT,   GROUND FLOOR (CORRIDOR MUST TERMINATE AT AN EXIT, WHICH   IN THIS CASE IS THE EXIT DISCHARGE), SO ALTHOUGH THIS   IS NOT A RATED EXIT STAIR, THE STAIR IS CONTAINED IN A   1 HOUR CORRIDOR. PLEASE CONTACT ME IF YOU WISH TO   DISCUSS.       45-54. ADDRESSED.       55. FBC13-101.1, ENERGY CALCS REQUIRED FOR BOTH THE   MAIN BUILDING AND FOR THE SCALE HOUSE.       2ND REVIEW, ENERGY CALCS SUBMITTED. FOR THE MAIN   BUILDING, 2 DOORS ARE SHOWN. ISN'T THE WALL BETWEEN THE   ADMIN AREA AND PROCESSING TO BE TREATED AS A WALL,   INCLUDED IN THE INPUT DATA REPORT, AND THE DOORS NOTED?   I WAS UNABLE TO LOCATE MEZZANINE WINDOWS IN THE INPUT   DATA REPORT. THE SLAB IS NOTED AS 6.38 R VALUE; PLEASE   CLARIFY. THE ROOF ON THE ENERGY CALC IS SHOWN AS 32.8 R   VALUE, PLAN (SEE DETAIL 9 A110CR1) SPECIFIES R19 BATT.   IF THE PEMB ROOF INCLUDES INSULATION, PLEASE PROVIDE   THIS INFORMATION ON THE PLAN. NOTE THAT THE TYPED NAME   AND LICENSE NUMBER OF THE ARCHITECT FOR CERTIFICATION   BY THE ARCHITECT IS ACCEPTABLE ON THE ENERGY CALC IN   LIEU OF SIGNATURE IF ALL INFORMATION IS INCLUDED ON THE   PLAN FBC13-103.1.1.1. PLEASE CONFIRM INPUT DATA   REQUIREMENTS AND REVISE AS NECESSARY. THIS LIST IS NOT   BE COMPREHENSIVE; PLEASE CHECK ALL.       56-58. ADDRESSED.       59. SEE FBC1016.4, AIR MOVEMENT IN CORRIDORS. PLEASE   REMOVE SUPPLY, RETURN, EXHAUST, RELIEF OR VENTILATION   AIR DUCTS FROM EXIT ACCESS CORRIDORS, SEE OTHER   COMMENTS. PLEASE NOTE THAT THERE ARE TWO HALLS IN THE   MEZZANINE WHICH SERVE AS CORRIDORS.       2ND REVIEW, ONE DOOR WAS REMOVED, SO ONLY ONE CORRIDOR   SERVING THE MEZZANINE REMAINS. PLEASE REVISE PLANS IN   ACCORDANCE WITH FBC1016.4, SEE ALSO OTHER COMMENTS   REGARDING 1 HOUR FIRE RATING REQUIRED.       60-61. ADDRESSED.       62. A114C, SPECIFY GUARD PICKET SPACING FBC1012.       A114 WAS REVISED TO SPECIFY 4IN, BUT THIS IS TO RESIST   A 4IN OBJECT (REQUIRES SPACING LESS THAN 4IN). THIS CAN   BE A REDLINE ITEM IF REQUESTED.       63. ADDRESSED.       64. SEE 3 A007C, THE HANDRAIL IS NOT CONTINUOUS. A106C   HANDRAIL EXTENSIONS AT BOTTOM IS NOT SHOWN. PLEASE   PROVIDE DETAILS AND CORRELATE A SHEETS.       2ND REVIEW, THE ELEVATION ON A106C DOES NOT SHOW THE   EXTENSION REQUIRED, FBC11-4.9.4(2). AT THE BOTTOM, THE   HANDRAIL SHALL CONTINUE TO SLOPE FOR THE DISTANCE OF   WIDTH OF ONE TREAD FROM THE BOTTOM RISER, THE REMAINDER   OF THE EXTENSION WILL BE HORIZONTAL, FBC FIGURE 19(D).   SEE ALSO DETAIL 1 113, A A007 (BOTTOM). THE EXTENSIONS   ARE SHOWN CORRECTLY IN OTHER DETAILS. PLEASE CHECK ALL.       65-72. ADDRESSED.       73. SHOW LOCATION OF STROBES, FBC11-4.28.1.       2ND REVIEW, PLEASE ADD TO BATHROOM 108, TRUCKER?S   BATHROOM. PLEASE CONFIRM THAT STROBES ARE SHOWN IN ALL   LOCATIONS REQUIRED.       74-76. ADDRESSED.       77. PROVIDE A SPECIFICATION FOR ATTACHMENT OF THE   BACKING FOR THE GRAB BARS (A111C) TO SHOW COMPLIANCE   WITH FBC1607.7.1.1, FBC11-4.26.3. DETAIL STATES SCREWED   TO STUD BUT DOES NOT SPECIFY SIZE OF SCREWS OR DISTANCE   APART, DOES NOT SPECIFY A WIDTH FOR THE 22G SHEET METAL   BACKING.       2ND REVIEW, SPECIFICATION NOT PROVIDED. THIS CAN BE A   PROVISO ITEM; PROVIDE SHOPS BEFORE INSTALLATION. THIS   WILL BE REDLINED TO INCLUDE CONCENTRATED LOAD   REQUIREMENT OF 250 PLF 1607.7.2.       78-79. ADDRESSED.       80. PLEASE SHOW COMPLIANCE WITH FBC910, SMOKE AND HEAT   VENTS. PROVIDE CALCULATIONS ON THE PLAN AND SHOW   COMPLIANCE WITH ALL REQUIREMENTS.       THE REQUEST FOR CONSIDERATION UNDER ALTERNATE MATERIALS   AND METHODS HAS BEEN FORWARDED TO ROBERT BROWN FOR   REVIEW.       81-85. ADDRESSED.       NEW COMMENTS (NEW SUBMITTALS) ? PLEASE NOTE THAT   SUBMITTALS ARE NOT REQUIRED AT THIS TIME; THEY CAN BE   SUBMITTED PRIOR TO INSTALLATION:       86. **THIS SUBMITTAL CAN BE A PROVISO ITEM (SUBMIT   BEFORE INSTALLATION)**   ASSOCIATED ENGINEERING INCORPORATED IS TO HAVE A   CERTIFICATE OF AUTHORIZATION, FS471 (WBCM SUBMITTAL   #7). "AUTH # PENDING" WAS WRITTEN ON THE SHEETS   PREPARED BY RONALD T. FOSS, P.E. FOR THE SORT   ENCLOSURES, BUT THIS COMPANY NAME CANNOT BE USED UNTIL   THE NUMBER IS ISSUED. THE WEBSITE DOES NOT INDICATE   THAT AN APPLICATION IS PENDING. ARE THESE SHEETS   REQUIRED AT THIS TIME? CAN THEY BE SUBMITTED AFTER A   COFA HAS BEEN OBTAINED? A SET HAS BEEN RETAINED. PLEASE   INFORM MR. FOSS OF THE REQUIREMENT TO OBTAIN THIS   CERTIFICATE AND PLEASE HAVE HIM SEND AN EMAIL   CONFIRMING HIS UNDERSTANDING.       87. **THIS SUBMITTAL CAN BE A PROVISO ITEM (SUBMIT   BEFORE INSTALLATION)**   THE STRUCTURAL CALCULATIONS EQUIPMENT TIE-DOWN AND   CONNECTIONS TO ROOF STRUCTURE (WBCM SUBMITTAL #12) DOES   NOT INCLUDE A TITLE BLOCK, FAC61G15-23.002.       88. **THIS SUBMITTAL CAN BE A PROVISO ITEM (SUBMIT   BEFORE INSTALLATION)**   WBCM SUBMITTAL #8, CALCULATIONS, PLEASE ADDRESS:       A. ASCE7-05 REFERENCED; FBC2004 REQUIRES ASCE7-02. THIS   CAN BE DONE WITH A LETTER OR CAN BE A PROVISO ITEM.       B. SEE PAGE 22, EXPOSURE B USED WITH AN IMPORTANCE   FACTOR OF .77. IF ACCEPTABLE TO THE DESIGNER OF RECORD,   THE REDUCED IMPORTANCE FACTOR CAN BE USED BUT PROVIDE   JUSTIFICATION FOR USE OF EXPOSURE B. THIS JOB APPEARS   TO HAVE EXPOSURE C CONDITIONS, FBC1609.4.       C. CALCS AND PLANS DO NOT NEED TO BE REVISED, BUT   PLEASE NOTE THAT GOVERNING CODE IS FBC2004 WITH 2007   REVISIONS/SUPPLEMENTS. CALCS REFER TO 2005 AND 2006   REVISIONS AND SUPPLEMENTS, PLANS STATE COMPLIANCE WITH   INTERNATIONAL BUILDING CODE 2003. FOR FUTURE   SUBMITTALS, PLEASE REVISE.       D. PAGE 21 NOTE STATES "LATERAL IMPACT DOES NOT ALLOW   1/3 STRESS INCREASE AS ALLOWED FOR ASD WIND LOAD   ANALYSIS" PLEASE PROVIDE MORE INFORMATION REGARDING   STRESS INCREASE USED AND SEE FBC1605.3.1.1 AND CLARIFY   USE OF STRESS INCREASE.         Review Stop B BUILDING (STRUCTURAL) Rev No 1 Status F Date 2008-08-08 Cont ID   Sent By shill Date 2008-08-08 Time 15:08 Rev Time 0.00 Received By shill Date 2008-08-08 Time 15:08 Sent To   Notes 2008-08-08 15:09:20 ****PRIVATE PROVIDER AUDIT****       SAMANTHA HILL, BUILDING PLANS EXAMINER   561-805-6724 [email protected]   FBCFLORIDA BUILDING CODE 2004   FBC EBFLORIDA BUILDING CODE 2004 EXISTING BUILDING   CODE   FBC RFLORIDA BUILDING CODE 2004 RESIDENTIAL FBC*   CITY OF WEST PALM BEACH AMENDMENTS TO THE FBC2004 FAC   FLORIDA ADMINISTRATIVE CODE   FSFLORIDA STATUTE       1. THE OWNER'S ACKNOWLEDGEMENT IS REQUIRED,   FS553.791(4)(C).       2.THE PRIVATE PROVIDER AFFIDAVIT IS TO IDENTIFY THE   PLANS REVIEWED.THERE WAS A LOG PROVIDED, BUT THIS LOG   IS NOT A PART OF THE AFFIDAVIT.THE AFFIDAVIT STATES   "77 PAGES - ATTACHED" BUT NOTHING WAS ATTACHED; THE LOG   WAS SUBMITTED SEPARATELY.THE LOG DOES NOT PROPERLY   IDENTIFY EACH SHEET (SOME SHEETS HAVE DIFFERENT PAGE,   FOR INSTANCE E106CR1, M104C, M014C) AND THE LOG DOES   NOT IDENTIFY THE PLAN SHEETS BY DATE.NOT ALL SHEETS   WERE STAMPED BY GFA (E106CR1, S101CR1).IT APPEARS   THAT THE FIRE PROTECTION PLANS WERE NOT REVIEWED, OR   THE C SHEETS (WHICH SHOW COMPLIANCE WITH FBC11 AND FBC5   REQUIREMENTS), BUT THIS IS REQUIRED BY   FBC*106.3.5.1.1(5), FS553.79 (2).NOTE THAT THE   FOUNDATION PERMIT HAS NOT YET BEEN ISSUED, SO CANNOT BE   USED TO SHOW CODE COMPLIANCE FOR THIS PLAN.       3. FIRE SPRINKLER PLANS REQUIRED.AT A MINIMUM, A HEAD   LAYOUT IS TO BE SUBMITTED, SEE FBC*106.3.5.1.1(5),   FS553.79(2), LETTER FROM DCA (AVAILABLE UPON REQUEST).       4. M SHEETS, THE SEAL IS TO INCLUDE THE DATE,   FAC61G15-23.002, FS471.       5. PLEASE NOTE THAT AN INDEX SHEET IS USEFUL WITH A   PLAN OF THIS SIZE.THIS IS NOT A REQUIREMENT, BUT A   SUGGESTION TO ASSIST WITH PLAN REVIEW.PROVIDING AN   INDEX SHEET WILL ENABLE PLAN REVIEWERS TO OBTAIN   NECESSARY INFORMATION MORE QUICKLY, WHICH WILL HELP TO   EXPEDITE THE PLAN REVIEW PROCESS AND CUT DOWN ON PLAN   REVIEW TIME.       6. TWO 8 1/2 X 11 SHEETS WERE SUBMITTED.NEITHER ARE   SEALED, ONE HAS THE DESIGNER'S TITLE BLOCK BUT IS   LACKING SOME OF THE INFORMATION REQUIRED BY   FAC61G15-23.002; THE OTHER IS NOT SEALED.PLEASE   INCORPORATE THESE CHANGES INTO THE SIGNED AND SEALED   PLAN.       7. N/A.       8. FBC* 109.3.7RESIDENT INSPECTOR. SUBMIT INSPECTOR   RESUME' AND LICENSE DOCUMENTS TO KEN CONRAD,   561-805-6666.A RESIDENT INSPECTOR PROGRAM IS   REQUIRED, ON THIS PROJECT (STEEL STRUCTURE ONLY), DUE   TO ONE OR MORE OF THE FOLLOWING:   - BUILDINGS/ADDITIONS OF TYPE I OR II   CONSTRUCTION   - ANY MAJOR STRUCTURAL ALTERATIONS   - STRUCTURES IN WHICH THE CONCRETE   DESIGN IS BASED ON COMPRESSIVE   STRENGTH (F'C) IN EXCESS OF 3000 PSI   - PILE DRIVING   - BUILDINGS OVER 20,000 SQFT IN AREA   - BUILDINGS OVER 2 STORIES IN HEIGHT   - BUILDING/STRUCTURES OF UNUSUAL DESIGN OR METHODS   OF CONSTRUCTION       ALSO, PLEASE ARRANGE WITH KEN CONRAD (CHIEF BUILDING   INSPECTOR - TEL: 561 805 6666), A MEETING INVOLVING THE   OWNER, RESIDENT INSPECTOR, JOB INSPECTOR, CONTRACTOR   AND ENGINEER.THIS MUST BE DONE PRIOR TO PERMIT   ISSUANCE.THREE ORIGINAL SETS OF ALL DOCUMENTS ARE   REQUIRED FOR PERMITTING.       9. A901C, SECTION 507.2 UNLIMITED AREA NOT APPLICABLE   TO THIS PROJECT AS THIS IS A MIXED USE, A3 AND S1   DECLARED.FBC507.9 UNLIMITED AREA FOR A4 OCCUPANCY   REQUIRES THAT THE FINISHED FLOOR BE 12? FROM GRADE   LEVEL AND HAS OTHER REQUIREMENTS FOR EXITING.I WAS   UNABLE TO LOCATE AN ALLOWANCE FOR A3 UNLIMITED AREA,   TYPE IIB.SEE FBC TABLE 503 AND CHAPTER 5.       10. SEE FBC302.3; THIS IS A MIXED OCCUPANCY BUILDING.   PLEASE SEE FBC302.3.2 REGARDING BUILDING RATIOS.IT   APPEARS THAT THIS BUILDING HAS BEEN DESIGNED IN   ACCORDANCE WITH FBC302.3.1 BUT DOES NOT COMPLY WITH THE   MORE STRINGENT REQUIREMENT OF A3, TYPE IIB.SEE OTHER   COMMENTS.       11. IF AREA MODIFICATIONS ARE USED FOR SPRINKLERS OR   OPEN AREA, PLEASE INCLUDE ALL CALCULATIONS ON THE PLAN.   FBC506.       12. A901C STATES THAT THE MEZZANINE COMPLIES WITH   FBC505.PLEASE SHOW COMPLIANCE BY STATING THE TOTAL   SQUARE FOOT AREA OF THE MEZZANINE, FBC505.2.       13. A901C, S1 AND A3 DECLARED, EMPLOYEE BREAK ROOM   SHOWN AS ACCESSORY, BUT THE ADMINISTRATION (BUSINESS)   AREAS, FIRST FLOOR AND MEZZANINE, WERE NOT ADDRESSED.   DECLARE TOTAL SF AREA FOR ADMINISTRATION AND SHOW   COMPLIANCE WITH FBC302.FIRE RESISTIVE RATED   CONSTRUCTION MAY BE REQUIRED BETWEEN THE B AND S AND B,   S AND A OCCUPANCIES (MEZZANINE).       14. A901C, DECLARE SQUARE FOOT AREA FOR THE ASSEMBLY   AND S1 OCCUPANCIES, ACCESSORY BREAK ROOM, FBC1004,   FBC302.ALSO SEE OTHER COMMENT; DECLARE SF AREA FOR   THE BUSINESS (ADMINISTRATION) AREA SHOWN ON THE FIRST   FLOOR AS WELL AS THE OFFICE IN THE MEZZANINE.IT IS   NOT CLEAR IF THIS IS ACCESSORY OR INCIDENTAL OR MIXED   OCCUPANCY, FBC302.       15. IS THE LUBE & OIL ROOM USED AS A REPAIR GARAGE,   FBC406.6, MAINTENANCE OR REPAIR OF AUTOMOTIVE OR   SIMILAR EQUIPMENT?SHOW COMPLIANCE ON THE PLAN WITH   SPECIAL REQUIREMENTS, IF ANY.       16. DO ANY OF THE AREAS INCLUDE HIGH PILED OR RACK   STORAGE OF COMBUSTIBLES, FBC413.3?SHOW COMPLIANCE ON   THE PLAN FOR ANY SPECIAL REQUIREMENTS, IF ANY.   17. THERE ARE SEVERAL STORAGE AREAS SHOWN ON THE PLAN.   PLEASE NOTE MATERIALS TO BE STORED IN EACH AREA,   HAZARDOUS MATERIALS AND AMOUNTS, AS WELL AS COMPLIANCE   WITH ANY SPECIAL REQUIREMENTS, IF ANY, FBC413.       18. SHOW ACCESSIBLE EXITS, FBC11-4.1.3(9), A901C.       19. A901C, SEE THE EXIT AT THE BALED STORAGE AREA.   PLEASE SHOW THAT THIS IS NOT A REQUIRED ACCESSIBLE EXIT   DUE TO TRAVEL DISTANCE AS THIS EXIT DOES NOT PROVIDE   VERTICAL ACCESSIBILITY, FBC11-4.1.3(9).       20. THE LIFE SAFETY PLAN DOES NOT CORRELATE WITH A001C.   THERE ARE SEVERAL AREAS IN THE PROCESSING FLOOR WITH   DOORS AND WHAT APPEAR TO BE WALLS OR SOME OTHER   OBSTRUCTION PREVENTING PASSAGE.TRAVEL DISTANCE,   COMMON PATH OF TRAVEL, AND DEAD END CORRIDOR   REQUIREMENTS (FBC1015, FBC1016.3) CANNOT BE DETERMINED   UNLESS THESE OBSTRUCTIONS AS WELL AS THE EQUIPMENT IS   PLACED ON THE LIFE SAFETY PLAN.CONVEYOR BELTS,   CATWALKS, AND OTHER EQUIPMENT WHICH ARE SHOWN ON A001C   BUT WHICH DO NOT AFFECT THE PATH OF TRAVEL NEED NOT BE   SHOWN ON THE LIFE SAFETY PLAN, A901C.       21. S1 DECLARED, BUT CODE ANALYSIS ITEM 5, FIRE   PROTECTION SYSTEM, REFERS TO 903.2.3, REQUIREMENTS FOR   F1 OCCUPANCY.PLEASE REVISE CODE REFERENCE.       22. TO AVOID FIELD ISSUES AND TO ASSIST TRADES AND   INSPECTORS, ON SHEET A901C, PLEASE SHOW HORIZONTAL FIRE   RESISTANCE REQUIRED BETWEEN 1ST FLOOR AND MEZZANINE.       23. PLEASE CLARIFY .15IN FOR EGRESS COMPONENTS, A901C.   IT IS UNCLEAR WHERE THIS COMES FROM.SEE FBC TABLE   1005.1.       24. STAIRWAYS ARE TO BE .3 PER OCCUPANT, NOT .2, FBC   TABLE 1005.1.REVISE A901C.       25. OTHER COMPONENTS IN THE MEANS OF EGRESS ARE TO BE   .2 PER OCCUPANT, NOT .15, REVISE A901C.THE DOORS DO   NOT COMPLY WITH THE MINIMUM REQUIREMENTS WHEN THE   OCCUPANT LOAD IS MULTIPLIED BY .2 RATHER THAN .15; FOR   INSTANCE, SEE STAIR 2 EXIT DOOR, 39.4INCHES REQUIRED   BUT ONLY 32 INCHES PROVIDED.CHECK ALL.       26. DECLARE OCCUPANT LOAD FOR THE SCALE HOUSE,   FBC1004.       27. SHOPS/ENGINEERING FOR THE STEEL CONTAINMENT WALL   PROVIDED BY CP MANUFACTURING A001C REVIEWED BY ENGINEER   AND PRIVATE PROVIDER WILL BE REQUIRED PRIOR TO   INSTALLATION; PROVISO ITEM.       28. A004C, SECTION 2, DOES NOT APPEAR TO SHOW THE DOOR   AND STAIR.       29. A003C AND OTHER SHEETS, PLANS SHOW SEVERAL LADDERS,   STAIRS, EQUIPMENT PLATFORMS, AND CATWALKS.SEE   FBC505.5.1, FBC505.5.2, 505.5.3, FBC CHAPTER 10. PLEASE   PROVIDE SHOPS WHICH SHOW CODE COMPLIANCE OR CONTACT ME   TO DISCUSS AT WHAT POINT DESIGNER/CONTRACTOR PROPOSES   TO SUBMIT THE DRAWINGS FOR THESE COMPONENTS.       30.SHOW LOCATION OF ANY ROOFTOP MECHANICAL EQUIPMENT   INCLUDING DISTANCE FROM EDGE, A006C.SEE FBC1012.5 AND   SHOW ANY REQUIRED GUARDS, LOCATION AND A DETAIL,   FBC1012.       31. THE STRUCTURAL CALCULATIONS (VP BUILDINGS), SCALE   HOUSE SHOP DRAWINGS, AND STRUCTURAL PLAN FOR THE MAIN   BUILDING HAS A PHOTOCOPY OF THE ENGINEER?S SIGNATURE.   AN ORIGINAL WET SIGNATURE IS REQUIRED AS WELL AS A   TITLE BLOCK WITH ALL INFORMATION REQUIRED BY   FAC61G15-23.002.ALSO PLEASE NOTE THE FOLLOWING AND   ADDRESS:       A. THE STRUCTURAL CALCULATIONS AND PLANS FOR THE VP   BUILDING STRUCTURE WERE NOT REVIEWED BY THE PRIVATE   PROVIDER OR BY THE DESIGNER FOR THE BUILDING.       B. THE CALCS AND PLANS STATE NOT FOR CONSTRUCTION;   PLEASE PROVIDE CONSTRUCTION SET.PLEASE ALSO SEE   FAC61G15; PRELIMINARY PLANS SHOULD NOT BE SIGNED AND   SEALED BY THE ENGINEER.       C. PAGE 4 OF THE CALCULATIONS, OTHER SHEETS, PLANS,   REFER TO 2004 FLORIDA STATE BUILDING CODE; PLEASE   REVISE TO GOVERNING CODE WHICH IS FLORIDA BUILDING CODE   2004 WITH 2007 REVISIONS/SUPPLEMENTS.       D. PAGE 4 CALCULATIONS, OTHER SHEETS, AISC89 SHOULD   INCLUDE SUPPLEMENT 1, FBC35.       E. ALL SIGNED AND SEALED SHEETS ARE TO INCLUDE ALL   INFORMATION REQUIRED BY FAC61G15-23.002.IN THE PAST,   THIS ISSUE AS WELL AS THE PHOTOCOPIED SIGNATURE HAS   CAUSED PERMIT DELAYS.PLEASE ONLY SUBMIT PLANS WHICH   COMPLY, ESPECIALLY AS THE ENGINEER HAS BEEN ADVISED OF   THESE REQUIREMENTS ON AT LEAST TWO OTHER PROJECTS IN   THE PAST.THE ENGINEER?S COOPERATION WILL HELP TO   EXPEDITE PLAN REVIEW AND PERMIT ISSUANCE.       32. FLORIDA STATE OR LOCAL PRODUCT APPROVAL OR   MIAMIDADE NOA REQUIRED FOR THE ROOF PANELS, FAC9B72.       33. PRODUCT APPROVALS ARE TO BE APPROVED BY DESIGNER OF   RECORD (SHOP DRAWING REVIEW STAMP OR LETTER),   FBC*106.3.3.AS THEY ARE A PART OF THE BUILDING   ENVELOPE AND REQUIRED TO DETERMINE CODE COMPLIANCE, THE   PRODUCT APPROVALS ARE ALSO TO BE REVIEWED BY THE   PRIVATE PROVIDER.       34. THE PRODUCT APPROVALS SUBMITTED HAVE NOT YET BEEN   REVIEWED AS DESIGN PRESSURES HAVE NOT BEEN SPECIFIED.   HOWEVER PLEASE NOTE THAT THE COIL DOOR PRODUCT APPROVAL   IS FOR A 16FT WIDE DOOR MAXIMUM, BUT A 20FT DOOR IS   SHOWN ON A002C.       35. FOR FL4553, CECO DOOR, PROVIDE THE EVALUATION   REPORT AND INSTALLATION INSTRUCTIONS FROM THE WEBSITE,   WWW.FLORIDABUILDING.ORG.       36. DECLARE WIND DESIGN CRITERIA, FBC1603.1.4.THIS IS   REQUIRED FOR THE STRUCTURE, AND COMPONENT AND CLADDING   PRESSURES REQUIRED BUT NOT PROVIDED.       37. FOR THE PEERLESS HORIZONTAL SLIDER, PROVIDE FLORIDA   STATE PRODUCT APPROVAL OR MIAMIDADE NOA, FAC9B72.A   TEST REPORT WAS PROVIDED BUT ADDITIONAL INFORMATION IS   REQUIRED.       38. THE VACRO PRUDEN BUILDINGS MIAMIDADE NOA SUBMITTED   FOR THE WALL PANELS IS EXPIRED AS OF 7/1/08.PLEASE   PROVIDE A CURRENT PRODUCT APPROVAL, FAC9B72.       39. CALCULATIONS FOR VERSAKING BUILDINGS WERE   SUBMITTED.PLEASE NOTE THE FOLLOWING:       A. THE CALCS ARE TO BE REVIEWED BY THE PRIVATE PROVIDER   AND BY THE DESIGNER OF RECORD.       B. CALCS REFER TO PORTAKING DRAWINGS.PLEASE SUBMIT.   DRAWINGS ARE TO BE REVIEWED BY DESIGNER OF RECORD AND   THE PRIVATE PROVIDER.       C. IT APPEARS THAT THE STRUCTURES WILL BE INSTALLED   INSIDE OF THE VP BUILDING AS NO WIND LOADS WERE   PROVIDED.PLEASE CLARIFY ON THE PLAN; SHOW LOCATION OF   THE PROPOSED PORTAKING STRUCTURES ON THE FLOOR PLAN.       D. INCLUDE THE DOORS FOR THE STRUCTURES ON A DOOR   SCHEDULE OR PROVIDE INFORMATION IN ANOTHER FORMAT TO   SHOW COMPLIANCE WITH ACCESSIBILITY FBC11 AND OTHER   REQUIREMENTS FBC10.       E. CALCULATIONS ARE TO BE EITHER SIGNED, SEALED AND   DATED WITH A TITLE BLOCK ON EACH SHEET, OR AN INDEX   SHEET IN ACCORDANCE WITH FAC61G15-23 USED.PLEASE   ADDRESS.       F. GOVERNING CODE IS TO INCLUDE 2007   REVISIONS/SUPPLEMENTS.       40. THE 3 RING BINDER ENTITLED TECHNICAL SPECIFICATIONS   HAS NOT BEEN REVIEWED BY THE PRIVATE PROVIDER.ALSO IT   WAS NOT PREPARED IN ACCORDANCE WITH FAC61G1-16.002,   003; EITHER EVERY SHEET SIGNED AND SEALED OR AN INDEX   SHEET USED.THIS BINDER MAY BE REMOVED IF ALL   INFORMATION REQUIRED TO SHOW CODE COMPLIANCE IS   INCLUDED IN THE PLANS.OTHERWISE, PLEASE SUBMIT   REVIEWED AND IN COMPLIANCE WITH FAC RULES.PLEASE NOTE   THAT NORMALLY THE ENTIRE DOCUMENT IS NOT REVIEWED; IT   WILL BE INCLUDED WITH THE RECORD SET WITH THE PROVISO   IN ACCORDANCE WITH FBC2004 AND PLAN.       41. THE DOOR SCHEDULE IN THE TECHNICAL SPECIFICATIONS   BINDER DOES NOT INCLUDE ALL OF THE DOORS ON THE DOOR   SCHEDULE IN THE PLAN; FOR INSTANCE, DOORS 102 1, 124 5,   205 2.IF THE TECHNICAL SPECIFICATIONS BINDER REMAINS   A PART OF THE PERMIT SET, PLEASE CORRELATE.       42. THE WALL AT DOOR 132 1 IS NOT SHOWN AS A FIRE   RESISTANCE RATED WALL ALTHOUGH SPECIFIED AS FIRE   RESISTANCE RATED ON THE LIFE SAFETY PLAN A901C.       43. STAIR 1 OPENS INTO THE ELEVATOR LOBBY.SEE   FBC1019.1.1.NO OPENINGS PERMITTED IN THE STAIR   ENCLOSURE OTHER THAN THOSE REQUIRED FOR ACCESS, AND   THOSE OPENINGS ARE TO BE RATED.       43. DOOR 201 1, ASSEMBLY TO STORAGE, DOES NOT SHOW FIRE   RESISTANCE, SEE FBC715.3.       44. SEE FBC TABLE 1016.1, CORRIDORS 203 AND 205 FROM   VISITOR?S GALLERY TO STAIRS TO HAVE 1 HOUR FIRE   RESISTIVE RATING AND THEREFORE DOORS 203 1, 204 1, 205   1, 206 1, 200 1, TO BE RATED IN ACCORDANCE WITH   FBC715.3.       45. A FIRE RATED WALL IS SHOWN BETWEEN TOOL & EQUIPMENT   ROOM AND THE PROCESSING AREA, BUT NO RATING IS SHOWN   FOR DOOR 124 3.PLEASE CLARIFY DESIGN CRITERIA.       46. SEE FBC715.3, DOOR 201 1 AND WINDOWS W5 TO HAVE   FIRE PROTECTION IN ACCORDANCE WITH FBC TABLE 715.3 IF   AN OCCUPANCY SEPARATION IS REQUIRED.PLEASE SEE OTHER   REQUIREMENTS REGARDING FBC302, FBC 5, REGARDING   BUILDING HEIGHT AND AREA.AN UNLIMITED BUILDING SIZE   WAS DECLARED BUT THIS BUILDING DOES NOT COMPLY   (ASSEMBLY LIMITATIONS).DEPENDING ON HOW COMPLIANCE IS   SHOWN, VERTICAL AND HORIZONTAL OCCUPANCY SEPARATION MAY   BE REQUIRED.       47. STAIR 2 SPECIFIES A 1 HOUR WALL ON THE EXTERIOR   SIDE OF THE STAIR, A101C, BUT NO FIRE RATING FOR THE   DOOR 136 1.CLARIFY DESIGN INTENT.       48. A114C, 2 HOUR BLOCK SPECIFIED.PLEASE PROVIDE SPEC   SHEETS AS 2 HOUR IS PROPRIETARY.       49. UL905 SPECIFIED A114C, PROVIDE A COMPLETE DETAIL   FOR THIS AND ANY OTHER UL ASSEMBLIES SPECIFIED ON THE   PLAN.       50. PROVIDE PENETRATION DETAILS, FBC712.       51. SEE STAIR SHAFT DETAILS A114C, DOES THIS GO TO THE   UNDERSIDE OF THE DECK?SEE FBC706.4, 1019.1, PROVIDE A   DETAIL SHOWING COMPLIANCE.       52. A112C SPECIFIES PLYWOOD.PLEASE CLARIFY USE OF   COMBUSTIBLE IN THIS TYPE IIB BUILDING, FBC603.       53. SPECIFY INTERIOR FINISH CLASSIFICATION, FBC TABLE   803.5.       54.THE WALL BETWEEN THE VISITOR?S GALLERY AND THE   OTHER ADJACENT MEZZANINE AREAS DOES NOT SHOW ANY FIRE   RESISTIVE RATING.PLEASE SEE OTHER COMMENTS; IS THIS   ALL ASSEMBLY OCCUPANCY, OR DOES IT REQUIRE AN OCCUPANCY   SEPARATION?DESIGN INTENT IS NOT CLEAR.       55. FBC13-101.1, ENERGY CALCS REQUIRED FOR BOTH THE   MAIN BUILDING AND FOR THE SCALE HOUSE.       56. JANITOR?S ROOM 138 IS TO BE ACCESSIBLE   FBC11-4.1.1(3), WORK AREAS ARE TO BE DESIGNED SO THAT   EMPLOYEES CAN APPROACH, ENTER, AND EXIT THE AREAS. SHOW   TURNING RADIUS.       57. PROVIDE INFORMATION (SPEC SHEETS SUGGESTED) FOR THE   DOOR AT THE VESTIBULE, 112 2 TO SHOW COMPLIANCE WITH   FBC11-4.13 AND FBC10.   58. PROVIDE THE ANTICIPATED OCCUPANT LOAD FOR THE AREA   AT THE BOTTOM OF THE COMMUNICATING NON EGRESS STAIR.   THIS APPEARS TO BE 3FT4IN.10 OCCUPANTS SHOWN FOR DOOR   134 1, PLEASE CLARIFY HOW YOU HAVE DETERMINED   ANTICIPATED OCCUPANTS PER DOOR.       59. SEE FBC1016.4, AIR MOVEMENT IN CORRIDORS.PLEASE   REMOVE SUPPLY, RETURN, EXHAUST, RELIEF OR VENTILATION   AIR DUCTS FROM EXIT ACCESS CORRIDORS, SEE OTHER   COMMENTS.PLEASE NOTE THAT THERE ARE TWO HALLS IN THE   MEZZANINE WHICH SERVE AS CORRIDORS.       60. SEE FBC1019.1.2, PENETRATIONS INTO THE STAIRS ARE   PROHIBITED EXCEPT AS PERMITTED BY THIS CODE SECTION.   PLEASE REVISE PLANS.       61. DETAIL 1 A007C STATES TO SEE STRUCTURAL DRAWINGS   FOR THE STAIR RAIL DETAIL.PLEASE SPECIFY DETAIL,   NUMBER AND PAGE. THERE ARE MANY REFERENCES THROUGHOUT   THE A SHEETS TO SEE STRUCTURAL DWGS.PLEASE REVISE ALL   TO REFER SPECIFICALLY TO A DETAIL.       62. A114C, SPECIFY GUARD PICKET SPACING FBC1012.       63. GUARDRAILS AND HANDRAILS, SPECIFY DESIGN STRENGTH   TO COMPLY WITH FBC1607.7.       64. SEE 3 A007C, THE HANDRAIL IS NOT CONTINUOUS. A106C   HANDRAIL EXTENSIONS AT BOTTOM NOT SHOWN. PLEASE PROVIDE   DETAILS AND CORRELATE A SHEETS.       65. 2 A107 IS LOCATED ON SHEET A102 RATHER THAN 101. IS   ACCESSIBILITY REQUIRED?PLEASE CONFIRM THAT ALL   DETAILS ARE REFERRED TO PROPERLY ON THE PLAN.       66. IT APPEARS THAT THE CHAIN LINK FENCE AND GATE   OBSTRUCT THE MEANS OF EGRESS CONTINUITY, FBC1003.1. THE   GATE AND COIL DOOR DO NOT MEET ANY OF THE REQUIREMENTS   AS A MEANS OF EGRESS COMPONENT OF CHAPTER 10.       67. PROVIDE A SITE PLAN AND A SURVEY TO BE INCORPORATED   INTO THIS PLAN TO SHOW COMPLIANCE WITH THE OPEN SPACE   REQUIREMENT FBC507.2, REVIEWED BY PRIVATE PROVIDER, AS   WELL AS ACCESSIBILITY REQUIREMENTS FOR PARKING AND   ACCESSIBLE ROUTE, SEE OTHER COMMENTS.PLANS WERE   SUBMITTED WHICH WERE PREPARED BY THE LANDSCAPE   ARCHITECT; IT IS NOT CLEAR IF THE LANDSCAPE PLAN IS TO   BE USED TO SHOW CODE COMPLIANCE WITH LIFE SAFETY, FBC   CHAPTER 5, AND ACCESSIBILITY.PLEASE PROVIDE A PLAN TO   BE USED FOR THAT PURPOSE OR INCORPORATE THE REQUIRED   INFORMATION INTO THE C SHEETS.       68. THE SITE PLAN IS TO DECLARE TOTAL NUMBER OF PARKING   SPACES AND TOTAL NUMBER OF ACCESSIBLE PARKING SPACES   FBC11-4.1.2(5)(A).       69. THE ACCESSIBLE PARKING SPACES ARE TO BE DISPERSED   FBC11-4.6.2.PLEASE SHOW THE DOORS ON THE SITE PLAN IN   RELATION TO THE PROPOSED ACCESSIBLE PARKING SPACES AND   ALSO SHOW ACCESSIBLE ENTRANCES.       70. SHOW THE ACCESSIBLE ROUTE FROM THE PUBLIC WAY TO   THE ACCESSIBLE BUILDING ENTRANCE FBC11-4.3.2.1(1).       71. PROVIDE A DETAIL FOR THE ACCESSIBLE PARKING SPACE   FBC11-4.6 AND SHOW WIDTH OF ACCESSIBLE ROUTE, NO LESS   THAN 44INCHES, FBC11-4.6.2(1).       72. PLEASE NOTE THAT THE FOUNDATION PERMIT HAS NOT BEEN   ISSUED; THEREFORE, ANY INFORMATION INCLUDED IN THAT   PERMIT CANNOT BE USED TO SHOW CODE COMPLIANCE FOR THIS   PERMIT AT THIS TIME.       73. SHOW LOCATION OF STROBES, FBC11-4.28.1.       74. ELEVATOR SIGNAGE TO COMPLY WITH FBC11-4.10.5, CALL   BUTTONS WITH FBC11-4.10.3.       75. SEE FC1009.4, STAIR LANDINGS, INTERMEDIATE LANDING   IS 44 IN, 48 INCHES REQUIRED, A113C.       76. PROVIDE A SPECIFICATION FOR ATTACHMENT OF THE GRAB   BARS TO THE SHEET METAL TO SHOW COMPLIANCE WITH   FBC1607.7.1.1, FBC11-4.26.3.       77. PROVIDE A SPECIFICATION FOR ATTACHMENT OF THE   BACKING FOR THE GRAB BARS (A111C) TO SHOW COMPLIANCE   WITH FBC1607.7.1.1, FBC11-4.26.3.DETAIL STATES   SCREWED TO STUD BUT DOES NOT SPECIFY SIZE OF SCREWS OR   DISTANCE APART, DOES NOT SPECIFY A WIDTH FOR THE 22G   SHEET METAL BACKING.       78. SEE FBC1006 AND SHOW COMPLIANCE.IT IS NOT CLEAR   WHAT ILLUMINATION WILL BE PROVIDED FOR THE EQUIPMENT   PLATFORMS, STAIRS.       79. INFORMATIONAL ONLY; SEPARATE PERMITS REQUIRED FOR   SIGNS.THEY ARE USUALLY APPLIED FOR BY THE SIGN   CONTRACTOR PRIOR TO INSTALLATION.       80. PLEASE SHOW COMPLIANCE WITH FBC910, SMOKE AND HEAT   VENTS.PROVIDE CALCULATIONS ON THE PLAN AND SHOW   COMPLIANCE WITH ALL REQUIREMENTS.       81. FBC505.5.2, FP101C DOES NOT MAKE REFERENCE TO   SPRINKLERS ABOVE AND BELOW PLATFORMS.ON THE SPRINKLER   HEAD LAYOUT PLAN, SHOW COMPLIANCE.       82. SEE OTHER COMMENTS.IT IS NOT CLEAR WHETHER THE   EXIT LIGHTS PROVIDED ARE ADEQUATE, FBC1006.3; CANNOT   DETERMINE WHETHER OR NOT EQUIPMENT OBSTRUCTS THE EXIT   LIGHTS.PLEASE ADDRESS ON THE PLAN, PREFERABLY THE   LIFE SAFETY PLAN.       83. SEE FBC1503.6, PROVIDE A DETAIL FOR CONDENSATE   LINES AND ROOF DOWNSPOUTS.       84. WHEN RESUBMITTING, PLEASE INCLUDE A DETAILED   RESPONSE LETTER STATING HOW EACH ITEM WAS ADDRESSED,   INCLUDING PAGE NUMBER(S) IF POSSIBLE.THIS WILL HELP   TO EXPEDITE PLAN REVIEW.       85. SOME OF THE PLANS HAVE BEEN RETAINED.WHEN   RESUBMITTING, PLEASE SUBMIT THREE COMPLETE SETS. THE   PLANS WHICH HAVE BEEN RETAINED WILL NOT BE RELEASED FOR   PERMITTING PURPOSES.CONTACT DEWEY PALMER IF YOU HAVE   QUESTIONS REGARDING THIS ISSUE. Review Stop E ELECTRICAL Rev No 16 Status P Date 2009-09-24 Cont ID   Sent By dpalmer Date 2009-09-24 Time 16:04 Rev Time 0.00 Received By dpalmer Date 2009-09-24 Time 16:04 Sent To PC Notes 2009-09-24 16:05:13 REVISED PANELS. Review Stop E ELECTRICAL Rev No 15 Status P Date 2009-08-31 Cont ID   Sent By dpalmer Date 2009-08-31 Time 12:10 Rev Time 0.00 Received By dpalmer Date 2009-08-31 Time 12:10 Sent To PC Notes 2009-08-31 12:10:48         ** REDLINED REVIEW **               1) NOTE: LARGEST BRANCH CIRCUIT ON SCS IS SHOWN AS   30AMP. AS ELP1 HAS NOW BEEN REVISED TO REMOVE FEED TO   SUB PANEL, THEN THE ACTUAL LARGEST BREAKER IS 2-P   20AMP.       2) NOTE: E-117 NEEDS TO BE REVISED FOR ELP1           IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 14 Status F Date 2009-07-16 Cont ID   Sent By dpalmer Date 2009-07-16 Time 09:55 Rev Time 0.00 Received By dpalmer Date 2009-07-16 Time 09:55 Sent To   Notes 2009-07-16 09:56:02         ** DENIED **       SUBMISSION OF THE SELECTIVE COORDINATION STUDY.       ** THE FOLLOWING COMMENTS ARE BASED ON THE SELECTIVE   COORDINATION STUDY AND NEW COMMENTS DERIVED DURING   REVIEW. A CALL WAS MADE TO GIPE AND ASSOCIATES AND   SPOKE TO MICHAEL PURTELL.       ** IN THE NOTES BELOW THE SELECTIVE COORDINATION STUDY   WILL BE NOTED AS SCS.       1) NOTE: NEW COMMENT: PLEASE SEE 700.9(B). PLEASE SEE   NEC 2005 HANDBOOK COMMENTARY FOR WIRING OF SYSTEMS.   PLEASE EXPLAIN HOW OPTIONAL STAND-BY LOADS SUCH AS   CEILING FANS, SCALES AND OTHER GENERAL LOADS MAY BE   PART OF THE LIFE SAFETY/ EMERGENCY SYSTEM. THIS WAS ON   PREVIOUS PLANS HOWEVER WAS MISSED BY REVIEWER.   STAND-BY LOADS MAY BE FED FROM SEPARATE FEED ON   GENERATOR WITH SEPARATE TRANSFER SWITCH OR REMOVE ALL   LOADS FROM EMERGENCY PANELS.   IF ELP-1 WAS A * SWITCHBOARD * THEN THERE COULD BE A   SEPARATE BRANCH FEED TO A STAND-BY ATS WHICH WOULD THEN   FEED TERP-1.       2) NOTE: PLEASE COORDINATE THE SCS WITH THE PLANS.   PLEASE SEE THE SCS RISER AS THIS INDICATES ONLY ONE SET   OF FEEDERS TO ATS-2 WHERE THE PLANS ON RECORD INDICATES   2 SETS OF PARALLEL 3/0.       3) NOTE: PLEASE EXPLAIN THE SCS RISER WHICH SEEMS TO   INDICATE 100HP AND 50HP FOR FIRE PUMP.       4) NOTE: PLEASE COORDINATE THE BREAKER ON THE GENERATOR   FOR ATS-2E WHICH SHOWS 250A ON SCS RISER AND 200AMP ON   PLANS.       5) NOTE: ALL OCP DEVICES ON THE GENERATOR SHALL BE PART   OF THE STUDY. PLEASE KNOW BASED ON THE 60AMP BREAKER ON   ELP-1 THIS WOULD ALSO BE ON STUDY. ALTHOUGH PLEASE SEE   COMMENT #1 ABOVE AS THIS DOES AFFECT THE RISER AS IT   STANDS.           240.12, 701.18, 700.27                   ** IMPORTANT **   ONCE AUDIT/REVIEWS ARE COMPLETE AND PLANS ARE PICKED UP   FOR CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE   ALL OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING.   DO NOT LEAVE ANY OLD/VOIDED SHEETS IN SETS.   PLEASE DO NOT ATTACH SUPPORTING DOCUMENTS TO PLANS. ANY   ADDITIONAL DOCUMENTATION SUCH AS PRODUCT APPROVALS,   SPEC/CUT SHEETS, CALCULATIONS ETC. SHOULD BE PLACED   INTO TWO SETS/FOLDERS/BINDERS ETC.   PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS   SHOULD BE SUBMITTED FOR REFERENCE.   THIS WILL HELP IN THE AUDIT/REVIEW PROCESS AND AVOID   ANY DELAYS.       IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 13 Status P Date 2009-05-18 Cont ID   Sent By dpalmer Date 2009-05-18 Time 14:51 Rev Time 0.00 Received By dpalmer Date 2009-05-18 Time 14:51 Sent To   Notes 2009-05-18 14:52:01 REVS FOR BALER Review Stop E ELECTRICAL Rev No 12 Status P Date 2009-04-20 Cont ID   Sent By dpalmer Date 2009-04-20 Time 14:28 Rev Time 0.00 Received By dpalmer Date 2009-04-20 Time 14:28 Sent To PC Notes 2009-04-20 14:28:35 ELEC REV E 107 CR5, 120 CR3 Review Stop E ELECTRICAL Rev No 11 Status F Date 2009-04-12 Cont ID   Sent By dpalmer Date 2009-04-12 Time 11:03 Rev Time 0.00 Received By dpalmer Date 2009-04-12 Time 11:03 Sent To PC Notes 2009-04-12 11:03:50 ** DENIED**       1) NOTE: THE PLANS SUBMITTED DO NOT CONTAIN THE SAME   SIGNATURE AS ALL OTHER PLANS IN FILE FOR THE SAME   ENGINEER OF RECORD. THE PLANS ARE SIGNED WITH A   SIGNATURE WHICH IS COMPLETELY DIFFERENT. PLEASE SEE FS   471.023 AND FAC 61G15-23.002.   PLANS SHALL BE SIGNED AND SEALED BY THE ENGINEER BY OF   RECORD. AN ENGINEER MAY NOT DESIGNATE ANOTHER PERSON TO   SIGN PLANS. THIS HAS BEEN CONFIRMED ON MANY OCCASIONS   WITH THE ATTORNEYS AND INVESTIGATORS FOR THE FLORIDA   BOARD OF PROFESSIONAL ENGINEERS. PLEASE CONTACT THE   BOARD, JERRY ONGLEY, OR JACK BEAMISH WITH ANY QUESTIONS   ON THIS MATTER.   ** THIS REVIEWER HAD PLACE PHONE CALL TO THE ENGINEER'S   OFFICE ON THE 3RD OF APRIL IN WHICH THE OFFICE SAID THE   ENGINEER WAS OUT ON A VACATION. THIS IS THE SAME DATE   ON PLANS WHEN SIGNED AND SEALED.   ** ONE SET OF PLANS ARE BEING RETAINED BY THIS OFFICE.           IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 10 Status P Date 2009-04-02 Cont ID   Sent By dpalmer Date 2009-04-02 Time 19:26 Rev Time 0.00 Received By dpalmer Date 2009-04-02 Time 19:26 Sent To   Notes 2009-04-02 19:26:59 REV 104, 105 AND 108 Review Stop E ELECTRICAL Rev No 9 Status F Date 2009-04-01 Cont ID   Sent By dpalmer Date 2009-04-01 Time 17:49 Rev Time 0.00 Received By dpalmer Date 2009-04-01 Time 17:49 Sent To PC Notes 2009-04-01 17:50:04 ** DENIED REVIEW **       1) NOTE: SHEETS E107, 120 AND 121 SHALL COORDINATE WITH   THE ELECTRICAL PLANS FOR THE EQUIPMENT ELECTRICAL   ENGINEERED PLANS.   PLEASE SEE THE PANEL PP-EC IS STILL NOT LISTED ON THE   MSB SWITCHBOARD.   THE RISER SUBMITTED FOR THE EQUIPMENT ENGINEERED PLANS   ALONG THE REVISED RISER ON E120 SHOWS A 175AMP BREAKER   FEEDING PANEL PP-EC HOWEVER PLEASE TAKE A LOOK AT MSB   SCHEDULE. THE ONLY 175 BREAKER ON EITHER E107 OR E120   IS THE 175AMP BREAKER WHICH IS STATED FOR THE   *RELOCATED BALER*. TO DATE THERE IS NO PP-EC LISTED ON   EITHER MSB SCHEDULE.   PLEASE COORDINATE ALL.   PLEASE REVISE LOAD CALCULATIONS.   408.4, 310.16, 240, 220 ETC       2) NOTE: SHEET E-1 THROUGH E-4 HAS BEEN STAMPED FOR   ELECTRICAL ENGINEERED EQUIPMENT PLANS. THIS SCOPE OF   WORK IS NOT PART OF THE BASE BUILDING ELECTRICAL. IN   FACT THIS SCOPE OF WORK IS DONE BY A SEPARATE   ELECTRICAL CONTRACTOR.       A PHONE CALL WAS PLACED TO THE BASE BUILDING ELECTRICAL   ENGINEER FOR A RETURN CALL.   ONE SET OF ELECTRICAL PLANS FOR BASE BUILDING HAVE BEEN   RETAINED BY THIS REVIEWER.               IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 8 Status N Date 2009-03-27 Cont ID   Sent By dpalmer Date 2009-03-27 Time 14:35 Rev Time 0.00 Received By dpalmer Date 2009-03-27 Time 14:35 Sent To   Notes 2009-03-27 14:36:28 HORN/ STOBE RFI, PER BUIDLING AND FIRE REVIEW. Review Stop E ELECTRICAL Rev No 7 Status F Date 2009-03-26 Cont ID   Sent By dpalmer Date 2009-03-26 Time 18:15 Rev Time 0.00 Received By dpalmer Date 2009-03-26 Time 18:15 Sent To PC Notes 2009-03-26 18:15:14 ** DENIED REVIEW **       ** PLEASE SEE NOTES FROM PREVIOUS REVIEW.       1) NOTE: PLEAS SUBMIT A COMPLETE COORDINATION STUDY.   THIS NEEDS TO INCLUDE COORDINATION RISER, STUDY AND   TIME CURVES. THE SUBMITTED SHORT CIRCUIT ANALYSIS IS   NOT ALL THE INFORMATION THAT IS NEEDED TO VERIFY   MINIMUM CODE COMPLIANCE. IT WAS GONE OVER ON THE PHONE   THAT THE COMPLETE STUDY ALONG WITH TIME CURVES.   700.27, 701.8, 240.12 ETC.   *** IT IS IMPORTANT TO KNOW THAT SINCE THE COORDINATION   STUDY HAS YET TO BE SUBMITTED THERE MAY BE NEW COMMENTS   ON THE NEXT REVIEW WHICH CAN NOT BE MADE AT THIS TIME.       2) NOTE: AS STATED ON PREVIOUS REVIEW. THE ENGINEER FOR   THE BASE BUILDING ELECTRICAL PLANS NEEDS TO SIGN THE   SHOP DRAWING REVIEW STAMPED OF THE SUBMITTED ELECTRICAL   ENGINEERED SYSTEMS PLANS.   THE PERSON SIGNED IS NOT THE ENGINEER OF RECORD. ALL   ELECTRICAL WORK, LOADS ETC IN THE BUILDING BEFORE THE   CERTIFICATE OF OCCUPANCY IS ISSUED IS UNDER THE REVIEW   AND RESPONSIBILITY OF THE BASE BUILDING DESIGN   PROFESSIONAL TO BE AWARE OF TRACK AND ADJUST MAIN   PLANS.   FS 471.025       3) NOTE: PLEASE SEE BASE BUILDING RISER AND SUBMITTED   ELECTRICAL ENGINEERING PLANS ARE STILL NEED   COORDINATION. PLEASE SEE E120CR1 WHICH IS NOW NOT   REVISED TO MATCH THE UPDATED MSB ON E107CR4.   FOR EXAMPLE: REVISED MCC1 ON E107   FOR EXAMPLE: REVISED PP-EC ON E120 WHICH IS NOT ON E   107.   PLEASE PROVIDE LOADS/CIRCUITS FOR THE LC. (LOAD   CENTERS) LC210- LC217   215.5, 408.4, 230, 240 SECTIONS GIVEN FOR COORDINATION   OF ELECTRICAL PLANS.   THE TOTAL LOAD SHOWN ON MSB IS NOT ACCURATE. PLEASE   UPDATE WITH ALL NEW LOADS.       4) NOTE: FOR CONTRACTOR INFORMATION: IF THE EQUIPMENT   PLANS AND BASE BUILDING PLANS ARE CLEARED UP BASED ON   NOTES #2 AND #3 THE EQUIPMENT CONTRACTOR WILL BE ABLE   TO APPLY FOR PERMIT. COMMENT #1 MAY REMAIN OUTSTANDING.       IF THERE ARE ANY QUESTIONS, PLEASE CALL.                   DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 6 Status F Date 2009-03-10 Cont ID   Sent By dpalmer Date 2009-03-10 Time 19:15 Rev Time 0.00 Received By dpalmer Date 2009-03-10 Time 19:15 Sent To PC Notes 2009-03-10 19:15:57 ** DENIED REVISIONS **       REVISION OF PLANS FOR BASE BUILDING AND SUBMITTAL OF   ELECTRICAL MANUFACTURING EQUIPMENT PLANS.       1) NOTE: THE REVISED SHEETS FOR ARCHITECTURAL NOTES AND   SHEET E104CR4 ARE OK.       2) NOTE: ELECTRICAL RISER SHEET E107CR3 WILL REMAIN IN   FAILED STATUS UNTIL COORDINATION WITH MANUFACTURING   PLANS AND REVISIONS ARE MADE.   SEE NOTE #4 BELOW AND OTHER NOTES.       ** REVIEW FOR PLANS BY ASSOCIATED ENGINEERING   INCORPORATED:       3) NOTE: THE TITLE BLOCKS NEED TO CONTAIN THE PRINTED   NAME AND LICENSE NUMBER OF THE PROFESSIONAL ENGINEER   EVEN IF THIS INFORMATION IS IN THE SAID SEAL OF THE   SAME DESIGN PROFESSIONAL.   FLORIDA ADMINISTRATIVE CODE 61G15-23.002       4) NOTE: PLANS SHOWS GFI PROTECTION FOR THE 3000AMP   MAIN DISTRIBUTION CENTER. PLEASE SEE 240.13,230.95 AS   THIS SHOULD BE NOTED OR IDENTIFIED AS GFP. (GROUND   FAULT PROTECTION) GFI IS FOR PERSONNEL PROTECTION.   THE RISER NOTES # 7 ON E107CR3 STILL NOTES GFI EVEN AS   THE MSB PANEL STATES GFP.   PLEASE COORDINATE.       5) NOTE: PLEASE SEE MCC1 AS THIS EQUIPMENT IS SHOWN   RATED AT 450AMP YET THERE IS A 500AMP BREAKER ON E107   SHOWN FEEDING THIS EQUIPMENT. THIS IS THE SAME ON THE   EQUIPMENT PLANS.   240, 230, 310, 110.14 ETC.       6) NOTE: PLEASE SEE THE EQUIPMENT PLANS AS THEY CLEARLY   INDICATE A 600AMP DISTRIBUTION SECTION WHICH IS NOT ON   THE E107 SHEET/ RISER.   NO INFORMATION IS PROVIDED FOR THIS PROVISION ON THE   BASE BUILDING PLANS.   FBC 106.1.1, 106.1.2, 106.3.5.1.2, COORDINATION AND   ADDITIONAL INFORMATION ON RECORD PLANS. NEC 220,215.5,   240.4,230 ETC. THESE SECTIONS ARE GIVEN AS GENERAL   CHAPTERS AS PLANS ARE NOT COORDINATED. IT IS NOT   POSSIBLE TO DO A SPECIFIC REVIEW.       7) NOTE: PLEASE SEE THE ELECTRICAL EQUIPMENT RISER   INDICATES A NEW 300AMP BREAKER ON THE MSB FEEDING A NEW   225KVA TRANSFORMER. NEITHER OF THESE TWO ITEMS IS ON   THE BASE BUILDING ELECTRICAL RISER DIAGRAM ON SHEET   E107.   NO INFORMATION IS PROVIDED FOR THIS PROVISION ON THE   BASE BUILDING PLANS.   FBC 106.1.1, 106.1.2, 106.3.5.1.2, COORDINATION AND   ADDITIONAL INFORMATION ON RECORD PLANS. NEC 220,215.5,   240.4,230, 408.4ETC. THESE SECTIONS ARE GIVEN AS   GENERAL CHAPTERS AS PLANS ARE NOT COORDINATED. IT IS   NOT POSSIBLE TO DO A SPECIFIC REVIEW.       8) NOTE: PLEASE SEE THE ELECTRICAL EQUIPMENT RISER AS   THIS RISER CONTAINS TEN ELECTRICAL PANELS WHICH ARE   IDENTIFIED AS SE1 THROUGH SE 10. NONE OF THESE PANELS   ARE ON THE BASE BUILDING ELECTRICAL PLANS ON E107.   PLEASE SEE NOTES # 6 AND 7 ABOVE AS THESE ARE DIRECTLY   AFFECTED BY THESE ITEMS.   NO INFORMATION IS PROVIDED FOR THIS PROVISION ON THE   BASE BUILDING PLANS.   FBC 106.1.1, 106.1.2, 106.3.5.1.2, COORDINATION AND   ADDITIONAL INFORMATION ON RECORD PLANS. NEC 220,215.5,   240.4,230, 408.4ETC. THESE SECTIONS ARE GIVEN AS   GENERAL CHAPTERS AS PLANS ARE NOT COORDINATED. IT IS   NOT POSSIBLE TO DO A SPECIFIC REVIEW.       9) NOTE: THE BASE BUILDING ELECTRICAL RISER INDICATES A   MCCB YET THE EQUIPMENT RISER FROM MANUFACTURE DOES NOT   INDICATE THIS MCCB. THIS IS NOT ON THE RISER OR IN THE   LOAD CALCULATIONS.   215.5,220,408.4,240.4, 310.16 ETC   NO INFORMATION IS PROVIDED FOR THIS PROVISION ON THE   BASE BUILDING PLANS.   FBC 106.1.1, 106.1.2, 106.3.5.1.2, COORDINATION AND   ADDITIONAL INFORMATION ON RECORD PLANS. SECTIONS ARE   GIVEN AS GENERAL CHAPTERS AS PLANS ARE NOT COORDINATED.   IT IS NOT POSSIBLE TO DO A SPECIFIC REVIEW.       10) NOTE: PLEASE KEEP IN MIND A COMPLETE REVISED   ELECTRICAL COORDINATION STUDY ALONG WITH TIME CURVES   ETC WILL BE REQUIRED NOT THAT ALL ELECTRICAL EQUIPMENT   IS NOTED, FIGURED ETC.   PLEASE SEE 240.12, 700.27, 701.8.   FBC 106.1.1, 106.1.2 FOR CLARITY, COORDINATION AND   INFORMATION ON THE RECORD PLANS.           IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 5 Status F Date 2009-02-23 Cont ID   Sent By dpalmer Date 2009-02-23 Time 18:23 Rev Time 0.00 Received By dpalmer Date 2009-02-23 Time 18:23 Sent To   Notes 2009-02-23 18:24:35 ** DENIED/ PASSED REVISIONS **               1) NOTE: PLEASE SEE PROVISO ISSUED 12/17/08. ITEMS   NUMBERS 2, 4 AND 5 NEED TO BE REVISED AT THIS TIME.   THESE ARE NOT ITEMS FOR *AS BUILTS*.   FOR INFORMATION.   AS-BUILTS ARE PLANS MADE UP OF ALL REVISED PLANS ALONG   THE PROGRESS OF THE PROJECT. THE CITY OF WEST PALM   BEACH DOES REQUIRE REVISIONS HOWEVER NOT A FINAL SET OF   AS-BUILDS.       2) NOTE: THE POWER PLAN SHEET WAS OK, STAMPED.       3) NOTE: COMMENTS FROM PROVISO WITH RESPECT TO   CERTIFICATE OF AUTHORIZATION NUMBERS ON REQUIRED   PREVIOUS PLANS IS STILL IN EFFECT. THIS WILL BE   ADDRESSED WHEN SUBMITTING PLANS WHICH WERE NOT REVIEWED   AND STAMPED. THIS IS FOR EQUIPMENT MANUFACTURE PLANS   AND MANUFACTURES ELECTRICAL PLANS.   FS 471.023,FAC 61G15-23.002. REVIEW OF SAID DOCUMENTS   STILL NEEDS TO TAKE PLACE FOR CODE COMPLIANCE.   110.3,90.7 ETC       ** THIS REVIEW WILL REMAINED IN A FAILED STATUS EVEN AS   POWER PLAN SHEET E105 IS OK.                   IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]             Review Stop E ELECTRICAL Rev No 4 Status P Date 2008-12-17 Cont ID   Sent By dpalmer Date 2008-12-17 Time 11:44 Rev Time 0.00 Received By dpalmer Date 2008-12-17 Time 11:44 Sent To   Notes 2008-12-17 11:48:35 ** PROVISO/REDLINED PLANS***       THE FOLLOWING ITEMS SHALL BE ADDRESSED AND SUBMITTED.       1) NOTE: ELECTRICAL MANUFACTURER'S SHOP DRAWINGS WILL   BE SUBMITTED AT LATER DATE ONCE CA # FROM STATE IS   OBTAINED.   FS471.023,FAC 61G15-23.002           2) NOTE: THE RISER STILL INDICATES * EQUIPMENT   GROUNDING CONDUCTORS* BEFORE THE FIRST MEANS OF   DISCONNECT FROM THE FPL TRANSFORMER WHICH IS NOT   PERMITTED. THIS HAS BEEN NOTED IN ALL OF THE THREE   PREVIOUS REVIEWS YET THE RISER NOTES HAVE NOT BEEN   CORRECTED. THE RESPONSE LETTER MENTIONS REVISIONS WERE   MADE HOWEVER THIS IS NOT THE CASE.       3) NOTE: PLEASE SEE THE SUBMITTED ELECTRICAL PLANS FOR   EQUIPMENT FROM ASSOCIATED ENGINEERS STILL DOES NOT HAVE   ALL INFORMATION ON TITLE BLOCKS COMPLETE. IN FACT THE   TITLE BLOCK WHERE THE REQUIRED CERTIFICATE OF   AUTHORIZATION NUMBER IS SUPPOSE TO BE STATES THE CA   NUMBER IS PENDING. THESE MAY NOT BE PART OF THE   SUBMITTED DOCUMENTS WITHOUT COMPLETE INFORMATION. THE   TITLE BLOCKS ARE REQUIRED TO CONTAIN THE PRINTED NAME   AND LICENSE NUMBER OF DESIGNER ALONG WITH THE   CERTIFICATE OF AUTHORIZATION NUMBER.\   FAC 61G15-23.002, FS 471.023           4) NOTE: THE STAIRS FROM THE MEZZANINE LEVEL STILL DO   NOT INDICATE ANY LIGHTING MEETING EGRESS REQUIREMENTS.   THE RESPONSE AND PER PHONE CONVERSATION PREVIOUSLY   MENTIONED THIS WAS AND IS NOT AN EGRESS PATH REQUIRED   OR OTHER WISE. THIS IS A MEANS OF ESCAPE AS DEFINE IN   THE LIFE SAFETY CODE.   IN ORDER NOT TO BE PART OF ANY EGRESS PATH SIGNAGE FOR   DOOR MUST BE ON LIFE SAFETY PLANS AS WELL AS ELECTRICAL   PLANS. PLEASE SEE NFPA-101   7.10.8.3.1 ANY DOOR, PASSAGE, OR STAIRWAY THAT IS   NEITHER AN EXIT NOR A WAY OF EXIT ACCESS AND THAT IS   LOCATED OR ARRANGED SO THAT IT IS LIKELY TO BE MISTAKEN   FOR AN EXIT SHALL BE IDENTIFIED BY A SIGN THAT READS AS   FOLLOWS:   NO   EXIT   7.10.8.3.2 THE NO EXIT SIGN SHALL HAVE THE WORD NO IN   LETTERS 51 MM (2 IN.) HIGH, WITH A STROKE WIDTH OF 9.5   MM ( IN.), AND THE WORD EXIT IN LETTERS 25 MM (1 IN.)   HIGH, WITH THE WORD EXIT BELOW THE WORD NO, UNLESS SUCH   SIGN IS AN APPROVED EXISTING SIGN.       ** THIS IS REQUIRED WHETHER OR NOT COMMENT IS MADE BY   ANY OTHER TRADE.           5) NOTE: PLEASE CLARIFY JOCKEY PUMP WHICH RISER   INDICATES 30AMP DISCONNECT FUSED AT 30AMPS YET BRANCH   FROM ELP1 ONLY HAS 20AMP OCP WITH #12 CONDUCTORS.??   240.4,310.16, 430.   FBC 106.1.1 FOR CLARITY AND COORDINATION.   *** PRO       *** NOTED SEPARATE PERMITS FOR LIGHTNING PROTECTION,   LOW VOLTAGE SYSTEMS, FIRE ALARM, FIRE SPRINKLER. THE   BASE PLANS MAY BE REFERENCED FOR LOW VOLTAGE SYSTEM   ONLY. SEPARATE PLANS WILL BE REQUIRED FOR LP, FS AND   FA.   THIS IS NOTED FOR REVIEW ONLY. NO RESPONSE OR CHANGES   ARE NEEDED ON PLANS OR SUBMITTED DOCUMENTS.           *** LETTER IN FILE WITH RESPECT TO BUILDING OCCUPANCY   WHEN UNDER EMERGENCY BACK UP POWER. IN COMPLIANCE WITH   FBC CHAPTER 10 AS WELL AS NFPA-101 THE BUILDING SHALL   BE EVACUATED WHEN NORMAL POWER IS LOST INCLUDING ALL   EMPLOYEEST. LETTER SUBMITTED SIGNED AND NOTARIZED FROM   MR. PATRICK CARROLL DIRECTOR OF FACILITIES DEVELOPMENT   IS IN FILE.         Review Stop E ELECTRICAL Rev No 3 Status F Date 2008-12-17 Cont ID   Sent By dpalmer Date 2008-12-15 Time 11:43 Rev Time 0.00 Received By dpalmer Date 2008-12-12 Time 17:10 Sent To   Notes 2008-12-17 11:44:30 ** DENIED 3RD REVIEW **       ** SOME ITEMS FROM PREVIOUS REVIEW ARE STILL IN NEED OF   ADDRESSING.   ** SOME OF THE ITEMS MAY BE ABLE TO BE SET UP AS PART   OF A PROVISO/ISSUANCE WITH CONDITIONS HOWEVER SOME MUST   BE ADDRESSED AT THIS TIME.       1) NOTE: PLEASE SEE THE SUBMITTED ENERGY CALCULATIONS   NEED TO BE SIGNED, DATED AND SEALED BY THE RESPONSIBLE   DESIGNER. THE CERTIFICATION SHEET CONTAINS A SIGNATURE   AND DATE HOWEVER NOT SEALED WITH THE RAISED SEAL. THIS   IS FOR BOTH THE MAIN FACILITY BUILDING AS WELL AND   SCALE HOUSE.       2) NOTE: PLEASE SEE THE CALCULATIONS FOR ELECTRICAL   LIGHTING APPEAR TO SHOW NO GROSS ERRORS AS NOTED IN FBC   13-103.3. HOWEVER PLEASE SEE THE SCALE HOUSE   CALCULATIONS AS THESE MOST CERTAINLY COULD NOT BE   SIGNED AS COMPLIANT BY ELECTRICAL WHEN THERE ARE ITEMS   FOR OTHER TRADES LEFT COMPLETELY BLANK.   SOME OF THESE EXAMPLES WOULD BE THE IDR INDICATES:   NO WINDOWS YET THERE ARE WINDOWS ON THE BUILDING AND   FENESTRATIONS ARE ALSO BLANK.   NO DOORS, YET THERE ARE DOORS ON PLANS.   FLOORS FOR ALL AREAS NOTED AS CARPET AND RUBBER   PADDING. THIS IS NOT POSSIBLE. THERE ARE AREAS WITH   TILE AND OTHER SURFACES WHICH ARE NOT CARPET AND RUBBER   PADDING.       ** THESE ITEMS ARE CLEAR TO THIS REVIEWER AS GROSS   ERRORS AND THESE CALCULATIONS COULD NOT BE STAMPED BY   ELECTRICAL AS CODE COMPLIANT WHETHER OR NOT THEY WERE   SIGNED AND SEALED.   ** THESE ITEMS NEED TO BE ADDRESSED WHETHER OR NOT   COMMENT IS MADE BY OTHER REVIEW STAFF.       13-400.A.3, 13-401, 13-403, 13-405       3) NOTE: THE RISER STILL INDICATES * EQUIPMENT   GROUNDING CONDUCTORS* BEFORE THE FIRST MEANS OF   DISCONNECT FROM THE FPL TRANSFORMER WHICH IS NOT   PERMITTED. THIS HAS BEEN NOTED IN ALL OF THE THREE   PREVIOUS REVIEWS YET THE RISER NOTES HAVE NOT BEEN   CORRECTED. THE RESPONSE LETTER MENTIONS REVISIONS WERE   MADE HOWEVER THIS IS NOT THE CASE.       4) NOTE: PLEASE SEE THE SUBMITTED ELECTRICAL PLANS FOR   EQUIPMENT FROM ASSOCIATED ENGINEERS STILL DOES NOT HAVE   ALL INFORMATION ON TITLE BLOCKS COMPLETE. IN FACT THE   TITLE BLOCK WHERE THE REQUIRED CERTIFICATE OF   AUTHORIZATION NUMBER IS SUPPOSE TO BE STATES THE CA   NUMBER IS PENDING. THESE MAY NOT BE PART OF THE   SUBMITTED DOCUMENTS WITHOUT COMPLETE INFORMATION. THE   TITLE BLOCKS ARE REQUIRED TO CONTAIN THE PRINTED NAME   AND LICENSE NUMBER OF DESIGNER ALONG WITH THE   CERTIFICATE OF AUTHORIZATION NUMBER.\   FAC 61G15-23.002, FS 471.023   ***PRO       5) NOTE: THE STAIRS FROM THE MEZZANINE LEVEL STILL DO   NOT INDICATE ANY LIGHTING MEETING EGRESS REQUIREMENTS.   THE RESPONSE AND PER PHONE CONVERSATION PREVIOUSLY   MENTIONED THIS WAS AND IS NOT AN EGRESS PATH REQUIRED   OR OTHER WISE. THIS IS A MEANS OF ESCAPE AS DEFINE IN   THE LIFE SAFETY CODE.   IN ORDER NOT TO BE PART OF ANY EGRESS PATH SIGNAGE FOR   DOOR MUST BE ON LIFE SAFETY PLANS AS WELL AS ELECTRICAL   PLANS. PLEASE SEE NFPA-101   7.10.8.3.1 ANY DOOR, PASSAGE, OR STAIRWAY THAT IS   NEITHER AN EXIT NOR A WAY OF EXIT ACCESS AND THAT IS   LOCATED OR ARRANGED SO THAT IT IS LIKELY TO BE MISTAKEN   FOR AN EXIT SHALL BE IDENTIFIED BY A SIGN THAT READS AS   FOLLOWS:   NO   EXIT   7.10.8.3.2 THE NO EXIT SIGN SHALL HAVE THE WORD NO IN   LETTERS 51 MM (2 IN.) HIGH, WITH A STROKE WIDTH OF 9.5   MM ( IN.), AND THE WORD EXIT IN LETTERS 25 MM (1 IN.)   HIGH, WITH THE WORD EXIT BELOW THE WORD NO, UNLESS SUCH   SIGN IS AN APPROVED EXISTING SIGN.       ** THIS IS REQUIRED WHETHER OR NOT COMMENT IS MADE BY   ANY OTHER TRADE.   *** PRO       6) NOTE: PLEASE CLARIFY JOCKEY PUMP WHICH RISER   INDICATES 30AMP DISCONNECT FUSED AT 30AMPS YET BRANCH   FROM ELP1 ONLY HAS 20AMP OCP WITH #12 CONDUCTORS.??   240.4,310.16, 430.   FBC 106.1.1 FOR CLARITY AND COORDINATION.   *** PRO       7) SEPARATE PERMITS FOR LIGHTNING PROTECTION, LOW   VOLTAGE SYSTEMS, FIRE ALARM, FIRE SPRINKLER. THE BASE   PLANS MAY BE REFERENCED FOR LOW VOLTAGE SYSTEM ONLY.   SEPARATE PLANS WILL BE REQUIRED FOR LP, FS AND FA.   THIS IS NOTED FOR REVIEW ONLY. NO RESPONSE OR CHANGES   ARE NEEDED ON PLANS OR SUBMITTED DOCUMENTS.                   **IMPORTANT**   ONCE AUDIT/REVIEWS ARE COMPLETE AND PLANS ARE PICKED UP   FOR CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE   ALL OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING.   DO NOT LEAVE ANY OLD/VOIDED SHEETS IN SETS.   PLEASE DO NOT ATTACH SUPPORTING DOCUMENTS TO PLANS. ANY   ADDITIONAL DOCUMENTATION SUCH AS PRODUCT APPROVALS,   SPEC/CUT SHEETS, CALCULATIONS ETC. SHOULD BE PLACED   INTO TWO SETS/FOLDERS/BINDERS ETC.   PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS   SHOULD BE SUBMITTED FOR REFERENCE.   THIS WILL HELP IN THE AUDIT/REVIEW PROCESS AND AVOID   ANY DELAYS.       IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected] 2008-12-12 17:11:31 REVIEW IS IN PROGRESS.   REVIEW WILL BE GOING INTO FAILED STATUS ONCE COMPLETED   AND NOTES WILL FOLLOW. Review Stop E ELECTRICAL Rev No 2 Status F Date 2008-10-27 Cont ID   Sent By dpalmer Date 2008-10-27 Time 16:49 Rev Time 0.00 Received By dpalmer Date 2008-10-27 Time 16:49 Sent To   Notes 2008-10-27 16:49:54     ** DENIED 2ND REVIEW**           1) NOTE: PLEASE SEE THE LETTER SUBMITTED FOR THE   BUILDING NOT TO BE OCCUPIED UNDER THE LOSS OF   NORMAL/MAIN POWER IS TO BE REVISED. THE LETTER STATES   THE FACILITY WILL NOT OPERATE HOWEVER THE LETTER NEEDS   TO STATE THE BUILDING WILL NOT BE OCCUPIED BY ANY   PERSONNEL. THE LETTER(S) NEED TO BE ORIGINAL AND   NOTARIZED. PLEASE SEE FS 117.05 FOR NOTARIES.   NFPA-101 7.8, 7.9       2) NOTE: THE PREVIOUS REVIEW REQUESTED THE REQUIRED   ENERGY CALCULATIONS TO BE SUBMITTED. AS THEY WERE NOT   SUBMITTED ON THE FIRST REVIEW THEY COULD NOT BE   REVIEWED. PLEASE SEE THE ENERGY CALCULATIONS AND THE   INPUT DATA REPORT NEED TO COORDINATE WITH THE PLANS.   THE INPUT DATA REPORT WILL BE NOTED BELOW AS IDR.   TWO SEPARATE CALCULATIONS WERE SUBMITTED. THE   *CERTIFICATIONS* SHEETS NEED TO BE COMPLETED WITH THE   SIGNATURE, DATE AND SEAL FROM THE RESPONSIBLE DESIGNER   OF RECORD. THE COVER SHEET WAS SIGNED AND SEALED.   EXAMPLES OF SOME INCONSISTENCIES OF THE SUBMITTED   CALCULATIONS AND THE IDR WILL BE NOTED.       FOR EXAMPLE: PLEASE SEE THE SQUARE FOOTAGE OF THE   CALCULATION COVER SHEET SHOWS A TOTAL OF 7022 SQ FT   TOTAL OF CONDITIONED AND UNCONDITIONED SPACE. THIS IS   NOT POSSIBLE AS THE SQUARE FOOTAGE SHOWN ON A001CR1   SHOWS NUMBERS FAR GREATER. THE SUBMITTED METHOD *A* IS   FOR WHOLE BUILDING.       FOR EXAMPLE: PLEASE SEE THAT NOT ALL EXTERIOR LIGHTS ON   PLANS ARE IN THE IDR> ONE FIXTURE TYPE ALONE WOULD BE   THE S-7. THIS IS A 70W FIXTURE BASE DON THE FIXTURE   LEGEND AND THERE ARE NO 70W FIXTURES ON THE IDR FOR   EXTERIOR LIGHTING. ** THESE ARE NOT EXEMPT EVEN IF FOR   THE SIGN** PLEASE SEE THE FBC CHAPTER 13 IN ORDER TO   FALL UNDER EXCEPTIONS FOR THESE NOT TO BE   INCLUDED.13-415.2.ABC.1.3   ** PLEASE SEE SHEET E123CR1 DOES NOT LIST THESE   FIXTURES AS PART OF THE CONTROLS EVEN AS THE SITE PLANS   CALL FOR SLP-25.       FOR EXAMPLE: THE FIXTURE S2 IS A 400W FIXTURE HOWEVER   THE IDR SHOWS 800W. IT WAS ASSUMED THAT EACH POLE WHICH   CONTAINS TWO FIXTURES WERE COUNTED AS ONE AND THIS IS   WHY THE IDR SHOWS 800W WHICH ACCOUNTS FOR BOTH   FIXTURES. HOWEVER AS THE IDR SHOWS A TOTAL OF 6-800W   FIXTURES, WHAT ABOUT THE FIXTURES ON THE POLES WHICH   INDICATES ONLY ONE S2 FIXTURE?   THIS WAS NOT ACCOUNTED FOR IN THE IDR.       FOR EXAMPLE: THE IDR INDICATES ALL * UNCOVERED PARKING   AREAS* AND THESE ASSOCIATED LIGHT FIXTURES. WHAT ABOUT   ALL OF THE OTHER FIXTURES WHICH ARE EXTERIOR FIXTURES   ON THE OUTSIDE OF THE BUILDING? BASED ON THE IDR, THE   LIGHTING PLANS AND THE FIXTURE LEGEND NONE OF THESE   FIXTURES WERE INCLUDED.   SEE E FIXTURE ALONE WHICH IS AN EXTERIOR WALL PACK.       FOR EXAMPLE: PLEASE SEE THE INTERIOR LIGHT FIXTURES AS   THERE ARE SEVERAL FIXTURES ON THE PLANS WHICH ARE NOT   IN THE IDR. ONE OF THESE ALONE WOULD BE THE TYPE *A*   FIXTURE.       ****** THESE ARE SOME EXAMPLES ONLY OF ITEMS ON THE   ELECTRICAL PLANS WHICH ARE NOT COORDINATED WITH THE IDR   AND THE SUBMITTED ENERGY CALCULATIONS. ALL AREAS,   TYPES, WATTAGES ETC NEED TO MEET THE MINIMUMS.   PLEASE SEE 13-415.2.ABC.1.1, .1.2 AND .1.3.   *******       3) NOTE: PLEASE BE MORE SPECIFIC TO THE TYPE OF   OCCUPANCY SENSOR DEVICES. THE SYMBOL LEGEND DOES NOT   EXPAND ON DEVICES FOR AREAS SUCH AS EGRESS PATHS WHICH   ARE NOW ADDED TO PLANS.   PLEASE INDICATE THE FAIL SAFE OPERATION FOR THESE   DEVICES AS REQUIRED PER FBC 1006.1.2, NFPA-101   7.8.1.2.2   DEVICES IN THE FIRE PUMP ROOM, MAIN ELECTRICAL ROOM AND   ELEVATOR EQUIPMENT ROOM ALSO NEED TO BE *FAIL SAFE ON*   OPERATION ON OCCUPANCY SENSING DEVICES.   PLEASE BE SURE THE SYMBOL LEGEND INDICATES THE TYPE AND   MAXIMUM TIME.       4) NOTE: PLEASE SEE THAT THE PREVIOUS REVIEW REQUESTED   INFORMATION ON THE FIRE PUMP, CONTROLLER ETC. THE   SUBMITTED PACKAGE DOES CONTAIN SHOP DRAWINGS/PRODUCT   APPROVALS WHICH DO CONTAIN THE INFORMATION HOWEVER SOME   OF THE SHEETS FOR THE FIRE PUMP ARE VERY FAINT AND NOT   READABLE.   PLEASE ALSO SHOW ON RISER, PLANS, SCHEDULE(S) WHERE AND   HOW THE JOCKEY PUMP IS BEING FED. COULD NOT LOCATE THIS   ON THE RISER ETC. SHEET E105CR1 INDICATES CIRCUITING TO   LP2, THIS IS A LIFE SAFETY SYSTEM, PLEASE EXPLAIN WHY   THIS IS NOT ON THE GENERATOR.   PLEASE SEE SAME SHEET E105CR1 WHICH DRAWING NOTE #44   INDICATES A 10HP FIRE PUMP. THIS SEEMS TO BE A   MISPRINT?   PLEASE BE SURE TO SEE NFPA-20 CHAPTERS 6 AND 7 AND ALSO   SEE NFPA-70 695.6.C.1, 695.5 A, B.       5) NOTE: PLEASE SEE THE SHEET E120C WHICH STILL SHOWS   THE PREVIOUS RISER WHICH INDICATED THE NUMEROUS MAINS   AND OTHER ITEMS FROM PREVIOUS REVIEW WHICH HAVE NOW   BEEN REVISED.   PLEASE COORDINATE PLANS/SHEETS.   THE PREVIOUS NOTES GAVE SOME EXAMPLES OF COORDINATION   NEEDED.   EXAMPLE: PLEASE SEE E119C WHICH NOTES 3,4 AND 5   INDICATE TWO PANELS AND A TRANSFORMER WHICH IS NOT ON   THE PRIMARY RISER SHEET. THERE ARE NO PANEL SCHEDULES   FOR THESE TWO PANELS ON THE SHEETS WITH THE OTHER PANEL   SCHEDULES AND THE 112.5 KVA TRANSFORMER IS NOT LISTED   ON EITHER OF THE TWO TRANSFORMER SCHEDULES ON SHEET   E107CR1 YET THIS IS NOTED ON SHEET E120C. PLEASE   EXPLAIN THE WORK SHOWN ON THESE OTHER SHEETS. ARE THESE   PERMITTED UNDER THIS SAME PERMIT OR SCOPE OF WORK?   NEC 230,240, 250, 215.5, 450ETC   FBC 106.1.1 FOR CLARITY AND COORDINATION OF PLANS.       6) NOTE: NEW NOTE: PLEASE EXPLAIN SUPPLEMENTAL LIGHTING   PLAN.   NEC 2005   FBC 106.1.1 FOR ADDITIONAL INFORMATION/CLARITY       7) NOTE: PLEASE SEE 13-415.1.ABC.1.1,.1.2, AND .1.3.   THE OVER RIDES INDICATED ARE NOTED ON PLANS WITH NOTES   FOR LABELS AND PHONETIC LETTERING HOWEVER PLEASE SEE   SECTIONS NOTED. THE CODE REQUIRES THE OCCUPANT TO SEE   ALL LIGHTING WHICH IS BEING OVER RIDDEN OR MEET THE   EXCEPTION WHICH IS NOT ONLY DETAILED SIGNAGE FOR ALL   AREAS BEING OVER RIDDEN BUT ALSO FOR REQUIRED *PILOT   LIGHTS* OR * INDICATOR LIGHTS* OF SOME KIND.       8) NOTE: PLEASE SEE NFPA-101 7.8 AND 7.9 OF PREVIOUS   NOTES WITH RESPECT TO EGRESS LIGHTING LEVELS UNDER   NORMAL AND EMERGENCY CONDITIONS.   SOME LEVELS SHOWN ARE INDICATING LEVELS OF AVERAGE   BELOW THE 10FT CANDLES UNDER NORMAL CONDITIONS. THIS   LEVEL OF LIGHTING SHOULD BE FIGURED FROM THE STAIR   AREAS ONLY AND NOT FIGURING IN OTHER AREAS OF AVERAGE.   IF THERE ARE FIXTURES WHICH CONTRIBUTE TO THE LIGHTING   LEVELS THEN PLEASE CALL TO GO OVER CONTRIBUTIONS. THE   RESPONSE LETTER MENTIONS SOME STAIRS ARE NOT EGRESS   LOCATIONS USED FOR EXITING.   PLEASE SEE THE LIFE SAFETY CODE AS THE LIGHTING LEVEL   DOES APPLY TO EGRESS PATHS FOR ALL NOT ONLY THE GENERAL   PUBLIC.   PLEASE SEE NFPA-101 7.10.8.3,.3.1 AND .3.2 WHICH   REQUIRES SIGNAGE FOR ANY DOOR WHICH IS NOT AN EXIT DOOR   TO BE LABELED AS SUCH. PLEASE SEE SECTIONS FOR MINIMUM   SIZE AND WORDING.       9) NOTE: MSB ON SHEET E120C STILL INDICATES GFIC   PROTECTION. RESPONSE AND OTHER SHEETS WERE REVISED TO   GFP FOR PROTECTION OF MAIN SWITCH GEAR EQUIPMENT.       10) NOTE: PLEASE SEE THE RISER IS STILL SHOWING   EQUIPMENT GROUNDING FROM FPL TRANSFORMER TO THE FIRST   MEANS OF DISCONNECT WHICH IS NOT PERMITTED. THE   RESPONSE MENTION FIRE PUMP CALCULATIONS PROVIDED AND   THE MISINTERPRETATION OF THE CODE WITH RESPECT TO THE   EQUIPMENT GROUNDING CONDUCTOR.   250.24C REQUIRES THE *GROUNDED* CONDUCTOR TO BE BROUGHT   TO THE FIRST MEANS OF DISCONNECT. AS THE CODE REQUIRES   BINDING OF THE GROUNDING CONDUCTOR AT THE FIRST MEANS   OF DISCONNECT IF AN *EQUIPMENT GROUNDING* CONDUCTOR IS   IN THE SAME CONDUIT THIS WOULD CREATE OBJECTIONABLE   CURRENTS PER 250.6.   ** PLEASE CALL TO GO OVER AS THERE MUST BE A LOSS IN   COMMUNICATION.   ** RESPONSE ALSO MENTIONS THE PLANS/RISER WAS REVISED   HOWEVER THE PLANS/RISER STILL INDICATES THE SAME.       11) NOTE: PLEASE SEE PREVIOUS NOTES WITH RESPECT TO   REQUIRED DEDICATED CIRCUITS FOR ELEVATOR EQUIPMENT   ROOMS. 645.23,22,24.   RESPONSE MENTIONS THE PLANS AND PANEL SCHEDULES HAVE   BEEN REVISED HOWEVER PLEASE SEE SHEET E105CR1. BASED ON   PLANS RECEPTACLES FED FROM RP2-35 ARE NOT MEETING THIS   REQUIREMENT.       12) NOTE: NEW NOTE: PLEASE PLACE NOTE ON PLANS FOR THE   *COMMUNICATION ROOM*. AS THIS IS NOT AN IT ROOM BY   DEFINITION IN NEC 645.2 PLEASE PLACE NOTE ON PLANS   WHICH STATES * NO WIRING METHODS FROM NEC 645   PERMITTED*       13) NOTE: NOW THAT THE PLANS INDICATE THE GENERATOR   LOCATED OUTSIDE PLEASE SEE NFPA-110 CHAPTER 7 FOR THE   INSTALLATION REQUIREMENTS OF OUTDOOR UNITS. PLEASE   INDICATE THE ELEVATION MEETING THE SLOSH CHARTS/100   YEAR FLOOD. 7.3                                   **IMPORTANT**   ONCE AUDIT/REVIEWS ARE COMPLETE AND PLANS ARE PICKED UP   FOR CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE   ALL OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING.   DO NOT LEAVE ANY OLD/VOIDED SHEETS IN SETS.   PLEASE DO NOT ATTACH SUPPORTING DOCUMENTS TO PLANS. ANY   ADDITIONAL DOCUMENTATION SUCH AS PRODUCT APPROVALS,   SPEC/CUT SHEETS, CALCULATIONS ETC. SHOULD BE PLACED   INTO TWO SETS/FOLDERS/BINDERS ETC.   PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS   SHOULD BE SUBMITTED FOR REFERENCE.   THIS WILL HELP IN THE AUDIT/REVIEW PROCESS AND AVOID   ANY DELAYS.           IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.               DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]     Review Stop E ELECTRICAL Rev No 1 Status F Date 2008-07-30 Cont ID   Sent By dpalmer Date 2008-07-30 Time 16:29 Rev Time 0.00 Received By dpalmer Date 2008-07-30 Time 16:29 Sent To   Notes 2008-08-01 08:26:49 ** NOTE ADDED           ** ALL CIRCUITING FOR EMEGENCY LIGHTING SHALL MEET   700.12F. MANY LOCATIONS ON PLANS DO NOT MEET THE   EXCEPTIONS IN THE CODE. 2008-07-30 16:29:24                                                                             ** DENIEDAUDIT **       *** IT IS IMPORTANT TO KNOW THAT INFORMATION AND   DOCUMENTATION NOT SUBMITTED DOES NOT COMPLETE PACKAGE   FOR AUDIT AND DOES NOT PROVIDE THE MINIMUM REQUIRED BY   THE FLORIDA BUILDING CODE AND ALL OTHER APPLICABLE LAWS   AND ORDINANCES.       1) NOTE: *** PLEASE KNOW ALL PLANS AND DOCUMENTS WILL   BE RETAINED BY THIS OFFICE. PLANS AND SUPPORTING   DOCUMENTS MAY BE FORWARDED TO THE LICENSING BOARD FOR   BUILDING CODE ADMINISTRATORS AND INSPECTORS BOARD ALONG   WITH FLORIDA BOARD OF ENGINEERS FOR REVIEW OF SAID   PLANS AND DOCUMENTS.       2) NOTE: PLEASE SEE THERE ARE SEVERAL DOCUMENTS IN   PACKAGE SUBMITTED IN WHICH RAISED SEALS ARE PLACED OVER   PHOTO-COPIED SIGNATURES AND DATES. THIS IS NOT   PERMITTED UNDER FAC 61G15-23.002 AND FS 471.025. PLEASE   KNOW THIS SAME COMPANY IN WHICH MANY OF THESE DOCUMENTS   WERE DONE THIS MANOR HAS BEEN NOTIFIED ON PREVIOUS   PROJECTS THAT THIS IS NOT ACCEPTABLE UNDER FLORIDA LAW   HOWEVER THIS IS STILL BEING DONE.       3) NOTE:PLEASE PROVIDE AFFIDAVITS AS REQUIRED PER FS   553.791 FOR EACH TRADE WHERE EACH AFFIDAVIT ACTUALLY   DOES LIST THE SHEETS.   PLACING ONE AND NOTING SEE ATTACHED IS NOT ACCEPTABLE.           4 NOTE: PLEASE PROVIDE NOTICE TO BUILDING OFFICIAL AS   REQUIRED. FS553.791       5) NOTE: PLEASE DO NOT SUBMIT REVISION TO THE STAMPED   PLANS WHEN THE       6) NOTE: PLEASE SUBMIT ENERGY CALCULATIONS/LIGHTING   PERFORMANCE CALCULATIONS PER 13-415.2.ABC.1.1, .1.2 AND   .1.3.   *** IT IS IMPORTANT TO KNOW THAT INFORMATION AND   DOCUMENTATION IS NOT COMPLETE.       7) NOTE: PLEASE KNOW THE LIGHTING PROTECTION SYSTEM   WILL BE REQUIRED TO BE UNDER SEPARATE PERMITS AND SHALL   CONTAIN NOTES AND DESIGN PER NFPA-780.       8) NOTE: AN AUDIT OF SIGNED, DATED AND SEALED   ELECTRICAL PLANS WAS NOT DONE AS NONE OF THESE CONTAIN   ANY STAMPS FROM THE PRIVATE PROVIDER.   FS 553.791       9) NOTE: PLEASE SEE FBC 11-4.28.1,.2 AND .3. PLEASE   PROVIDE ALL MINIMUM LEVELS FOR FIRE ALARM DEVICES TO   MEET ADA REQUIREMENTS. PLEASE BE SURE TO STATE THE   LEVELS OF DEVICES.       10) NOTE: THE PLANS AND NOTES MENTIONS AUTOMATE   LIGHTING CONTROL SYSTEMS WITH CONTACTORS HOWEVER   COMPLETE DETAILS OF SYSTEMS, OVER RIDES, OVER RIDE   TIMES ETC ARE NOT LOCATED ON PLANS.   PLEASE SEE THERE ARE SEVERAL LOCATIONS INCLUDING   MEZZANINE LIGHTING WHICH DO NOT INDICATE ANY LIGHTING   CONTROLS FOR AUTOMATED SYSTEMS. THESE AREAS DO INDICATE   STANDARD SWITCHING DEVICES WHICH DO NO MEET   13-415.1.ABC.1.1,.1.2, .1.3.   PLEASE ALSO SEE OTHER LOCATIONS ON E-112   ** THIS IS NOT ALL LOCATIONS AS THERE ARE SEVERAL   SECTIONS ON PLANS WHICH DO NOT MEET MINIMUM CODE       11) NOTE: PLEASE PROVIDE COMPLETE INFORMATION ON   LIGHTING CONTROLS FOR EXTERIOR LIGHTING MEETING FBC   13-415.1.ABC.1.4       11) NOTE: PLEASE PROVIDE WORST CASE VOLTAGE DROP PER   13-413.1.ABC.1.1, .1.2       12) NOTE: PLEASE PROVIDE NOTES ON PLANS PER   13-413.1.ABC.2.1,.2.2.       13) NOTE: PLEASE SEE SOME AREAS AS NOTED ON SHEET E102   MENTION TO SEE E112, HOWEVER THESE SAME AREAS WHICH   MENTION TO SEE ENLARGED PLANS ARE NOT SHOWN. PLEASE SEE   SOME OF THESE AREAS ARE BREAK ROOM, BATHROOMS ETC WHICH   ARE NOT ON E112.       14) NOTE: PLEASE COMPLETE AND COORDINATE ALL SYMBOLS ON   PLANS. THIS INCLUDES ALL DEVICES SHOWN FOR LIGHTING   CONTROLS WHICH ARE NOT ON SYMBOL LEGEND. AN EXAMPLE OF   THIS IS SM.   FBC 13-415, NEC ALL   FBC 106.1.1 FOR CLARITY OF PLANS AND MINIMUM   INFORMATION. 106.3.5.1.2       15) NOTE: PLEASE SUBMIT COMPLETE PHOTO-METRICS TO MEET   THE MINIMUM FOR LIFE SAFETY FOR ALL EGRESS PATHS.   PLEASE SEE SOME AREAS SUCH AS STAIRS INCLUDING THAT OF   EXTERIOR STAIRS DO NOT SHOW ANY BATTERY BACK UP   LIGHTING AS REQUIRED.   PLEASE SEE SECTIONS 7.8.1.3,7.9.2.1,79.2.2.   FAC 61G15-33.004   ** EGRESS LIGHTING SHALL BE PROVIDED UNDER NORMAL AND   EMERGENCY CONDITIONS OUT OF THE BUILDING. PLEASE BE   SURE TO SEE THE LEVELS DID INCREASE UNDER THE 2003   NFPA-101       16) NOTE: PLEASE BE SURE THE FOLLOWING CODES ARE STATED   ON ELECTRICAL PLANS AT A MINIMUM FOR THIS TRADE. FBC   2004 W/2007 REVISIONS.   2003 NFPA-101   2005 NFPA-70   2002 NFPA-72   2003 NFPA-20   2002 NFPA-110       17) NOTE: PLEASE COMPLETE ALL INFORMATION ON PLANS FOR   FIRE PUMP, FIRE PUMP CONTROLLER. PLEASE KNOW AS THE   INFORMATION ON THE FP IS NOT COMPLETE PLEASE SUBMIT   COMPLETE PLANS FOR MINIMUM. PLEASE KNOW THAT CHAPTERS   OF THEN CODES WILL BE CITED NOT SECTIONS AS THERE TOO   MANY SECTIONS OF THE CODE MISSING.   PLEASE INDICATE LOCK ROTOR MAXIMUM OVER CURRENT   PROTECTION.   PLEASE SEE NFPA-70 695.4B1 (1) OVER-CURRENT DEVICE   SELECTION THE OVER-CURRENT PROTECTIVE DEVICE(S) SHALL   BE SELECTED OR SET TO CARRY INDEFINITELY THE SUM OF THE   LOCKED-ROTOR CURRENT OF THE FIRE PUMP MOTOR(S) AND THE   PRESSURE MAINTENANCE PUMP MOTOR(S) AND THE FULL-LOAD   CURRENT OF THE ASSOCIATED FIRE PUMP ACCESSORY EQUIPMENT   WHEN CONNECTED TO THIS POWER SUPPLY. THE REQUIREMENT TO   CARRY THE LOCKED-ROTOR CURRENTS INDEFINITELY SHALL NOT   APPLY TO CONDUCTORS OR DEVICES OTHER THAN OVER-CURRENT   DEVICES IN THE FIRE PUMP MOTOR CIRCUIT(S).       PLEASE SEE NFPA-20 CHAPTERS 9, 10 ETC   PLEASE SUBMIT MANUFACTURES SPEC/CUT SHEETS FOR THE FIRE   PUMP AND FIRE PUMP CONTROLLER.   110.3,90.7, NFPA-20.   ** AS PLANS AND INFORMATION IS NOT COMPLETE MANY ITEMS   FOR MINIMUM CODE COMPLIANCE CAN NOT BE DETERMINED AT   THIS TIME.       18) NOTE: PLEASE SEE 230.2 AS THE NUMBER OF SERVICES   SHOWN ON PLANS ARE NOT PERMITTED AND NOT ALL MEET THE   EXCEPTIONS IN THE CODE AT THIS TIME.   PLEASE LOOK AT RISER AS THE EQUIPMENT FED FROM MSB ARE   BEING NOTED AS *MAINS*.       19) NOTE: PLEASE SEE 230.95, 240.13 AS THE 3000AMP MAIN   INDICATE GFIC PROTECTION. SHOULD THIS NOT BE GFP FOR   GROUND FAULT PROTECTION? GFCI IS FOR PERSONNEL.       20) NOTE: PLEASE SUBMIT AND SHOW A COMPLETE GROUNDING   ELECTRODE RISER FOR ALL TRANSFORMERS AND COMMON   SYSTEM.   250.58, 250.66       21) NOTE: PLEASE SEE THERE ARE LOCATIONS WHERE   EQUIPMENT GROUNDING CONDUCTORS ARE BEING SHOWN BEFORE   THE FIRST MEANS OF DISCONNECT WHICH IS NOT PERMITTED.   PLEASE CLARIFY THE #4 TO FIRE PUMP CONTROLLER. PLEASE   BE SURE TO SIZE THE NEUTRAL (GROUNDED CONDUCTOR) AS   THIS IS REQUIRED TO CONTAIN A NEUTRAL TO THE FIRST   MEANS OF DISCONNECT. IN NO CASE MAY THIS BE SMALLER   THAN THE GROUNDING ELECTRODE   CONDUCTOR.250.4,250.6,250.50,ETC   THIS IS ALSO NOTED FOR THE 3000AMP MAIN AS AN EQUIPMENT   GROUNDING CONDUCTOR IS ALSO SHOWN BEFORE THE FIRST   MEANS OF DISCONNECT WHICH IS NOT PERMITTED. THIS   CREATES OBJECTIONABLE CURRENTS.       22) NOTE: PLEASE SEE 230.95, 240.13, 700.7D, 700.26,   NFPA-110 6.2.1.5   AS THE TRANSFER SWITCH ON PLANS DOES NOT INDICATE HOW   MANY POLES. BASED ON THE CODE SECTIONS GIVEN THIS IS   REQUIRED TO BE A FOUR POLE UNIT. THE FOLLOWING TEXT MAY   BE OF USE FOR THE TRANSFER SWITCH. THIS WORDING IS FROM   ONE WHITE PAPER FROM ONE MANUFACTURE AND THERE ARE   SEVERAL OTHERS AVAILABLE.       *WHERE GROUND FAULT PROTECTION IS TRIGGERED BY THE CODE   AND AN ALTERNATE POWER SUPPLY IS INCLUDED, SWITCHING OF   THE NEUTRAL BECOMES NECESSARY. THE CIRCUIT SHOWN ABOVE   ILLUSTRATES SUCH A CIRCUMSTANCE.   THE SERVICE IS LARGER THAN 1,000 AMPS. CONSEQUENTLY,   GROUND FAULT PROTECTION IS REQUIRED AT THE MAIN SERVICE   DISCONNECT AT A MINIMUM. IF IT IS INSTALLED THERE AND   THE GENERATOR NEUTRAL GROUNDING WAS THROUGH A SOLID   CONNECTION TO THE MAIN SERVICE NEUTRAL, A GROUND FAULT   WHEN THE GENERATOR IS FEEDING   THE LOAD WILL CAUSE THE MAIN SERVICE DISCONNECT TO   OPEN. THIS WILL NOT DISCONNECT THE ARCING FAULT FROM   THE GENERATOR. COORDINATION IS THUS LOST.*       THIS WAS FROM ASCO WHITE PAPER PAGE #5. OTHERS SUCH AS   CATERPILLAR ETC HAVE MUCH OF THE SAME.           23) NOTE: PLEASE SEE NFPA-110 9.6.2.2 AND INDICATE THE   MINIMUM TIMES FOR ON-SITE FUEL AS REQUIRED FOR POWER   FOR FIRE PUMP ALONG WITH OTHER EMERGENCY LOADS. 9.6.2.2   THE FUEL SUPPLY CAPACITY SHALL BE SUFFICIENT TO PROVIDE   8 HOURS OF FIRE PUMP OPERATION AT 100 PERCENT OF THE   RATED PUMP CAPACITY IN ADDITION TO THE SUPPLY REQUIRED   FOR OTHER DEMANDS.           24) NOTE: PLEASE KNOW BATTERY BACK UP LIGHTING SHALL BE   REQUIRED FOR THE EGRESS LIGHTING PATHS PER NFPA-7.8,   7.9.PLEASE KNOW THIS BUILDING SHALL NOT RELY ON THE   SINGLE TRIPPING OF A BREAKER, SWITCHING OF A DEVICE TO   LEAVE ANY ONE ARE IN TOTAL DARKNESS.   PLEASE BE SURE OTHER LOCATIONS SUCH AS THE MAIN   ELECTRICAL ROOM, FIRE PUMP ROOM, ELEVATOR EQUIPMENT   ROOM ALSO CONTAIN BATTERY BACK UP LIGHTING.       25) NOTE: PLEASE SUBMIT THE PLANS WITH THE COMPLETED   INFORMATION FOR LOCATION OF THE GENERATOR. THE RISER   SHOWS A GENERATOR HOWEVER WHERE IS THIS UNIT GOING TO   BE INSTALLED? PLEASE SEE OTHER PLANS SUCH AS SITE,   MECHANICAL, BUILDING ETC DO NOT SHOW ANY LOCATIONS.       26) NOTE: PLEASE SEE NEC 645.,23AS THE MINIMUM   REQUIRED DEDICATED CIRCUITS ARE NOT LOCATED ON PLANS.   IN FACT ONE EXAMPLE OF NON-COMPLIANCE IS THE FACT THE   LIGHTING IN THE MACHINE ROOM WHICH IS REQUIRED TO BE ON   A DEDICATED CIRCUIT PER 620.23 IS SHOWN CIRCUITED TO   OTHER NORMAL LIGHTING OUTSIDE OF THIS ROOM.   PANEL SCHEDULE INDICATES OTHERS PER 620.22, 620.24   HOWEVER PLANS DO NOT SHOW SOME OF THESE CIRCUITS,   LIGHTS, PIT LIGHTING, GFI RECEPTACLES ETC. RECEPT SHOWN   HOWEVER SECTIONS AS NOTED REQUIRE GFCI PROTECTION. THIS   IS NO ON PLANS OR ON PANEL SCHEDULE   IF THE PANEL SCHEDULE ONLY INDICATES *RECEPTACLES FOR   EXAMPLE ON RP1-16 THE DEDICATE CIRCUIT IS NOT   DETERMINED           27) NOTE: PLEASE SEE NFPA-110 CHAPTER 7, 7.3.3 AS THE   MINIMUM LIGHTING IN ANY GENERATOR ROOM SHALL MEET THIS   MINIMUM.   PLEASE KEEP IN MIND AS THE GENERATOR IS NOT SHOWN THIS   IS GIVEN FOR INFORMATION ONLY.   PLEASE SEE THE FOLLOWING FOR LOCATION AS THIS WAS NOT   SHOWN AT THIS TIME.       7.2 LOCATION.   7.2.1 THE EPS SHALL BE INSTALLED IN A SEPARATE ROOM FOR   LEVEL 1 INSTALLATIONS. EPSS EQUIPMENT SHALL BE   PERMITTED TO BE INSTALLED IN THIS ROOM.   7.2.1.1 THE ROOM SHALL HAVE A MINIMUM 2-HOUR FIRE   RATING OR BE LOCATED IN AN ADEQUATE ENCLOSURE LOCATED   OUTSIDE THE BUILDING CAPABLE OF RESISTING THE ENTRANCE   OF SNOW OR RAIN AT A MAXIMUM WIND VELOCITY REQUIRED BY   LOCAL BUILDING CODES.   7.2.1.2 NO OTHER EQUIPMENT, INCLUDING ARCHITECTURAL   APPURTENANCES, EXCEPT THOSE THAT SERVE THIS SPACE,   SHALL BE PERMITTED IN THIS ROOM.   7.2.2 EPSS EQUIPMENT SHALL NOT BE INSTALLED IN THE SAME   ROOM WHERE THE NORMAL ELECTRICAL SERVICE EQUIPMENT IS   INSTALLED.   7.2.2.1 TRANSFER SWITCHES SHALL BE PERMITTED TO BE   INSTALLED IN THE NORMAL ELECTRICAL SERVICE ROOM WHERE   TWICE THE CLEARANCE REQUIRED BY ARTICLE 110.26(A) OF   NFPA 70, NATIONAL ELECTRICAL CODE, EXISTS BETWEEN   EQUIPMENT ENCLOSURES.   7.2.3*THE ROOMS, SHELTERS, OR SEPARATE BUILDINGS   HOUSING LEVEL 1 OR LEVEL 2 EPSS EQUIPMENT SHALL BE   DESIGNED AND LOCATED TO MINIMIZE THE DAMAGE FROM   FLOODING, INCLUDING THAT CAUSED BY THE FOLLOWING: (1)   FLOODING RESULTING FROM FIRE FIGHTING   (2)SEWER WATER BACKUP   (3)SIMILAR DISASTERS OR OCCURRENCES   7.2.4*MINIMIZING THE POSSIBILITY OF DAMAGE RESULTING   FROM INTERRUPTIONS OF THE EMERGENCY SOURCE SHALL BE A   DESIGN CONSIDERATION FOR LEVEL 1 AND LEVEL 2 EPSS   EQUIPMENT.   7.2.5 THE EPS EQUIPMENT SHALL BE INSTALLED IN A   LOCATION THAT PERMITS READY ACCESSIBILITY AND A MINIMUM   OF 76 CM (30 IN.) FROM THE SKID RAILS' OUTERMOST POINT   IN THE DIRECTION OF ACCESS FOR INSPECTION, REPAIR,   MAINTENANCE, CLEANING, OR REPLACEMENT. THIS REQUIREMENT   SHALL NOT APPLY TO UNITS IN OUTDOOR HOUSINGS.       28) NOTE: PLEASE SEE 450.3 AS THE MAXIMUM OVER CURRENT   PROTECTION ON THE TRANSFORMER TRP1 SHALL BE 125% UNLESS   MEETING EXCEPTIONS. AS THE PLANS DO NOT INDICATE WHAT   TYPE OF UNIT THIS IS PLEASE SEE SECTION AS NOTED.       29) NOTE: PLEASE SEE 408.4 AS THE CIRCUITS SHOWN ON   PANEL SCHEDULES SHALL BE SPECIFIC TO ROOMS AND AREAS IN   WHICH THEY FEED. STATING *RECEPTACLES* OR *LIGHTING* IS   NOT ACCEPTABLE. PLEASE KNOW A NUMERICAL OR ALPHA   DESIGNATION MAY BE USED.       30) NOTE: PLEASE INCLUDE FOOTER STEEL AS PART OF THE   GROUNDING ELECTRODE SYSTEM AS REQUIRED PER 250.50.       31) NOTE: PLEASE SEE RISER AS ERP1 INDICATES A FEED TO   PANEL ERPSH HOWEVER THE PANEL SCHEDULE FOR ERP1 DOES   NOT INDICATE ANY SUB FEED FOR PANEL ERPSH.   PLEASE COMPLETE WITH OCP, CONDUCTORS, LOADS ETC.   408.4,310.16,240.4,220,ETC       32) NOTE: PLEASE SUBMIT AND SHOW COMPLETE LOAD   CALCULATIONS PER NEC 220.   PLEASE BE SURE ALL CONTINUOUS LOADS ALONG WITH LARGEST   MOTOR LOADS ARE FIGURED SHOWN AT 125%.   PLEASE BE SURE THE WATER HEATER LOADS ARE FIGURED AND   SHOWN AT 125%. 220,12,220.14,220.42,,220.44,220.50, ETC   215.3,230.42, 422.13 FOR CONTINUOUS LOADS.   FBC 106.1.1, 106.3.5.1.2 FOR CLARITY AND MINIMUM   REQUIRED ON PLANS.       33) NOTE: PLEASE SEER RISER AS LPSH INDICATES A FEED TO   PANEL RPSH YET THERE IS NO BREAKER, LOAD, CIRCUIT   LISTED ON PANEL LPSH FOR THIS NEW PANEL.   PLEASE COMPLETE.   240.4,220,310.16 ETC       34) NOTE: PLEASE PROVIDE GROUNDING ELECTRODE   RISER/DIAGRAM FOR SCALE HOUSE PER   250.50,250.30,250.32.       35) NOTE: PLEASE SEE THE RISER SHOWS THE TRANSFORMER AT   THE SCALE HOUSE AS TRP-SH WHICH BY THE TRANSFORMER   CALLS FOR THIS UNIT AS A 30KVA UNIT YET THE LEGEND AND   PLANS ON SHEET E-112 INDICATES THIS SAME UNIT AT THE   SCALE HOUSE IS SHOWN AS 15KVA.   PLEASE KNOW AS BOTH UNITS ARE SHOWN WITH TWO DIFFERENT   SIZES THE OVER CURRENT PROTECTION ETC CAN NOT BE   DETERMINED AS CODE COMPLIANT.   PLEASE COORDINATE   450.3, 240.21, 310.16, 240.4 ETC.       36) NOTE: PLEASE SEE MAIN ELECTRICAL ROOM PART ROOM   PLAN WHICH INDICATES ANOTHER 15KVA TRANSFORMER YET THE   ELECTRICAL TRANSFORMER LEGEND ON SHEET ON E-107 DOES   NOT INDICATE ANY 15K TRANSFORMERS. AS THESE DOE NOT   COORDINATE DETERMINATION FOR CODE COMPLIANCE CAN NOT BE   DONE.   240.21,450.3,310.16 ETC   FBC 106.1.1 FOR COORDINATION AND CLARITY OF PLANS.       37) NOTE: PLEASE SUBMIT THE MANUFACTURES SPECS/CUT   SHEETS ON THE ATS, GENERATOR, AS NOTED ABOVE FOR OTHER   EQUIPMENT. 110.3,90.7           ** PLEASE KNOW AS THERE IS INFORMATION AND   DOCUMENTATION NOT YET SUBMITTED FOR AUDIT THERE MAY   VERY WELL BE NEW COMMENTS ON THE FOLLOWING AUDIT WHICH   CAN NOT BE MADE AT THIS TIME.       ** IF THERE ARE ANY QUESTIONS OR IF THE COMMENTS ARE   NOT CLEAR IN ANY MANOR PLEASE DO NOT HESITATE IN   CONTACTING THIS OFFICE.           IMPORTANT**   ONCE AUDIT/REVIEWS ARE COMPLETE AND PLANS ARE PICKED UP   FOR CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE   ALL OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING.   DO NOT LEAVE ANY OLD/VOIDED SHEETS IN SETS.   PLEASE DO NOT ATTACH SUPPORTING DOCUMENTS TO PLANS. ANY   ADDITIONAL DOCUMENTATION SUCH AS PRODUCT APPROVALS,   SPEC/CUT SHEETS, CALCULATIONS ETC SHOULD BE PLACED INTO   TWO SETS/FOLDERS/BINDERS ETC.   PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS   SHOULD BE SUBMITTED FOR REFERENCE.   THIS WILL HELP IN THE AUDIT/REVIEW PROCESS AND AVOID   ANY DELAYS.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected] Review Stop ENG ENGINEERING CSD Rev No 4 Status P Date 2008-11-19 Cont ID   Sent By mgonzale Date 2008-11-19 Time 10:55 Rev Time 1.00 Received By mgonzale Date 2008-11-19 Time 10:54 Sent To   Notes 2008-11-19 10:55:03 - PASSED -       ENGINEER HAS COMPLIED WITH ALL REQUESTS SET FORTH BY   THE ENGINEERING DEPT.       MANUEL J GONZALEZ, PROJECT COORDINATOR (561) 494-1040   LOCATION ADDRESS:   CITY OF WEST PALM BEACH   ENGINEERING SERVICES DEPARTMENT   1000 - 45TH STREET, SUITE 15   WEST PALM BEACH FL 33407   CITY'S WEB SITEHAS ALL OUR REFERENCE MATERIAL YOU NEED   TO COMPLY:   FEEL FREE TO SEE THE LINKS BELOW:   WWW.CITYOFWPB.ORG       MAILING ADDRESS:   CITY OF WEST PALM BEACH   ENGINEERING SERVICES DEPARTMENT   P.O. BOX 3506   WEST PALM BEACH FL 33401   TELEPHONE:   45TH STREET OFFICE : 561-494-1040   45TH DIRECT: 561-494-1085   FAX: 561-494-1117   CITY HALL OFFICE: (561) 805-6723   CITY HALL DIRECT: (561) 805-6327   CITY HALL FAX: (561) 805-6731 OR 805-6676   NEXTEL: 561-644-7301   NEXTEL DIRECT CONNECT: 159*28165*38   EMERGENCIES:   CENTRAL OPERATIONS CENTER (DISPATCH) 561-822-2210   E-MAIL:   [email protected]             Review Stop ENG ENGINEERING CSD Rev No 3 Status P Date 2008-11-05 Cont ID   Sent By mgonzale Date 2008-11-05 Time 12:43 Rev Time 1.00 Received By mgonzale Date 2008-11-05 Time   Sent To ENG Notes 2008-11-05 12:42:56 ENGINEER HAS POMPLIED WITH ALL REQUESTS SET FORTH BY   THE ENGINEERING DEPT. INCLUDES WATER, SEWER AND STORM   ISSUES.   MANNY GONZALEZ, PROJECT COORDINATOR   CITY OF WPB ENGINEERING (561) 494-1085 Review Stop ENG ENGINEERING CSD Rev No 2 Status F Date 2008-09-23 Cont ID   Sent By rchokshi Date 2008-09-23 Time 10:46 Rev Time 0.00 Received By rchokshi Date 2008-09-23 Time 10:41 Sent To   Notes 2008-09-23 10:46:04 FAILED FOR FOLLOWING REASONS:       1. PLEASE SHOW ON DRAWINGS THE SILT FENCE DETAILS &   TURBIDITY DETAILS OF POLLUTION PREVENTION . PLEASE SHOW   ON DRAWINGS THE SILT FENCE AROUND THE WHOLE SITE, &   TURBIDITY AROUND CATCH BASINS DURING CONSTRUCTION AND   ALL DEMOLITION PHASE. HEIGHT OF FENCE SHOULD BE HIGH   ENOUGH PER FDEP TO STOP DUST PARTICLES.       2. PLEASE PROVIDE A COPY OF BOND FOR ORDINANCE NO.   4060-07:       ALL DEMOLITION AND NEW CONSTRUCTION PERMITS, WITH   EXCEPTION OF SINGLE FAMILY, DUPLEX AND ACCESSORY   APARTMENT, SHALL POST BONDS OR DEPOSITS FOR THE   FOLLOWING:       1. EROSION CONTROL, AND   2. LAND STABILIZATION       THE AMOUNT OF THE EROSION CONTROL AND LAND   STABILIZATION BONDS SHALL BE DETERMINED BY THE ENGINEER   OF RECORD USING THE CURRENT CITY COST SCHEDULE AND   VERIFIED BY THE CITY'S ENGINEERING SERVICES DEPT.   PLEASE CONTACT BRIAN MOREE, ENG SERVICES CONSTRUCTION   SUPERVISOR, AT 561- 494 -1040 FOR MORE INFORMATION.       UPON VERTICAL CONSTRUCTION COMMENCEMENT, PAYMENT IN   FULL OF ALL APPLICABLE FEES, AND COMPLIANCE WITH ALL   TERMS AND CONDITIONS OF ANY POSTED BOND, THE PERMITTEE   MAY REQUEST RELEASE OF THE BONDS OR DEPOSITS.       A COPY OF ORDINANCE NO. 4060-07 MAY BE OBTAINED FROM   THE CITY CLERK'S OFFICE LOCATED ON THE FIRST FLOOR.       3. PLEASE SHOW ON DRAWING ALL CITY STANDARDS NOTES FOR   SIDEWALK, DRIVEWAY, APPROACH, PARKINGS, HANDICAP   PARKINGS, DUMPSTER ENCLOSURE, YOU CAN GET A C D FOR ALL   CITY STANDARDS NOTES FROM 1000, 45 STREET, ENGINEERING   SERVICES, PHONE# 494-1040       4. PLEASE SHOW ON DRAWINGS DUMPSTER & ITS ENCLOSURE   DETAILS PER CITY OF WPB, & LOCATION ON DWG, LOCATION   MUST BE ACCESSIBLE FOR PICKUP TRUCK.       5. PLEASE SHOW ON DRAINAGE DRAWING THE SITE AREA,   GREEN, LAKE,PARKING AREA, IMPERVIOUS,PERVIOUS AREA YOU   ARE DEVELOPING FOR THIS PROJECT . PLEASE MAKE SURE   THESE AREAS SHOWN ON DRAINAGE DRAWINGS MUST MATCH WITH   AND USED IN STORM WATER QUALITY CALCULATIONS. PLEASE   PROVIDE A COPY OF THESE CALCULATIONS.           PLEASE RESPOND EACH ITEM IN DETAIL TO EXPEDITE YOUR   PERMITTING PROCESS       RASIK CHOKSHI 805-6723 Review Stop ENG ENGINEERING CSD Rev No 1 Status F Date 2008-07-24 Cont ID   Sent By rchokshi Date 2008-07-24 Time 11:08 Rev Time 0.00 Received By rchokshi Date 2008-07-24 Time 11:04 Sent To   Notes 2008-07-24 11:08:18 FAILED FOR FOLLOWING REASONS:       1. PLEASE PROVIDE A COPY OF NOTICE OF INTENT (NOI).   PLEASE APPLY AT FDEP, NPDES STORMWATER SECTION FOR   NOI.   YOU CAN GET NOI INFO FROM   WWW.DEP.STATE.FL.US/WATER/STORMWATER/NPDES/   NOTICE OF INTENT DEP FORM 62-621.300(4)(B),   EFFECTIVE MAY 1, 2003       2. PLEASE SHOW ON DRAWINGS THE SILT FENCE DETAILS &   TURBIDITY DETAILS OFPOLLUTION PREVENTION . PLEASE   SHOW ON DRAWINGS THE SILT FENCE AROUND THE WHOLE SITE,   & TURBIDITY AROUND CATCH BASINS DURING CONSTRUCTION AND   ALL DEMOLITION PHASE.HEIGHT OF FENCE SHOULD BE HIGH   ENOUGH PER FDEP TO STOP DUST PARTICLES.       3. PLEASE PROVIDE A COPY OF BOND FOR ORDINANCE NO.   4060-07:       ALL DEMOLITION AND NEW CONSTRUCTION PERMITS, WITH   EXCEPTION OF SINGLE FAMILY, DUPLEX AND ACCESSORY   APARTMENT, SHALL POST BONDS OR DEPOSITS FOR THE   FOLLOWING:       1. EROSION CONTROL, AND   2. LAND STABILIZATION       THE AMOUNT OF THE EROSION CONTROL AND LAND   STABILIZATION BONDS SHALL BE DETERMINED BY THE ENGINEER   OF RECORD USING THE CURRENT CITY COST SCHEDULE AND   VERIFIED BY THE CITY'S ENGINEERING SERVICES DEPT.   PLEASE CONTACT BRIAN MOREE, ENG SERVICES CONSTRUCTION   SUPERVISOR, AT 561- 494 -1040 FOR MORE INFORMATION.       UPON VERTICAL CONSTRUCTION COMMENCEMENT, PAYMENT IN   FULL OF ALL APPLICABLE FEES, AND COMPLIANCE WITH ALL   TERMS AND CONDITIONS OF ANY POSTED BOND, THE PERMITTEE   MAY REQUEST RELEASE OF THE BONDS OR DEPOSITS.       A COPY OF ORDINANCE NO. 4060-07 MAY BE OBTAINED FROM   THE CITY CLERK'S OFFICE LOCATED ON THE FIRST FLOOR.       4. PLEASE SHOW ON DRAWING ALL CITY STANDARDS NOTES FOR   SIDEWALK, DRIVEWAY, APPROACH, PARKINGS, HANDICAP   PARKINGS, DUMPSTER ENCLOSURE, YOU CAN GET A C D FOR ALL   CITY STANDARDS NOTES FROM 1000, 45 STREET, ENGINEERING   SERVICES, PHONE# 494-1040       5. PLEASE SHOW ON DRAWINGSDUMPSTER & ITS ENCLOSURE   DETAILS PER CITY OF WPB, &LOCATION ON DWG, LOCATION   MUST BE ACCESSIBLE FOR PICKUP TRUCK.       6. PLEASE SHOW ON CALCULATION THAT YOU HAVE CONSIDERED   FLOOD ZONE AREA, & 5,10, 25, 100 YEAR FLOOD CRITERIA   AND CROWN OF THE ROAD WHEN YOU DETERMINE THE FIRST   FLOOR ELEVATION. FIRST FLOOR ELEVATION SHOULD BE   ATLEAST 1 FOOT HIGHER THAN HIGHEST CROWN OF THE ROAD.   STORM WATER CALS APPROVED PER DEAN L'S E-MAILPERMIT#   08050249       7. PLEASE SHOW ON DRAINAGE DRAWINGTHE SITE AREA,   GREEN, LAKE,PARKING AREA, IMPERVIOUS,PERVIOUS AREAYOU   ARE DEVELOPING FOR THIS PROJECT . PLEASEMAKE SURE   THESE AREAS SHOWN ON DRAINAGE DRAWINGS MUST MATCH WITH   AND USED IN STORM WATER QUALITY CALCULATIONS. PLEASE   PROVIDE A COPY OF THESE CALCULATIONS.       8. PLEASE SHOW ALL STORM WATER PIPES AROUND YOUR SITE   SO, WE CANSEE THE LAYOUT OF STORM WATER PIPES FROM   ALL OTHER STORM WATER PIPES. PLEASE SHOW DETAIL OF THE   CONTROL STRUCTURESWITH ELEVATIONS, NOTCHES, BLEEDING   ELEVATION, ETC ON DRAWINGS, CALCULATION FOR   EXFILTRATION TRENCHES, PLEASE SHOW DRY DETENTION/WET   DETENTION AREAS IN STORM WATER CALS IF YOU HAVE ALL   THESE. PLEASE RESUBMIT GEO-TECH REPORT AND ALL   ENVRONMENTAL REPORT.       9. ALSO PLEASE SHOW ALL CATCH BASINS NEAREST,AROUND   YOUR SITE FOR STORM WATER DRAIN SO YOUR SITE DO NOT GET   FLOODED AND HAVE ENOUGH DRAINS.       10. PLEASE PROVIDE A COPY OF SFWMD PERMIT,, GEO-TECH   REPORT&STORM WATER QUALITY CALCULATIONS TO 1000   45TH STREET FOR THEIR APPROVAL BEFORE WE APPROVE.       11. WATER & SEWER PLANS MUST BE APPROVED FROM MANNY G.   OF 1000 45TH STREET BEFORE WE ISSUE A PERMIT.       PLEASE RESPOND EACH ITEM IN DETAIL TO EXPEDITE YOUR   PERMITTING PROCESS       RASIK CHOKSHI805-6723 Review Stop FIRE FIRE DEPARTMENT Rev No 8 Status P Date 2009-05-26 Cont ID   Sent By mawillia Date 2009-05-26 Time 09:31 Rev Time 0.00 Received By mawillia Date 2009-05-26 Time 09:03 Sent To   Notes 2009-05-26 09:12:55 *****REVISIONS, DATED 04/24/09, APPROVED*****           OF THE SUBMITTED NINE REVISED SHEETS, SHEETS E103CR2,   E105CR5, AND E112CR3 WERE STAMPED, INITIALED, AND   DATED.             Review Stop FIRE FIRE DEPARTMENT Rev No 7 Status P Date 2009-04-06 Cont ID   Sent By mawillia Date 2009-04-06 Time 11:09 Rev Time 0.00 Received By mawillia Date 2009-04-06 Time 10:34 Sent To   Notes 2009-04-06 10:44:19 *****REVISIONS, DATED 03/27/09, APPROVED*****           REVISED PLAN SHEETS A103CR4, A106CR3, A118CR5, A901CR5,   E104CR5, AND E105CR4 WERE STAMPED, INITIALED, AND   DATED.                 Review Stop FIRE FIRE DEPARTMENT Rev No 6 Status P Date 2009-04-06 Cont ID   Sent By mawillia Date 2009-04-06 Time 10:33 Rev Time 0.00 Received By mawillia Date 2009-04-06 Time 10:03 Sent To   Notes 2009-04-06 10:33:09 *****SUBMITTAL APPROVED*****           RFI 244 - HORN STROBE MOUNTING ELEVATION IN PUSH WALLS   WAS BLOCK STAMPED. Review Stop FIRE FIRE DEPARTMENT Rev No 5 Status P Date 2009-03-10 Cont ID   Sent By mwennerg Date 2009-03-10 Time 10:33 Rev Time 0.00 Received By mwennerg Date 2009-03-10 Time 10:33 Sent To   Notes 2009-03-10 10:34:43 REVISION #4 DATED 2/24/09 STAMPED SHEET A901CR4. Review Stop FIRE FIRE DEPARTMENT Rev No 4 Status P Date 2009-02-24 Cont ID   Sent By mawillia Date 2009-02-24 Time 14:20 Rev Time 0.00 Received By mawillia Date 2009-02-24 Time 13:35 Sent To   Notes 2009-02-24 13:37:15 *****REVISION #3, DATED 1/18/09, APPROVED*****           PLAN SHEETS A103CR3, A106CR2, A113CR3, AND A118CR3 WERE   STAMPED, INITIALED, AND DATED. Review Stop FIRE FIRE DEPARTMENT Rev No 3 Status P Date 2008-12-17 Cont ID   Sent By mawillia Date 2008-12-17 Time 14:40 Rev Time 0.00 Received By mawillia Date 2008-12-17 Time 14:27 Sent To   Notes 2008-12-17 14:39:56 *****APPROVED*****           PLAN SHEETS A002CR1, A103CR2, A104C, A106CR1, A113CR2 &   A114CR2, A118CR2, A123C, C001CR3, C004CR2, E102CR2,   E111CR2, FP101CR1 THRU FP103CR1, AND FP104C & FP105C   WERE STAMPED, INITIALED, AND DATED. Review Stop FIRE FIRE DEPARTMENT Rev No 2 Status F Date 2008-11-04 Cont ID   Sent By mwennerg Date 2008-11-04 Time 11:17 Rev Time 0.00 Received By mwennerg Date 2008-11-04 Time 11:17 Sent To   Notes 2008-11-04 11:26:51 ***DENIED***       MOST OF THE PREVIOUS COMMENTS HAVE BEEN ADDRESSED.   PLEASE SEE THE FOLLOWING FROM THE PREVIOUS REVIEW FOR   CORRECTION OR FURTHER CLARIFICATION:       1) OK- PLEASE ADD NFPA 101, 2003 TO THE CODE ANALYSIS   ON SHEET A901CR1.       19) OK- PLEASE ILLUSTRATE THE LOCATION OF THE FIRE   DEPARTMENT CONNECTION(S) ON SHEET CO12CR1.       20) PLEASE ILLUSTRATE THE LOCATION OF THE DOUBLE CHECK   DETECTOR ASSEMBLY AND ADD NOTE REGARDING CHAIN AND LOCK   REQUIREMENT IN ADDITION TO ELECTRONIC SUPERVISION.       23) EXIT SIGN IS STILL MISSING ON SHEET E102CR1.       ADDITIONAL NOTE FOR CLARIFICATION:   HOSE STATIONS SHALL BE PROVIDED WITH 2 1/2" - 1 1/2"   CONNECTIONS WITH CHAINS.           MIKE WENNERGREN, ASST. FIRE MARSHAL   FIRE PLAN REVIEW   FIRE PREVENTION (561) 804-4756         Review Stop FIRE FIRE DEPARTMENT Rev No 1 Status F Date 2008-08-08 Cont ID   Sent By mwennerg Date 2008-08-08 Time 10:55 Rev Time 0.00 Received By mwennerg Date 2008-08-08 Time 10:55 Sent To   Notes 2008-08-08 11:24:15 ***DENIED***       1) IN ADDITION TO APPLICABLE BUILDING CODES, LIFE   SAFETY TO COMPLY WITH NFPA 101, 2003.       2) ADDRESS ON BUILDING SHALL BE MINIMUM 6" IN HEIGHT,   1" WIDTH AND CONTRASTING WITH BACKGROUND. PLEASE ADD TO   ELEVATIONS.       3) KNOX BOX TO BE LOCATED AT WHAT IS CONSIDERED TO BE   FRONT ENTRANCE TO BUILDING. CONTACT WPBFR BUREAU OF   FIRE PREVENTION AT (561) 804-4724 FOR ASSISTANCE.       4) PROVIDE PRESCRIPTIVE STRENGTH REQUIREMENTS FOR   HANDRAILS AND GUARDS.       5) EMERGENCY VEHICLE ACCESS AND WATER SUPPLY TO COMPLY   WITH NFPA 1, 2003, CHAPTER-18.       6) ELEVATOR SHALL COMPLY WITH REQUIREMENTS OF ASME   A17.1.       7) FIRE RATED DOORS SHALL BE PROVIDED WITH UL LISTED   DOOR CLOSERS TO CREATE POSITIVE LATCH. DOOR SCHEDULE ON   SHEET A118C.       8) PROVIDE MINIMUM INTERIOR FINISH CLASSIFICATION FOR   WALLS AND CEILING.       9) A FACTOR OF .2" PER PERSON HAS BEEN CALCULATED ON   SHEET A901C FOR STAIRWAYS. PLEASE NOTE THAT TABLE   7.3.3.1 NFPA 101 USES A FACTOR OF 0.2" FOR LEVEL   COMPONENTS AND RAMPS AND 0.3" FOR STAIRWAYS. THIS WILL   HAVE AN OVERALL IMPACT ON CALCULATIONS.       10) PLEASE EXPLAIN FACTOR OF .15 FOR DOOR EGRESS.   PLEASE NOTE LAST COMMENT REGARDING LEVEL COMPONENTS.       11) CONSTRUCTION, ALTERATION AND DEMOLITION TO COMPLY   WITH REQUIREMENTS OF NFPA 241.       12) CLARIFY OCCUPANT CLASSIFICATION FOR EACH AREA.   MODERATE HAZARD IS INDICATED IN CODE ANALYSIS UNDER USE   OF OCCUPANCY. ADDITIONALLY, PLANS INDICATE VARIOUS   PROCESSING AREAS WHICH SEEMS TO SUGGEST INDUSTRIAL   USE.           13) SEPARATE SHOP DRAWINGS AND PERMITS REQUIRED FOR   FIRE SPRINKLER AND FIRE ALARM SYSTEMS.       14) FIRE ALRM SHALL BE UL CERTIFICATED FOR CENTRAL   STATION SERVICE.       15) PENETRATIONS INTO EXIT ENCLOSURES SHALL BE LIMITED   AND IN COMPLIANCE WITH SEC. 7.1.3.2 (6), NFPA 101.   SHEET M102C       16) DUCT SMOKE DETECTORS SHALL INITIATE A GENERAL FIRE   ALARM IN ACCORDANCE WITH LOCAL REQUIREMENTS.       17) NEW FIRE DAMPERS TO BE TESTED FOR CLOSURE IN   ACCORDANCE WITH THE REQUIREMENTS OF UL 555.       18) PROVIDE MANUFACTURER SPECIFICATION SHEETS FOR   PROPOSED FIRE PUMP.       19) KNOX LOCKING CAPS ARE REQUIRED FOR FIRE DEPARTMENT   CONNECTION. SHEET FP 103C       20) PROVIDE DETAIL FOR DOUBLE CHECK DETECTOR ASSEMBLY.   IN ADDITION TO ELECTRONIC SUPERVISION, CONTROL VALVES   TO BE SECURED WITH CHAIN AND LOCK.       21) PROVIDE LOCATION OF AND MANUFACTURER SPECIFICATIONS   FOR GENERATOR.       22) PLEASE SHOW LOCATION OF NEW FIRE HYDRANTS THAT   SHALL BE OPERATIONAL PRIOR TO, DURING AND AFTER   CONSTRUCTION.       23) EXIT SIGN IS MISSING AT EXTERIOR CORRIDOR DOOR   BETWEEN THE LOCKERS AND TOOL/EQUIPMENT ROOM. ELECTRICAL   LIGHTING SHEET       24) FIRE ALARM RISER DOES NOT APPEAR TO ILLUSTRATE   SMOKE DETCTION DEVICES WITH EXCEPTION OF AIR DUCTS.           A RESPONSE LETTER INDICATING HOW AND WHERE ON EACH   SHEET EACH COMMENT WAS ADDRESSED WILL HELP EXPEDITE THE   PLAN REVIEW PROCESS.           MIKE WENNERGREN, ASSISTANT FIRE MARSHAL   FIRE PLAN REVIEW   FIRE PREVENTION (561) 804-4756                                                 Review Stop I INCOMING/PROCESSING Rev No 22 Status N Date 2009-09-22 Cont ID   Sent By lmartine Date 2009-09-16 Time 08:37 Rev Time 0.00 Received By lmartine Date 2009-09-16 Time 08:36 Sent To   Notes 2009-09-22 08:38:45 ELECTRICAL COORDINATION STUDY, GAVE TO DEWEY Review Stop I INCOMING/PROCESSING Rev No 21 Status N Date 2009-08-05 Cont ID   Sent By kstevens Date 2009-08-05 Time 07:45 Rev Time 0.00 Received By kstevens Date 2009-08-05 Time 07:45 Sent To E Notes ***NONE*** Review Stop I INCOMING/PROCESSING Rev No 20 Status N Date 2009-07-10 Cont ID   Sent By lmartine Date 2009-07-10 Time 16:30 Rev Time 0.00 Received By lmartine Date 2009-07-10 Time 16:30 Sent To   Notes 2009-07-10 16:31:08 GAVE TO ROBERT BROWN Review Stop I INCOMING/PROCESSING Rev No 19 Status N Date 2009-07-01 Cont ID   Sent By rmcdouga Date 2009-07-01 Time 08:25 Rev Time 0.00 Received By rmcdouga Date 2009-07-01 Time 08:25 Sent To   Notes 2009-07-01 08:26:38 ELECTRICAL COORDINATION STUDY TO D.PALMER'S DESK Review Stop I INCOMING/PROCESSING Rev No 18 Status N Date 2009-06-16 Cont ID   Sent By lmartine Date 2009-06-16 Time 15:41 Rev Time 0.00 Received By lmartine Date 2009-06-15 Time 15:41 Sent To   Notes 2009-06-16 15:42:42 GAVE TO RON 2009-06-16 15:41:53 MINOR MECHANICAL DUCT REVISIONS Review Stop I INCOMING/PROCESSING Rev No 17 Status N Date 2009-06-11 Cont ID   Sent By rregueir Date 2009-06-11 Time 13:32 Rev Time 0.00 Received By rregueir Date 2009-06-11 Time 13:32 Sent To B Notes 2009-06-11 13:32:30 TO JW DESK - HORIZONTAL SHAFT ASSEMBLY Review Stop I INCOMING/PROCESSING Rev No 16 Status N Date   Cont ID   Sent By   Date 2009-05-12 Time   Rev Time 0.00 Received By jgomez Date 2009-05-12 Time 16:49 Sent To   Notes 2009-05-12 16:49:43 SENT TO C12 Review Stop I INCOMING/PROCESSING Rev No 15 Status N Date 2009-04-29 Cont ID   Sent By dpalmer Date 2009-04-29 Time 12:55 Rev Time 0.00 Received By rregueir Date 2009-04-29 Time 12:55 Sent To B Notes 2009-05-05 10:39:10 PLANS ROUTED TO DOUG WISE FOR EXPEDITED REVIEW 2009-04-29 12:56:13 TO SH Review Stop I INCOMING/PROCESSING Rev No 14 Status N Date 2009-04-17 Cont ID   Sent By swurafti Date 2009-04-17 Time 15:34 Rev Time 0.00 Received By swurafti Date 2009-04-17 Time 15:34 Sent To E Notes 2009-04-17 15:41:27 TO "DPALMER" DESK Review Stop I INCOMING/PROCESSING Rev No 13 Status N Date 2009-04-08 Cont ID   Sent By adarroug Date 2009-04-08 Time 13:03 Rev Time 0.00 Received By adarroug Date 2009-04-08 Time 13:03 Sent To I Notes 2009-04-08 13:04:55 TO "DPALMER" DESK/REV Review Stop I INCOMING/PROCESSING Rev No 12 Status N Date 2009-04-02 Cont ID   Sent By adarroug Date 2009-04-02 Time 14:38 Rev Time 0.00 Received By adarroug Date 2009-04-02 Time 14:38 Sent To   Notes 2009-04-02 14:42:02 TO "C19" Review Stop I INCOMING/PROCESSING Rev No 11 Status N Date 2009-04-02 Cont ID   Sent By adarroug Date 2009-04-02 Time 14:05 Rev Time 0.00 Received By adarroug Date 2009-04-02 Time 14:05 Sent To E Notes 2009-04-02 14:06:15 TO "DPALMER" DESK/SUBMITTAL Review Stop I INCOMING/PROCESSING Rev No 10 Status N Date 2009-04-01 Cont ID   Sent By shill Date 2009-04-01 Time 16:21 Rev Time 0.00 Received By shill Date 2009-04-01 Time 16:21 Sent To   Notes 2009-04-01 16:21:23 BLDG REVISION/SUBMITTAL TO SMH DESK Review Stop I INCOMING/PROCESSING Rev No 9 Status N Date 2009-03-30 Cont ID   Sent By adarroug Date 2009-03-30 Time 16:56 Rev Time 0.00 Received By adarroug Date 2009-03-30 Time 16:56 Sent To B Notes 2009-03-30 16:56:57 TO "SHILL" DESK/SUBMITTAL Review Stop I INCOMING/PROCESSING Rev No 8 Status N Date 2009-03-26 Cont ID   Sent By adarroug Date 2009-03-26 Time 17:00 Rev Time 0.00 Received By adarroug Date 2009-03-26 Time 17:00 Sent To B Notes 2009-03-26 17:00:39 TO "SHILL" DESK/SUBMITTAL Review Stop I INCOMING/PROCESSING Rev No 7 Status N Date 2009-03-24 Cont ID   Sent By rregueir Date 2009-03-24 Time 17:24 Rev Time 0.00 Received By rregueir Date 2009-03-24 Time 17:24 Sent To E Notes 2009-03-24 17:24:32 SENT TO DVP DESK Review Stop I INCOMING/PROCESSING Rev No 6 Status N Date 2009-03-09 Cont ID   Sent By adarroug Date 2009-03-09 Time 11:56 Rev Time 0.00 Received By adarroug Date 2009-03-09 Time 11:56 Sent To   Notes 2009-03-09 11:58:45 TO "COMM" BD#63 Review Stop I INCOMING/PROCESSING Rev No 5 Status N Date 2009-03-09 Cont ID   Sent By adarroug Date 2009-03-09 Time 11:46 Rev Time 0.00 Received By adarroug Date 2009-03-09 Time 11:46 Sent To   Notes 2009-03-09 11:49:00 TO "COMM" BD#10 Review Stop I INCOMING/PROCESSING Rev No 4 Status N Date 2009-02-23 Cont ID   Sent By rregueir Date 2009-02-23 Time 16:28 Rev Time 0.00 Received By rregueir Date 2009-02-23 Time 16:27 Sent To   Notes 2009-02-23 16:27:24 TO COMM BOARD #37 Review Stop I INCOMING/PROCESSING Rev No 3 Status N Date 2008-11-19 Cont ID   Sent By adarroug Date 2008-11-19 Time 16:01 Rev Time 0.00 Received By adarroug Date 2008-11-19 Time 16:01 Sent To   Notes 2008-11-19 16:04:03 TO "COMM" BD#27/PLANS ON RACK/7 ROLLS/3 BOXES--PRIVATE   PROVIDER-- Review Stop I INCOMING/PROCESSING Rev No 2 Status N Date 2008-09-29 Cont ID   Sent By adarroug Date 2008-09-29 Time 08:50 Rev Time 0.00 Received By adarroug Date 2008-09-29 Time 08:50 Sent To   Notes 2008-09-29 08:53:25 TO "COMM" BD#28/PLANS ON RACK Review Stop I INCOMING/PROCESSING Rev No 1 Status   Date 2008-08-08 Cont ID   Sent By rbrown Date 2008-08-08 Time 00:05 Rev Time 0.00 Received By rbrown Date 2008-07-11 Time 10:25 Sent To   Notes 2008-07-11 10:26:04 TO "COMM" BD#22/PLANS ON RACK--PRIVATE PROVIDER-- Review Stop M MECHANICAL (A/C) Rev No 8 Status P Date 2009-08-03 Cont ID   Sent By hmoser Date 2009-08-03 Time 08:26 Rev Time 0.00 Received By hmoser Date 2009-08-03 Time 08:26 Sent To   Notes ***NONE*** Review Stop M MECHANICAL (A/C) Rev No 7 Status P Date 2009-04-14 Cont ID   Sent By rregueir Date 2009-04-14 Time 17:56 Rev Time 0.00 Received By rregueir Date 2009-04-14 Time 17:41 Sent To PC Notes 2009-04-14 17:56:44 REVISED M102CR5 Review Stop M MECHANICAL (A/C) Rev No 6 Status P Date 2009-04-02 Cont ID   Sent By rregueir Date 2009-04-02 Time 19:16 Rev Time 0.00 Received By rregueir Date 2009-04-02 Time 19:16 Sent To   Notes 2009-04-02 19:16:50 REVISED M102CR4 Review Stop M MECHANICAL (A/C) Rev No 5 Status P Date 2009-03-30 Cont ID   Sent By rregueir Date 2009-03-30 Time 17:56 Rev Time 0.00 Received By rregueir Date 2009-03-30 Time 17:46 Sent To PC Notes 2009-03-30 17:55:59 THREE SIGNED/SEALED INSTALLATION DETAILS:       1. WALL PROPELLER FAN   2. OUTSIDE AIR MOTORIZED DAMPER   3. PERLIN ATTACHMENT FOR HANGERS Review Stop M MECHANICAL (A/C) Rev No 4 Status P Date 2009-02-23 Cont ID   Sent By rregueir Date 2009-02-23 Time 19:16 Rev Time 0.00 Received By rregueir Date 2009-02-23 Time 19:15 Sent To   Notes 2009-02-23 19:16:16 REVISED M203CR3. WIND LOAD CALCS FOR APPLIANCES AND   DUCTWORK SUBJECT TO BUILDING (STRUCTURAL) PLAN REVIEW. Review Stop M MECHANICAL (A/C) Rev No 3 Status P Date 2008-12-17 Cont ID   Sent By rregueir Date 2008-12-17 Time 14:56 Rev Time 0.00 Received By rregueir Date 2008-12-16 Time 19:40 Sent To   Notes 2008-12-17 15:18:50 PASSED WITH PROVISO       *********PROVISO**********       PROVIDE MANUFACTURER'S SUBMITTAL DATA SHOWING OUTDOOR   APPLIANCES ARE DESIGNED TO RESIST WIND PRESSURES IN   ACCORDANCE WITH FBCM 301.13. THIS DOCUMENTATION SHALL   BE PROVIDED FOR REVIEW AND APPROVAL PRIOR TO   INSTALLATION AND INSPECTION OF OUTDOOR APPLIANCES.       IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:   RONALD J. REGUEIRO   561.805.6719   [email protected] 2008-12-16 20:49:36         12/16/08: REVIEW IN PROGRESS. PLANS HAVE BEEN REVIEWED   FOR CODE COMPLIANCE AND STAMPED. CORRECTIONS ARE NEEDED   TO ENERGY CALCULATIONS.       THESE CORRECTIONS HAVE BEEN COMMUNICATED TO PERMIT   APPLICANT. REVIEW STATUS WILL BE PASSED ONCE ENERGY   CALCULATIONS HAVE BEEN CORRECTED.       A PROVISO WILL BE ISSUED RELATED TO WIND RESISTANCE OF   ALL OUTDOOR APPLIANCES.         Review Stop M MECHANICAL (A/C) Rev No 2 Status F Date 2008-10-25 Cont ID   Sent By rregueir Date 2008-10-25 Time 14:47 Rev Time 0.00 Received By rregueir Date 2008-10-25 Time 14:46 Sent To   Notes 2008-10-25 14:47:50 REVIEW #: 2ND   ACTION: DENIED       FBC 2004 CODE FAMILY W/ 2007 SUPPLEMENTS   FBC CH.1 AS AMENDED BY THE CITY OF WEST PALM BEACH       THE FOLLOWING COMMENTS ARE NUMBERED TO CORRESPOND WITH   PREVIOUS REVIEW COMMENTS AS WELL AS DESIGNER'S WRITTEN   RESPONSES FOR THE PURPOSE OF CONTINUITY.       1 THROUGH 7: OK       8. CONDENSATE DISCHARGING OUTDOORS IS OK. HOWEVER,   DETAIL 12 ON PAGE M104CR1 SHOWS CONDENSATE TYING INTO   STORM WATER PIPING AT AN ELEVATION LOWER THAN THE STORM   WATER INLET. THIS CONFIGURATION CREATES AN OPENING IN   THE STORM WATER DRAIN WITHIN THE BUILDING. SHOULD THE   STORM WATER DRAIN EVER BACK UP AT A POINT DOWNSTREAM OF   THE CONDENSATE PIPE, THIS WILL CAUSE THE STORM WATER TO   BACKUP INTO THE CONDENSATE PIPE AND MAKE THE CONDENSATE   PIPE A STORM DRAIN PIPE DISCHARGING WITHIN THE   BUILDING. THIS IS NOT AN APPROVED PLACE OF CONDENSATE   DISPOSAL. SEE FBCM 307.2.1 AND THE DEFINITION OF   APPROVED IN SECTION 202 OF FBCM.       9 AND 10: OK       11. PROVIDE PRODUCT APPROVALS AND SUPPORTING   DOCUMENTATION FOR WIND RESISTANCE FOR ALL OUTDOOR   APPLIANCES WHICH ARE EXPOSED TO WIND, INCLUDING EXHAUST   FANS, PACKAGE UNITS AND CONDENSING UNITS. ALL OF THESE   APPLIANCES ARE NOT ONLY REQUIRED TO BE SECURED TO   RESIST WIND PRESSURES, BUT ALSO BE DESIGNED AND   CONSTRUCTED TO RESIST WIND PRESSURES IN ACCORDANCE WITH   FBCM 301.13. ALSO, NO INFORMATION COULD BE FOUND IN   STRUCTURAL PLANS FOR CONSTRUCTION AND SUPPORTS FOR WIND   RESISTANCE RELATED TO EXTERIOR DUCTWORK. PLEASE PROVIDE   MISSING INFORMATION IN ACCORDANCE WITH FBCM 301.13.       12. OK       13. WRITTEN RESPONSE INDICATES A CARRIER HAP REPORT IS   ATTACHED TO THE WRITTEN RESPONSES FOR THE PURPOSE OF   SHOWING COMPLIANCE WITH ASHRAE 62.1-2004. NO SUCH   REPORT COULD BE FOUND ATTACHED TO THE WRITTEN   RESPONSES. PLEASE PROVIDE THE REPORT MENTIONED IN THE   RESPONSE TO DEMONSTRATE COMPLIANCE WITH FBCM 401.1.       14. OK       15. ENERGY CODE COMPLIANCE FORMS HAVE BEEN PROVIDED IN   RESPONSE TO THIS COMMENT. HOWEVER, THERE ARE MULTIPLE   MITSUBISHI SPLIT-SYSTEMS NOT INCLUDED IN THE ENERGY   CODE COMPLIANCE FORM. PLEASE INCLUDE ALL COOLING   APPLIANCES IN THE COMPLIANCE FORM.       IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:   RONALD J. REGUEIRO   561.805.6719   [email protected] Review Stop M MECHANICAL (A/C) Rev No 1 Status F Date 2008-07-29 Cont ID   Sent By rregueir Date 2008-07-29 Time 11:49 Rev Time 0.00 Received By rregueir Date 2008-07-24 Time 16:48 Sent To   Notes 2008-07-29 11:49:27 PRIVATE PROVIDER AUDIT #: 1ST   ACTION: DENIED       FBC 2004 CODE FAMILY W/ 2007 SUPPLEMENTS   FBC CH.1 AS AMENDED BY THE CITY OF WEST PALM BEACH       1. M101C: EF 18 IS SHOWN SERVING STORAGE ROOM 122 WITH   2200 TOTAL CFM OF EXHAUST. HOWEVER, THE FAN SCHEDULE ON   M106C SHOWS EF 18 PROVIDING 3650 CFM OF EXHAUST. WHICH   IS CORRECT? PLEASE COORDINATE FLOOR PLANS AND EQUIPMENT   SCHEDULES SHOWING THE REQUIRED DISTRIBUTION OF AIR IN   ACCORDANCE WITH FBCM 603.1, 501.1 AND FBCB 106.1.1.       2. M101C AND A002C: THE FOLLOWING ROOMS: 124, 125, 126   AND 127 HAVE A ROOF WHICH IS LOWER THAN THE MAIN ROOF   OF THE BUILDING. THIS ROOF HAS MULTIPLE EXHAUST FANS   WHICH ARE REQUIRED TO BE ACCESSIBLE FOR SERVICE AND   REPLACEMENT IN ACCORDANCE WITH FBCM 306.1. ALSO, WHERE   EQUIPMENT AND APPLIANCES REQUIRING ACCESS ARE INSTALLED   ON ROOFS OR ELEVATED STRUCTURES AT A HEIGHT EXCEEDING   16 FEET, SUCH ACCESS SHALL BE PROVIDED BY A PERMANENT   APPROVED MEANS OF ACCESS, THE EXTENT OF WHICH SHALL BE   FROM GRADE OR FLOOR LEVEL TO THE EQUIPMENT AND   APPLIANCES? LEVEL SERVICE SPACE IN ACCORDANCE WITH FBCM   306.5. THIS LOWER ROOF IS SHOWN ON PAGE A002C TO HAVE A   HEIGHT OF 25 FEET ABOVE GRADE. PLEASE SHOW A PERMANENT   MEANS OF ACCESS TO THIS ROOF LEVEL IN ACCORDANCE WITH   THIS SECTION.       3. M102C DETAIL 3: STAIR #1 ENCLOSURE 209 IS SHOWN   BEING PENETRATED BY A 20X16 EXHAUST DUCT FROM EF 30 ON   THE 2ND FLOOR. PENETRATIONS INTO AND OPENINGS THROUGH   AN EXIT ENCLOSURE ARE PROHIBITED EXCEPT FOR REQUIRED   EXIT DOORS, EQUIPMENT AND DUCTWORK NECESSARY FOR   INDEPENDENT PRESSURIZATION, SPRINKLER PIPING,   STANDPIPES, ELECTRICAL RACEWAY FOR FIRE DEPARTMENT   COMMUNICATION AND ELECTRICAL RACEWAY SERVING THE EXIT   ENCLOSURE IN ACCORDANCE WITH FBCB 1019.1.2 AND 1020.5.       4. M102C DETAIL 2: STAIR #1 ENCLOSURE 110 IS SHOWN WITH   MULTIPLE DUCT PENETRATIONS OF THIS EXIT ENCLOSURE/EXIT   PASSAGEWAY ON THE FIRST FLOOR. THIS AREA ALSO SHOWS A   SUPPLY DUCT AND RETURN GRILL SERVING THE EXIT ENCLOSURE   FROM VAV-1. THIS METHOD OF EXIT ENCLOSURE VENTILATION   IS PROHIBITED. IF VENTILATION IS TO BE PROVIDED FOR   THIS ENCLOSURE, IT SHALL BE PROVIDED IN ACCORDANCE WITH   ONE OF THE THREE METHODS LISTED IN ACCORDANCE WITH FBCB   1019.1.3. UNDER ANY OF THESE CONDITIONS, THE EXIT   ENCLOSURE VENTILATION SYSTEM SHALL BE INDEPENDENT OF   OTHER BUILDING VENTILATION SYSTEMS IN ACCORDANCE WITH   THIS SECTION.       5. M102C DETAIL 3: RELIEF AIR DUCT FROM 1ST FLOOR   MECHANICAL ROOM CALLS FOR 24X12 WHILE DETAIL 5 CALLS   FOR THIS SAME DUCT TO BE 20X12. WHICH IS CORRECT?   PLEASE CLARIFY IN ACCORDANCE WITH FBCM 603.1 AND FBCB   106.1.1.       6. M102C DETAIL 1: EF #31 IN CORRIDOR 123 IS PROVIDING   VENTILATION FOR THIS EXIT ENCLOSURE. THERE IS NO   INDICATION ON PLANS WHAT THE SOURCE OF MAKEUP AIR WILL   BE FOR THE 300 CFM OF EXHAUST. MECHANICAL VENTILATION   SHALL BE PROVIDED BY A METHOD OF SUPPLY AIR AND RETURN   OR EXHAUST AIR. THE AMOUNT OF SUPPLY AIR SHALL BE   APPROXIMATELY EQUAL TO THE AMOUNT OF RETURN AND EXHAUST   AIR IN ACCORDANCE WITH FBCM 403.1. ALSO, PLEASE SHOW   THE SOURCE OF SUPPLY OR MAKEUP AIR TO BE IN COMPLIANCE   WITH FBCM 401.4, 401.5 AND 401.6.       7. M102C DETAIL 3: NOTE 17 CALLS FOR EF 30 TO BE   MOUNTED VERTICALLY ON A WALL. THE ONLY INSTALLATION   DETAIL FOUND IN PLANS FOR INLINE FANS IS FOR HORIZONTAL   INSTALLATIONS. PROVIDE DETAIL SHOWING VERTICAL   INSTALLATION, VIBRATION ISOLATION AND SUPPLEMENTAL   RESTRAINT METHODS TO BE USED. EQUIPMENT AND APPLIANCES   SHALL BE INSTALLED AS REQUIRED BY THE TERMS OF THEIR   APPROVAL, IN ACCORDANCE WITH THE CONDITIONS OF THE   LISTING, THE MANUFACTURER?S INSTALLATION INSTRUCTIONS   AND THIS CODE IN ACCORDANCE WITH FBCM 304.1. WHERE   VIBRATION ISOLATION OF EQUIPMENT AND APPLIANCES IS   EMPLOYED, AN APPROVED MEANS OF SUPPLEMENTAL RESTRAINT   SHALL BE USED TO ACCOMPLISH THE SUPPORT AND RESTRAINT   IN ACCORDANCE WITH FBCM 301.10       8. M102C DETAIL 5: MECHANICAL ROOM DETAIL AND   CONDENSATE TRAP DETAIL SHOWS THE CONDENSATE FROM AHU 2   DISCHARGING TO A FLOOR DRAIN. THIS DRAIN IS TIED TO THE   SANITARY SEWER SYSTEM. AIR CONDITIONING CONDENSATE   SHALL NOT DISCHARGE INTO THE SANITARY SEWER SYSTEM IN   ACCORDANCE WITH LOCAL ORDINANCE ARTICLE 3 SECTION   90-125(5). CONDENSATE FROM ALL COOLING COILS AND   EVAPORATORS SHALL BE CONVEYED FROM THE DRAIN PAN OUTLET   TO AN APPROVED PLACE OF DISPOSAL IN ACCORDANCE WITH   FBCM 307.2.1. CONDENSATE SHALL NOT DISCHARGE INTO A   STREET, ALLEY OR OTHER AREAS SO AS TO CAUSE A   NUISANCE.   NOTE: THESE REQUIREMENTS APPLY TO ALL CONDENSATE   DISPOSAL SYSTEMS FROM ALL COOLING COILS. SHOW   COMPLIANCE WITH THESE SECTIONS.       9. M102C DETAIL 2: VAV #1 ON FLOOR PLAN CALLS FOR 355   CFM OF SUPPLY. HOWEVER, EQUIPMENT SCHEDULE ON M106C   CALLS FOR A MAXIMUM CFM OF 225 FOR THE SAME VAV. PLEASE   COORDINATE FLOOR PLANS WITH EQUIPMENT SCHEDULES. AIR   DISTRIBUTION SYSTEMS SHALL BE DESIGNED AND INSTALLED TO   SUPPLY THE REQUIRED DISTRIBUTION OF AIR IN ACCORDANCE   WITH FBCM 603.1.       10. M102C: FLOOR PLAN SHOWS AHU #2 SERVING THE EMPLOYEE   BREAK ROOM AND AHU #2 ALSO SERVING THE ADMIN AREA.   THESE APPLIANCES APPEAR TO BE MISLABELED. THE AHU   SERVING THE ADMIN AREA IS ATTACHED TO ACCU #1 AND THE   AHU SERVING THE EMPLOYEE BREAK AREA IS ACTUALLY A   PACKAGE UNIT. PLEASE COORDINATE FLOOR PLANS AND   EQUIPMENT SCHEDULES, SHOWING ALL APPLIANCES PROPERLY   LABELED IN RELATION TO THE AREAS BEING SERVED IN   ACCORDANCE WITH FBCM 301.1, 304.11 AND FBCB 106.1.1.       11. M104C: ROOF CURB DETAIL HAS NO INFORMATION   REGARDING ATTACHMENT OF CURB TO STRUCTURE OR ATTACHMENT   OF FAN TO ROOF CURB. MECHANICAL EQUIPMENT, APPLIANCES   AND SUPPORTS THAT ARE EXPOSED TO WIND SHALL BE DESIGNED   AND INSTALLED TO RESIST THE WIND PRESSURES ON THE   EQUIPMENT AND THE SUPPORTS AS DETERMINED IN ACCORDANCE   WITH FBCM 301.13. PROVIDE SUFFICIENT DETAIL WITH   SUPPORTING WIND LOAD CALCULATIONS AS NEEDED (FOR   BUILDING PLAN REVIEW) TO SHOW THE INSTALLATION OF ALL   APPLIANCES AND DUCTWORK WHICH IS EXPOSED TO WIND IS   SUFFICIENT TO RESIST ANTICIPATED WIND PRESSURES IN   ACCORDANCE WITH THIS SECTION AND FBCB SECTION 1609.   ALSO PROVIDE SUPPORTING DOCUMENTATION SHOWING OUTDOOR   APPLIANCES THEMSELVES DESIGNED TO RESIST WIND   PRESSURES. THIS INCLUDES ROOFTOP FANS AS WELL AS GROUND   MOUNTED PACKAGE UNITS AND CONDENSING UNITS.       12. M105C: THE RELIEF AIR DUCT WHICH IS SHOWN   DISCHARGING ONTO THE RECYCLING FLOOR IS ALSO SHOWN   ATTACHED TO THE RETURN AIR PLENUM OF AHU #1. ACCORDING   TO THE SEQUENCE, DAMPERS ARE TO MODULATE BASED ON THE   PRESSURE IN THE CONDITIONED SPACE TO ALLOW RELIEF AIR   TO BE DISCHARGED. HOWEVER, THE RETURN AIR PLENUM WILL   BE UNDER A CONSTANT NEGATIVE PRESSURE. THIS DESIGN WILL   CAUSE THE RELIEF AIR DUCT TO ACT AS AN INTAKE DUCT,   DRAWING AIR FROM THE RECYCLING FLOOR INTO THE ADMIN   AREA. THIS DESIGN IS NOT IN COMPLIANCE WITH FBCM   401.5.1, 403.2.1(1) AND FBCM 603.1. PLEASE SHOW A   DESIGN WHICH IS CAPABLE OF ACHIEVING THE DESIGN INTENT   AS DESCRIBED IN THE RELIEF AIR SEQUENCE OF OPERATIONS.   ALSO, THE RELIEF AIR SEQUENCE CALLS FOR 3 DIFFERENT   MODULATING DAMPERS TO BE OPENED IN STAGES. FLOOR PLANS   AND CONTROL DIAGRAM ONLY SHOW ONE MOTORIZED DAMPER ON   THE RELIEF AIR SYSTEM. PLEASE CLARIFY.       13. OUTSIDE AIR: NO INFORMATION REGARDING THE REQUIRED   RATES OF OUTSIDE AIR HAS BEEN PROVIDED. PLEASE PROVIDE   OUTSIDE AIR CALCULATIONS SHOWING THE VENTILATION METHOD   USED, SUCH AS FBCM TABLE 403.3, THE VENTILATION RATE   METHOD OF AHSRAE 62.1-2004 OR THE IAQ METHOD OF ASHRAE   62.1-2004 AS ALLOWED UNDER FBCM 403.4. PROVIDE   SUPPORTING DOCUMENTATION AND/OR CALCULATIONS   APPROPRIATE FOR THE METHOD USED IN ACCORDANCE WITH FBCM   401.1. IT IS ACKNOWLEDGED THAT CO2 CONTROLS ARE SHOWN   ON THE VAV SEQUENCE, BUT THE REQUIRED RATES OF   VENTILATION FOR THE SPACES BEING SERVED ARE NOT   PROVIDED ON PLANS. ALSO, THE EMPLOYEE BREAK ROOM IS NOT   SERVED BY A VAV SYSTEM AND IS THEREFORE NOT ACCOUNTED   FOR IN THIS SEQUENCE.       14. REHEAT: THE CO2 CONTROL SEQUENCE CALLS FOR ELECTRIC   REHEAT OF VAV SYSTEMS WHEN OUTSIDE AIR IS REQUIRED TO   PREVENT OVER-COOLING. REHEATING OR THE SIMULTANEOUS   OPERATION OF THE HEATING AND COOLING SYSTEMS TO THE   SAME ZONE ARE PROHIBITED IN ACCORDANCE WITH FBCB   13-407.1.ABC.2.1.1. IF REHEAT IS TO BE USED, PLEASE   PROVIDE DOCUMENTATION SHOWING AT LEAST ONE OF THE   EXCEPTIONS UNDER THIS SECTION HAS BEEN SATISFIED.       15. ENERGY: ENERGY CALCULATIONS WERE NOT PROVIDED WITH   THIS APPLICATION FOR PERMIT. PROVIDE A COMPLETED ENERGY   CODE COMPLIANCE FORM IN ACCORDANCE WITH FBCM 301.2 AND   FBCB 13-101.1.1. ALSO, COOLING LOAD CALCULATIONS SHALL   BE APPENDED TO THE ENERGY CODE COMPLIANCE FORM IN   ACCORDANCE WITH FBCB 13-407.1.ABC.1. AUDIT FOR   COMPLIANCE WITH THE REQUIREMENTS OF FBCB CHAPTER 13 CAN   NOT BE PERFORMED AT THIS TIME.       16. THIS PERMIT APPLICATION WAS SUBMITED UNDER THE   PRIVATE PROVIDER PROVISIONS OF FS 553.791. AS SUCH THE   FOLLOWING REQUIREMENTS HAVE NOT BEEN SATISFIED:   A) A NOTICE TO BUILDING OFFICIAL HAS NOT BEEN PROVIDED   AS REQUIRED UNDER FS 553.791(4).   B) PLANS FOR THE "SORT ENCLOSURE" AIR CONDITIONING   SYSTEMS HAVE BEEN SUBMITTED AS SHOP DRAWINGS, BUT THEY   ARE ACTUALLY SIGNED AND SEALED PLANS BY THE DESIGNER OF   RECORD FOR THIS PROJECT. EITHER WAY, THESE PLANS WERE   NOT STAMPED AS REVIEWED AND NO AFFIDAVIT WAS PROVIDED   FOR THESE PLANS BY THE PRIVATE PROVIDER AS REQUIRED   UNDER FS 553.791(6). THESE PLANS WILL NOT BE AUDITED   PRIOR TO REVIEW AND SUBMISSION OF AFFIDAVIT BY THE   PRIVATE PROVIDER.       PLEASE RESPOND TO EACH COMMENT IN WRITING WITH A   DETAILED EXPLANATION OF HOW EACH COMMENT HAS BEEN   ADDRESSED AS WELL AS WHERE THE SUPPORTING INFORMATION   CAN BE FOUND. ALSO, PLEASE RETURN ONE OLD/VOIDED SET OF   PLANS FOR REFERENCE. THESE STEPS WILL ASSIST IN A   TIMELY AUDIT OF RESUBMITTED PLANS.       IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:   RONALD J. REGUEIRO   561.805.6719   [email protected] Review Stop P PLUMBING Rev No 2 Status P Date 2008-10-07 Cont ID   Sent By kstevens Date 2008-10-07 Time 09:56 Rev Time 0.00 Received By kstevens Date 2008-10-06 Time 14:27 Sent To   Notes ***NONE*** Review Stop P PLUMBING Rev No 1 Status F Date 2008-07-16 Cont ID   Sent By kstevens Date 2008-07-16 Time 16:05 Rev Time 0.00 Received By kstevens Date 2008-07-16 Time 16:05 Sent To   Notes 2008-07-16 16:44:41 AUDIT DENIED   REFERENCE: FBC-2004 PLUMBING   FBC-2004 CHAPTER 1   FBC-2004 CHAPTER 11   FLORIDA ADMINISTRATIVE CODE   FLORIDA STATUTES       1. PLEASE SUBMIT AFFIDAVITS AS REQUIRED IN FS 553.791   FOR EACH DISCIPLINE.       2. SHT A101C MEN'S AND WOMEN'S TOILET AREAS ARE   INDICATED BY DETAIL 1/A101 - A111 - A112. SHTS A101,   A111 & A112 NOT SUBMITTED. PLEASE CORRELATE. SECTIONS   106.1.1 & 106.1.3. THIS IS INDICATED IN MANY AREAS WITH   MANY DETAILS AND MANY SHEETS WHERE THE DETAILS DO NOT   CORRELATE WITH SHEETS SUBMITTED.       3. SHT A105C DETAIL 7 SHOW THE CLEAR FLOOR SPACE FOR   ACCESSIBLE W/C & LAV. SECTIONS 11-4.16.2 & 11-4.19.3.       4. SHT A105C DETAILS 8 C & D. SHOW CLEARANCES AND   INDICATE FAUCET TYPES PER SECTIONS 11-4.19.2 &   11-4.19.5.       5. SHT A111C DETAILS 1, 2, 3 & 4 SHOW THE CLEAR FLOOR   SPACE FOR ACCESSIBLE W/C'S, LAVS, URINALS & DRINKING   FOUNTAINS PER SECTIONS 11-4.15.5(1), 11-4.16.2,   11-4.18.3 & 11-4.19.3.       6. SHT A112C DETAILS 14 & 17 INDICATE THE FAUCET TYPE   PER SECTIONS 11-4.19.5 & 11-4.24.7.       7. SHT A112C DETAIL 17 SHOW SINK DEPTH PER SECTION   11-4.24.4. (SHOWS 12" - MAX 6-1/2").       8. MINIMUM 3 SETS OF PLANS REQUIRED TO BE SUBMITTED PER   SECTION 106.1. ONLY ONE SET OF ARCHITECTURAL,   STRUCTURAL, LANDSCAPE, IRRIGATION, PLUMBING, ELECTRIC &   MECHANICAL. SUBMITTED.       9. ALL SHEETS SUBMITTED HAVE NOT BEEN REVIEWED AND   SIGNED OFF BY THE PRIVATE PROVIDER. SECTION   553.791(1)(H)(I). (SEE LANDSCAPE, IRRIGATION & FIRE   PROTECTION).       WHEN RESUBMITTING PLANS PLEASE INDICATE   THE REVISION & REMOVE & REPLACE ANY   PAGES AS NECESSARY. A TRANSMITTAL LETTER   LISTING THE ORIGINAL REVIEW COMMENT NUMBER,   WITH A DESCRIPTION OF THE REVISION MADE,   IDENTIFYING THE SHEET OR SPECIFICATION   PAGE WHERE THE CHANGES CAN BE FOUND   WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE   ALL VOID SHEETS FROM ALL PLANS AND PLACE   ONE SET OF THEM LOOSELY ON TOP OF THE   COLLATED PLANS TO BE REVIEWED.   THANK YOU FOR YOUR ANTICIPATED COOPERATION.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected] Review Stop Z ZONING Rev No 2 Status P Date 2008-10-07 Cont ID   Sent By kdfreema Date 2008-10-07 Time 14:47 Rev Time 0.00 Received By kdfreema Date 2008-10-07 Time 14:47 Sent To   Notes ***NONE*** Review Stop Z ZONING Rev No 1 Status P Date 2008-07-30 Cont ID   Sent By kdfreema Date 2008-07-30 Time 13:34 Rev Time 0.00 Received By kdfreema Date 2008-07-30 Time 13:34 Sent To   Notes ***NONE*** Account Summary | Usage Policy | Privacy Policy Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved