| 2008-04-09 13:21:39 | ****CORRECTIONS**** |
| | SAMANTHA HILL, BUILDING PLANS EXAMINER |
| | 561-805-6724 [email protected] |
| | |
| | FBCFLORIDA BUILDING CODE 2004 |
| | FBC EBFLORIDA BUILDING CODE 2004 |
| | EXISTING BUILDING CODE |
| | FBC*CITY OF WEST PALM BEACH |
| | AMENDMENTS TO THE FBC2004 |
| | |
| | ROOFING PERMIT; ONLY CHECKED ITEMS APPLY |
| | |
| | ____1.)EFFECTIVE OCTOBER 1, 2007, SECONDARY WATER |
| | BARRIER REQUIRED FS553.844(5)(A). PROVIDE |
| | INFORMATION (PRODUCT APPROVAL OR SPECIFICATIONS) TO |
| | SHOW HOW YOU WILL COMPLY WITH THIS REQUIREMENT. |
| | INFORMATION IS AVAILABLE AT WWW.BOAF.NET, HURRICANE |
| | MITIGATION. |
| | |
| | ____2.)CONTRACTOR IS TO PROVIDE THE FOLLOWING |
| | INFORMATION ON THE APPLICATION, SEE ATTACHED POLICY; |
| | MEAN ROOF HEIGHT, ROOF PITCH, ROOF DECK TYPE, AREA OF |
| | EACH ROOF TYPE |
| | |
| | ____3.)FLORIDA STATE OR LOCAL PRODUCT APPROVAL |
| | REQUIRED IN ADDITION TO THE EVALUATION REPORT |
| | SUBMITTED, FAC9B72.WWW.FLORIDABUILDING.ORG |
| | |
| | ____4.)FOR THE FLAT ROOF, SELECT THE APPROVED |
| | ASSEMBLY YOU ARE USING.ALSO INDICATE WHICH FASTENER |
| | YOU ARE USING IF THE OPTIONS HAVE DIFFERENT PRESSURE |
| | LIMITATIONS. |
| | |
| | _XX_5.)FOR THE FLAT ROOF, SPECIFY THE ENHANCED |
| | FASTENING FOR CORNER AND PERIMETER ZONES.THIS IS TO |
| | BE EITHER WRITTEN ON THE PRODUCT APPROVAL OR SUBMITTED |
| | ON LETTERHEAD, TWO SETS (NOT WRITTEN ON THE RESUB |
| | SHEET). |
| | |
| | GRAPHICS AND LANGUAGE WERE PROVIDED, BUT ARE CONFUSING. |
| | IT APPEARS THAT THE CONTRACTOR HAS DRAWN A SHEET OF 4X8 |
| | INSULATION, THEN DRAWN FASTENERS ALONG THE EDGE AS IF |
| | IT WERE BEING FASTENED LIKE A BASE SHEET BUT REFERED TO |
| | ZONES AS THE DRAWING WAS A ROOF.FOR INSTANCE, THE |
| | CORNER OF THE INSULATION BOARD IS SHOWN AS HAVING 4INCH |
| | SPACING ON FASTENERS, EDGE HAVING 6INCH AND IT REFERS |
| | TO THESE AREAS AS "CORNERS" AND "PERIMETERS".YOU ARE |
| | CONFUSING THREE DIFFERENT SCENARIOS/CONDITIONS; BASE |
| | SHEET FASTENING, INSULATION BOARD FASTENING, AND ROOF |
| | COMPONENT AND CLADDING ZONE, AND HAVE COMBINED THEM TO |
| | SUBMIT A CONVOLUTED FASTENING PATTERN WHICH CANNOT BE |
| | IMPLEMENTED IN THE FIELD. |
| | |
| | THE LANGUAGE ON THE ASSEMBLY STATES THAT THERE WILL BE |
| | 72 FASTENERS PER BOARD.PLEASE INDICATE WHICH OF THE |
| | FASTENING OPTIONS YOU ARE USING (THERE ARE THREE |
| | DIFFERENT ONES FOR THIS ASSEMBLY), AND NOTE THAT THE |
| | INSULATION GETS FASTENED THROUGH THE BASE SHEET BUT THE |
| | FASTENING IS DETERMINED BY THE EDGE OF THE BASE SHEET, |
| | NOT THE EDGE OF THE INSULATION.PLEASE DISCARD THE |
| | PLAN OF FASTENING AND PROVIDE LANGUAGE CONSISTENT WITH |
| | THE PRODUCT APPROVAL - STATE FASTENER SPACING, NUMBER |
| | OF ROWS.PLEASE BE CLEAR AS TO WHETHER OR NOT THE |
| | NUMBER OF ROWS INCLUDES THE LAP ROW OR IF THE NUMBER OF |
| | ROWS SPECIFIED ARE FOR THE FIELD ROWS. |
| | |
| | PLEASE HAVE THE QUALIFIER FOR THE COMPANY REVIEW THE |
| | ENHANCED FASTENING PATTERN BEFORE RESUBMITTAL. |
| | |
| | TWO COMPLETE COLLATED SETS OF PERMIT DOCUMENTS REQUIRED |
| | FOR ISSUANCE. |
| | |
| | ____ 6.)ON THE TILE PRODUCT APPROVAL, INDICATE WHICH |
| | METHOD OF ATTACHMENT YOU ARE USING.IF YOU SELECT FOAM |
| | ADHESIVE, PRODUCT APPROVALS REQUIRED FAC9B72. |
| | |
| | ____ 7.)SEE PRODUCT LIMITATION #7.CALCULATIONS |
| | PREPARED BY AN ARCHITECT, ENGINEER, OR REGISTERED ROOF |
| | CONSULTANT REQUIRED FOR ENHANCED FASTENING. |
| | |
