City of West Palm Beach eGovPlus

Plan Review Details - Permit 07080572

Plan Review Stops For Permit 07080572

Review Stop	AD			ADDRESSING
Rev No	2	Status	P	Date	2007-10-16			Cont ID
Sent By	lursu			Date	2007-10-16	Time	14:47	Rev Time	0.00
Received By	lursu			Date	2007-10-16	Time	14:47	Sent To

Notes

2007-10-16 14:50:44	THE RECORDED UNITY OF TITLE FOR THESE TWO PARCELS WAS
	RECEIVED AND A NEW SITE ADDRESS : 2671 DAKOTA CIR ,WEST
	PALM BEACH, FL 33409 IS ASSIGNED TO THE NEW SINGLE
	HOUSE.BASED ON THE UOT A NEW PARCEL CONTROL NUMBER WILL
	BE ISSUED BY THE PROPERTY APPRAISER'S OFFICE .

	LACRAMIOARA URSU
	MIS - GIS SUPPORT SPECIALIST
	CITY OF WEST PALM BEACH
	OFFICE:822-1239
	FAX: 822-1249
	E-MAIL:[email protected]

Review Stop	AD			ADDRESSING
Rev No	1	Status	F	Date	2007-08-31			Cont ID
Sent By	lursu			Date	2007-08-31	Time	11:27	Rev Time	0.00
Received By	lursu			Date	2007-08-31	Time	11:27	Sent To

Notes

2007-08-31 11:36:08	PRIOR OF ISSUING THE NEW SITE ADDRESS FOR THE NEW HOUSE
	, THE UNITY OF TITLE FOR THE TWO PARCELS MUST BE
	RECORDED .THE PROPERTY APPRAISER'S OFFICE WILL ISSUE A
	NEW PARCEL CONTROL NUMBER FOR THE UNIFIED PROPERTIES
	AND BASED ON THE NEW PCN, THE CITY WILL ISSUE THE NEW
	SITE ADDRESS.

	LACRAMIOARA URSU
	MIS - GIS SUPPORT SPECIALIST
	CITY OF WEST PALM BEACH
	OFFICE:822-1239
	FAX: 822-1249
	E-MAIL:[email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	8	Status	P	Date	2009-04-30			Cont ID
Sent By	rmcdouga			Date	2009-04-30	Time	08:37	Rev Time	0.00
Received By	rmcdouga			Date	2009-04-30	Time	08:37	Sent To

Notes

2009-04-30 09:32:26	REVISION TO REPLACE GARAGE SIDE DOOR WITH ONE OF A KIND
	SITE SPECIFIC DOOR IS OK.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	7	Status	F	Date	2009-04-15			Cont ID
Sent By	rmcdouga			Date	2009-04-15	Time	10:04	Rev Time	0.00
Received By	rmcdouga			Date	2009-04-15	Time	10:04	Sent To

Notes

2009-04-15 10:41:03	REVISION DENIED BY BUILDING


	1) THE REVISION TO CHANGE FRONT DOOR IS OK. FL. PRODUCT
	APPROVALS WERE SUBMITTED. PLACE COPY OF STAMPED PRODUCT
	APPROVAL WITH THE PLANS.

	2) THE REVISION TO CHANGE SIDE DOOR IS DENIED. THIS
	DOOR DOES NOT HAVE STATE PRODUCT APPROVAL. LOCAL/SITE
	SPECIFIC ENGINEERING IS REQUIRED IN ACCORDANCE WITH DCA
	RULE 9B-72. ORIGINAL SIGNED AND SEALED DOCUMENTS FROM
	THE ENGINEER ARE REQUIRED. NOTE: THE DESIGN PRESSURES
	IN THE SUBMITTAL OF +36.0 PSF, -39.3 PSF ARE TOO LOW.
	THE STRUCTURE IS LOCATED IN EXPOSURE CATEGORY C THE
	OPENING PRESSURE OF +47.5 PSF, -51.8 PSF ARE SPECIFIED
	ON SHEET S3.02 OF THE PLANS FOR A 20 SQFT OPENING. THE
	STREET NAME ON THE LETTER IS INCORRECT, IT IS DAKOTA
	CIRCLE. PLEASE CORRECT.

	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	6	Status	P	Date	2008-02-11			Cont ID
Sent By	rmcdouga			Date	2008-02-11	Time	11:05	Rev Time	0.00
Received By	rmcdouga			Date	2008-02-11	Time	11:05	Sent To

Notes

2008-02-11 11:07:15	CONTRACTOR SUBMITTED PRODUCT APPROVAL FOR GARAGE DOORS
	WITH ADEQUATE DESIGN PRESSURES AS REQUESTED IN THE
	BUILDING PROVISO.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	5	Status	P	Date	2008-01-31			Cont ID
Sent By	rmcdouga			Date	2008-01-31	Time	15:38	Rev Time	0.00
Received By	rmcdouga			Date	2008-01-31	Time	07:01	Sent To

Notes

2008-01-31 15:38:42
	BUILDING PROVISO

	SUBMIT PRODUCT APPROVALS FOR THE 9' X 8' OVERHEAD
	GARAGE DOORS WITH DESIGN PRESSURES GREATER THAN + 43.7
	/ -49.5 PSF.

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	4	Status	F	Date	2008-01-17			Cont ID
Sent By	rmcdouga			Date	2008-01-17	Time	11:29	Rev Time	0.00
Received By	rmcdouga			Date	2008-01-16	Time	11:27	Sent To

Notes

2008-01-17 11:41:10	2004 FBC W/2007 SUPPLEMENTS
	NSFR

	DENIED BY BUILDING

	1) COMPLIED

	2) A RECORDED COPY OF THE NOTICE OF COMMENCEMENT
	MUST BE SUBMITTED BEFORE A
	PERMIT CAN BE ISSUED. WORK MUST COMMENCE WITHIN 90 DAYS
	OF THE DATE THE NOC IS RECORDED. FS 713.13. THE ONE
	THAT WAS SUBMITTED IS EXPIRED.

	3) IMPACT FEES MUST BE PAID TO PALM
	BEACH COUNTY, PLANS STAMPED BY THEM AND
	COPY OF RECEIPT SUBMITTED TO CITY OF
	WEST PALM BEACH BUILDING DEPARTMENT,
	BEFORE A BUILDING PERMIT CAN BE ISSUED. SUBMIT COPY OF
	THE PAID RECEIPT FOR THE IMPACT FEES.

	4) COMPLIED

	5)COMPLIED

	6) COMPLIED

	7) COMPLIED

	8) COMPLIED

	9)NOTE THAT THE DEFINITION FOR EXPOSURE C HAS CHANGED
	EFFECTIVE DECEMBER 8, 2006 (2006 AMENDMENTS TO THE
	FBC), FBC1609.4, FBC R301.2.1.4.
	EXPOSURE C. OPEN TERRAIN WITH SCATTERED
	OBSTRUCTIONS, INCLUDING SURFACE UNDULATIONS OR OTHER
	IRREGULARITIES, HAVING HEIGHTS GENERALLY LESS THAN 30
	FEET (9144 MM) EXTENDING MORE THAN 1,500 FEET (457.2 M)
	FROM THE BUILDING SITE IN ANY QUADRANT. THIS EXPOSURE
	SHALL ALSO APPLY TO ANY BUILDING LOCATED WITHIN
	EXPOSURE B-TYPE TERRAIN WHERE THE BUILDING IS DIRECTLY
	ADJACENT TO OPEN AREAS OF EXPOSURE C-TYPE TERRAIN IN
	ANY QUADRANT FOR A DISTANCE OF MORE THAN 600 FEET
	(182.9 M). THE STRUCTURE IS LOCATED ADJACENT TO A GOLF
	COURSE WHICH MAY REQUIRE IT TO BE DESIGNED AS EXPOSURE
	C. PLEASE REVISE PLANS OR INDICATE WHY THE EXPOSURE
	CATEGORY SHOULD NOT BE CHANGED. ADDITIONAL COMMENTS:
	THE INFORMATION THAT WAS SUBMITTED DOES NOT CONSIDER
	THE TERRAIN IN THE ENTIRE REAR QUADRANT, WHICH INCLUDES
	THE TERRAIN FOR 45 DEGREES EITHER SIDE OF THE WIND
	DIRECTION BEING CONSIDERED. SEE ASCE 7-02 SECTION
	6.5.6.1. ALSO SEE ATTACHED COPIES OF THE 2004 FBC
	RESIDENTIAL CODE COMMENTARY AND ASCE 7-02.

	10) COMPLIED

	11) COMPLIED

	12) COMPLIED

	13) COMPLIED

	14) COMPLIED

	15) COMPLIED

	16) COMPLIED

	17)COMPLIED

	18) COMPLIED

	19) COMPLIED

	20) COMPLIED

	21) COMPLIED

	22)COMPLIED

	23) COMPLIED

	24) COMPLIED

	25) REVISE COMPONENT AND CLADDING PRESSURES TO EXPOSURE
	CATEGORY 'C'. SEE ITEM #9.

	26) COMPLIED

	27) COMPLIED

	28) COMPLIED

	29) COMPLIED

	30) N/A

	31) COMPLIED

	32) COMPLIED

	33) COMPLIED

	34) CORRECTED

	35) COMPLIED

	36) COMPLIED

	37) COMPLIED

	38) COMPLIED

	39) CORRECTED

	40) COMPLIED

	41) COMPLIED

	42)COMPLIED

	43)COMPLIED

	44) COMPLIED

	45) CORRECTED

	46) COMPLIED

	47)COMPLIED

	48) COMPLIED

	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714
	[email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	3	Status	F	Date	2007-12-20			Cont ID
Sent By	rmcdouga			Date	2007-12-20	Time	13:10	Rev Time	0.00
Received By	rmcdouga			Date	2007-12-19	Time	07:22	Sent To

Notes

2007-12-20 13:10:30	2004 FBC W/2007 SUPPLEMENTS
	NSFR

	DENIED BY BUILDING

	1) COMPLIED

	2) A RECORDED COPY OF THE NOTICE OF COMMENCEMENT
	MUST BE SUBMITTED BEFORE A
	PERMIT CAN BE ISSUED. WORK MUST COMMENCE WITHIN 90 DAYS
	OF THE DATE THE NOC IS RECORDED. FS 713.13.

	3) IMPACT FEES MUST BE PAID TO PALM
	BEACH COUNTY, PLANS STAMPED BY THEM AND
	COPY OF RECEIPT SUBMITTED TO CITY OF
	WEST PALM BEACH BUILDING DEPARTMENT,
	BEFORE A BUILDING PERMIT CAN BE ISSUED.

	4) COMPLIED

	5)FBC R401.4AREA OF QUESTIONABLE
	SOIL.SUBMIT A GEOTECHNICAL REPORT
	TO VERIFY THE SAFE BEARING CAPACITY OF
	THE SOIL. SUBMIT 2 SIGNED AND SEALED COPIES.

	6) COMPLIED

	7) THE FLOOD ZONE DESIGNATION ON THE SURVEY IS
	SPECIFIED AS A8, WHICH IS INCORRECT. THIS AREA IS
	INCLUDED IN THE LETTER OF MAP REVISION (LOMR) FOR THE
	VILLAGES OF PALM BEACH LAKES AND SPENCER LAKES PLATS
	1,2 AND 3 DATED DECEMBER 3, 1983. PLEASE CORRECT.
	SUBMIT REVISED SURVEY.

	8) THE ENERGY CALCULATIONS LIST THE CONDITIONED FLOOR
	AREA AS 8000 SQFT AND THE PLANS SPECIFY 8327 SQFT.
	PLEASE CORRECT. FBC R CHAPTER 11 AND FBC CHAPTER 13.
	THE NEW FORMS HAVE NOT BEEN SIGNED BY THE OWNER/AGENT
	AS REQUIRED BY FBC 13-600.

	9)NOTE THAT THE DEFINITION FOR EXPOSURE C HAS CHANGED
	EFFECTIVE DECEMBER 8, 2006 (2006 AMENDMENTS TO THE
	FBC), FBC1609.4, FBC R301.2.1.4.
	EXPOSURE C. OPEN TERRAIN WITH SCATTERED
	OBSTRUCTIONS, INCLUDING SURFACE UNDULATIONS OR OTHER
	IRREGULARITIES, HAVING HEIGHTS GENERALLY LESS THAN 30
	FEET (9144 MM) EXTENDING MORE THAN 1,500 FEET (457.2 M)
	FROM THE BUILDING SITE IN ANY QUADRANT. THIS EXPOSURE
	SHALL ALSO APPLY TO ANY BUILDING LOCATED WITHIN
	EXPOSURE B-TYPE TERRAIN WHERE THE BUILDING IS DIRECTLY
	ADJACENT TO OPEN AREAS OF EXPOSURE C-TYPE TERRAIN IN
	ANY QUADRANT FOR A DISTANCE OF MORE THAN 600 FEET
	(182.9 M). THE STRUCTURE IS LOCATED ADJACENT TO A GOLF
	COURSE WHICH MAY REQUIRE IT TO BE DESIGNED AS EXPOSURE
	C. PLEASE REVISE PLANS OR INDICATE WHY THE EXPOSURE
	CATEGORY SHOULD NOT BE CHANGED. NOTE: ALTHOUGH THE
	GENERAL NOTES (C) (3) ON A.09 HAVE BEEN REVISED TO
	EXPOSURE CATEGORY 'C', THE COMPONENT AND CLADDING
	PRESSURES IN THE TABLE ON S3.02 HAVE NOT BEEN REVISED
	TO CATEGORY 'C'. PLEASE CORRECT.

	10) THE WALLS OF THE WINE ROOM ARE REQUIRED TO BE
	WATERPROOFED IN ACCORDANCE WITH FBC R406. INDICATE HOW
	THIS WILL BE ACCOMPLISHED ON THE PLANS. THE SPRAY FOAM
	INSULATION DOES NOT COMPLY WITH THE REQUIREMENTS OF FBC
	R406.

	11) COMPLIED

	12) COMPLIED

	13) COMPLIED

	14) COMPLIED

	15) COMPLIED

	16) COMPLIED

	17)COMPLIED

	18) COMPLIED

	19) COMPLIED

	20) COMPLIED

	21) COMPLIED

	22)COMPLIED

	23) COMPLIED

	24) COMPLIED

	25) REVISE COMPONENT AND CLADDING PRESSURES TO EXPOSURE
	CATEGORY 'C'. SEE ITEM #9.

	26) COMPLIED

	27) COMPLIED

	28) COMPLIED

	29) THE SIMPSON H10 OR USP RT16 "R" IN SCHEDULE ON
	S2.02) WILL NOT WORK FOR ATTACHING THE FLOOR TRUSSES TO
	THE LEDGERS. THE FLOOR TRUSSES ARE 3-1/2" WIDE AND THE
	CONNECTORS HAVE A 1-9/16" OPENING FOR THE TRUSS. PLEASE
	CORRECT.

	30) N/A

	31) COMPLIED

	32) COMPLIED

	33) COMPLIED

	34) CORRECTED

	35) THE TRUSS LAYOUT IS REQUIRED TO BE REVIEWED AND
	APPROVED IN WRITING BY THE DESIGNER OF RECORD FOR THE
	STRUCTURE. SEE R802.1.6, FBC106.1.1.2* CITY AMENDMENTS
	AND FAC 61G15-31.003.

	36) THE ROOF TRUSSES ARE REQUIRED TO HAVE A MINIMUM
	BOTTOM CORD LIVE LOAD OF 10 PSF. SEE TABLE R301.5.
	PLEASE CORRECT.

	37) THE TRUSS DRAWING SUBMITTAL DOES NOT MEET THE
	REQUIREMENTS OF FAC 61G-15-31.003. PLEASE SEPARATE THE
	DRAWINGS AND PLACE THEM WITH THE APPROPRIATE COVER
	SHEETS AND NUMBER THE DRAWINGS TO CORRESPOND TO THE
	NUMBERING ON THE COVERSHEETS. SEE ATTACHMENT.

	38) COMPLIED

	39)CORRECTED

	40) FBC 106.3* CITY AMENDMENTS PRODUCT
	APPROVALS. THOSE PRODUCT WHICH ARE
	REGULATED BY DCA RULE 9B-72 SHALL BE
	REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD PRIOR TO SUBMITTAL
	FOR JURISDICTIONAL APPROVAL.

	41) COMPLIED

	42)THE GENERIC PRESSURES IN THE SCHEDULE ON S3.02 MAY
	BE TOO HIGH FOR THE GARAGE DOORS WHEN THEY ARE
	INCREASED TO EXPOSURE 'C'. SEE TABLE R301.2(4). PLEASE
	INDICATE THE REQUIRED OPENING PRESSURES FOR THE GARAGE
	DOORS ON THE PLANS.

	43)COMPLIED

	44) COMPLIED. HOWEVER, PLEASE CLARIFY WHICH WINDOWS THE
	PRODUCT APPROVALS FOR THE WEATHER SHIELD "LEGACY" FIXED
	CASEMENT WINDOWS ARE FOR. THERE DOES NOT TO BE ANY OF
	THESE SPECIFIED ON THE PLANS.

	45) CORRECTED

	46) COMPLIED

	47)COMPLIED

	48) COMPLIED

	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714
	[email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2007-10-23			Cont ID
Sent By	rmcdouga			Date	2007-10-23	Time	09:52	Rev Time	0.00
Received By	rmcdouga			Date	2007-10-23	Time	09:52	Sent To

Notes

2007-10-23 09:51:55	2004 FBC W/2007 SUPPLEMENTS
	NSFR

	DENIED BY BUILDING

	1) COMPLIED

	2) A RECORDED COPY OF THE NOTICE OF COMMENCEMENT
	MUST BE SUBMITTED BEFORE A
	PERMIT CAN BE ISSUED. WORK MUST COMMENCE WITHIN 90 DAYS
	OF THE DATE THE NOC IS RECORDED. FS 713.13.

	3) IMPACT FEES MUST BE PAID TO PALM
	BEACH COUNTY, PLANS STAMPED BY THEM AND
	COPY OF RECEIPT SUBMITTED TO CITY OF
	WEST PALM BEACH BUILDING DEPARTMENT,
	BEFORE A BUILDING PERMIT CAN BE ISSUED.

	4)THE PLANS SPECIFY TYPE III UNPROTECTED
	CONSTRUCTION, WHICH UNDER THE 2004 CODE IS TYPE III-B.
	PLEASE SPECIFY A OR B ON THE PLANS. SEE FBC CHAPTER 6.
	NOTE: TYPE III CONSTRUCTION REQUIRES EXTERIOR WALLS TO
	HAVE A TWO HOUR FIRE RATING IN ADDITION TO OTHER
	REQUIREMENTS. SEE TABLES 601 AND 602. NOTE: THIS
	STRUCTURE COULD BE DECLARED TYPE V-B CONSTRUCTIONAND
	IT WOULD STILL COMPLY WITH THE HEIGHT AND AREA
	REQUIREMENTS OF TABLE 503. TYPE V-B CONSTRUCTION DOES
	NOT REQUIRE THE EXTERIOR WALLS TO BE FIRE RATED. IF YOU
	ARE SPECIFYING TYPE III CONSTRUCTION SUBMIT
	CALCULATIONS AS TO HOW THE 2 HOUR FIRE RATING WILL BE
	OBTAINED. SUBMIT A LETTER FROM THE CONCRETE BLOCK
	SUPPLIER THAT SPECIES THE THICKNESS AND AGGREGATE IN
	THE BLOCK AND THE FIRE RESISTANCE RATING IN HOURS.

	5)FBC R401.4AREA OF QUESTIONABLE
	SOIL.SUBMIT A GEOTECHNICAL REPORT
	TO VERIFY THE SAFE BEARING CAPACITY OF
	THE SOIL. SUBMIT 2 SIGNED AND SEALED COPIES.

	6) THE PLANS ARE REQUIRED TO HAVE THE CERTIFICATE OF
	AUTHORIZATION NUMBERS OF THE ENGINEERING AND
	ARCHITECTURAL FIRMS. SEE FS 471 AND 481. ALSO SEE THE
	ELECTRICAL REVIEW COMMENTS.

	7) THE FLOOD ZONE DESIGNATION ON THE SURVEY IS
	SPECIFIED AS A8, WHICH IS INCORRECT. THIS AREA IS
	INCLUDED IN THE LETTER OF MAP REVISION (LOMR) FOR THE
	VILLAGES OF PALM BEACH LAKES AND SPENCER LAKES PLATS
	1,2 AND 3 DATED DECEMBER 3, 1983. PLEASE CORRECT.

	8) THE ENERGY CALCULATIONS LIST THE CONDITIONED FLOOR
	AREA AS 8000 SQFT AND THE PLANS SPECIFY 8327 SQFT.
	PLEASE CORRECT. FBC R CHAPTER 11 AND FBC CHAPTER 13

	9)NOTE THAT THE DEFINITION FOR EXPOSURE C HAS CHANGED
	EFFECTIVE DECEMBER 8, 2006 (2006 AMENDMENTS TO THE
	FBC), FBC1609.4, FBC R301.2.1.4.
	EXPOSURE C. OPEN TERRAIN WITH SCATTERED
	OBSTRUCTIONS, INCLUDING SURFACE UNDULATIONS OR OTHER
	IRREGULARITIES, HAVING HEIGHTS GENERALLY LESS THAN 30
	FEET (9144 MM) EXTENDING MORE THAN 1,500 FEET (457.2 M)
	FROM THE BUILDING SITE IN ANY QUADRANT. THIS EXPOSURE
	SHALL ALSO APPLY TO ANY BUILDING LOCATED WITHIN
	EXPOSURE B-TYPE TERRAIN WHERE THE BUILDING IS DIRECTLY
	ADJACENT TO OPEN AREAS OF EXPOSURE C-TYPE TERRAIN IN
	ANY QUADRANT FOR A DISTANCE OF MORE THAN 600 FEET
	(182.9 M). THE STRUCTURE IS LOCATED ADJACENT TO A GOLF
	COURSE WHICH MAY REQUIRE IT TO BE DESIGNED AS EXPOSURE
	C. PLEASE REVISE PLANS OR INDICATE WHY THE EXPOSURE
	CATEGORY SHOULD NOT BE CHANGED.

	10) THE WALLS OF THE WINE ROOM ARE REQUIRED TO BE
	WATERPROOFED IN ACCORDANCE WITH FBC R406. INDICATE HOW
	THIS WILL BE ACCOMPLISHED ON THE PLANS.

	11) PROVIDE DETAILS OF THE MASONRY FIREPLACES AND
	CHIMNEYS IN THE LIVING ROOM AND AT THE COVERED PATIO.
	SEE SECTIONS R1001 AND R1003.SPECIFY REINFORCING,
	ETC.

	12) PROVIDE DETAILS FOR THE PRE-FAB FIREPLACE AND
	CHIMNEY. SUBMIT THE MANUFACTURER'S SPECIFICATIONS AND
	LISTING INFORMATION FOR THE FIREPLACE AND CHIMNEY. FBC
	R1002 AND R1004

	13) PROVIDE DETAILS FOR THE CHIMNEY CAPS. SPECIFY
	MATERIALS, ATTACHMENTS, FASTENERS, ETC. FBC 106.1.1
	CITY AMENDMENTS.

	14) PROVIDE STRUCTURAL DETAILS FOR THE WOOD FRAME FALSE
	CHIMNEY. SPECIFY MATERIALS, CONNECTIONS, ETC. FBC
	106.1.1 CITY AMENDMENTS.

	15) AT INTERIOR STAIRS AND SECOND FLOOR LANDING SHOW
	COMPLIANCE WITH R312.2 GUARD OPENING LIMITATIONS.
	REQUIRED GUARDS ON OPEN SIDES OF STAIRWAYS, RAISED
	FLOOR AREAS, BALCONIES AND PORCHES SHALL HAVE
	INTERMEDIATE RAILS OR ORNAMENTAL CLOSURES WHICH DO NOT
	ALLOW PASSAGE OF A SPHERE 4 INCHES (102MM) OR MORE IN
	DIAMETER.

	16) SHOW COMPLIANCE WITH R807.1 ATTIC ACCESS .
	IN BUILDINGS WITH COMBUSTIBLE CEILING OR ROOF
	CONSTRUCTION, AN ATTIC ACCESS OPENING SHALL BE PROVIDED
	TO ATTIC AREAS THAT EXCEED 30 SQUARE FEET (2.8 M 2 )
	AND HAVE A VERTICAL HEIGHT OF 30 INCHES (762 MM) OR
	GREATER. THE ROUGH-FRAMED OPENING SHALL NOT BE LESS
	THAN 22 INCHES BY 30 INCHES (559 MM BY 762 MM) AND
	SHALL BE LOCATED IN A HALLWAY OR OTHER READILY
	ACCESSIBLE LOCATION. NO ATTIC ACCESS IS SPECIFIED ON
	THE SECOND FLOOR.

	17)COMPLIED

	18) SUBMIT THE MANUFACTURER'S SPECIFICATIONS AND
	LISTING FOR THE OUTDOOR BBQ ON THE COVERED PORCH.
	INCLUDE SPECS. AND LISTING FOR HOOD IF ONE IS REQUIRED.
	FBC 106.1.1 CITY AMENDMENTS.

	19) SPECIFY THE CEILING FINISHES FOR THE FRONT PORCH,
	LOGGIA AND COVERED PATIO. FBC 106.1.1 CITY AMENDMENTS.

	20) THE ROOF/FLOOR DRAIN AT THE FRONT PORCH IS REQUIRED
	TO DISCHARGE AT LEAST 1 FOOT AWAY FROM THE STRUCTURE IN
	ACCORDANCE WITH R320.7. SPECIFY ON THE PLANS.

	21) SHOW COMPLIANCE WITH R502.1.2 DRAFTSTOPPING
	REQUIRED.
	WHEN THERE IS USABLE SPACE BOTH ABOVE AND BELOW THE
	CONCEALED SPACE OF A FLOOR/CEILING ASSEMBLY, DRAFTSTOPS
	SHALL BE INSTALLED SO THAT THE AREA OF THE CONCEALED
	SPACE DOES NOT EXCEED 1,000 SQUARE FEET (92.9 M 2 ).
	DRAFTSTOPPING SHALL DIVIDE THE CONCEALED SPACE INTO
	APPROXIMATELY EQUAL AREAS. WHERE THE ASSEMBLY IS
	ENCLOSED BY A FLOOR MEMBRANE ABOVE AND A CEILING
	MEMBRANE BELOW DRAFTSTOPPING SHALL BE PROVIDED IN
	FLOOR/CEILING ASSEMBLIES UNDER THE FOLLOWING
	CIRCUMSTANCES:
	1.CEILING IS SUSPENDED UNDER THE FLOOR FRAMING. 2.
	FLOOR FRAMING IS CONSTRUCTED OF TRUSS-TYPE OPEN-WEB OR
	PERFORATED MEMBERS.
	R502.1.2.1 MATERIALS.
	DRAFTSTOPPING MATERIALS SHALL NOT BE LESS THAN 1/2-INCH
	(12.7 MM) GYPSUM BOARD, 3 / 8 -INCH (9.5 MM) WOOD
	STRUCTURAL PANELS, 3 / 8 -INCH (9.5 MM) TYPE 2-M-W
	PARTICLEBOARD OR OTHER APPROVED MATERIALS ADEQUATELY
	SUPPORTED. DRAFTSTOPPING SHALL BE INSTALLED PARALLEL TO
	THE FLOOR FRAMING MEMBERS UNLESS OTHERWISE APPROVED BY
	THE BUILDING OFFICIAL. THE INTEGRITY OF ALL DRAFTSTOPS
	SHALL BE MAINTAINED.
	SPECIFY THE MATERIAL THAT WILL BE USED AND LOCATIONS ON
	THE PLANS.

	22)COMPLIED

	23) REVISE GENERAL NOTE E(2) ON A9 TO SPECIFY ACI
	315-02 AND NOTE F(2) FROM SBC TO FBC. WHICH ARE THE
	CORRECT REFERENCES PER 2004 FBC RESIDENTIAL CHAPTER
	43.

	24) ON SHEET S1.01, NOTE 2 INCORRECTLY LISTS S3.01 AS
	THE SHEET CONTAINING THE WINDOW AND DOOR PRESSURES. THE
	TABLE IS LOCATED ON S 3.02.

	25) PLEASE SPECIFY THE COMPONENT AND CLADDING PRESSURES
	AT EACH OF THE OPENINGS ON THE PLANS BASED ON THE
	OPENING SIZES, EXPOSURE CATEGORY AND LOCATIONS. FBC *
	106.1.2

	26) COMPLIED

	27) ON SHEET A.01 THE STAIR CALCULATIONS ARE INCORRECT.
	THE SUM OF THE 2 RISERS AND A TREAD IS 23.95" NOT 24"
	AS SPECIFIED, WHICH IS NOT BETWEEN 24 AND 25 INCHES.
	SEE FBC R311.5.3.2 PLEASE CORRECT.

	28) THE (2)LB-3 BEAMS SPECIFIED AT THE COVERED PORCH
	ON SHEET S2.01 ARE NOT LISTED IN THE SECOND BEAM
	SCHEDULE ON SHEET S2.01. PLEASE CORRECT. FBC 106.1.2
	CITY AMENDMENTS

	29) THE SIMPSON H10 OR USP RT16 "R" IN SCHEDULE ON
	S2.02) WILL NOT WORK FOR ATTACHING THE FLOOR TRUSSES TO
	THE LEDGERS. THE FLOOR TRUSSES ARE 3-1/2" WIDE AND THE
	CONNECTORS HAVE A 1-9/16" OPENING FOR THE TRUSS. PLEASE
	CORRECT.

	30) N/A

	31) CONNECTOR "L" IN THE SCHEDULE ON S2.02A SIMPSON
	MTSM 20,REQUIRES 4 CONCRETE SCREWS TO ACHIEVE THE
	UPLIFT SPECIFIED. ONLY 3 FASTENERS ARE SPECIFIED IN THE
	SCHEDULE. PLEASE CORRECT.

	32) CONNECTOR "N" ON S2.O2 , THE SIMPSON HTT22 IS
	INCORRECTLY SPECIFIED WITH 3/4" DIA. ANCHORS AND THE
	SIMPSON CATALOG SPECS. 5/8" DIA ANCHORS. PLEASE
	CORRECT.

	33) NOTE #4 ON SHEETS S2.01 AND S2.02 STATE SEE PLYWOOD
	NAILING SCHEDULE ON THIS SHEET AND THE SCHEDULE IS ON
	SHEET S3.02. PLEASE CORRECT.

	34) CORRECTED

	35) THE TRUSS LAYOUT IS REQUIRED TO BE REVIEWED AND
	APPROVED IN WRITING BY THE DESIGNER OF RECORD FOR THE
	STRUCTURE. R802.1.6 AND FBC106.1.1.2 CITY AMENDMENTS

	36) THE ROOF TRUSSES ARE REQUIRED TO HAVE A MINIMUM
	BOTTOM CORD LIVE LOAD OF 10 PSF. SEE TABLE R301.5.
	PLEASE CORRECT.

	37) THE TRUSS DRAWING SUBMITTAL DOES NOT MEET THE
	REQUIREMENTS OF FAC 61G-15-31.003. PLEASE SEPARATE THE
	DRAWINGS AND PLACE THEM WITH THE APPROPRIATE COVER
	SHEETS AND NUMBER THE DRAWINGS TO CORRESPOND TO THE
	NUMBERING ON THE COVERSHEETS.

	38) THE PLYWOOD SHEATHING FASTENING SCHEDULE FOR WALLS
	AND ROOFS ON S 3.02 SPECIFIES #8 SCREWS AND THE NOTE
	CALLS FOR 2-1/2" SELF DRILLING SCREWS FOR ATTACHING TO
	A METAL DECK.THE SHEATHING AND FRAMING FOR THIS
	PROJECT IS WOOD. PLEASE CORRECT. FBC R803.2.3.1
	REQUIRES 8D RING SHANK NAILS IN ALL ROOF ZONES. PLEASE
	CORRECT.

	39)CORRECTED

	40) FBC 106.3* CITY AMENDMENTS PRODUCT
	APPROVALS. THOSE PRODUCT WHICH ARE
	REGULATED BY DCA RULE 9B-72 SHALL BE
	REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD PRIOR TO SUBMITTAL
	FOR JURISDICTIONAL APPROVAL.

	41) SPECIFY THE METHOD OF ATTACHMENT THAT WILL BE USED
	TO INSTALL THE ROOF TILES. PLEASE CIRCLE THE
	APPROPRIATE METHOD FROM THOSE LISTED IN THE PRODUCT
	APPROVAL NOA. FBC 106.1.2 CITY AMENDMENTS.

	42)THE GENERIC PRESSURES IN THE SCHEDULE ON S3.02 ARE
	TOO HIGH FOR THE GARAGE DOORS. SEE TABLE R301.2(4).
	PLEASE INDICATE THE REQUIRED OPENING PRESSURES FOR THE
	GARAGE DOORS ON THE PLANS.

	43)SUBMIT THE PRODUCT EVALUATION REPORT AND
	INSTALLATION INSTRUCTIONS FOR THE NAN YA PLASTIC CORP.
	EXTERIOR DOORS IN ACCORDANCE WITH FAC RULE 9B-72.

	44) SUBMIT PRODUCT APPROVALS FOR THE FIXED WINDOWS AS
	REQUIRED BY FAC RULE 9B-72.

	45) CORRECTED

	46) THE LOCAL PRODUCT APPROVAL APPLICATION FOR THE
	"SIGNATURE DOOR INC." EXTERIOR DOORS IS INCOMPLETE.
	SUBMIT THE EVALUATION REPORT, INSTALLATION
	INSTRUCTIONS, ETC. REQUIRED BY FAC RULE 9B-72.

	47)ON THE FIRST FLOOR PLAN SHEET A.01, THERE IS A
	WALL TYPE 6 SPECIFIED. HOWEVER, THIS WALL TYPE IS NOT
	LISTED IN THE WALL SCHEDULE. PLEASE CORRECT. FBC
	106.1.2 CITY AMENDMENTS.

	48) IN ORDER TO EXPEDITE PLAN REVIEW AND HELP AVOID
	ADDITIONAL PLAN REVIEWS, PLEASE INCLUDE A RESPONSE
	LETTER SPECIFYING HOW THE COMMENTS HAVE BEEN
	ADDRESSED.


	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714
	[email protected]

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2007-09-18			Cont ID
Sent By	rmcdouga			Date	2007-09-18	Time	14:45	Rev Time	0.00
Received By	rmcdouga			Date	2007-09-12	Time	18:04	Sent To

Notes

2007-09-17 17:26:36	2004 FBC W/2007 SUPPLEMENTS
	NSFR

	DENIED BY BUILDING

	1) UNITY OF TITLE FOR THE LOTS MUST BE COMPLETED AND
	ADDRESS ASSIGNED BEFORE PERMIT IS ISSUED.

	2) A RECORDED COPY OF THE NOTICE OF COMMENCEMENT
	MUST BE SUBMITTED BEFORE A
	PERMIT CAN BE ISSUED.

	3) IMPACT FEES MUST BE PAID TO PALM
	BEACH COUNTY, PLANS STAMPED BY THEM AND
	COPY OF RECEIPT SUBMITTED TO CITY OF
	WEST PALM BEACH BUILDING DEPARTMENT,
	BEFORE A BUILDING PERMIT CAN BE ISSUED.

	4)THE PLANS SPECIFY TYPE III UNPROTECTED
	CONSTRUCTION, WHICH UNDER THE 2004 CODE IS TYPE III-B.
	PLEASE SPECIFY A OR BE ON THE PLANS. SEE FBC CHAPTER 6.
	NOTE: TYPE III CONSTRUCTION REQUIRES EXTERIOR WALLS TO
	HAVE A TWO HOUR FIRE RATING IN ADDITION TO OTHER
	REQUIREMENTS. SEE TABLES 601 AND 602. NOTE: THIS
	STRUCTURE COULD BE DECLARED TYPE V-B CONSTRUCTIONAND
	IT WOULD STILL COMPLY WITH THE HEIGHT AND AREA
	REQUIREMENTS OF TABLE 503. TYPE V-B CONSTRUCTION DOES
	NOT REQUIRE THE EXTERIOR WALLS TO BE FIRE RATED. IF YOU
	ARE SPECIFYING TYPE III CONSTRUCTION SUBMIT
	CALCULATIONS AS TO HOW THE 2 HOUR FIRE RATING WILL BE
	OBTAINED. SUBMIT A LETTER FROM THE CONCRETE BLOCK
	SUPPLIER THAT SPECIES THE THICKNESS AND AGGREGATE IN
	THE BLOCK AND THE FIRE RESISTANCE RATING IN HOURS.

	5)FBC R401.4AREA OF QUESTIONABLE
	SOIL.SUBMIT A GEOTECHNICAL REPORT
	TO VERIFY THE SAFE BEARING CAPACITY OF
	THE SOIL. SUBMIT 2 SIGNED AND SEALED COPIES.

	6) THE PLANS ARE REQUIRED TO HAVE THE ORIGINAL
	SIGNATURE OF THE ENGINEER AND ARCHITECT IN ADDITION TO
	THE LICENSE NUMBERS OF THE ENGINEERING AND
	ARCHITECTURAL FIRMS. SEE FS 471 AND 481. SEE THE
	ELECTRICAL REVIEW COMMENTS.

	7) THE FLOOD ZONE DESIGNATION ON THE SURVEY IS
	SPECIFIED AS A8, WHICH IS INCORRECT. THIS AREA IS
	INCLUDED IN THE LETTER OF MAP REVISION (LOMR) FOR THE
	VILLAGES OF PALM BEACH LAKES AND SPENCER LAKES PLATS
	1,2 AND 3 DATED DECEMBER 3, 1983. PLEASE CORRECT.

	8) THE ENERGY CALCULATIONS LISTS THE CONDITIONED FLOOR
	AREA AS 8000 SQFT AND THE PLANS SPECIFY 8327 SQFT.
	PLEASE CORRECT.

	9)NOTE THAT THE DEFINITION FOR EXPOSURE C HAS CHANGED
	EFFECTIVE DECEMBER 8, 2006 (2006 AMENDMENTS TO THE
	FBC), FBC1609.4, FBC R301.2.1.4.
	EXPOSURE C. OPEN TERRAIN WITH SCATTERED
	OBSTRUCTIONS, INCLUDING SURFACE UNDULATIONS OR OTHER
	IRREGULARITIES, HAVING HEIGHTS GENERALLY LESS THAN 30
	FEET (9144 MM) EXTENDING MORE THAN 1,500 FEET (457.2 M)
	FROM THE BUILDING SITE IN ANY QUADRANT. THIS EXPOSURE
	SHALL ALSO APPLY TO ANY BUILDING LOCATED WITHIN
	EXPOSURE B-TYPE TERRAIN WHERE THE BUILDING IS DIRECTLY
	ADJACENT TO OPEN AREAS OF EXPOSURE C-TYPE TERRAIN IN
	ANY QUADRANT FOR A DISTANCE OF MORE THAN 600 FEET
	(182.9 M). THE STRUCTURE IS LOCATED ADJACENT TO A GOLF
	COURSE WHICH MAY REQUIRE IT TO BE DESIGNED AS EXPOSURE
	C. PLEASE REVISE PLANS OR INDICATE WHY THE EXPOSURE
	CATEGORY SHOULD NOT BE CHANGED.

	10) THE WALLS OF THE WINE ROOM ARE REQUIRED TO BE
	WATERPROOFED IN ACCORDANCE WITH FBC R406.

	11) PROVIDE DETAILS OF THE MASONRY FIREPLACES AND
	CHIMNEYS IN THE LIVING ROOM AND AT THE COVERED PATIO.
	SEE SECTIONS R1001 AND R1003. COORDINATE WITH THE
	STRUCTURAL ENGINEER FOR THE FOUNDATION REQUIREMENTS.
	SPECIFY REINFORCING, ETC.

	12) PROVIDE DETAILS FOR THE PRE-FAB FIREPLACE AND
	CHIMNEY. SUBMIT THE MANUFACTURER'S SPECIFICATIONS AND
	LISTING INFORMATION FOR THE FIREPLACE AND CHIMNEY.

	13) PROVIDE DETAILS FOR THE CHIMNEY CAPS. SPECIFY
	MATERIALS, ATTACHMENTS, FASTENERS, ETC.

	14) PROVIDE STRUCTURAL DETAILS FOR THE WOOD FRAME FAKE
	CHIMNEY. SPECIFY MATERIALS, CONNECTIONS, ETC.

	15) AT INTERIOR STAIRS AND SECOND FLOOR LANDING SHOW
	COMPLIANCE WITH R312.2 GUARD OPENING LIMITATIONS.
	REQUIRED GUARDS ON OPEN SIDES OF STAIRWAYS, RAISED
	FLOOR AREAS, BALCONIES AND PORCHES SHALL HAVE
	INTERMEDIATE RAILS OR ORNAMENTAL CLOSURES WHICH DO NOT
	ALLOW PASSAGE OF A SPHERE 4 INCHES (102MM) OR MORE IN
	DIAMETER.

	16) SHOW COMPLIANCE WITH R807.1 ATTIC ACCESS .
	IN BUILDINGS WITH COMBUSTIBLE CEILING OR ROOF
	CONSTRUCTION, AN ATTIC ACCESS OPENING SHALL BE PROVIDED
	TO ATTIC AREAS THAT EXCEED 30 SQUARE FEET (2.8 M 2 )
	AND HAVE A VERTICAL HEIGHT OF 30 INCHES (762 MM) OR
	GREATER. THE ROUGH-FRAMED OPENING SHALL NOT BE LESS
	THAN 22 INCHES BY 30 INCHES (559 MM BY 762 MM) AND
	SHALL BE LOCATED IN A HALLWAY OR OTHER READILY
	ACCESSIBLE LOCATION.

	17)SHOW COMPLIANCE WITH R310 FOR EMERGENCY ESCAPE AND
	RESCUE OPENINGS AT THE SLEEPING ROOMS. SPECIFY THE
	SECOND FLOOR EGRESS WINDOWS ON THE PLANS.

	18) SUBMIT THE MANUFACTURER'S SPECIFICATIONS AND
	LISTING FOR THE OUTDOOR BBQ ON THE COVERED PORCH.
	INCLUDE SPECS. AND LISTING FOR HOOD IF ONE IS
	REQUIRED.

	19) SPECIFY THE CEILING FINISHES FOR THE FRONT PORCH,
	LOGGIA AND COVERED PATIO.

	20) THE ROOF/FLOOR DRAIN AT THE FRONT PORCH IS REQUIRED
	TO DISCHARGE AT LEAST 1 FOOT AWAY FROM THE STRUCTURE IN
	ACCORDANCE WITH R320.7.

	21) SHOW COMPLIANCE WITH R502.1.2 DRAFTSTOPPING
	REQUIRED.
	WHEN THERE IS USABLE SPACE BOTH ABOVE AND BELOW THE
	CONCEALED SPACE OF A FLOOR/CEILING ASSEMBLY, DRAFTSTOPS
	SHALL BE INSTALLED SO THAT THE AREA OF THE CONCEALED
	SPACE DOES NOT EXCEED 1,000 SQUARE FEET (92.9 M 2 ).
	DRAFTSTOPPING SHALL DIVIDE THE CONCEALED SPACE INTO
	APPROXIMATELY EQUAL AREAS. WHERE THE ASSEMBLY IS
	ENCLOSED BY A FLOOR MEMBRANE ABOVE AND A CEILING
	MEMBRANE BELOW DRAFTSTOPPING SHALL BE PROVIDED IN
	FLOOR/CEILING ASSEMBLIES UNDER THE FOLLOWING
	CIRCUMSTANCES:
	1.CEILING IS SUSPENDED UNDER THE FLOOR FRAMING. 2.
	FLOOR FRAMING IS CONSTRUCTED OF TRUSS-TYPE OPEN-WEB OR
	PERFORATED MEMBERS.
	R502.1.2.1 MATERIALS.
	DRAFTSTOPPING MATERIALS SHALL NOT BE LESS THAN ?-INCH
	(12.7 MM) GYPSUM BOARD, 3 / 8 -INCH (9.5 MM) WOOD
	STRUCTURAL PANELS, 3 / 8 -INCH (9.5 MM) TYPE 2-M-W
	PARTICLEBOARD OR OTHER APPROVED MATERIALS ADEQUATELY
	SUPPORTED. DRAFTSTOPPING SHALL BE INSTALLED PARALLEL TO
	THE FLOOR FRAMING MEMBERS UNLESS OTHERWISE APPROVED BY
	THE BUILDING OFFICIAL. THE INTEGRITY OF ALL DRAFTSTOPS
	SHALL BE MAINTAINED.
	SPECIFY THE MATERIAL AND LOCATIONS ON THE PLAN.

	22)REVISE THE TYPICAL DOOR JAMB DETAIL 7 ON A9. THE
	2X OR 1X BUCKS ARE REQUIRED TO BE THE FULL WIDTH OF THE
	JAMB. SEE R613.6.1.1

	23) REVISE GENERAL NOTE E(2) ON A9 TO SPECIFY ACI
	315-02 AND NOTE F(2) FROM SBC TO FBC. WHICH ARE THE
	CORRECT REFERENCES PER 2004 FBC RESIDENTIAL CHAPTER
	43.

	24) ON SHEET S1.01, NOTE 2 INCORRECTLY LISTS S3.01 AS
	THE SHEET CONTAINING THE WIDOW AND DOOR PRESSURES. THE
	TABLE IS LOCATED ON S 3.02.

	25) PLEASE SPECIFY THE COMPONENT AND CLADDING PRESSURES
	AT EACH OF THE OPENINGS ON THE PLANS BASED ON THE
	OPENING SIZES, EXPOSURE CATEGORY AND LOCATIONS. FBC *
	106.1.2

	26) ON SHEET S1.01 THE NOTE FOR CAP PLATE C REFERS TO
	DETAIL 8 ON S3.01, WHICH IS NOT CORRECT. PLEASE
	CORRECT. SEE 8 ON S3.02.

	27) ON PAGE A1 THE SUM OF 2 RISERS AND A TREAD IS
	23.95", WHICH IS NOT BETWEEN 24 AND 25 INCHES. PLEASE
	CORRECT.

	28) THE LB-3 BEAMS ARE NOT LISTED IN THE SECOND BEAM
	SCHEDULE ON SHEET S2.01.

	29) THE SIMPSON H10 OR USP RT16 ("R" IN SCHEDULE ON
	S2.02) WILL NOT WORK FOR ATTACHING THE FLOOR TRUSSES TO
	THE LEDGERS. THE FLOOR TRUSSES ARE 3-1/2" WIDE AND THE
	CONNECTORS HAVE A 1-9/16" OPENING FOR THE TRUSS.

	30) THE SCHEDULE SPECIFIES CONNECTOR "W" WHICH IS TWO
	SIMPSON H10 OR TWO USP RT16 TRUSS ANCHORS. SOME OF THE
	TRUSSES THAT HAVE THESE CONNECTORS SPECIFIED DO NOT
	EXTEND PAST THE 2 X 6 WALL SO THEY CAN NOT BE APPLIED
	TO EACH SIDE OF THE WALL AND THE TRUSS.

	31) CONNECTOR "L" IN THE SCHEDULE ON S2.02A SIMPSON
	MTSM 20,REQUIRES 4 CONCRETE SCREWS TO ACHIEVE THE
	UPLIFT SPECIFIED. ONLY 3 FASTENERS ARE SPECIFIED IN THE
	SCHEDULE. PLEASE CORRECT.

	32) CONNECTOR "N" ON S2.O2 , THE SIMPSON HTT22 IS
	INCORRECTLY SPECIFIED WITH 3/4" DIA. ANCHORS AND THE
	SIMPSON CATALOG SPECS. 5/8" DIA ANCHORS. PLEASE
	CORRECT.

	33) NOTE #4 ON SHEETS S2.01 AND S2.02 STATE SEE PLYWOOD
	NAILING SCHEDULE ON THIS SHEET AND THE SCHEDULE IS ON
	SHEET S3.02. PLEASE CORRECT.

	34) ALL OF THE DETAILS ON SHEET S3.02 ARE INCORRECTLY
	LABELED AS BEING ON S3.01.

	35) THE TRUSS LAYOUT IS REQUIRED TO BE REVIEWED AND
	APPROVED IN WRITING BY THE DESIGNER OF RECORD FOR THE
	STRUCTURE.

	36) THE ROOF TRUSSES ARE REQUIRED TO HAVE A MINIMUM
	BOTTOM CORD LIVE LOAD OF 10 PSF. SEE TABLE R301.5.

	37) THE TRUSS DRAWING SUBMITTAL DOES NOT MEET THE
	REQUIREMENTS OF 61G-15-31.003. PLEASE SEPARATE THE
	DRAWINGS AND PLACE THEM WITH THE APPROPRIATE COVER
	SHEETS AND NUMBER THE DRAWINGS TO CORRESPOND TO THE
	NUMBERING ON THE COVERSHEETS.

	38) THE PLYWOOD SHEATHING FASTENING SCHEDULE FOR WALLS
	AND ROOFS ON S 3.02 SPECIFIES #8 SCREWS AND THE NOTE
	CALLS FOR 2-1/2" SELF DRILLING SCREWS FOR ATTACHING TO
	A METAL DECK.THE SHEATHING AND FRAMING FOR THIS
	PROJECT IS WOOD. PLEASE CORRECT. FBC R803.2.3.1
	REQUIRES 8D RING SHANK NAILS IN ALL ROOF ZONES.

	39)PRODUCT APPROVALS SUBMITTED WITH PERMIT
	APPLICATION AFTER OCTOBER 1, 2003 ARE REQUIRED TO
	COMPLY WITH THE FLORIDA PRODUCT APPROVAL SYSTEM. FOR
	INFORMATION PLEASE SEE THE STATE WEBSITE AT
	WWW.FLORIDABUILDING.ORG. PRODUCTS WITH STATEWIDE
	APPROVAL ARE REQUIRED TO BE SUBMITTED WITH A COVER
	SHEET THAT LISTS THE PRODUCT IDENTITY NUMBER FROM THE
	STATE.

	40)WPB ADMIN CODE 106.3* PRODUCT
	APPROVALS. THOSE PRODUCT WHICH ARE
	REGULATED BY DCA RULE 9B-72 SHALL BE
	REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD PRIOR TO SUBMITTAL
	FOR JURISDICTIONAL APPROVAL.

	41) CIRCLE THE METHOD OF ATTACHMENT THAT WILL BE USED
	TO INSTALL THE ROOF TILE ON THE NOA.

	42)THE GENERIC PRESSURES IN THE SCHEDULE ON S3.02 ARE
	TOO HIGH FOR THE GARAGE DOORS. SEE TABLE R301.2(4).

	43)SUBMIT STATE OR MIAMI-DADE PRODUCT APPROVALS FOR
	THE NAN YA PLASTIC CORP. EXTERIOR DOORS OR THE
	MANUFACTURER CAN APPLY FOR LOCAL PRODUCT APPROVAL IN
	ACCORDANCE WITH RULE 9B-72.

	44) THE WEATHERSHIELD LEGACY FIXED WINDDOW NOA NO.
	05-0420.04 IS MISSING SHEET 4 OF 4 FROM DRAWING NO.
	1071.

	45) THE NOA NO. 03-1105.01 FOR THE PGT PW-701 WINDOW
	HAS BEEN REVISED BY NOA NO. 07-0418.06.

	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714
	[email protected]

Review Stop	E			ELECTRICAL
Rev No	5	Status	P	Date	2009-09-28			Cont ID
Sent By	dpalmer			Date	2009-09-28	Time	13:09	Rev Time	0.00
Received By	dpalmer			Date	2009-09-28	Time	13:09	Sent To	PC

Notes

2009-09-28 13:11:33	** REDLINED PLANS

	110.26 FOR A/C DISCONNECT
	250.122 FOR MISSING EQUIPMENT GROUNDING CONDUCTOR AFTER
	MAIN DISCONNECT.
	SUCCESSOR ARCHITECT TO BE COMPLETED BY ARCHITECT PER
	FLORIDA ADMINSTRATIVE CODE 61G1-16. LETTER SUBMITTED
	ONLY LISTED NEW ARCHITECT AS TAKING OVER.

Review Stop	E			ELECTRICAL
Rev No	4	Status	F	Date	2009-07-20			Cont ID
Sent By	dpalmer			Date	2009-07-20	Time	14:40	Rev Time	0.00
Received By	dpalmer			Date	2009-07-20	Time	14:40	Sent To

Notes

2009-07-20 14:40:50

	DENIED REVISION

	** THE TITLE BLOCKS INDICATE THERE HAVE BEEN THREE
	REVISIONS SINCE THE LAST REVIEW DONE IN THIS OFFICE
	SINCE 12/03/07 HOWEVER TO DATE NO ELECTRICAL REVISIONS
	HAVE BEEN SUBMITTED FOR BASE BUILDING PLANS.
	THE SERVICE HAS COMPLETELY BEEN REVISED ALONG WITH MANY
	OTHER ITEMS.


	1) NOTE: PLANS SUBMITTED ARE NOT REVISED BY THE
	ENGINEER OF RECORD PER FS 471.025
	FAC 61G15-23

	2) NOTE: PLEASE UPDATE LOAD CALCULATIONS FOR RECESSED
	LIGHTING LOADS PER 220.3B4. THE AMOUNT OF RECESSED
	LIGHTING SHOWN ON PLANS IS ABOVE THE GENERAL LIGHTING
	LOADS. PLEASE ALSO BE SURE THE ADDITIONAL LOADS ON THE
	LIGHTING PANEL IS COORDINATED.

	3) NOTE: PLEASE LOOK AT THE NEW 600AMP DISTRIBUTION
	PANEL. ALL PANELS ARE SHOWING FEEDER CONDUCTORS AND
	LOADS WELL BELOW ANY MINIMUMS BY CODE. 240.4,310.16 ETC
	FOR EXAMPLE: PANEL A IS SHOWING A 225AMP BREAKER WITH
	#10 CONDUCTORS AS THE FEEDERS WITH A LOAD OF 4.5 KW.
	THIS IS NOT POSSIBLE. ALL OTHER PANELS ON THIS SAME
	600AMP MDP IS THE SAME. CONDUCTORS ARE TOO SMALL AND
	LOADS ARE NOT ACCURATE.

	4) NOTE: PANELS FOR ALL LOADS NEED TO BE SUBMITTED AND
	COMPLETE. NO PANEL SCHEDULE FOR EXAMPLE WAS SUBMITTED
	FOR THE NEW POOL PANEL SO LOADS, BRANCH CIRCUITS ETC
	CAN NOT BE VERIFIED AS CODE COMPLIANT.
	408.4,220,310, ETC

	5) NOTE: THE RISER HAS BEEN COMPLETELY REVISED FOR A
	NEW 600AMP SERVICE HOWEVER THE PLANS ON SHEETS E- STILL
	INDICATES THE ORIGINAL 400AMP SERVICE, 400AMP MAIN AND
	400AMP TRANSFER SWITCH.
	PLEASE COORDINATE PLANS.
	215.5,230.70,230.71,ETC

	6) NOTE: PLEASE SUBMIT THE MANUFACTURES SPECS/CUT
	SHEETS FOR THE NEW TRANSFER SWITCH WHICH APPEARS TO BE
	UPDATED FROM THE PREVIOUS PLANS.
	110.3, 90.7

	7) NOTE: PLEASE SEE SAFE ROOM WHICH WAS/IS THE MASTER
	BEDROOM CLOSET. THE PLANS INDICATE WHAT APPEAR TO BE
	WALL SCONCES. PLEASE SEE 410.8 FOR MINIMUM CLEARANCES
	FROM SHELVING.





	IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT
	TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO
	CONTACT THIS REVIEWER.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW II
	CONSTRUCTION SERVICES DEPARTMENT
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]

Review Stop	E			ELECTRICAL
Rev No	3	Status	P	Date	2007-12-20			Cont ID
Sent By	dpalmer			Date	2007-12-03	Time	13:18	Rev Time	0.00
Received By	dpalmer			Date	2007-12-03	Time	13:17	Sent To

Notes

***NONE***

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2007-10-06			Cont ID
Sent By	dpalmer			Date	2007-10-06	Time	16:56	Rev Time	0.00
Received By	dpalmer			Date	2007-10-06	Time	15:00	Sent To	M

Notes

2007-10-06 16:56:20
	* DENIED2ND REVIEW *

	** PLEASE SEE SOME COMMENTS FROM PREVIOUS REVIEW STILL
	NEED TO BE ADDRESSED.
	** PLEASE SEE NEW NOTE DUE TO CHANGE IN NOTE ON PLANS.

	1) NOTE: PLEASE KNOW ONCE ADDRESS HAS BEEN DETERMINED
	BY THE ADDRESSING REVIEWER THE NEW ADDRESS SHOULD BE
	PLACED ON THE TITLE BLOCKS.
	FBC ADMIN SECT 110.1.2, 106.1.2
	FAC 61G1-16.004, 61G15-23.002

	2) NOTE:THIS IS THE SAME COMMENT FROM PREVIOUS
	REVIEW.
	PLEASE SEE THE ARCHITECTURAL FIRM IS STILL MISSING THE
	REQUIRED LICENSE INFORMATION.
	** THIS IS REQUIRED. IF PLANS COME BACK WITHOUT THE
	REQUIRED INFORMATION THIS OFFICE WILL HAVE NO CHOICE
	BUT TO TURN THIS OVER TO THE STATE.
	PLEASE ADDRESS.
	PREVIOUS REVIEW NOTE
	PLEASE SEE MISSING LICENSE INFORMATION ON THE TITLE
	BLOCKS FOR THE ARCHITECTURAL FIRM.
	PLEASE KNOW THAT THE MISSING CERTIFICATE OF
	AUTHORIZATION AS REQUIRED FOR THE FIRM WHICH IS
	REQUIRED TO BE ON THE TITLE BLOCK IS IN FACT DELINQUENT
	WITH THE STATE. PLEASE SEE THE ATTACHED PRINT OUT FROM
	THE DEPARTMENT OF BUSINESS AND PROFESSIONAL REGULATION
	WHICH INDICATES THIS AS OF THIS REVIEW.
	PLEASE SEE FLORIDA ADMINISTRATIVE CODE 61G1-16.004 AND
	FLORIDA STATUTES 481.219
	** PLEASE KNOW THIS IS REQUIRED FOR ALL TRADES AND ALL
	SHEETS WHICH CONTAIN THIS TITLE BLOCK WHETHER OR NOT
	COMMENT IS MADE BY OTHER TRADE(S).

	3) NOTE: PLEASE SEE THE PLANS ARE NOW CONTAINING A NOTE
	WHICH MENTIONS THE ATS AND GENERATOR WILL BE UNDER
	SEPARATE PERMITS, HOWEVER PLEASE SEE THE PLANS AND
	RISER STILL INDICATE THE ATS BEIGN INSTALLED AT THIS
	TIME.
	IF ONLY THE ATS WILL BE INSTALLED AT THIS TIME WITH THE
	ELECTRICAL FOR THE MAIN HOUSE SERVICE, THEN PLEASE
	SUBMIT THE MANUFACTURES SPECS/CUT SHEETS FOR THIS
	UNIT.
	SOME OTHER SHEETS STILL SHOW THE GENERATOR.
	FBC 106.1.1, 106.1.2,
	NEC 110.3, 90.7

	4) NOTE: PLEASE SEE THE ARC FAULT PROTECTION NOTE ON
	THE BOTTOM OF THE PANEL SCHEDULE MENTIONS THIS IS
	REQUIRED FOR RECEPTACLE CIRCUITS HOWEVER THIS IS
	REQUIRED FOR ALL AS LISTED ON PREVIOUS REVIEW NOTE FOR
	ALLOUTLETS IN THE SLEEPING ROOMS INCLUSIVE OF SMOKE
	ALARMS, FANS, LIGHTING ETC.
	PLEASE SEE 210.12

	5) NOTE: PLEASE SEE THE REVISED ITEMS WERE NOT CLOUDED
	OR INDICATED ON THE PLANS. THE NOTES ON THE LOWER RIGHT
	HAND CORNER DO NOT ACTUALLY RESPOND TO ALL PREVIOUS
	NOTES.

	6) NOTE: PLEASE SEE NOTE #16 FROM PREVIOUS REVIEW WHICH
	REQUESTED FOR COMPLETION OF THE PANEL SCHEDULE TO SHOW
	THE REQUIRED MINIMUM BRANCH CIRCUIT CONDUCTORS, HOWEVER
	THIS WAS NOT DONE.
	PREVIOUS REVIEW NOTE
	PLEASE COMPLETE PANEL SCHEDULES WITH THE BRANCH
	CIRCUIT CONDUCTOR SIZES.
	408.4, 240.4, 310.16.
	FBC 106.1.2, 106.3.5.4

	7) NOTE:NO INFORMATION ON LIGHTING CONTROL
	PANEL(S)/SYSTEM AS NOTED ON PREVIOUS NOTE #17.
	PLEASE KNOW THAT ANY LIGHTING SYSTEMS OR CONTROLS WHICH
	ARE INSTALLED WHICH AFFECT THE BASE CODE DESIGNED BY
	THE DESIGNER OF RECORD WILL BE REQUIRED TO GO THROUGH
	THE RESPONSIBLE DESIGNER OF RECORD. THESE FUTURE
	PLANS WILL BE REQUIRED TO CONTAIN A SHOP DRAWING
	REVIEW STAMP IF PLANS ARE NOT DONE BY THE DESIGNER OF
	RECORD. PLEASE ALSO KNOW THAT ANY INSTALLATION OF THESE
	ITEMS WILL ALSO BE REQUIRED TO BE REVISED ON BASE HOUSE
	PLANS FOR REFERENCE OF SYSTEM.

	PREVIOUS REVIEW NOTE
	PLEASE SUBMIT MORE INFORMATION ON THE PROPOSED LIGHTING
	CONTROL PANELS AND SYSTEM. PLEASE SEE 110.3, 90.7 AS
	VERIFICATION OF THE TYPE OF SYSTEM, LISTING FROM A
	NRTL, LOCATIONS AND TYPE OF WIRING BEING INSTALLED.

	8) NOTE: PLEASE PROVIDE A NOTE ON PLANS FOR THE TYPE OF
	RECESSED LIGHTING AS REQUIRED PER FBC
	13-606-1.ABC.1.2.4.

	PLEASE KNOW THAT A TYPED WRITTEN RESPONSE WILL HELP IN
	THE REVIEW PROCESS. THIS IS NOT REQUIRED AND ONLY A
	SUGGESTION.
	PLEASE ALSO SEE THE PREVIOUS REVIEW WHICH MENTIONED IF
	THERE ARE ANY QUESTIONS OR COMMENTS TO PLEASE CONTACT
	THIS REVIEW.

	PLEASE SUBMIT THE ABOVE INFORMATION FOR REVIEW.

	* IMPORTANT
	ONCE ALL REVIEWS ARE DONE AND PLANS ARE PICKED UP FOR
	CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE ALL
	OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED SHEETS
	INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING. DO NOT
	LEAVE ANY OLD/VOIDED SHEETS IN SETS.
	PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS
	SHOULD BE SUBMITTED FOR REFERENCE.
	THIS WILL HELP IN THE REVIEW PROCESS AND AVOID ANY
	DELAYS.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW II
	CONSTRUCTION SERVICES DEPT.
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2007-08-31			Cont ID
Sent By	dpalmer			Date	2007-08-31	Time	10:20	Rev Time	0.00
Received By	dpalmer			Date	2007-08-29	Time	19:55	Sent To	M

Notes

2007-08-31 10:20:56	2007-08-31 10:20:56

	DENIED



	1) NOTE: PLEASE SEE THE ARCHITECTURAL PLANS DO NOT
	CONTAIN AN ORIGINAL SIGNATURE AND DATE AS REQUIRED PER
	FLORIDA STATUTES 481.221.
	THE PLANS ARE REQUIRED TO BE SIGNED AS ORIGINAL.
	PLACING A RAISED SEAL OVER AN IMAGED SIGNATURE IS NOT
	ACCEPTABLE PER THE MINIMUM REQUIREMENTS OF THE FAC AND
	FS.
	**THIS IS REQUIRED FOR ALL SHEETS AND ALL TRADES
	WHETHER OR NOT COMMENT IS MADE BY OTHER REVIEWS.

	2) NOTE: PLEASE SEE MISSING LICENSE INFORMATION ON THE
	TITLE BLOCKS FOR THE ARCHITECTURAL FIRM.
	PLEASE KNOW THAT THE MISSING CERTIFICATE OF
	AUTHORIZATION AS REQUIRED FOR THE FIRM WHICH IS
	REQUIRED TO BE ON THE TITLE BLOCK IS IN FACT DELINQUENT
	WITH THE STATE. PLEASE SEE THE ATTACHED PRINT OUT FROM
	THE DEPARTMENT OF BUSINESS AND PROFESSIONAL REGULATION
	WHICH INDICATES THIS AS OF THIS REVIEW.
	PLEASE SEE FLORIDA ADMINISTRATIVE CODE 61G1-16.004 AND
	FLORIDA STATUTES 481.219
	** PLEASE KNOW THIS IS REQUIRED FOR ALL TRADES AND ALL
	SHEETS WHICH CONTAINS THIS TITLE BLOCK WHETHER OR NOT
	COMMENT IS MADE BY OTHER TRADE(S).

	3) NOTE: PLEASE SEE THE TITLE BLOCK FOR THE ENGINEER
	AND FIRM AS SHOWN IS ALSO MISSING INFORMATION. PLEASE
	SEE THE MISSING PRINTED NAME, PRINTED LICENSE NUMBER
	AND MISSING CERTIFICATE OF AUTHORIZATION NUMBER.
	**PLEASE KNOW THIS IS REQUIRED FOR ALL MEP SHEETS
	WHETHER OR NOT COMMENT IS MADE BY OTHER TRADE(S).

	4) NOTE:PLEASE KNOW THAT ANY PERMIT APPLICATIONS
	WHICH ARE SUBMITTED AFTER DECEMBER 8TH, 2006 PLACES
	PROJECTS UNDER THE NEW CODES ADOPTED BY THE STATE.
	PLEASE SEE THAT THIS SHALL INCLUDE 2006 REVISIONS TO
	THE 2004 FBC FOR ALL TRADES AND THE 2005 NFPA-70.
	PLEASE KNOW THERE ARE CHANGES IN THE FBC WHICH MAY
	AFFECT DESIGNS FOR ALL TRADES.
	PLEASE LIST THE FOLLOWING ON ELECTRICAL SHEETS FOR THIS
	REVIEWER AT A MINIMUM.
	2004 FBC W/ 2006 REVISIONS
	2005 NFPA-70
	2002 NFPA-72
	2003 NFPA-101


	5) NOTE: PLEASE SEE THE PLANS ARE SHOWING A NEW
	GENERATOR AND ATS BEING INCLUDED WITH THE SCOPE OF WORK
	FOR HOUSE HOWEVER PLEASE SUBMIT THE MANUFACTURES
	SPEC/CUT SHEETS FOR BOTH.IF THE GENERATOR WILL BE
	UNDER A SEPARATE PERMIT PLEASE ADJUST PLANS TO INDICATE
	THIS.
	PLEASE KNOW THE GENERATOR SPECS/CUT SHEETS ARE TO
	INDICATE THE MINIMUM CLEARANCES FOR UNIT.
	PLEASE SUBMIT AND SEE COMMENTS FROM OTHER TRADES FROM
	ZONING, BUILDING AND PLUMBING.
	FBC 106.1.1, 106.1.2,
	NEC 110.3, 90.7

	6) NOTE: PLEASE SEE THERE ARE SEVERAL SPECIFIC
	DEDICATED APPLIANCE LOADS AND MOTORS LOADS ON THE
	ELECTRICAL PANEL SCHEDULES WHERE THE LOADS ARE NOT
	INCLUDED IN THE LOAD CALCULATIONS.
	PLEASE GO OVER CALCULATIONS AND ADJUST AS NEEDED.
	PLEASE SEE FOR EXAMPLE MISSING, WATER PUMP,
	REFRIGERATOR, WASHER, CENTRAL VACUUM, GARAGE DOOR
	OPENER ETC.
	PLEASE SEE NEC 220 AND SEE SOME COMMENTS BELOW FOR SOME
	OTHER LOADS.

	7) NOTE:PLEASE SEE 210. 52C2 AND 220.53 FOR MINIMUM
	LOADS FOR THE WASHER/LAUNDRY LOADS AS REQUIRED. PLEASE
	SEE THE PANEL SCHEDULE DOES NOT INDICATE THE MINIMUM OF
	1500VA FOR EACH OF THESE AS SHOWN AND LISTED. PLEASE
	ALSO SEE THE LOADS SHOWN ON THE LOAD CALCULATIONS ON
	THE SERVICE INDICATE (2) LAUNDRY LOADS HOWEVER THE TWO
	ARE SHOWN WITH A TOTAL OF 4500VA?
	IT IS UNCLEAR HOW THESE LOADS ARE BEING DETERMINED AS
	THE PANEL SCHEDULE AND OTHER LOADS ARE NOT THE SAME.
	PLEASE SEE THE SECTIONS AS NOTED FOR THE MINIMUM
	LOADS.
	PLEASE ADJUST.

	8) NOTE: PLEASE SEE MISSING ARC FAULT PROTECTION FRO
	ALL OUTLETS IN THE SLEEPING ROOMS INCLUSIVE OF SMOKE
	ALARMS, FANS, LIGHTING ETC.
	PLEASE SEE 210.12

	9) NOTE: PLEASE SEE MINIMUM LOADS TO BE FIGURED FOR
	RECESSED LIGHTING. PLEASE SEE THAT THE WATTAGE BASED ON
	THE AMOUNT OF EACH OF THESE TYPES OF FIXTURES DO EXCEED
	THE 3VA PER SQ FT.THIS WAS CONFIRMED BY THE CODE
	PANELIST AND THE AHJ IS THE DETERMINING AUTHORITY.
	PLEASE SEE THE FOLLOWING TEXT WHICH IS TAKEN DIRECTLY
	FROM THE 2005 NEC AND SOME COMMENTARY FROM THE
	HANDBOOK.

	*D) LUMINAIRES (LIGHTING FIXTURES) AN OUTLET SUPPLYING
	LUMINAIRE(S) [LIGHTING FIXTURE(S)] SHALL BE CALCULATED
	BASED ON THE MAXIMUM VOLT-AMPERE RATING OF THE
	EQUIPMENT AND LAMPS FOR WHICH THE LUMINAIRE(S)
	[FIXTURE(S)] IS RATED.
	IN GENERAL, NO ADDITIONAL CALCULATION IS REQUIRED FOR
	LUMINAIRES (RECESSED AND SURFACE MOUNTED) INSTALLED IN
	OR ON A DWELLING UNIT, BECAUSE THE LOAD OF SUCH
	LUMINAIRES IS COVERED IN THE 3 VOLT-AMPERES PER SQUARE
	FOOT CALCULATION SPECIFIED BY TABLE 220.12. WHERE THE
	RATING OF THE LUMINAIRES INSTALLED FOR GENERAL LIGHTING
	EXCEEDS THE MINIMUM LOAD PROVIDED FOR IN TABLE 220.12,
	THE MINIMUM GENERAL LIGHTING LOAD FOR THAT PREMISES IS
	TO BE BASED ON THE INSTALLED LUMINAIRES. DISTINGUISHING
	BETWEEN THE LUMINAIRES INSTALLED FOR GENERAL LIGHTING
	VERSUS THOSE INSTALLED FOR ACCENT, SPECIALTY OR DISPLAY
	LIGHTING IS MUCH EASIER TO DELINEATE IN COMMERCIAL
	(PARTICULARLY MERCANTILE) OCCUPANCIES.

	AS STATED, IN GENERAL AN ADDITIONAL AMOUNT IS NOT
	NEEDED ONLY WHEN THE FIXTURES ARE USED FOR NORMAL
	GENERAL LIGHTING. WHEN THE FIXTURES EXCEED THE GENERAL
	LIGHTING USE AS THIS IS DONE ON THIS PLAN, THEN THE
	ADDITIONAL SHALL BE FIGURED.
	PLEASE SEE THIS SECTION IN THE 2002 NEC WAS 220.3B4

	10) NOTE: PLEASE SEE NFPA-72 FOR DEFINITIONS FOR SMOKE
	DETECTION DEVICES.PLEASE SEE THAT SMOKE DETECTORS ARE
	DEVICES WHICH ONLY DETECT AND DO NOT SOUND AND ALARM
	WHEREAS SMOKE ALARMS ARE DEVICES WHICH DETECT AND SOUND
	AN ALARM.
	AS THE PLAN INDICATES SD FOR SMOKE DETECTORS THIS SEEMS
	IT SHOULD BE SA FOR SMOKE ALARMS.
	PLEASE SEE THE 2002 NFPA-72

	11) NOTE: PLEASE SEE THE PLANS DO NOT SHOW ANY OF THE
	MAINS AS SHOWN ON RISER ON THE OUTSIDE OF THE HOUSE.
	ONLY THE METER AND ATS IS SHOWN.
	PLEASE COORDINATE.
	FBC 106.1.2

	12) NOTE: PLEASE SEE THE POOL PANEL DOES NOT MEET THE
	MINIMUM CLEARANCE REQUIREMENTS PER 110.26.

	13) NOTE: PLEASE SEE THE HOT WATER HEATERS ARE BEING
	SHOWN AS CONNECTED BY MEANS OF RECEPTACLES WHICH ARE
	NOT PERMITTED.
	PLEASE SEE 422.30, 422.31.
	PLEASE INDICATE ON PLANS.

	14) NOTE: PLEASE SEE 422.13 AS THE LOADS FOR THE WATER
	HEATERS ARE TO BE FIGURED AT 125% FOR CONTINUOUS
	LOADS.
	THIS WAS REVISED IN THE 2005 NEC AND PLEASE SEE CODE
	COMMENTARY IN THE NEC HANDBOOK.

	15) NOTE: PLEASE GO OVER FIXTURES AND LOCATIONS IN ALL
	STORAGE CLOSETS FOR MINIMUM CLEARANCES FOR FIXTURES
	FROM CLOSET SHELVING PER 410.8
	PLEASE SEE THERE ARE SOME ON PLANS WHICH AS SHOWN ARE
	TOO CLOSE TO SHELVES.

	16) NOTE: PLEASE COMPLETE PANEL SCHEDULES WITH THE
	BRANCH CIRCUIT CONDUCTOR SIZES.
	408.4, 240.4, 310.16.
	FBC 106.1.2, 106.3.5.4

	17) NOTE: PLEASE SUBMIT MORE INFORMATION ON THE
	PROPOSED LIGHTING CONTROL PANELS AND SYSTEM. PLEASE SEE
	110.3, 90.7 AS VERIFICATION OF THE TYPE OF SYSTEM,
	LISTING FROM A NRTL, LOCATIONS AND TYPE OF WIRING BEING
	INSTALLED.

	18) NOTE: PLEASE SEE SOME 3-WAY SWITCHING LOCATIONS ARE
	SHOWING A S3, (3-WAY DEVICE AT EITHER END WHICH IS OK,
	HOWEVER PLEASE CLARIFY THAT BOTH ENDS ARE SHOWN AS
	BEING DIMMERS?
	IN 3-WAY AND OR 4-WAY WIRING SYSTEMS THE DIMMERS ARE
	TYPICALLY ONLY AT ONE LOCATION BASED ON STANDARD
	DEVICES WHICH IS WHAT IS BEING SHOWN.
	PLEASE SEE THE NOTE #16 ABOVE AS THESE MAY BE A PART OF
	THE LIGHTING CONTROL SYSTEM WHICH IS NOT KNOWN AT THIS
	TIME.

	19) NOTE: PLEASE SEE THE LOADS FOR THE AIR HANDLERS ARE
	IN QUESTION. THE A/C DETAILS INDICATE LOADS IN KW WHICH
	ARE SUBSTANTIALLY HIGHER THAN THAT OF THE LOAD SHOWN ON
	THE LOAD CALCULATIONS.
	PLEASE SEE 220.60 AS THE LARGER OF THE HEATING AND
	COOLING LOADS ARE TO BE FIGURED.

	20) NOTE: PLEASE KNOW AS FOR INFORMATION THE LOW
	VOLTAGE AS SHOWN ON PLANS WILL BE REQUIRED TO BE UNDER
	SEPARATE PERMITS. THESE PLANS WHICH CONTAIN ITEMS FOR
	MANY LV ITEMS MAY BE USED AS A REFERENCE FOR TURN
	AROUND PERMITS HOWEVER SEPARATE APPLICATION AND FEES
	WILL BE DUE BASED ON THE SEPARATE VALUATIONS OF THESE
	SYSTEMS.
	*ANY LOW VOLTAGE SECURITY IS ALSO UNDER A SEPARATE
	PERMIT. THESE DO NOT NEED PLANS UNLESS CAMERA OR ACCESS
	CONTROL SYSTEMS ARE BEING INSTALLED. THE DEVICE
	LOCATIONS INCLUDING THE LOCATION OF SECURITY PANELS DO
	NOTNEED TO BE INCLUDED ON ANY PANELS.
	THE LV FOR ALARM SYSTEMS IS UNDER SEPARATE FEES BASED
	ON THAT SCOPE OF WORK.
	THIS IS ONLY NOTED FOR INFORMATION AND NO INFORMATION
	AND CHANGES NEED TO BE MADE ON PLANS.
	** IF THERE IS ANY CLARIFICATION NEEDED PLEASE CONTACT
	THIS OFFICE/REVIEWER.

	21) NOTE: PLEASE SEE THE PLANS INDICATE THE RECEPTACLE
	BEING NOTED FOR THE WINE COOLER (MAIN) BEING CIRCUITED
	TO OTHER GENERAL PURPOSE RECEPTACLES IN THE DWELLING.
	PLEASE CLARIFY THIS AS SHOWN.
	PLEASE VERIFY LOAD AND PROVIDE INFORMATION FOR ANY
	CHANGES WITH ANY MOTOR LOADS ON THE GENERAL PURPOSE
	BRANCH RECEPTACLES.
	FBC 106.1.2.
	430.6 AND SEVERAL OTHER CODES IN 430 FOR INFORMATION
	INCLUDING 430.148

	22) NOTE: PLEASE SEE THE A/C CLOSET DETAILS ON SHEET
	FOR SECOND FLOOR. THE DISCONNECT SHOWN FOR ONE O OF THE
	AIR HANDLER UNITS DO NOT SEEM TO MEET 110.26.

	23) NOTE: PLEASE SEE THE PLANS NOTES *BREAKER LOCK
	DEVICES* FOR SMOKE ALARMS.
	PLEASE KNOW AS NOTED ABOVE THESE REQUIRE ARC FAULT
	PROTECTION REQUIRED, THESE SMOKE DEVICES MAY BE PLACED
	ON THE LIGHTING/RECEPTACLE CIRCUITS FOR BEDROOMS.

	24) NOTE: PLEASE PROVIDE A NOTE ON PLANS FOR THE TYPE
	OF RECESSED LIGHTING AS REQUIRED PER FBC
	13-606-1.ABC.1.2.4.

	** PLEASE SEE ANY COMMENTS FROM OTHER TRADES WHICH MAY
	OR MAY NOT AFFECT ELECTRICAL PLANS.



	PLEASE BE SURE TO CALL IF THERE ARE ANY QUESTIONS OR
	COMMENTS WITH RESPECT TO THE TYPED COMMENTS ABOVE. IF
	THERE ARE ANY COMMENTS WHICH ARE NOT CLEAR IN ANY WAY,
	NOT UNDERSTOOD OR NOT TYPED IN A CLEAR MANOR, PLEASE DO
	NOT HESITATE IN CONTACTING THIS OFFICE AND THIS
	REVIEWER.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW II
	CONSTRUCTION SERVICES DEPT.
	CITY OF WEST PALM BEACH
	561-805-6717
	[email protected]
2007-08-31 07:58:21	2007-08-31 07:58:21

	REVIEW CONTINUED
2007-08-29 20:50:20	2007-08-29 20:50:20

	ELECTRICAL REVIEW WILL BE PROCESSED INTO A F STATUS
	AND NOTES WILL FOLLOW ONCE REVIEW IS COMPLETED ON 8/30
2007-08-29 19:55:58	2007-08-29 19:55:58
	IN ELEC FOR REVIEW

Review Stop	I			INCOMING/PROCESSING
Rev No	14	Status	N	Date	2009-09-22			Cont ID
Sent By	lmartine			Date	2009-09-17	Time	10:59	Rev Time	0.00
Received By	lmartine			Date	2009-09-17	Time	10:59	Sent To

Notes

2009-09-22 11:00:40

GAVE TO DEWEY, ROUTED ON 9/22 LM

Review Stop	I			INCOMING/PROCESSING
Rev No	13	Status	N	Date	2009-07-15			Cont ID
Sent By	shill			Date	2009-07-15	Time	08:55	Rev Time	0.00
Received By	shill			Date	2009-07-15	Time	08:55	Sent To

Notes

2009-07-15 08:55:25

TO DP DESK

Review Stop	I			INCOMING/PROCESSING
Rev No	12	Status	N	Date	2009-04-20			Cont ID
Sent By	shill			Date	2009-04-20	Time	11:37	Rev Time	0.00
Received By	shill			Date	2009-04-20	Time	11:37	Sent To

Notes

2009-04-20 11:37:48

TO RM DESK

Review Stop	I			INCOMING/PROCESSING
Rev No	11	Status	N	Date	2009-04-10			Cont ID
Sent By	adarroug			Date	2009-04-10	Time	13:04	Rev Time	0.00
Received By	adarroug			Date	2009-04-10	Time	13:04	Sent To	B

Notes

2009-04-10 13:04:45

TO "RMCDOUGAL" DESK/REV

Review Stop	I			INCOMING/PROCESSING
Rev No	10	Status	N	Date	2008-09-23			Cont ID
Sent By	adarroug			Date	2008-09-23	Time	15:43	Rev Time	0.00
Received By	adarroug			Date	2008-09-23	Time	15:43	Sent To	M

Notes

2008-09-23 15:43:54

TO "M" BOX/REV

Review Stop	I			INCOMING/PROCESSING
Rev No	9	Status	N	Date	2008-04-02			Cont ID
Sent By	adarroug			Date	2008-04-02	Time	14:11	Rev Time	0.00
Received By	adarroug			Date	2008-04-02	Time	14:11	Sent To	P

Notes

2008-04-02 14:12:27

TO "P" BOX/REV

Review Stop	I			INCOMING/PROCESSING
Rev No	8	Status	N	Date	2008-03-26			Cont ID
Sent By	adarroug			Date	2008-03-26	Time	13:53	Rev Time	0.00
Received By	adarroug			Date	2008-03-26	Time	13:53	Sent To	P

Notes

2008-03-26 13:54:05

TO "P" BOX/REV

Review Stop	I			INCOMING/PROCESSING
Rev No	7	Status	N	Date	2008-02-06			Cont ID
Sent By	adarroug			Date	2008-02-06	Time	11:10	Rev Time	0.00
Received By	adarroug			Date	2008-02-06	Time	11:10	Sent To	B

Notes

2008-02-06 11:10:33

TO "RMCDOUGAL" DESK/SUBMITTAL

Review Stop	I			INCOMING/PROCESSING
Rev No	6	Status	N	Date	2008-01-29			Cont ID
Sent By	adarroug			Date	2008-01-29	Time	08:31	Rev Time	0.00
Received By	adarroug			Date	2008-01-29	Time	08:31	Sent To	M

Notes

2008-01-29 08:31:35

TO "M" BOX/RESUB

Review Stop	I			INCOMING/PROCESSING
Rev No	5	Status	N	Date	2008-01-11			Cont ID
Sent By	spalmer			Date	2008-01-11	Time		Rev Time	0.00
Received By	spalmer			Date	2008-01-11	Time	10:32	Sent To	M

Notes

2008-01-11 10:33:24

TO TOM GORDONS DESK

Review Stop	I			INCOMING/PROCESSING
Rev No	4	Status	N	Date	2008-01-10			Cont ID
Sent By	mmiller			Date	2008-01-10	Time	19:09	Rev Time	0.00
Received By	mmiller			Date	2008-01-10	Time	19:09	Sent To

Notes

2008-01-10 19:10:18

NEED TO SPEAK WITH DEWEY PALMER REGARDING THESE PLANS

Review Stop	I			INCOMING/PROCESSING
Rev No	3	Status	N	Date	2007-11-30			Cont ID
Sent By	adarroug			Date	2007-11-30	Time	14:38	Rev Time	0.00
Received By	adarroug			Date	2007-11-30	Time	14:38	Sent To	Z

Notes

2007-11-30 14:38:42

TO "Z" BOX/RESUB

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2007-10-02			Cont ID
Sent By	adarroug			Date	2007-10-02	Time	10:37	Rev Time	0.00
Received By	adarroug			Date	2007-10-02	Time	10:37	Sent To	Z

Notes

2007-10-02 10:37:51

TO "Z" BOX/RESUB

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2007-09-18			Cont ID
Sent By	rmcdouga			Date	2007-09-18	Time	14:45	Rev Time	0.00
Received By	rmcdouga			Date	2007-08-22	Time	16:14	Sent To

Notes

2007-08-22 16:14:53

TO "SFR" "Z"

Review Stop	M			MECHANICAL (A/C)
Rev No	6	Status	P	Date	2008-09-25			Cont ID
Sent By	tgordon			Date	2008-09-25	Time	15:26	Rev Time	0.45
Received By	tgordon			Date	2008-09-25	Time	15:26	Sent To

Notes

2008-09-25 15:27:35

RVISION TO MECH. PLANS M-1 AND M-2.

Review Stop	M			MECHANICAL (A/C)
Rev No	5	Status	P	Date	2008-01-29			Cont ID
Sent By	tgordon			Date	2008-01-29	Time	09:21	Rev Time	0.45
Received By	tgordon			Date	2008-01-29	Time	09:21	Sent To	B

Notes

***NONE***

Review Stop	M			MECHANICAL (A/C)
Rev No	4	Status	F	Date	2008-01-11			Cont ID
Sent By	tgordon			Date	2008-01-11	Time	13:41	Rev Time	1.30
Received By	tgordon			Date	2008-01-11	Time	13:41	Sent To	B

Notes

2008-01-11 14:04:27	PLAN REVIEW UNDER THE 2004 FLORIDA BUILDING CODE &
	REFERENCED CODES WITH 2007 REVISIONS, CITY OF WEST PALM
	BEACH AMENDMENTS TO CHAPTER 1 (W.P.B.), FLORIDA
	ADMINISTRATIVE CODE (F.A.C.), AND FLORIDA STATUTES
	(F.S.).

	* DENIED *
	1) ONLY ONE SET OF THE MECHANICAL PLANS PAGE M-1 AND
	M-2 WERE SUBMITTED FOR REVIEW, TWO SETS MUST BE
	SUBMITTED, SEE 2004 FBC/WPB AMEND. 106.1.

	2) COOLING LOAD CALCULATIONS ARE CALLING FOR 121,173
	TOTAL COOLING BTU'S, MECHANICAL PLANS ARE SHOWING
	156,400 TOTAL COOLING BTU'S, THE PLANS CAN ONLY CALL
	FOR 15% MORE THAN THE COOLING LOAD CALCULATIONS, SEE
	2004 FBC 13-607.1.ABC.1.1. 13 TONS OF AIR CONDITIONING
	APPEARS TO BE TO MUCH, PLEASE CORRECT.

	3) A/C SYSTEM 1 AND 2 ARI CERTIFICATION HAS BEEN
	DISCONTINUED (SEE ATTACHED COPY), SEE 2004 FBC
	13-607.1.ABC.3.1.1, PLEASE CORRECT.

	4) THE FIRST FLOOR CLOTHES DRYER VENT MAY NOT DISCHARGE
	ON OR TERMINATE NEAR THE A/C CONDENSER UNIT, SEE 2004
	FBC/R M303.4.2, PLEASE CORRECT.

	5) PLEASE ADD JOB ADDRESS TO ANY NEW MECHANICAL PLANS,
	SEE 2004 FBC/WPB AMEND. 106.1.3.

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729
	E-MAIL; [email protected] .

Review Stop	M			MECHANICAL (A/C)
Rev No	3	Status	F	Date	2007-12-03			Cont ID
Sent By	tgordon			Date	2007-12-03	Time	14:58	Rev Time	0.30
Received By	tgordon			Date	2007-12-03	Time	14:57	Sent To	P

Notes

2007-12-03 15:03:00	PLAN REVIEW UNDER THE 2004 FLORIDA BUILDING CODE &
	REFERENCED CODES WITH 2007 REVISIONS, CITY OF WEST PALM
	BEACH AMENDMENTS TO CHAPTER 1 (W.P.B.), FLORIDA
	ADMINISTRATIVE CODE (F.A.C.), AND FLORIDA STATUTES
	(F.S.).

	* DENIED *
	1) COMPLETE MECHANICAL REVIEW COULD NOT BE DONE AS
	MECHANICAL PLANS PAGES M.1 AND M.2 WERE NOT SUBMITTED
	WITH REVISED PLANS. SEE 2004 W.P.B AMEND. 106.3.5.4
	(10) SUBMIT MECHANICAL PLANS FOR REVIEW.

	2) ENERGY CALCULATIONS NEED TO BE SIGNED BY OWNER/AGENT
	ALSO, PER 2004 FBC 13-600.3.ABC.2.

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729
	E-MAIL; [email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2007-10-10			Cont ID
Sent By	tgordon			Date	2007-10-10	Time	12:06	Rev Time	0.45
Received By	tgordon			Date	2007-10-10	Time	12:06	Sent To	P

Notes

2007-10-10 12:29:56	PLAN REVIEW UNDER THE 2004 FLORIDA BUILDING CODE &
	REFERENCED CODES WITH 05, 06 REVISIONS, CITY OF WEST
	PALM BEACH AMENDMENTS TO CHAPTER 1 (WPB), FLORIDA
	ADMINISTRATIVE CODE (FAC), AND FLORIDA STATUTES (FS).

	* DENIED *

	1) AS NOTED IN LAST REVIEW 9/6/07. MECHANICAL PLANS,
	INFORMATION MISSING IN TITLE BLOCK FOR ARCHITECT
	(ARCHITECT FIRM LICENSE NUMBER AA0002936).
	PER FAC 61G1-16.004 TITLE BLOCK.

	2) AS NOTED IN LAST REVIEW 9/6/07 NOTE #3. PLEASE
	SUBMIT COOLING LOAD CALCULATIONS, SEE FBC
	13-407.1.ABC.1.

	3) AS NOTED IN LAST REVIEW 9/6/07 NOTE #4. ENERGY
	CALCULATIONS LINE 13A, AND B SHOW THE A/C SYSTEMS AS
	HEAT PUMP SYSTEMS. THE ARI DIRECTORY SHOWS THE UNITS
	ARE STRAIGHT COOL SYSTEMS, PLEASE CORRECT ENERGY CAL'S.
	OR MODEL NUMBERS ON MECHANICAL PLANS.

	4) AS NOTED IN LAST REVIEW 9/6/07 NOTE #6. PLEASE
	SUBMIT DETAILED MANUFACTURER'S SPECIFICATION'S AND
	INSTALLATION INSTRUCTIONS FOR THE GAS BBQ GRILL AND
	HOOD, GAS FIRE PLACES, AND GAS LOG LIGHTERS IF USED.

	5) AS NOTED IN LAST REVIEW NOTE #7. PLEASE SUBMIT
	PRODUCT APPROVAL FOR O/A LOUVER FOR SAFE ROOM, SEE FS
	553.842(1) AND FAC RULE 9B-72, 9B-72.005, AND FAC
	9B-72.010(31)(G).

	**PRODUCT APPROVALS SUBMITTED WITH PERMIT APPLICATION
	AFTER OCTOBER 1, 2003 ARE REQUIRED TO COMPLY WITH THE
	FLORIDA PRODUCT APPROVAL SYSTEM. FOR INFORMATION PLEASE
	SEE THE STATE WEBSITE AT WWW.FLORIDABUILDING.ORG.
	PRODUCTS WITH STATEWIDE APPROVAL ARE REQUIRED TO BE
	SUBMITTED WITH A COVER SHEET THAT LISTS THE PRODUCT
	IDENTITY NUMBER FROM THE STATE. IF THE PRODUCT DOES NOT
	HAVE STATEWIDE APPROVAL, SUBMIT AN APPLICATION FOR
	LOCAL PRODUCT APPROVAL OR SITE SPECIFIC FORM PER RULE
	9B-72. SEE ATTACHMENT. WWW.FLORIDABUILDING.ORG.

	6) WASHER/DRYER DETAIL ON PAGE DMP-1 STATES PER I.M.C.
	2003304.6.1. ALL WORK PERMITTED IN THE CITY OF W.P.B.
	MUST COMPLY WITH THE "2004 F.B.C.", PLEASE CORRECT.

	7) SEE ATTACHED NOTICE FS 553.80 (2) (B) REGARDING FOUR
	TIMES THE FEE.

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729
	E-MAIL; [email protected]

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2007-09-06			Cont ID
Sent By	tgordon			Date	2007-09-06	Time	08:43	Rev Time	1.30
Received By	tgordon			Date	2007-09-06	Time	08:43	Sent To	P

Notes

2007-09-06 09:33:01	PLAN REVIEW UNDER THE 2004 FLORIDA BUILDING CODE &
	REFERENCED CODES WITH 05, 06 REVISIONS, CITY OF WEST
	PALM BEACH AMENDMENTS TO CHAPTER 1 (WPB), FLORIDA
	ADMINISTRATIVE CODE (FAC), AND FLORIDA STATUTES (FS).

	* DENIED *
	1) MECHANICAL PLANS, INFORMATION MISSING FROM TITLE
	BLOCK (ENGINEERS PRINTED NAME AND LICENSE NUMBER WHO
	SEALED THE PLAN, AND THE ENGINEERING BUSINESS
	CERTIFICATE OF AUTHORIZATION NUMBER).
	SEE FAC 61G15-23.002 (2)A TITLE BLOCK ON EACH SHEET
	CONTAINING THE PRINTED NAME, ADDRESS, AND LICENSE
	NUMBER OF THE ENGINEER OR IF APPLICABLE, THE NAME AND
	LICENSE NUMBER OF THE ENGINEER, AND THE NAME, ADDRESS
	AND CERTIFICATE OF AUTHORIZATION NUMBER OF THE
	ENGINEERING BUSINESS WILL SATISFY THIS REQUIREMENT.

	2) MECHANICAL PLANS, INFORMATION MISSING IN TITLE BLOCK
	FOR ARCHITECT (ARCHITECT FIRM LICENSE NUMBER, AND JOB
	ADDRESS).
	SEE FAC 61G1-16.004 TITLE BLOCK. A TITLE BLOCK MUST
	APPEAR ON ALL ARCHITECTURAL OR INTERIOR DESIGN DRAWINGS
	AND SPECIFICATION IDENTIFICATION SHEETS. THE TITLE
	BLOCK MUST, AT A MINIMUM, CONTAIN THE FOLLOWING
	INFORMATION:
	(1) FIRM NAME, ADDRESS, AND TELEPHONE NUMBER.
	(2) FIRM LICENSE NUMBER.
	(3) NAME OR IDENTIFICATION OF PROJECT. ("JOB ADDRESS"
	SEE CITY WPB AMEND. 106.1.1).
	(4) DATE PREPARED.
	(5) A SPACE FOR THE SIGNATURE AND DATED SEAL.
	(6) A SPACE FOR THE PRINTED NAME OF THE PERSON SEALING
	THE DOCUMENT.

	3) PLEASE SUBMIT COOLING LOAD CALCULATIONS, SEE FBC
	13-407.1.ABC.1.

	4) ENERGY CALCULATIONS LINE 13A, AND B SHOW THE A/C
	SYSTEMS AS HEAT PUMP SYSTEMS. THE ARI DIRECTORY SHOWS
	THE UNITS ARE STRAIGHT COOL SYSTEMS, PLEASE CORRECT
	ENERGY CAL'S. OR MODEL NUMBERS ON MECHANICAL PLANS.

	4) PAGE DMP-1 DETAIL OF CONDENSATE DISCHARGE TO GRADE,
	DRAIN NEEDS TO DISCHARGE 12" FROM THE BUILDING, SEE
	RES. R320.7. PLEASE CORRECT.

	5) PAGES M-1 AND M-2 DUCT SCHEDULE ZONES 2, 3, AND 4 DO
	NOT SHOW ALL THE DUCT SIZES (SEE YELLOW HIGH LIGHT ON
	PLAN) PLEASE CORRECT.

	6) PLEASE SUBMIT DETAILED MANUFACTURER'S
	SPECIFICATION'S AND INSTALLATION INSTRUCTIONS FOR THE
	GAS BBQ GRILL AND HOOD, GAS FIRE PLACES, AND GAS LOG
	LIGHTERS IF USED.

	7) PLEASE SUBMIT PRODUCT APPROVAL FOR O/A LOUVER FOR
	SAFE ROOM, SEE FS 553.842(1) AND FAC RULE 9B-72,
	9B-72.005, AND FAC 9B-72.010(31)(G).

	**PRODUCT APPROVALS SUBMITTED WITH PERMIT APPLICATION
	AFTER OCTOBER 1, 2003 ARE REQUIRED TO COMPLY WITH THE
	FLORIDA PRODUCT APPROVAL SYSTEM. FOR INFORMATION PLEASE
	SEE THE STATE WEBSITE AT WWW.FLORIDABUILDING.ORG.
	PRODUCTS WITH STATEWIDE APPROVAL ARE REQUIRED TO BE
	SUBMITTED WITH A COVER SHEET THAT LISTS THE PRODUCT
	IDENTITY NUMBER FROM THE STATE. IF THE PRODUCT DOES NOT
	HAVE STATEWIDE APPROVAL, SUBMIT AN APPLICATION FOR
	LOCAL PRODUCT APPROVAL OR SITE SPECIFIC FORM PER RULE
	9B-72. SEE ATTACHMENT. WWW.FLORIDABUILDING.ORG.

	*** INFORNATIONAL: PAGE A.01 SHOWS A GENERATOR NEAR A
	8X8" VENT BLOCK TO THE GARAGE NFPA 37 REQUIRES
	GENERATORS TO BE FIVE FEET FROM BUILDING OPENINGS.

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729
	E-MAIL; [email protected]

Review Stop	P			PLUMBING
Rev No	5	Status	P	Date	2008-04-14			Cont ID
Sent By	jleech			Date	2008-04-14	Time	08:10	Rev Time	0.00
Received By	jleech			Date	2008-04-14	Time	08:00	Sent To

Notes

2008-04-14 08:11:06

PLUMBING AS-BUILTS

Review Stop	P			PLUMBING
Rev No	4	Status	F	Date	2008-03-27			Cont ID
Sent By	mperson			Date	2008-03-27	Time	10:22	Rev Time	0.00
Received By	mperson			Date	2008-03-27	Time	10:22	Sent To	PC

Notes

2008-03-27 10:29:55	PLUMBING PLAN REVIEW:
	REVISION DENIED:

	PLAN REVIEW UNDER THE 2004 FLORIDA BUILDING CODES WITH
	2007 REVISIONS, CITY OF WEST PALM BEACH AMENDMENTS TO
	CHAPTER 1 (W.P.B.), FLORIDA ADMINISTRATIVE CODE
	(F.A.C.), AND FLORIDA STATUTES (F.S.).

	1. SHEET P.01 MASTER BATH SANITARY PLUMBING RISER: THE
	BIDET IS NOT VENTED. PER FBC PLUMBING SECTION 901.2.1
	VENTING REQUIRED.

	******IMPORTANT INFORMATION******
	WHEN RESUBMITTING PLANS, PLEASE INDICATE THE REVISION
	AND REMOVE & REPLACE ANY PAGES AS NECESSARY. A
	TRANSMITTAL LETTER LISTING THE ORIGINAL REVIEW COMMENT
	NUMBER, WITH A DESCRIPTION OF THE REVISION MADE,
	IDENTIFYING THE SHEET OR SPECIFICATION PAGE WHERE
	CHANGES CAN BE FOUND WILL HELP TO EXPEDITE YOUR PERMIT.
	THANK YOU FOR YOUR ANTICIPATED COOPERATION.
	NOTE: THERE IS ONLY ONE CORRECTED DRAWING
	IN RED INK ON THE INDICATED PLAN SHEETS BY THIS PLANS
	EXAMINER FOR REFERENCE FOR THE
	RESUBMITTAL.

	END OF COMMENTS:

	REVIEW BY: MIKE PERSON
	PLUMBING PLANS EXAMINER
	PHONE= (561) 805-6730
	FAX= (561) 805-6731
	E-MAIL= [email protected]

Review Stop	P			PLUMBING
Rev No	3	Status	P	Date	2007-12-14			Cont ID
Sent By	jleech			Date	2007-12-14	Time	09:52	Rev Time	0.00
Received By	jleech			Date	2007-12-14	Time	08:33	Sent To	B

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	2	Status	F	Date	2007-10-16			Cont ID
Sent By	jleech			Date	2007-10-16	Time	08:31	Rev Time	0.00
Received By	jleech			Date	2007-10-16	Time	08:01	Sent To	B

Notes

2007-10-16 08:51:55	DENIED;
	1.SEE MECHANICAL NOTE #1. ARCHITECT FIRM LICENSE IS
	REQUIRED ON THE TITLE BLOCK.
	2. SANITARY RISER DIAGRAM, CLEANOUT'S REQUIRED ON
	AUTOMATIC CLOTHES WASHER VENT AT 48" ABOVE FINISH
	FLOOR.
	3. DISHWASHERS TO DISCHARGE INDIRECTLY INTO BUILDING
	DRAIN. SECTION 802.1.6.
	4. 1/2 BATH FIRST FLOOR TOILET NOT VENTED AS DRAWN
	CANNOT DISCHARGE INTO THE 2ND FLOOR BRANCH DRAIN.
	5. WATER SANITARY RISER DIAGRAM WATER HAMMER ARRESTORS
	ARE REQUIRED ON ALL QUICK CLOSING VALVES PER 604.9 SHOW
	ON PLANS.
	6. 2 WATER HEATERS SHOWN ON FLOOR PLANS 80 GAL ON 1ST
	FLOOR60 GAL ON 2ND FLOOR, ONLY ONE MODEL # SHOWN ON
	PAGE DMP-1.
	7. SHOW LOCATION OF IN-LINE PUMP FOR MATER SHOWER. THIS
	PUMP MUST BE ACCESSABLE WITH A SHUTOFF VALVE UP STREAM.

	PLUMBING PLAN REVIEW BY
	JOHN LEECH
	805-6695

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2007-09-11			Cont ID
Sent By	jleech			Date	2007-09-11	Time	08:50	Rev Time	0.00
Received By	jleech			Date	2007-09-11	Time	08:24	Sent To	B

Notes

2007-09-11 09:11:09	DENIED;
	SEE ELECTRICAL PLAN REVIEW NOTES 1 THRU 5.
	1.SHOW ON PLANS, BACKFLOW PREVENTOR REQUIRED. CITY
	UTILITY ORD. RPZ REQUIRED IF HOUSE HAS A POOL.
	2. ( ONE SHEET DMP-2) MARKED IN RED, SHOWER NOT VENTED.
	SINK TO DISCHARGE DOWN STREAM OF BATHROOM GROUP,
	SECTION 909.1.
	PLUMBING PLAN REVIEW BY;
	JOHN LEECH
	805-6695

Review Stop	Z			ZONING
Rev No	3	Status	P	Date	2007-11-30			Cont ID
Sent By	choops			Date	2007-11-30	Time	16:24	Rev Time	0.00
Received By	choops			Date	2007-11-30	Time	16:24	Sent To	E

Notes

2007-11-30 15:46:13	* APPROVED- RESUB #2*



	SENT TO "E" - DP

Review Stop	Z			ZONING
Rev No	2	Status	F	Date	2007-10-05			Cont ID
Sent By	choops			Date	2007-10-05	Time	12:11	Rev Time	0.00
Received By	choops			Date	2007-10-05	Time	12:11	Sent To	E

Notes

2007-10-05 12:12:41	*FAILED - RESUB #1*


	REPEAT COMMENTS:

	1)EXCEEDS MAXIMUM BUILDING HEIGHT.DEVELOPMENT
	REGULATIONS FOR BEAR LAKES ALLOW A MAXIMUM BUILDING
	HEIGHT OF 35' (MEASURED FROM GRADE TO THE MIDPOINT OF
	THE ROOF'S PITCH), WITH AN ALLOWABLE 10% FOR
	ACCESSORIES.YIELDING A MAXIMUM HEIGHT FOR ALL
	ACCESSORIES (NON-HABITABLE TOWERS) OF 38.5' .

	2)AS THE FRONT SITE WALL (COLUMNS) FALLS WITHIN THE
	FRONT UTILITY EASEMENT, ADDITIONAL EASEMENT CONSENT
	FORMS SHALL BE PROVIDED FROM:FP&L, COMCAST/ADELPHIA,
	FLA PUBLIC UTILITIES, AND BELLSOUTH.

	NEW COMMENTS:

	1)INDICATE SETBACK DIMENSIONS FROM TRELLIS TO REAR
	PROPERTY LINE.

	2)PURSUANT TO SECTION 94-302(B)(1) OF THE ZONING AND
	LAND DEVELOPMENT REGULATIONS:RESIDENTIAL FENCE,
	HEDGE, AND WALL LIMITATIONS.
	(1)MAXIMUM HEIGHT.IN RESIDENTIAL DISTRICTS, NO
	FENCE OR WALL SHALL EXCEED SIX FEET IN HEIGHT WITHIN
	REQUIRED SIDE AND REAR SETBACKS. FENCES OR WALLS SHALL
	NOT BE IN EXCESS OF 48 INCHES IN HEIGHT WITHIN THE
	REQUIRED FRONT SETBACK. HEDGES SHALL NOT EXCEED TEN
	FEET IN HEIGHT IN ANY REQUIRED SETBACK.

	NOTE:PALM TREES DO NOT COUNT TOWARDS THE REQUIRED
	FLOWERING/FRUIT TREE REQUIREMENT FOR OPEN SPACE.CHECK
	THAT REQUIREMENT IS STILL SATISFIED.


	QUESTIONS/COMMENTS, CONTACT CHRIS HOOPS, ZONING
	TECHNICIAN
	(561)805-6720

Review Stop	Z			ZONING
Rev No	1	Status	F	Date	2007-08-24			Cont ID
Sent By	choops			Date	2007-08-24	Time	11:12	Rev Time	0.00
Received By	choops			Date	2007-08-24	Time	11:12	Sent To	E

Notes

2007-08-24 11:24:13	*FAILED*


	1)EXCEEDS MAXIMUM BUILDING HEIGHT.DEVELOPMENT
	REGULATIONS FOR BEAR LAKES ALLOW A MAXIMUM BUILDING
	HEIGHT OF 35' (MEASURED FROM GRADE TO THE MIDPOINT OF
	THE ROOF'S PITCH), WITH AN ALLOWABLE 10% FOR
	ACCESSORIES.YIELDING A MAXIMUM HEIGHT FOR ALL
	ACCESSORIES (NON-HABITABLE TOWERS) OF 38.5' .

	2)PROVIDE A LANDSCAPE PLAN SHOWING COMPLIANCE WITH
	SECTION 94-442 OF THE CITY OF WEST PALM BEACH ZONING
	AND LAND DEVELOPMENT REGULATIONS.

	3)SHEET AS.0 SHOWS A GENERATOR AND POOL EQUIPMENT.
	PLANS SHALL REFLECT THESE TO BE PERMITTED SEPARATELY.

	4)SHEET AS.0 APPEARS TO SHOW A FRONT SITE WALL.IF
	INCLUDED IN SCOPE OF WORK FOR THIS PERMIT, AN ELEVATION
	OF PROPOSED WALL SHALL BE SHOWN AND AN EASEMENT CONSENT
	FORM FROM THE CITY OF WEST PALM BEACH DEPARTMENT OF
	PUBLIC UTILITIES SHALL BE APPROVED AND SUBMITTED. NOTE:
	IF SITE WALL FALLS WITHIN THE FRONT UTILITY EASEMENT,
	ADDITIONAL EASEMENT CONSENT FORMS SHALL BE PROVIDED
	FROM:FP&L, COMCAST/ADELPHIA, FLA PUBLIC UTILITIES,
	AND BELLSOUTH.


	QUESTIONS/COMMENTS, CONTACT CHRIS HOOPS, ZONING
	TECHNICIAN
	(561)805-6720